Search Documents

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

By Satya Ganti, Bryan Turner, Bill Davis, Veeraraghavan Sundar

This work presents a three dimensional microstructural analysis of medium carbon steels, based on serial sectioning using optical microscopy. The microstructural phases considered here are ferrite and pearlite. Typically conventional 2D microscopy is used to analyze these phases (ASTM E112-13 in Standard test methods for determining average grain size. ASTM International, West Conshohocken, PA, 2013), with eddy current (Khan et al. in J Mater Process Technol Freitas et al. in Mater Sci Eng A 527(16):4431–4437, 2010) as alternatives. Medium carbon steel samples were heat treated in a furnace and either slowly cooled in the furnace, or cooled at higher rates. This resulted in different pearlitic microstructures in the samples. The analysis was conducted with Robo-Met.3D®, a fully automated metallography system for serial sectioning. Based on optical microscopy, volume cubes of hundreds of microns on edge were imaged and reconstructed to conduct grain size and phase volume analysis. The system proved capable of collecting image data with high fidelity, and controlled slice thickness in an automated manner. The resultant dataset was useful in visualization and analysis of pearlite and ferrite phases in steel samples.

Mar 1, 2018

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988

By A. C. Fieldner

THE Bureau of Mines has received many requests for Information concerning the methods its laboratories use for analyzing coal and coke and determining their heating value. The fuel investigations now conducted by the Bureau of Mines are an outgrowth of the work undertaken at the Government coal-testing plant erected in 1904 at the Louisiana Purchase Exposition in St. Louis, and the methods for proximate and ultimate analysis of coal used by the Bureau of Mines are based on those originally adopted by the chemists of the coal-testing plant and followed in the subsequent chemical work of the Government fuel-testing plants at St. Louis, Mo., Norfolk, Va., and Pittsburgh, Pa. The many valuable suggestions and criticisms received from N. W. Lord, director of the School of Mines, and from E. E. Somermeier, professor of metallurgy, of Ohio State University, at that time, are greatly appreciated; development of many of the methods for the proximate and ultimate analysis of coal now used by the Bureau of Mines is chiefly clue to these men.

Jan 1, 1951

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By Pedro Henrique L. M. Lopes, Édio Pereira Lima Jr., Fernanda Santos da Luz, Fábio de Oliveira Braga, Sergio Neves Monteiro

Several works have been dedicated to study the ballistic response of multilayered armor systems (MAS), including those using natural fiber composites as second layer. These composites disclosed good ballistic performance, having economic and environmental advantages. In the present work, the objective was to investigate the effect of areal densities of each MAS layer, in the overall performance of a MAS with an alumina ceramic front, a curaua fabric reinforced composite filling, and an aluminum alloy backing the target. Ballistic “backface signature” tests were conducted, varying the areal densities of the MAS layers according to a Box-Behnken design. The results showed a similar influence of the ceramic and aluminum layers in the MAS “backface signatures”, although deformation and failure mechanisms were significantly different. The composite also showed significant participation in the overall MAS performance. Since the composite is cheaper and lighter, a balance minimizing the other layers would be advantageous.

Mar 1, 2018

By Ghassan Skybey

Australian coal mines uses state of the art technology in coal rib reinforcement. This paper highlights the development over the past 15 years in coal rib support technology, along with the advantages and disadvantages of each system. It also outlines the current trend in using coal rib reinforcement in speeding up the dowels installation to improve the current low drivage rate. An innovative cuttable dowel is discussed which improves the drivage rate. This new dowel is self anchoring it uses no resin anchor it has a 5 tonnes (5.51 tons) anchor capacity and can be fully installed in approximately 10 seconds.

Jan 1, 1995

By F. Bourgeois, J. -S. Kroll-Rabotin

ABSTRACT: Falcon concentrators are enhanced gravity separators designed for concentrating fine particles. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidization water. We investigated the physics of particle transport inside Falcon concentrators, and concluded that separation efficiency is governed by differential settling velocity. We derived and published a predictive model of the partition function under dilute conditions. We intend to extend the initial model to concentrated ultrafine suspensions for application to industrial scenarios by adding hindered settling to account for solid concentration effects.

Jan 1, 2011

By K. F. Unrug

The research work reported in in this paper deals with the monitoring of roof behavior in a drift mine located in Eastern Kentucky operating in the Coalburg Seam. The thickness of the seam at the monitoring site ranges between 9 and 10 feet with the immediate roof changing from sandstone to shale then back to sandstone. Shale thickness varies between 0 and 2.5 feet. The characteristics of the immediate shaly roof were monitored with 38 dynamometers which were set up in three survey lines to cover the entire range of shale distribution. The dynamometers are capable of providing accurate load readings in the range of +/- 5 pounds. To closely observe the contribution of moisture toward roof deterioration the dynamometers were set up in intake and neutral airways. A television borescoping camera was used in conjunction with the dynamo- metric instrumentations at pre- determined observation holes to physically observe and record the separation process of the shale and sandstone stratum with respect to time. Monitoring took place between January 1985 through January 1986 in order to cover a full cycle of dry and wet mine conditions associated with the seasonal changes. Analysis of the data show a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1986

By Roger C. Wilmoth

The most common method of treating mine drainage to prevent water pollution consists of neutralization and aeration. This process removes the acidity, iron, aluminum, and some other heavy metals, but does not render a water suitable for domestic or industrial use because of the high dissolved solids, hardness, and sulfate in the treated water. The Environmental Protection Agency (EPA), has been sponsoring and conducting research since 1966 on the use of reverse osmosis (R.O.) for the treatment of mine drainage. This process has been found to be highly effective in the removal of nearly all the dissolved solids. In addition, since R.O. is a concentrating process, potentials for recovery of valuable heavy metals are possible. This paper is a review of the state-of-the-art on the treatment of mine drainage by reverse osmosis.

Jan 1, 1972

By R. E. Perry

To develop new or improved flotation methods for beneficiating low-grade red iron ores, the Bureau made many bench scale and continuous anionic flotation tests on ferruginous sandstones and calcareous iron ores from the north-eastern part of the Birmingham, Ala., iron district. The ores contained about 21 to 36 percent iron, a to 11 percent lime, and 22 to 64 percent silica. Production of iron concentrates containing 48 to 52 percent iron was technically feasible in batch tests, and the iron recoveries ranged from 85 to 92 percent. In continuous tests 49 to 51 percent iron products were obtained with 80 to 90 percent recovery.

Jan 1, 1962

By H. Marquis

The present paper consists of a survey of the literature on the problems of abrasion and wear of metals and materials by suspended matter. This problem is a very general one in industry, and is especially notice-able in the operation of cyclones and other types of dust collectors. The problem of abrasive dust in corrosive gas environments, such as commonly encountered in metallurgical industries, is particularly severe. Very little work has been done in the study of this type of abrasive wear, especially at high temperatures. However, a general review is presented here of all the work published on related subjects, such as that involving sand erosion in turbines and water wheels and the effect of temperature on friction wear. Topics in this paper include: blasting wear by sand, quartz, limestone, silicon carbide and other refractory particles; methods of investigation; effects of velocity, temperature and *Canadian Armament Research and Development Establishment, Valcarter, P.Q. angle of attack; correlation between indentation hardness, scratch hard-ness and resistance to abrasion; the effect of protective coatings; resistance of various metals; etc.

Jan 1, 1962

By C. A. Pryor

The aggregates industry is the largest minerals industry in the United States producing over 2.6 billion metric tons of crushed stone, sand and gravel annually. Approximately 5% of that production is fine material, passing a 75-micron mesh sieve. Of that amount, about 77% is not sold and represents one of the major industry issues. The material accumulates in stockpiles and settling ponds having an operational and economic impact on the site’s bottom line. Many factors cause this material to be produced: from blasting and processing techniques all the way to end use specifications.

Jan 1, 2002

By Edward D. Thimons

This Bureau of Mines report presents expected levels of air pollutants in the face areas of oil shale mines, based upon data collected by the authors and previous investigators. Ventilation requirements to maintain these pollutant levels below their threshold limit values and Federal and local mine air quality standards are discussed. Two practical face ventilation systems are discussed in terms of actual in-mine test experience.

Jan 1, 1986

By Kirtley F. Mather

FROM almost every point of view, petroleum was "strategic mineral number one" during the World War that ended in 1945. Even the spectacular advent of the atomic bomb in the final days of the conflict did not displace it from its position of prime importance, although within a few years uranium will almost certainly be the "number one" material in the minds of military strategists, if it is not even now in that position. But both as fuel and as raw material for chemical industries, petroleum will hold the center of the stage for many years to come. Hardly any other substance illustrates so fully the manner in which science and technology may be combined to achieve the utmost success in contributing to human efficiency and comfort. Fundamental to any understanding of the problems implied by my topic

Jan 1, 1948

By D. E. Calisaya, É. Poulin, A. Desbiens, R. del Villar, A. Riquelme

"A 15 cm diameter by 732 cm height, fully automated pilot column was installed in the Agnico-Eagle’s Laronde concentrator (Québec), for evaluating the performance of newly developed sensors and advanced process control algorithms. For eventual comparison purposes, the pilot column is continuously fed with the same slurry feeding the copper-circuit third cleaner column. It is equipped with electrical conductivity-based sensors for estimating the three variables used in the multi-variable control algorithm under evaluation: froth depth, fraction of wash water underneath the interface and gas hold-up. Froth depth is regulated using a PI controller while a predictive controller is formulated as the minimization of the tracking errors of gas hold-up and bias rate, keeping several operating constraints between their practical upper and lower limits. In particular, an unreachable high set point of gas hold-up can be selected in order to maximize the bubble surface area available for particle collection, while maintaining bias rate above a minimum value required for froth cleaning. The proposed strategy may indirectly help optimizing flotation column operation by using these secondary variables, without the implementation of a real-time optimization layer.INTRODUCTION Flotation columns have already been used for more than 30 years, mainly in cleaning stages, as a result of their froth washing capabilities. Despite their widespread usage, the measurement of some pertaining variables and their use for automatic control is rather scarce. Among the most important variables directly related to the process metallurgy (concentrate grade and recovery), froth depth (hf) is the only one normally monitored and controlled. Even though commercial sensors are available, gas hold-up (eg), a variable directly related to concentrate recovery, is seldom measured and never controlled. Another important variable, bias rate (Jb) responsible for concentrate cleaning, is simply not measured at all, as there is no commercial sensor available. Therefore, besides froth depth, continuous monitoring of process variables is limited to flow rates (gas, feed, tailings, wash water), i.e. to manipulated variables. Some new available sensors have been industrially tested, e.g. the Sonar-TracTM for eg (O'Keefe, Viega & Fernald, 2007) and the McGill hold-up sensor (Tavera & Escudero, 2002). Others, for bias rate and frother concentration, have been successfully validated at laboratory scale by Laval’s LOOP researchers (Maldonado, Desbiens, del Villar & Chirinos, 2008b; Maldonado, Desbiens, del Villar & Aguilera, 2010a). Some devices have been extensively used for monitoring bubble size and space distri-bution, e.g. McGill bubble viewer (Gomez & Finch, 2007) and others."

Jan 1, 2012

The selection and implementation of the right technology for a project is critical to the future development of the resource industry. It is essential for companies to ensure ongoing competitive viability that where practical new or alternative technology be adopted. Analysis of historical data relating to development of resource-based process plants provides an enlightening insight into the key factors which influence their success or failure. The adoption of new technology does not guarantee the success of a project. The outcomes of this analysis have been used to develop some general guidelines and principles the author believes are useful in the selection and implementation of new or alternative technology in resource projects. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By A. S. Dawson

Introduction The purpose of this paper is to discuss, in a general way, the application of geological principles in the exploration for, and development of, deposits of industrial minerals. Mention of geological factors pertaining co specific minerals will be by way of illustration only. Since many prospectors are little acquainted with the geological setting and mode of occurrence of deposits of these minerals, some prospecting possibilities in the field will be pointed out. Geology is a tried and proven tool in the search for and exploitation of metalliferous deposits and of oil and gas fields, but, so far at least as Canada is concerned, only very rarely has a directed, intensive search been made for deposits of industrial minerals. Examples might be cited, however, where, in other countries, such investigations have yielded rich rewards. Thus, development of the vitally important potash deposits of New Mexico was the result of a deliberately planned programme of geological investigation, first by United States Government agencies, and later by private interests. War or the threat of war, or peace-time industrial expansion, can render concentrated exploration for specific minerals desirable or even essential. Such exploration is, primarily, a geological problem. Admittedly, there is in general less scope for the application of geology in the search for, and development of, deposits of industrial minerals than of metalliferous minerals, oil, etc. Where the latter are concerned; the objective of exploration is to find a material that is valuable, within broad limits, no matter where it is located or how it occurs. The unit value of the material is limited only by the amount of the valuable constituent in the formation- its possible upper limit is tremendously high. On the other hand, many industrial minerals constitute in themselves 90 per cent or more of the formation- their amount cannot increase and their unit value is commonly low. Moreover, for commercial exploitation, the deposit must, in general, be reasonably close to markets or to plant or other facilities for processing the raw material, since, owing to its low value, this cannot be transported any great distance. As a consequence, intensive geological search for and investigation of such deposits has been restricted to industrialized areas. Obviously, however, it is good insurance for any operator to understand the geological background of his deposit, particularly in the case of new developments.

Jan 1, 1949

By Adrian Rosen

When one thinks of innovation and leadership in wireless communications, one would rarely consider a potash mine to be leading the way. Agrium Incorporated has proven that they are leaders and innovators, as is evident in their recent deployment of a large-scale 802.11 wireless network in their underground potash mine located at Vanscoy, Saskatchewan. 802.11 is an IEEE standard for Wireless Local Area Network (WLAN) technology. Rather than simply replace an aging communications infrastructure, Agrium chose to let technology provide the framework for future success

May 1, 2006

IT will be noticed, from the following contributed papers on the various plant, what an infinite number of parts are required to be kept in active operation in order to derive a resultant product of commercial value from the ores and materials received at the works. Crude ores and concentrates, in every degree of complex structure and resistance to treatment, are arriving daily from near and distant places, moreover their metallic contents are so varied that an outsider, unacquainted with the operations, would naturally wonder how it is possible that the rare elements are to be sorted out and classified into their true order, to meet industrial requirements.The proposition is necessarily not a simple one and owners of mining properties have naturally refrained from smelting their complex ores on account of the technical difficulties of attaining high efficiency and recovery of the metals, where limitations are imposed in procuring a variation of ores that lead to the best smelting and refinmg result. This difficulty obviously imposes many disabilities on the smelter, who is prepared to accept all such complex ores, and it may be said that were therenot available a large weekly supply of lead concentrates from the company's own mine at Broken Hill, of standard quality, much of the material being treated in the world today would certainly not be marketable.In order to sustain full efficiency, each section of the works must maintain its.true balance and synchronize with the requirements of such other departments as are dependent on its partially treated materials. This harmony of operations is not only imperative as regards tonnage output, but also relies on the condition of the resultant treatment by each plant, no large variations being permissible.The various officers are, therefore, dependent on one another to keep the order of the operations flowing regularly. This is accomplished by constant intercommunication and observation, as...

Jan 1, 1918