Search Documents

By A. Desbiens, A. Pomerleau

During the summer of 1994, a new PID-based control strategy was installed on line B of the grinding circuit at the Kidd Creek Division of Falconbridge Ltd. Part I of this paper described the methodology used to select the appropriate control strategy using a phenomenological dynamic simulator. Part II presents the implementation of the control strategy. Prior to the controller installation, it was necessary to solve various problems related to the process, such as a cyclic behaviour of the rod mill feed tonnage, a problem related to the mill water source and the calibration of the flowmeters. Once these problems were solved, the control strategy was accomplished in two steps. Step 1 corresponds to the installation of control loops to regulate the pump box level and the cyclone overflow density. Step 2 describes the implementation of a loop to control the cyclone feed density. According to Part I, a loop to control the circulating load is also part of the original design. However, reasons are given to explain the rejection of this loop. For both steps, technical procedures such as filtering, process identification and controller tuning are detailed. Finally, the operator’s interface is briefly described.

Jan 1, 1997

To reduce operator exposure to noise from vibrating screens at coal preparation plants. Background Hearing loss is one of the most common occupational illnesses in the United States. In the U.S. mining industry, hearing loss is 2.5 to 3 times greater than what is expected for the average population that is not exposed to occupational noise. Furthermore, studies by the National Institute for Occupational Safety and Health (NIOSH) showed that by age 50, 90% of coal miners have a hearing impairment versus only 10% of the population that is not exposed to occupational noise. A NIOSH cross-sectional survey of coal preparation plants showed that 43.5% of employees were overexposed to noise. The study also found that vibrating screens were one of the top five loudest types of equipment at these plants?as well as the most numerous?making them a key noise source to address.

Nov 1, 2009

By Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications sys tem which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a relatively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurement s of ambient surf ace electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal- to-noise ratio at the surf ace. Numerous C .W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surf ace magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null is the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken Into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

Jan 1, 1974

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

By John L. Dahle

This report documents the research efforts that were undertaken to design, install and test noise abatement devices for use on off-highway haul trucks operating in surface mines. The objective of the program was to reduce the environmental noise from haul trucks. The noise reduction devices that were developed utilized existing technology and were tested on a 50-ton haul truck. The efforts emphasized the reduction of noise emitted from the engine compartment which included the use of side shields, sound absorbing material, improved radiator shroud design, and a modulating clutch fan. Noise tests were conducted using modified SAE test procedures for measuring sound levels around a stationary and moving machine, and inside of the operators compartment. Test results showed a maximum of 4 dB(A) reduction measured 16 feet from the truck. Interior cab noise was reduced 6 dB(A) with the windows and vents closed.

Jan 1, 1983

By R Schmitt, Y Ghorbani, I McElroy, N J. Bolin, M Parian

Aitik is a large copper porphyry type deposit located in northern Sweden, currently exploited at an annual rate of approximately 45 Mt. The ore’s exceptionally low head grade of 0.25 per cent Cu and varying degrees of hardness across the entire deposit pose challenges to the two fully autogenous grinding lines, each of which comprises a primary autogenous mill in series with a pebble mill. The variability in ore grindability frequently leads to fluctuations in mill throughput. Within the framework of a geometallurgical approach, the present study investigated the relationships between ore grindability and modal mineralogy. For this purpose, drill core samples from different lithologies were subjected to Boliden AB’s in-house grindability tests. This fully autogenous laboratory-scale test generates a grindability index mainly related to abrasion breakage, which is a significant breakage mechanism within autogenous mills. The test results suggested divergent degrees of grindability within and across the selected rock types. A combination of scanning electron microscopy, X-ray powder diffraction, and X-ray fluorescence analyses was performed for the grinding products and bulk mineral samples. The resulting mineralogical and elemental properties were subsequently correlated to the parameters from the grindability tests. It was shown that the main mineral phases, such as plagioclase, quartz, and micas, correlate well with the grindability indices. Similar correlations were found regarding the sample’s chemical composition, attributable to the main mineral phases. A further inverse correlation was established between the sample’s calculated average Mohs hardness and the grindability indices. Moreover, mineral liberation information provided by scanning electron microscopy was associated with the parameters mentioned earlier. The identified relationships between grindability, modal mineralogy, and element grades may help Boliden develop a predictive throughput model for Aitik based on the mine’s block model.

Aug 24, 2022

The problem of separating the constituents of a mixed gas has assumed increasing importance to chemical technology during the last several decades. Metallurgical practice, dealing mostly with the application of gases as fuel, such as for the oxidation or reduction of ores, has not often confronted an important need for such separations. If theory occasionally has indicated advantages in the use of purified or separated gases, as for example the "dry" blast for the iron furnace or oxygen-enriched blast for a variety of smelting operations, the economics of the proposals has not often been satisfactory. It has seemed evident that the practice of the chemical plant was too expensive with regard to installation or material costs, or both, for the needs of the basic smelting industries and indeed was applicable commercially to metallurgical purposes only when the metals in question were especially valuable or pure. This bulletin deals with a new mechanical means of attacking the problem of separation. Although it is improbable that any one type of separation could hope to find universal application, the method described is to be regarded as an alternative to conventional means that has attractive possibilities in certain instances. It extends the number of methods previously available by one that has not before been applied commercially and that utilizes a well-known property of gases that never has received effective technologic attention.

Jan 1, 1940

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

Objective: To enable mine operators and mine inspectors to make quick and accurate measurements of the explosible nature of coal and rock dust mixtures.

Jul 1, 2008

By I. Çinar

Cappadocia is not only a region of Turkey with historical and touristic importance. During the cutting and processing of volcanic tuff, quarries in this region release large amounts of tuff into the environment that is viewed as waste. The release of this waste constitutes an economic loss and contributes to environmental pollution. However, through experimentation with deformation, weight per unit of volume, water absorption, uniaxial compression strength, modulus of elasticity, and point load strength index, volcanic tuff and marble dust composite materials can be produced for use in the building sector. In this study it was observed that, as the percentage of volcanic tuff dust in the mixture increased, the water absorption rate of the material increased, and uniaxial compression strength and point load strength decreased. The produced composite samples used in this study were kept for a predetermined number of times per day, and no deformation in the surface characteristics of the materials was observed. In a statistical parameter analysis, averages, variances, standard deviations, coefficients of variation, and skewness coefficients were calculated. Covariance changes between experimental parameters were also determined. In this study, two types of volcanic tuff dust, that is, yellow and red, were produced during the production of tuff-marble dust composite material. When the percentage of either type of volcanic tuff dust was increased, an increase in water absorption was observed. It was also observed that when the percentage of volcanic tuff dust was increased, uniaxial compressive strength and point load strength decreased. Furthermore, the physical and mechanical properties of the materials obtained by mixing different colored tuff powders and marble powders in different proportions were evaluated using statistical parameter analysis.

Mar 5, 2025

By F M. Senda

This paper highlights strategies used at the Barrick operated Kibali Gold Mine (KGM) to improve the drilling accuracy and blasting effectiveness for longhole open stoping. The mine currently uses Solo DL421 for the required stope drilling and has experienced an average deviation of 10 per cent. Strategies are raised to eliminate or at least mitigate the adverse effects of blasthole deviation and the impact of blasting induced effect at the stope faces including the stope crown. The integration of deviation trends in the design would allow the actual blastholes to be established within their required positions to then facilitate a proper energy distribution with the eventual production blasting. The implementation of stope undercutting reduces the hole length from 35 m to 30 m which in return decreases blasthole deviation by 3 per cent. Another strategy adopted to improve the drilling accuracy is to slow down the penetration rate with the use of several operating approaches, including 135 MPa percussion pressure, 65 rev/sec rotation speed and 17 MPa feed pressure. To this penetration rate, a constant k factor is applied to increase the rate when the bedding inclination is less than 45° from the horizontal or when the hole length is under 10 m. This reduces deviation by a further 4 per cent. Where the rock mass is highly jointed it is advised to use the average penetration rate over the entire length of the hole. Furthermore, the paper shows the effect of deviation on the blasting results through a prediction of fragmentation blasting model optimised with reduced deviation and highlights the effect of presplit mining and timing delay on the blasting effectiveness. Although the size pattern increases with deviation, a strategy pertaining to timing delay with blasting would be to align to the work of Grant (1990) where the optimum hole to hole delay is found to be between 7–10 ms/m of spacing, while the optimum delay between adjacent ring varied between 110–160 ms. Stabilisation of crowns and wings will perform with the implementation of presplit blasting.

Mar 29, 2023

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

By Sean Gallagher

This report describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries.

Jan 1, 1989

By D. E. Hulse

"Social License, the consent of the neighbors and community to develop and operate a mine, has received little attention until recently. Though social license is intangible, not having this relationship with the community carries operational and economic risk to a project, potentially including future impairment of the asset. Acquiring and maintaining social license is a long term personal relationship. It requires communication, commitment, consistency, and transparency. This presentation will review the building blocks to acquire and maintain a social license based on experiences with mining projects in Mexico. INTRODUCTION Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them” (Agricola 1556). In 2015 it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate. “Most commonly, the SLO is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders.” (Bice 2014) A generation ago I learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three legged stool is a very stable structure.In 2015 it seems that we have added some other legs to the stool. The JORC code addresses “social, and governmental factors” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves”. The Canadian CIM Guidelines refer to “environmental, legal and social data” (CIM 2003).Compared to these the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the Competent Person."

Jan 1, 2016

By Chas. F. Jackson

During the current business depression the Bureau of Mines has received many inquiries concerning placer mining, the prospects for men of small means to make wages by small-scale placer operations, the locations of placer deposits in the United States, methods of working placers on a small scale, and allied subjects. It has therefore seemed desirable to prepare a circular covering, in nontechnical language, the principal questions which have boon referred to the Bureau of Mines for answer. There are a number of bureau publications dealing with placer mining, most of which are now out of print, but which may be consulted in the larger libraries. Other articles on placer mining nave appeared from time to time in the technical press and several good textbooks have been written on the subject. A partial bibliography of this literature appears at the end of this paper. A recent pamphlet published by the Idaho Bureau of Mines and Geology to assist the prospector and inexperienced small operator has received wide and favorable attention and is recommended as a useful reference. In the present paper no attempt will be made to cover the subject of placer mining in a comprehensive manner, but discussion will be confined to elementary questions of particular interest to persons of limited experience.

Jan 1, 1932

By K M. Cook, D Clark

Fatality prevention and zero harm are key focus areas for resource companies. However, they remain an ongoing challenge for high hazard industries, including the mining sector. As one example the latest International Council on Mining and Metals (ICMM) Safety Performance Report shows that, while there is generally a declining fatality trend since the organisation commenced publishing data in 2012, there were still 33 fatalities across member companies in 2022 (ICMM, 2023b). Every fatal incident brings significant pain and suffering to the colleagues, friends and family of those involved, however the failures and causal factors leading to each incident are frequently very familiar to people working in the industry, particularly those tasked with managing risk and safety. In the words of Dame Judith Hackitt, Grenfell Tower Fire Investigator, ‘there are no new accidents – just different people making the same mistakes because they haven’t learned’ (Hackitt, 2022). The recurring themes in terms of the nature of fatal hazards and their associated causes across the mining sector show that, despite improvements evidenced by the favourable declining fatality trends over the long-term (in general and outside of catastrophic multiple fatality events), changes are required to achieve fatality elimination and the aspiration of zero harm. This extended abstract and the accompanying presentation apply a mining frame of reference to the idea that there are no new accidents, examining how this applies within the industry and why the lessons from past failures are not always well understood or applied to prevent the reoccurrence of material unwanted events. Many contemporary mining and resources organisations have extensive internal incident history data and a wide variety of information on fatality incidents is publicly available, including the annual ICMM Safety Performance Report. This extended abstract and the accompanying presentation explore how this existing data can be used effectively to learn from the past and proposes practical ideas regarding strategies for successful knowledge transfer to the workforce as a key component of preventing history repeating and improving safety performance across the industry. As noted by ICMM, ‘sharing lessons from failure is vital to improving health and safety, but it’s not enough’ (ICMM, 2023a).

Apr 16, 2024

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1981 (October 1, 1980 - September 30, 1981) under its Minerals Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

"Canada Centre for Mineral and Energy Technology (CANMET)Natural Resources CanadaMining and Mineral Sciences LaboratoriesA. Address and Contact Information555 Booth StreetOttawa, Ontario, Canada, KIA OGlWebsite: http://www.nrcan.gc.ca/Contact: Philippe Dauphin, Manager, Business DevelopmentTel.: (613) 947-0798Fax: (613) 947-0984E-mail: pdauphin@NRCan.gc.caB. Type and Size of FacilityScope of facilitiesCrushing from minus 4 in. to 10 mesh; grinding - rod, ball, vibration, SAG and impact mills; classification- screening, cycloning, mechanical, hydraulic and dry centrifugal classifiers; froth flotation - automated, column, and frothless flotation; gravity separation- wet and dry; magnetic separation - high gradient, high and low intensity, wet and dry; electrostatic separation; heavy-media separation; calcining; cyanidation; thickening; filtration; drying - fluid bed and freeze drying; pelletizing; microwave.SpecialtiesMineral beneficiation research and development; flotation of sulphides - flowsheet improvement, selectivity, reagent selection; novel flotation techniques; analysis of thiosalts formation; use of mineral processing techniques for recycling.Specialized equipmentHigh gradient magnetic separation, Denver XRF on-stream analyzer, automated flotation cell.Complementary support servicesElectron microprobe; SEM; STEM; X-ray diffraction; particle size analyzer; mineralogical and analytical chemistry services; physical chemistry; hydrometallurgy; pyrometallurgy; engineering and economic evaluation; mechanical shops; technical information services and library integrated with the National Library System of the National Research Council."

Jan 1, 2000