Search Documents

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By J. W. Meier, J. O. Edwards, R. C. Bell

"IntroductionTHE DIE CASTING industry .as we know it today is the direct result of the invention and development of die casting machines during the nineteenth century and of reliable alloys in the twentieth. The early machines were designed to cast low melting point metals such as lead .and tin, and their alloys.It was inevitable that, as these die castings were put into service, the demand should arise for stronger materials. Zinc alloys, often containing lead, tin, copper, and aluminum as major constituents, were relatively easy to cast and stronger than the lead and tin alloys. However, it became apparent after a number of years that these zinc alloys tended to become brittle, distort, and corrode, particularly if kept in warm, humid atmospheres. Thus, considerable quantities of zinc-base .alloys were in use before the trouble was realized and effective measures could .be taken to determine the cause of the instability.The deleterious effect of certain metallic impurities on the properties of zinc •die casting .alloys has now been known for about thirty years. Brauer .and Peirce, and, later, other research workers of the New Jersey Zinc Company such as Anderson and Werley, discovered the pronouned effect of lead, cadmium, and tin on the stability of zinc-alloys."

Jan 1, 1952

By Jonas Olsson

"The picture of China as an antiquated continent is changing rapidly and fast-forwarding progress is a fact in most infrastructural fields. Mining is not an exception. China is today the largest producer of aluminum, coal, steel, zinc, tin, lead and manganese and the country’s mineral resources comprising approximately 12% of the global reserves ranks them number three in the world after US and Russia.In order to feed the growth industry is needed to take extra ordinary strides to improve supply of raw material and Chinese mines are continuously being upgraded with the latest western technology to meet the increasing domestic demand of base metals.In Anshan located in China’s northeast province Liaoning we find one of the fastest developing mining companies, Angang Iron & Steel Group Co. Ltd. With their six mines that together process approximately 60 M ton iron ore/year Angang Iron & Steel Group Co. Ltd is the largest iron ore company in China. The group’s thorough pre-studies and technical evaluations over the past five years have made them very successful in both plant upgrades of existing operations and green field projects.INTRODUCTIONWe live in a time when the world market is gradually acclimatising to the global consequences of “The China effect”. An effect caused by a formerly sleeping giant nation that during the last years has awakened and developed beyond comparison, primarily because of booming infrastructure projects and demand for capital and consumer goods"

Jan 1, 2006

By Albert S. Konselman

This paper describes the mining methods and operating costs for 1938 at the South Burns shaft, situated in the Cripple Creek district, Colorado. The shaft is operated by Golden Conqueror Mines, Inc., through which portions of the properties of the Acacia Cold Mining Co., The Free Coinage Gold Mining Co., and The United Gold Mines Co. are worked under lease. During 1938, 30,773.61 dry tons of ore averaging $9.59 in gold per ton was mined. Of this, 10,138.439 tons averaging $10.65 per ton was produced on company account, and 20,635.171 tons averaging $9.05 per ton was produced by "split-check" lessees.

Jan 1, 1940

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By Luis Palacios Valdivieso

Ante la crisis minera desarrollada en la mina Condestable, se evaluó los factores técnicos, operativos, social y laboral que intervienieron en su decadencia. En este sentido, el objetivo del presente trabajo radica en describir los recursos de estrategia gerencial minera para superar las dificultades de productividad minera a través de cinco temas: cambios en los métodos de explotación, variación de la concepción geológica, proceso metalúrgico, optimización de rendimientos de los recursos y política sociolaboral. Asimismo, se muestra el programa de inversiones que la empresa ha logrado superar paulatinamente ante la crisis del precio del cobre.

Nov 24, 1993

By T. T. Tigert

INTRODUCTION THE PURPOSE of this article on methane is to present the simple basic facts of the characteristics, detection, occurrence, and control of this natural gas in metal mines, so that operators and .safety men may deal with it with some degree of confidence. Fortunately, although methane has been noted at many metal mines throughout Canada, the occurrences usually are small flows of short duration, and the ignitions experienced have, in most cases, had minor consequences. However, methane does present a hazard that can be of serious proportions, and ?any complacent attitude toward this gas that might exist in the minds .of people engaged in underground mining operations should be dispelled when it is ,pointed out that, in Ontario alone, ignitions of this gas have resulted in at least four fatalities, and eight men seriously injured and burned, during the past three years. lt is well-known that liberation of methane can and does .occur suddenly, often in mines where no gas has been found before, and that many ignitions and explosions have occurred in so called non-gassy mines. In view of this, it is apparent that no mine can, with any degree of certainty, be classified as non-gassy. CHARACTERISTICS OF METHANIZ The characteristics of natural gas encountered in most of the Ontario mines indicate that methane is the chief constituent. Methane (CH4), commonly termed 'marsh gas', and by the coal miner 'firedamp', is a colourless, odourless, and non-poisonous gas considerably lighter than air, and is the explosive gas frequently found in coal mines. Its physiological effects, closely resemble those resulting from nitrogen.

Jan 1, 1951

By Axel Preusse

This paper shows basic considerations about the prognosis and prediction of surface subsidence and other ground movements in the German hardcoal industry. The following case studies describe experiences collected in projects between university and industry.

Jan 1, 2000

By P Mitchell, J Proffett, I Munajat

Batu Hijau is an island arc porphyry copper-gold deposit located in the southwest corner of Sumbawa Island in the Sunda-Banda archipelago of Indonesia. Southwest Sumbawa Island is underlain by Early Tertiary, low-K calc-alkaline to weakly alkaline volcanic and intrusive rocks. Within the mine area the oldest exposed rocks are medium- to thick-bedded, medium to coarse andesite volcanic lithic breccia, thin bedded, fine-grained volcaniclastic sandstones and mudstones and hypabyssal porphyritic andesite. In the eastern portion of the mine area there is a thick sequence of quartz diorite that postdates the andesites. A small stock of Equigranualar Quartz Diorite predates the Batu Hijau deposit and occupies the contact between the andesitic volcaniclastic sequence of rocks and the Porphyritic Quartz Diorite. Batu Hijau is a world-class copper-gold deposit that has a drill indicated mineable reserve of 914 million metric tonnes grading 0.525 per cent copper (10.58 billion pounds copper) and 0.403 g/t gold (11.8 million ounces gold). Mineralised material not in reserve accounts for an additional 580 million metric tonnes at 0.328 per cent Cu (4.19 billion pounds copper) and 0.171 g Au/T (3.19 million ounces gold), and including an oxide copper resource of 57 million tonnes at 0.37 per cent Cu and 0.12 g Au/T. Copper and gold mineralisation is directly related to quartz veining and wall rock alteration that developed with multiple tonalite porphyry intrusions. The tonalites were emplaced along the contact between the andesitic volcaniclastic rocks and quartz diorite intrusives. Copper and gold are zoned around the porphyry intrusions, which are designated by their contact-age relationships and other features as Old Tonalite, Intermediate Tonalite(s), and Young Tonalite(s). The Old Tonalite was the first copper-bearing intrusion, and although it is the smallest intrusion it has the highest quartz vein density, the strongest alteration and the highest grade. At least two tonalite porphyry intrusions followed the emplacement of the Old Tonalite. Each of these intrusions was associated with less quartz veining, weaker hydrothermal alteration and lower grade copper and gold than the previous intrusion. The intrusive cycle culminated with the emplacement of the Young Tonalite, which contains relatively few quartz veins, is weakly altered and mineralised. Hypogene hydrothermal alteration and sulphide mineralisation developed in five temporally and spatially overlapping stages. These stages consist of Early, Transitional, Late, Very Late, and I Zeolite alteration. Early alteration and sulphide mineralisation accompanied each tonalite porphyry intrusion, but with diminished intensity in each subsequent intrusion. Transitional and later stages of alteration and mineralisation postdate the tonalite porphyries and overprint Early stage alteration and mineralisation. Early alteration and mineralisation consisted of biotisation, secondary magnetite and plagioclase development, fine porphyry-style stockwork veining and ore mineralisation. Magnetite-biotite????quartz stringers and dark micaceous (biotite-sericite) veinlets were developed. The veinlets were accompanied by biotisation of magmatic mafic minerals and groundmass. Thin, irregular and discontinuous æAÆ type quartz veinlets and fine-grained chalcocite, digenite and bornite mineralisation accompanies the Early alteration. It is hypothesized that most of the copper mineralisation was originally deposited as bornite, digenite and chalcocite. Secondary plagioclase was added along the selvages of the early quartz veinlets. Early alteration is pervasive within and proximal to the tonalite porphyries. In the distal portions of the deposit, andalusite and anthophyllite formed at intermediate to shallow depths, and in the deeper portions of the deposit, respectively. The andalusite and anthophyllite probably developed at the same time as the early magnetite-biotite-quartz alteration in the core of the deposit. Transitional-age alteration consists of oligioclase/albite-sericite-chlorite- quartz-¦vermiculite and is associated with æBÆ quartz veins. Through-going planar æBÆ veins are thicker than æAÆ and æA-familyÆ veinlets and have chalcopyrite????bornite along vuggy centrelines and narrow oligioclase????albite alteration envelopes. Rare æCÆ chalcopyite¦quartz veinlets were also formed during Transitional alteration. During Transitional alteration early copper sulphide minerals (chalcocite, digenite and bornite) are converted to bornite and chalcopyrite. The majority of the copper (50 - 70 per cent) in the deposit is contained in ores in which chalcopyrite is the predominant sulphide. Late alteration consists of feldspar destruction and replacement by sericite and other minerals. The late alteration is accompanied by the development of æDÆ sulphide veinlets and veins. These veins consist of pyrite and quartz????chalcopyrite. Within the halos of the late pyritic veinlets biotite is replaced by sericite, quartz-sericite, quartz-andalusite, or quartz-pyrophyllite+kaolinite replace plagioclase, and magnetite is converted to specularite and/or pyrite. In the periphery of the deposit, the feldspar destructive alteration, together with outer zones of Transitional-age alteration, constitutes what is commonly referred to as a æpropylitic zoneÆ. Very Late hydrothermal alteration is also characterised by feldspar destruction, but differs from Late alteration in that feldspar is replaced by smectite in association with sericite and chlorite. Sulphide mineralisation in this stage consists of sphalerite, galena, tennantite, pyrite and chalcopyrite. The last stage or I Zeolite alteration consists of low-temperature, open space filling consisting of stilbite or laumontite¦calcite. Supergene oxidisation of the orebody extends to a maximum depth of 210m. Isolated deep oxidation occurs along open fracture zones to depths of ~400 metres along æDÆ vein filled fracture zones. Weak supergene copper enrichment occurs in a thin horizon (15 to 60 m thick) that blankets the top of the deposit. The main supergene copper mineral is secondary æsootyÆ chalcocite replacement of sulphide grains and as veins.

Jan 1, 1999

By A. Baldwin

This report describes the engineering feasibility and economic advantages of a unique new mining machine using cutting bits that take a constant-depth linear cut in the coal face. The studies show that this innovative new cutting concept, being developed by the Bureau of Mines, can be designed into the basic continuous mining machine. The resulting miner would be attractive to mine owners because coal could be mined with minimum generation of airborne respirable dust, substantial increases in productivity, and elimination of methane ignition due to cutting.

Jan 1, 1977

By Lin-fang Shen, Shao-jun Li, Zhi-liang Wang

"The meso-structure of real soil consists of numerous particles with different sizes, while the traditional reconstruction method of quartet structure generation set (QSGS) produce relatively uniform soil particles resulting in significant discrepancy between the actual structure and reconfiguration model. In order to remedy the deficiency, the QSGS is improved by considering the influence of porosity and autocorrelative function of soil, which make the models closer to the real soil. Based on the reconfiguration model, Lattice Boltzmann method is combined in the algorithm to conduct further simulation of fluid flow in soil pores. The D2Q9 model is applied to construct the two dimensional model for simulating mesoscopic seepage field of saturated soil by setting the non-equilibrium extrapolation scheme at the inlet and outlet boundary, and the bounce-back scheme at the soil particles boundary as well as the left and right boundary. According to the case study, the proposed program is realized to simulate mesoscopic seepage field of reconstructed soil with constant inlet seepage velocity. The results show that the seepage direction of soil is along the passage with good connectivity, therefore the permeability is controlled by these passages. The seepage velocity in such channels is faster than in bad connectivity channels. Even if the channel has larger pores, the seepage velocity is still small. INTRODUCTIONUnderstanding the seepage mechanism in porous materials is significant in both theoretical and engineering problems. As a typical porous media, soil consists of solid particles and voids, which form connected channels allowing water to flow through. Such seepage in soil exists widely among geotechnical project of slope, foundation pit, and tunnel, etc. Meanwhile, a number of engineering accidents are caused by limited knowledge of seepage characters in soil (Huang, 2006; Liu, 2013). The conventional method in describing seepage features mostly based on the parameter of permeability, which is a macro statistic mean evaluating the whole connectivity of soil. Obviously, this parameter cannot exactly reflect the details of how water flows through the inner soil structure, especially the flow velocity in local mesoscopic area, hence is unable to represent the actual seepage properties. Therefore, it is necessary to develop mesoscopic approaches to fully study the seepage mechanisms."

Jan 1, 2015

By P. Syrjänen, Lovén. P.

Because geostatistics together with block modeling has not been studied in detail before in the rock mechanics, a two-year research program to investigate the practical use of geotechnical modeling was started in Finland in 1999. According to research work results block modeling gives good estimate of overall rock mass quality but it can not identify individual structures like faults and narrow weakness zones. Weakness zones and faults should be mapped from drill cores, surface mapping, geophysical methods etc. and manually generate 3-D structural model. Rock mechanical 3-D modeling can be used for preliminary stope dimensioning and preliminary reinforcement design. Detailed design needs rock quality mapping from drifts during excavation work. La géostatistique associée à la modélisation par blocs n'ayant pas été étudiée en détail jusqu'à présent dans la mécanique des roches, un programme de recherche sur deux ans visant à examiner l'utilisation pratique de la modélisation géotechnique a été lancé en Finlande en 1999. D'après les résultats des travaux de recherche, la modélisation par blocs donne une bonne estimation de la qualité générale de la masse rocheuse mais elle ne permet pas d'identifier les structures individuelles comme les failles et les zones géologiquement dégradées étroites. Ces zones et failles devraient être cartographiées à partir de carottes de sondages, d'une cartographie de surface, de méthodes géophysiques, etc. et générer manuellement un modèle de structure 3D. La modélisation mécanique des roches en 3D peut être utilisée pour un dimensionnement de la chambre et un plan d'armature préliminaires. Un plan détaillé nécessite l'élaboration d'une cartographie de la qualité des roches des galeries lors des travaux d'excavation. Da man früher Geostatik und Block-Modellieren in der Gebirgsmechanik nicht detailliert untersuchte, wurde 1999 in Finnland ein zweijähriges Untersuchungsprogramm in Angriff genommen. Aufgrund der Untersuchungsergebnisse ergibt das Block-Modellieren eine gute Beurteilung der gesamten Gebirgsmassenqualität, kann jedoch einzelne Strukturen wie Verwerfungen und kleine Schwachzonen nicht identifizieren. Schwachzonen und Verwerfungen müssen demnach aus Bohrkernen, oder mit Hilfe von Oberflächenkartierung, geophysischen Verfahren usw. ermittelt und danach ein 3-D-Strukturmodell manuell erstellt werden. Felsmechanisches 3-D-Modellieren ist für die vorbereitende Abbaudimensionierung und für die vorbereitende Bewehrungsplanung verwendbar. Ein detaillierter Entwurf benötigt die Kartierung der Gesteinsqualität aus den Gesteinsstrecken während der Ausbrucharbeiten.

Jan 1, 2003

By Franco Gandin

With increasing demands for highly performing and at the same time efficient and running-costs saving vacuum-degassing equipment, dry mechanical pumps have been confirmed a proper choice to completely fulfill the expectations of steel-making companies worldwide. Regarding the production of both special carbon steel and stainless steel grades, the usage of mentioned pumps allowed reaching simultaneous remarkable results from different viewpoints in various Danieli worldwide installations (treating up to 200 t of liquid steel). As a matter of fact, in front of the replacement of a widely spread and renowned technology such as steamejector pumps with the recently developed technology embodied by the dry mechanical pumps, well-established metallurgical performances in terms of carbonhydrogen- nitrogen-sulphur removal have been repeatedly attained while meeting at the same time the client’s expectations concerning, for example, running-costs and push-button availability. Additionally, thanks to the very flexible, modular, redundant and maintenance-friendly equipment design, random problems occurring to the singular mechanical pumps can be easily solved without affecting the VD-VOD plant availability and metallurgical performance. With a particular regard to the VOD process, a very short overall process-time has been repeatedly performed (averagely less than 58min under-vacuum time at ChMP1) while guaranteeing the expected required quality of the final refined stainless steel. Moreover, in several VOD installations (ranging from 6 t up to 110 t of liquid steel) an efficient automatic process control such as dynamic pressure-regulation during oxygen-blowing has been attained thanks to the controllable variable-speed drives with which each mechanical pump is provided.

Aug 17, 2017

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson, W. Hasz

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a fill-size shaft are underway.

By Caibin Wu, Chengfang Yuan, Jiaqi Tong, Zhilong Cheng, Ningning Liao, Chong Zeng

In a series of Julius Kruttschnitt size-dependent breakage models, the cumulative percentage passing 1/10 of the initial size is used as a fineness indicator for scientific research and the selection of grinding equipment. However, in industrial practice, it is quite customary to use the mass percentage passing 75 μm as the indicator. In this paper, based on the energy-particle size model, quartz and calcite, two materials with distinctly different hardness, were used as test samples in a conical ball mill. At the same specific energy, the value of the cumulative percentage passing 1/10 of the initial size decreased while that of the mass percentage passing 75 μm increased with finer feed size. The experimental test values of the mass percentage passing 75 μm have a good linear relationship with the model predictions, which suggests that the particle size energy relationship of the mass percentage passing 75 μm and Ecs can be used instead of the cumulative percentage passing 1/10 of the initial size and Ecs. By building family curves, when particle size x < 300 μm, the family curve can be well fitted, and the fine particle size distribution of the whole product can be reconstructed.

Dec 22, 2022

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By Robert Martin

New Millennium ?a new project for an experienced mine building team ?Owns 100% of KeMag(Harris Lake) property ?Owns 80% of LabMag(Howells River) property -20% owned by Naskapi Nations of Kawawachikamah ?All founding directors are mining professionals : Geologists or Mining Engineers ?All have extensive experience in the iron ore industry ?The Project Office is located in Montreal, lead by a team of experienced iron-ore professionals Project Overview Geology & Resources Market Prospects Process & Product Development Development Plan Questions

May 1, 2007

By T. P. Meloy

A methodology is presented for finding feasible or locally optimal designs in the class of homogeneous, countercurrent, processing networks performing two-component non-sharp separations. The advantage of the methodology developed here is that given a set of independent performance criteria (specifications such as network separation factor, beneficiation ratio or recovery), a feasible or locally optimal countercurrent network design meeting those criteria can be found in one step. In the methodology, graph-theory was used to explicitly obtain the exact network responses of specific countercurrent networks. These responses were used to formulate the linear recursion equations whose solution gives the expressions for the countercurrent network responses which are a function of the stage transfer functions for two-component, non-sharp separations. These expressions are also functions of the network variables n and c. These expressions, together with the set of independent design criteria, were solved simultaneously for n and c using the Levenberg-Marquardt algorithm for systems of constrained, non-linear equations. The network variables n and c embody the coded network design information which is used to find the feasible network design which satisfies the set of independent performance criteria.

Jan 1, 1994

By J Brisebois

The Wisemans Creek derelict mine site is located in native forest approximately 150 km west of Sydney. Mean annual rainfall at Bathurst, 20 km to the north, is 634 mm and reasonably distributed throughout the year, with slightly more rain falling in the summer months. Evaporation is 1350 mm per annum and considerably exceeds rainfall in all but the winter months (May to August). This results in a water deficit for much of the year. Groundwater is relatively deep, as it has not been intercepted in the shallow open cut workings. Investigation of the groundwater regime was beyond the scope of the current study. Mining has taken place on the site for almost 100 years, during which copper, talc and gold have been sequentially extracted from surface and shallow underground workings. The site is now characterised by the presence of small open pits, unprotected shafts and adits, mullock heaps and an unconfined tailing deposit from a small cyanidation plant. From a distance, the mine area is visible because of two distinct steep bare slopes below the relatively small mine workings and mullock heaps. The mining area was characterised in terms of its environmental, safety and heritage issues. Mullock from the early copper mining was found to be acid forming and leachate from this, combined with clearing of timber, has most likely resulted in death of vegetation below the heaps. The mullock also contains elevated concentrations of heavy metals. The gold tailing is apparently benign and not acid forming, although there are indications of oxidation and acid formation in the derelict gold open cut. Oxidation of the acid forming mullock still appears to be taking place even after being exposed to the atmosphere for at least 50 years, resulting in continued contamination of the slopes below the heaps with heavy metals. The concentrations of metals decreases with distance below the mullock heaps and also is confined to the ground surface the further away from the mullock, providing further evidence to support the theory that the mullock is the source of contamination. Despite this continuing contamination, its spread beyond the immediate mining area appears to have been limited because of the relatively dry climate, with only intermittent rainfall and stream flows. Irregular storm flows in the nearby creek could also have washed any contaminated soil some distance from the site and beyond the area investigated in this study. Remediation of the site and restoration of vegetation on the bare slopes will therefore depend on elimination of the source of acid and metals. Options for remediation, focussing on minimising cost by retaining the materials on or close to the site, are identified. The volume of the open cuts would appear to be close to that required for burial of the acid-forming mullock, thereby removing the source of surface contamination while keeping it above the groundwater table. However, implementation of this remediation plan will depend on the availability of funds to undertake the work through the New South Wales GovernmentÆs Derelict Mines Program.

Jan 1, 2003

By A. E. Hall

"This paper summarizes findings of a two-month investigation in Zambia and Zimbabwe and a one-month visit to Britain in1990-1991. United States contacts have supplied information about that country.Zambia&apos;s political unrest and severe devaluation, combined with developments in Namibia and South Africa, enhanced staff recruiting problems in the School of Mines. Zimbabwe has a strong and developing mining department. The departments of mining in the United States and Great Britain are readjusting and contracting due to the reduction in the scale of the industry.The above factors are reviewed and their impact on the countries evaluated.IntroductionCanada trains the majority of its mining engineers domestically but a significant number are recruited from other countries. Examination of the qualifications of 200 professional engineers registered in the mining discipline in British Columbia showed that125 received their first degree from a Canadian university, 33 graduated from institutions in the United States and 42 from the rest of the world including 30 from the United Kingdom. This is a rough and-ready sample but it indicates that developments in the education of mining engineers in the United States and in Britain are relevant to the Canadian mining industry.The recent changes in the world economy and political structure have significant implications for the mining industry and for the supply and training of engineers. Change in eastern Europe coupled with the downturn in mining, especially in the European coalfields, has enabled many engineers to travel freely to the West. The low gold price and the legislative changes in Africa that have improved access to education for Africans with the ability to fill responsible positions, have reduced the South African mining industry’s overseas recruitment to a minimal level. The Australian recession has also lowered their recruitment of mining engineers from other countries."

Jan 1, 1993