Search Documents

By V. Voller

A relatively simple model of grinding which incorporates both the Bond grindability equations and the population balance equations has been extended to form a comprehensive simulation package that can describe most kinds of conventional grinding circuits. The package has two programs, with the first consisting of an input program which helps the user to specify the prescribed circuit, while the second program performs the actual simulation. The package serves two main purposes - i) as a check on mill design, with the output providing not only predictions for the product passing size but also of the full product size distribution, and ii) as a means to assess the likely effects on the product size distribution of operating under different sets of conditions.

Jan 1, 1981

By Denys Parra, Ernesto Nájar, Javier Mendoza

La mayoría de unidades mineras o proyectos mineros en el Perú se localizan a lo largo de la cordillera de los Andes, donde las condiciones del relieve del terreno en algunos casos, hacen difícil la tarea de encontrar áreas con la suficiente capacidad para almacenar relaves convencionales (pulpa o espesados). En otros casos existe la necesidad de recuperar la mayor cantidad de agua, impactar la menor cantidad de área o la escasez de espacios para desarrollar proyectos de instalaciones de almacenamiento de relaves. Bajo estas condiciones la disposición del relave filtrado representa una buena alternativa para el almacenamiento de relaves en varios proyectos mineros.

Sep 1, 2017

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By Jones R. G.

Dr Pat Foster, Senior Lecturer in Mining Engineering at the UK's Camborne School of Mines, talks to Rhiannon Garth Jones about mining safety around the world, education and the future of the industry

Feb 1, 2015

By F. Karakas

Organo-bentonite production enjoys important applications including solvent based paints and, more importantly, the production of polymer/bentonite nanocomposites. Quarternary ammonium salts in this regard are still considered as the most versatile reagents in the process of hydrophobization. In this study, a purified form of Resadiye region bentonites, which is one of the most significant sodium bentonite deposits in the world, was used. The raw Na-Bentonite was typically characterized by chemical analysis, XRD and DTA analysis and more importantly for its cation exchange capacity (CEC). Other technological properties such as swelling index, pH, apparent viscosity, water absorption, oil absorption were also conducted on the raw bentonite. The mineralogical analysis of the raw bentonite reveals that it contains about 80 % montmorillonite together with other associated gangue minerals including feldspar, quartz, calcite, dolomite, coloured impurities and other clay minerals. The raw bentonite was subjected to two stage processing involving a series of hydrocylones. Different apex and vortex diameters and different pressures were employed in order to produce a bentonite concentrate with 95 meq/100g CEC from a CEC of 71 meq/100 g. This high quality concentrate was used in the production of organo-bentontonite. The modification was performed with two different quaternary amines, i.e. Trimethyl Phenyl Ammonium Chloride (TPAC) and Hexadecyl Trimethyl Ammonium Bromide (HDTMA-Br). In the modification procedure, three parameters, i.e., adsorption density, zeta potential, swelling index and apparent viscosity were studied simultaneous-ly from the same suspension to identify both the mechanism of the process and also the degree of hydrophobicity. Adsorption measurements were made as a function of conditioning period, pH, and reagent concentration. Simultaneous examination of the adsorption density, zeta potential and apparent viscosity enabled us to pinpoint the optimum region of hydrophobicity which was subsequently tested by settling and critical coagulation concentration in both water as polar and toluene as nonpolar solvents. The results are analyzed in the light of experimental data.

Jan 1, 2014

By L. S. Montagna, R. M. C. Santana

"Since the industrial revolution, plastic products sector has growing bigly, however this fact presents as consequence the increase of municipal plastic waste (MPW).The aim of this work is to developmet polymer mixture from MPW with the adittion of rubber tire (TR) post use and to study the mechanical and morphologycal properties. The polymer mixtures Polypropylene/High impact polystyrene/TR (PP/HIPS/TR), where rate weight TR used was 10, 20 and 30 % and with three size particles (500, 710 e 1000 µm). The specimen tests were obtained by injection molding. Preliminary results of mechanical properties showed that the increase of TR influence in a reduction of the flexural and tensile resistance. Results by scanning electronic microscopy on the fracture surface of mixtures PP/HIPS/TR showed a better interaction of TR particle with HIPS than with PP. Also, the presence of microcavoids was observed, characteristic in PP/HIPS blends, favouring in the increase of its opacity.IntroductionOne great part of the municipal solid waste (MSW) is composed of polymer mixed since commodity plastics, blend to polymer composite. The processing of plastics mixtures for recycling has been attempted with some success, but poor mechanical properties and uncertain economic value limit their more versatile reuse. Polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET), poly(vinyl chloride) (PVC) and polystyrene (PS) are among the most common plastic waste, predominantly used in packaging food industry [1].One other problem that preoccupy to the society is the increase of rubber tire waste in the proportion of MSW. In Brazil, from 1999 to 2004, 39 % from 386 mil ton of tire post-use were destined to ciment Industry as source of energy [2]. However this destiny produces one other problem, environment pollution, due to gas mixture emitted.Recycling represents a valid alternative to the disposal of post-consumer plastics in common landfills if it is possible to obtain new materials with good final properties compatible with practical and, above all, by cheap methods [3]The reutilization of group tire rubber (TR) powder as a dispersed elastomeric phase in a thermoplastic matrix offers an opportunity to design second generation materials which would be recyclable due to the thermoplastic matrix and which potentially could present thermoplastic elastomer (TPE)-like mechanical behavior. [4]."

Jan 1, 2008

By O. A. Bascur, J. Patrick. Kennedy

"The lack of integration of mining and metallurgical information at sufficient detail to act is a problem. Without such data, mine cut-off grade can not be optimized on a per grade basis. It is difficult to determine economics without integration of mine transactions, stockpile inventories, process flows and assays. Actions also require real time information from manufacturing assets, but corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. Validation methods must include process models to identify corrupt actionable information. This paper presents new tools that use the model the process to sift through available data, identify and eliminate gross errors, and use statistical data reconciliation to create material balanced, internally consistent values. Uses of models allow data to be unified for useby both monitoring and decision making processes.A Real Time Performance Management (RtPM) uses unifying analysis methods to empower everyone in the organization with unparallel real-time intelligence, enabling them to continuously improve performance.BACKGROUNDExtraction of metals has become a global business; new economic and environmental forcing factors are present today which were unheard a couple of years ago that are causing companies to focus on plant operations. High ROI actions can be achieved internally which will increase mining and metallurgical processing unit efficiency and reducing operating costs if the proper information is provided those in the complex that can act. Large changes are possible with many of these small steps if the barriers for action are removed. The chief impediments are lack of infrastructure including the data, computing tools and essential data and bad information.Increased demands will be placed on the types, quantity and priority of information. Metallurgical complexes are attempting to become better neighbors, increase productivity, improve customer service, and satisfy the regulators and compliance groups -- all with fewer people and less costs."

Jan 1, 2004

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By T. F. Mitchell, J. V. Batty, R. R. Wells, R. Havens

"INTRODUCTION )ne of the most important wartime activities of the Bureau of Mines was the search for new sources of minerals necessary to the prosecution of the war. As a part of the investigation of strategic mineral deposits in the United States under the Strategic Minerals Act (Public 117, 76th Cong., 1st Sess., Ch. 190), examining engineers of the Bureau of Mines investigated and sampled various deposits of chrome ore in California, Idaho, Montana, Oregon, and Washington, and those deposits that warranted further study were explored by diamond drilling, trenching, and drifting, as re¬quired. During these investigations, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing results obtained from laboratory ore-dressing studies of the chrome ores submitted.Although the deposits range widely in geographical location, the mineral occurrence of all of them is strikingly similar. Chromium, in all of the ores tested, is present as impure chromite or chromium spinel. Although pure chromite (FeCr204 or FeO.Cr203) contains 68 percent chromic oxide, the iron may be replaced in varying amounts of magnesium, and the chromium may be replaced similarly by aluminum and ferric iron. In studying concentration methods as applied to chrome ores, the composition of the chrome mineral is of fundamental importance, because it is manifestly impossible to produce a high-chrome concentrate from a low-chrome chromite by any mechanical process.In all but one of the ores, the gangue material consists of olivine or altered olivine minerals such as serpentine, antigorite, and chrysotile. The exception, the Antelope or from Montana, has a gangue chiefly composed of actinolite, chlorite, and talc."

Jun 1, 1947

By E. C. W. Perryman

Materials research and development has played an important role in the commercial success of the CANDU- PHW nuclear reactor and in the production of heavy water. Both capital investment and energy conservation demand very high component reliability in such systems. The interactions among reliability, plant performance and economics will be discussed in relation to materials research and development. Likely materials requirements for the nuclear industry over the next twenty five years will also be discussed.

Jan 1, 1977

By Galen H. Clevenger, MARTINUS H. CARON

Although there are exceptions, oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. When these ores are of high enough grade they can be smelted; indeed, some rather low-grade ores of this type have been smelted at a profit because of their fluxing value. In the past, when these ores could not be smelted, they either were not treated or were treated at low efficiency, generally by cyanidation. The need for thorough investigation of the problem was therefore evident for some time before the writers began their research. The problem of treating manganese-silver ores seems to have been recognized first about 35 years ago by C. W. Goodale in applying pan amalgamation at Tombstone, Ariz. He attributed the low extraction of silver to the fouling of the mercury by manganese rather than to the presence of a refractory compound of manganese and·silver. Although definite knowledge as to the cause of the poor extraction of silver was lacking, a more or less effective preliminary treatment, that is, a chloridizing roast, was applied. E. M. Hamilton, in 1909, was perhaps the first to define clearly the problem as it affects the cyanidation of silver ores and to suggest possible methods of preliminary treatment. Most of the work done in the interval between the appearance of Hamilton's paper and the assumption of the investigation by the authors was in the nature of routine tests covering suggestions already made rather than of research directed to a fundamental study of the problem. No practical application has so far been made of any of these proposed processes. The investigation described in this bulletin has proved that there s a refractory compound of manganese and silver-probably a manganite- insoluble in cyanide solution and other common solvents for silver. Although this compound has not been isolated from natural ores, it has been made synthetically, and shows all the characteristics of the natural product. Furthermore the authors have shown definitely that heating in air a relatively small amount of a silver compound with a large excess of silica (in the proportions ordinarily occurring in a commercial silver ore) renders

Jan 1, 1925

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area's northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

By C B. McCampbell, R W. Jr Bickes

Sandia National Laboratories has developed a semiconductor bridge (SCB) igniter for the ignition of a variety of explosive materials. When subjected to a low-energy current pulse, the bridge bursts into a plasma causing rapid ignition of the explosive material pressed against the bridge. Despite the low energies required for ignition, SCB components have proven to be explosively safe, meeting both no-fire and electrostatic discharge (ESD) safety requirements.

Jan 1, 1991

By Marco D. Boscardin

Control and mitigation of building response to construction activities are assuming a greater role in design decisions for underground construction. Alternatives for controlling building response have multiplied with the continued development of ground modification methods, better control of construction activities that cause ground movements, and increased understanding of building behavior and response. This paper describes approaches to estimating building response to construction-related ground displacements caused by adjacent excavation and highlights the discussion with several case history examples. Examples discussed includes experiences with two, seven-story historic structures, supported by timber piles with granite block pile caps, which were underpinned in preparation for ground-freezing ground stabilization and tunnel construction beneath the buildings. The elevation of each building column was monitored and elevation adjustments were actively performed during construction. The second example examines the performance of a slurry wall braced cut, 45 to 50 feet deep penetrating through a stiff crust into a soft clay layer and associated building response. This cut was immediately adjacent to two, approximately 15-story office buildings, which were supported by deep foundations founded in the stiff crust.

Jan 1, 2003

By Adrian C. Dorenfeld

Concentradora "Dana Aida" (100 t/d capacity) was built in 1971-1972 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals from two veins. The veins, Don Felipe and aria are about 150 m apart, but are distinctly different mineralogically. The deposit is near San Juan de Guadalupe, Durango. Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuila. Sampling, ore testing, flowsheet design, plant design, drawings purchasing, financing, etc. was planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1979

By M. W. Von Bernewitz

Fay's glossary3/ of terms contains the following definition of "black sand": Heavy grains of various minerals which have a dark color and. are usually found accompanying gold in alluvial deposits, for example, magnetite, chromite, ilmenite, cassiterite, tourmaline, and others. The Bureau of Mines is issuing this report in answer to the many inquiries from individuals and firms as to how they may treat or sell the heavy black sands that accumulate in the sluice boxes of beach and river placering and to warn such individuals and firms against becoming too enthusiastic over the chances of striking it rich. For a half century or longer much money, energy, and time have been wasted in devising, building, and trying numerous machines to recover gold and platinum, also gem stones, from sand that generally has not been worth the effort. Volumes have been written on the subject, and thousands of letters of inquiry have been received by agencies of the State and Federal Governments. The demand for information has been so great that all of the Bureau's publications dealing wholly or partly with black sands are out of print. They are listed at the end of this report.

Jan 1, 1938

By S. M. Flaherty, R. E. Scheffel, A. Guzman

Geochemical conditions within a leaching operation are heterogeneous. This variability arises mainly from hydrological controls imparted by physical characteristics of the ore and by heterogeneous metallurgical properties at the rock-fragment and industrial heap scale. The resulting chemical conditions are responsible for stratified mineral recovery, non-uniform extraction and prolonged leach cycles. This paper presents field data from a sulfide-leaching operation which clearly demonstrate the impact of chemical heterogeneity on metal recovery and the potential use of modern measuring techniques to facilitate operational monitoring and decision making for optimization of leaching operations.

Jan 1, 2006

By Masayuki Otagawa

THE mining methods adopted in Japanese mines are less known to the mining world than those of other countries, owing to the geographical remoteness, but they present many features of interest to mining engineers. The Ashio copper mine is at the village of Ashio, in Tochigiken, about 109 mi. (175 km.) from Tokyo by the Imperial Government railroad. The area of the concession owned by the Furukawa Mining Co. is 5000 acres (5023 ha.). The mine was formerly divided into three, viz.. Honzan, Kotaki, and Tsudo, which are distant 3 mi. (4.8 km.) from each other as shown in Fig. 1. However, in 1914, when the writer was general manager, the three mining plants were amalgamated into one with the result of simplifying the working projects and increasing the operat-ing efficiency. The mine was visited-by the Institute party in November, 1911, when Mr. K. Inouye was the general manager. Shortly afterward, the writer was appointed manager, and, in 1915, he was succeeded by Dr. K. Asano. At the end of 1917, Mr. K. Kibe became general manager and, after two years, was succeeded by the present manager, Mr. I. Sugimoto-. For some time Dr. J. Kojima was acting general manager. It is needless to say that the gentlemen mentioned are all members of the Institute, as is also Baron T. Furukawa, president of the company. Since the discovery of the enormous masses, called "kajika" or "bullhead" deposits; which the writer has described elsewhere,' the mining methods have been varied to meet the different conditions presented by these deposits.

Jan 2, 1922

By R. Minto, W. G. Davenport

The slag removed from the reverberatory furnaces of copper smelters contains significant copper values. A serious financial loss is involved, as further recovery operations are not normally carried out. This paper describes the factors affecting physical transport of matte into slag by gas bubbles, and the subsequent entrapment and flotation of matte drops. Three distinct patterns of transport behaviour have been identified from studies of a number of liquid/liquid systems, including liquid metal and liquid matte systems. A theoretical approach is proposed to explain these behaviour patterns, and to predict transport and entrapment behaviour in matte/slag systems. The concepts of "Film Coefficient" (ø) and "Flotation Coefficient" (?) are introduced. The effects of smelting process variables on the physical loss of copper matte in slag are also discussed.

Jan 1, 1972