Search Documents

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By Bill A. Hancock

In Situ leaching for the recovery of uranium from low grade sandstone deposits is one of the newest technological advances in the mineral industry. It is rapidly developing into a commercially feasible mining system which has economic, environmental, and social advantages over conventional mining systems. Because of the current uranium shortage, development of In Situ leaching into a sophisticated system has gained new impetus. In Situ leaching will become an important mining technique in the future, which will greatly help to supply uranium for our nation's energy heeds. In this paper, I will be giving an overview of the merits of the system, as well as the technology, problems, and research in solution mining of uranium.

Jan 1, 1977

By John F. Burst

For several generations now, the high alumina clayey sediments of Southeastern Alabama and Southwestern Georgia have supplied those regions with steady, mineral-based income although the impact of that income has been relatively minor until recently. Since World War II, mining activity has increased algebraically with over half of the total ore value in the Alabama area having been recovered since that time. The Georgia area production increases are even more dramatic. The trends are continuing and the next decade should see ore winning figures which will dwarf all previous production. It's time for the mining engineers to take note of this development as the mining methods, similar to the production, have developed rapidly and now offer challenges for the most competent professional. The development of mining techniques has followed a classic pattern. Beginning almost a hundred years or so ago, with the loading of weather-resistant surface boulders into mule-drawn wagons, mining methods have progressed to discovery of limited surface exposures in outcrop and eventually to stripping and development of non-obvious, subsurface deposits. Little by little, the overburden thickness of new pits has increased until, at present, pits with 100' -125' of overburden are being actively worked. Ground water problems in the Eufaula District are particularly challenging. At A. P. Green's J. W. Baker Pit, #l, in Barbour Co., Alabama, it is necessary to continually pump groundwater at the rate of about 400 gallons per minute from wells on the periphery of this large pit in order to keep the water table low enough to allow mining of the ore body.

Jan 1, 1972

By R. V. Ramani

This report is volume 10 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Ventilation subsystem of the Master Design Simulator. The Ventilation subsystem has the capabilities to handle: (1) branches in parallel or series, (2) fans in parallel or series, (3) multiple fans, (4) methane, compressed air, or other injections into the system, (5) leakages and fixed quantities, and (6) calculations of absolute pressure at nodes. The program uses the Kirchoff's Junction and mesh laws, and the Hardy-Cross iterative technique to converge to the desired accuracy in solving fox the head quantity. A case study is included in the report illustrating the use of the model. The appendices of the report constitute a user's manual for the Ventilation subsystem, and include a program listing.

Jan 1, 1975

By Harry W. Campbell

During 1983, the U.S. Bureau of Mines conducted a mineral survey of 19,700 acres that included the Fish Creek Mountains WSA (Wilderness Study Area), 15 miles southwest of the Salton Sea. Two United States Gypsum Co. claim groups in the WSA have more than .20 million tons of inferred gypsum reserves. These high-grade, surface and near-surface gypsum deposits are an extension of a gypsum bed that has been mined continuously since 1922. The Waters prospect in the central part of the WSA has large quantities of limestone suitable for many commercial uses. Sand and gravel is plentiful in the WSA in alluvial fan and ancient shore-line deposits. Limestone and alluvial deposits are not economic because similar material is closer to potential markets. No evidence of energy minerals or geothermal resources was identified in the WSA. A portion of the eastern Fish Creek Mountains WSA is leased for oil and gas exploration. United States Gypsum Co. holds eighteen unpatented placer claims in the northwestern part of the WSA. No other mining claims or mineral leases were identified in the study area. No mineral production is known from within the WSA.

Jan 1, 1986

By D. V. Hughes, J. R. Nyberg

"Since 1985, a comprehensive automation system has been installed at the Outokumpu Oy Zinc Plant, Kokkola, Finland. In leaching and solution purification special sample handling equipment, on-line analyzers and instruments, and a computer-based control system with duplicated supervisory stations have been installed. The system has enabled closer control of the process and more efficient use of labor. Since its installation recovery of zinc has improved, and use of zinc dust, steam, and water have decreased. The system has performed reliably. It includes optimizing programs and process study tools, which facilitate improving process performance. An expert system has been built-up to prompt process personnel to take appropriate action on the basis of process data. In electrolysis a similar system, based on extensive monitoring of the process and of production of zinc cathodes, is used to maximize- current efficiency by maintaining optimum conditions in the process. It is planned that in the future the control systems will be integrated and extended to cover the roasting plant and effluent control.IntroductionThe Zinc PlantThe Zinc Plant of Outokumpu Oy Metallurgical Division at Kokkola, on the West Coast of Finland, has grown from a 90,000 t/a plant founded in 1969 to become, with its present capacity of 170,000 t/a, one of the world's ten largest zinc plants. Especially since the completion in 1988 of a thorough modernization programme, it is also among the world's most modern.The Kokkola plant takes its raw materials from Outokumpu's own mines, Vihanti and Pyhasalmi in Finland, and Tara in Ireland, and from outside sources. Concentrates are roasted in two Lurgi fluid-bed furnaces, and the calcine is leached and iron removed by the Conversion process. Following this copper, cobalt, and cadmium are removed, and zinc is refined by electrowinning. The leaching and purification, and the cell-house are automated under computer-based control, and anode and cathode handling in the cell-house are mechanized and fully automatic."

Jan 1, 1989

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By W. W. Adams

With production of coal per man-hour of work highest in history, the coal mines of the United States established a lower accident-frequency4 rate in 1942 than in any year since 1930, the first for which the Bureau of Mines, United States Department of the Interior, collected complete reports of nonfatal as well as fatal injuries. Reports from mine operators and State mining departments showed that 530,861 men were employed in and about coal mines during the calendar year 1942. This number does not include office employees or coke-oven workers. The figure represents a decrease of 15,831 men from the previous year, owing to losses of men to the military services and to more lucrative employment in the munitions and other industries. The loss of men was offset to some degree by an increase in the number of days of mine activity and the average number of hours of work per man during the year. The volume of work done during 1942 was 910 million man-hours, 11 percent more than in 1941. The average employee worked 243 days, 30 days more than in 1941. Production reached the unprecedented total of 640 million short tons, an increase of 12 percent over 1941; 582 million tons came from the bituminous fields of the United States and 58 million tons from the anthracite fields of Pennsylvania. To produce this quantity of coal 1,471 men sacrified their lives, and 69,564 men suffered nonfatal injuries that disabled them for more than the remainder of the day on which the accident occurred. The nonfatal injuries were divided into three groups: 65 caused permanent total disability, 2,045 caused permanent partial disability, and 67,454 caused temporary disability of 1 day or more but did not result in the loss of, or permanent loss of use of, any part of the body.

Jan 1, 1944

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By B. Xu

Keywords: Magnetic damping, g-jitter, Hot-film anemometry Results from an experimental study on natural convection induced by temperature gradient in molten gallium contained inside a rectangular container. The damping effect of the convective flow from an externally applied static magnetic field is investigated. Induced velocity and temperature fields are mapped using a standard constant temperature hot-film anemometry and a thermocouple with and without the applied magnetic field, respectively. Detailed experimental setup and procedure are depicted in the present paper. Obtained velocity and temperature profiles are examined against previous numerical simulations and reasonably good agreement has been achieved. Obvious damping effect can be observed in both the temperature and the velocity profiles when the external magnetic field presents.

Jan 1, 2005

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By Baptiste Laubie

Agromining is a phytotechnology aiming at producing commercial metal compounds from low-grade ores thanks to hyperaccumulating plants. The fern Dichranopteris dichotoma is a rare earth element (REE) hyperaccumulator, which naturally grows on former mine tailings in China. It accumulates up to 0.35% of REEs in its aerial parts. Different hydrometallurgical processes are currently developed to recover these elements directly from the biomass or from ashes after combustion. The process presented here consists of a direct extraction by EDTA solution, followed by precipitation with acid oxalic. Optimal precipitation pH and influence of organic matter are determined by modelling and by experimental studies. The final solid contains 4.3% of REEs, with calcium as the main cationic impurity (0.45% of the precipitate). The recovery yield is similar for major REEs and is around 70%. After optimization, upscaling of the process will allow the agromining development to recover REEs from secondary resources with more environmentally friendly techniques.

By Songsong Wang

Recently, replacing Pierce-Smith converting process with the oxygen bottom-blowing continuous converting technology has become a new research focus. Based on the principle of Gibbs free energy minimization, the thermodynamic model of oxygen bottom-blowing continuous converting multiphase equilibrium system has been established. The elements distribution behavior is calculated at the same burden composition and operation parameters as the industrial production. The results show that the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in crude copper are 0.06, 0.0030, 0.070, 0.38, 0.39, 0.020, 0.017, 0.034, 0.010, respectively, and the absolute errors of the mass fraction (wt%) of Cu, Fe, S, Pb, Zn, As, Sb, Bi in slag are 0.53, 0.81, 0.020, 0.23, 2.5, 0.0048, 0.0010, 0.0030, 1.49, respectively. The calculated results agree well with the actual industrial production data, indicating that the model can be well applied in the oxygen bottom-blowing continuous converting practice.

By W. G. Prast

Best known for its extensive bauxite and alumina exports, Jamaica also has a small but active industrial minerals sector. The island has for many years been a net exporter of small tonnages of gypsum, metallurgical-grade limestone and marble products. As bauxite and alumina earnings have declined the government of Jamaica has made extra efforts to promote growth of overseas sales of these nonmetallics. The nearby U.S. market is a natural first choice for new exports. Overview In 1984, Jamaica quarried an estimated 3.2 million cu m of marble and fill and an additional 3.5 million cu m of sand and gravel, for use in domestic construction. These amounts are in line with the production in earlier years of the 1980s but are not a factor in the export pattern and need not be considered further. Similarly, annual production of 15 million ton of silica sand for the manufacture of glass bottles is principally consumed by the domestic market.

Jan 1, 1986

By M J. Nugus

The Geita gold mines in north-western Tanzania have produced 5 Moz of gold from an estimated endowment of 15 Moz. They are generally classified as typical Archaean orogenic banded iron formations (BIF)-hosted gold deposits in banded iron formations as described by Goldfarb, Groves and Gardoll (2001); Neall and Phillips (1987); Phillips and Powell (1993) and Neall (1987). The controls on gold mineralisation have been reassessed to conclude that Nyankanga, and we conclude that Nyankanga, the largest deposits within the group, developed during a dynamic and protracted deformation history intimately associated with several stages of hydrothermal fluid flow and alteration. The fluid-induced fractures associated with gold mineralisation are primarily manifested as submillimetre to metre-scale fractures and breccias developed preferentially in rocks that have been previously deformed and altered by silicification or seafloor metasomatism. This realisation detracts from the exploration and mining strategies that would solely concentrate on fluid pathways and associated wallrock alteration and veining solely within the BIFs as hosts for economic gold mineralisation.

Aug 22, 2011

By G J. Corbett, P Magner, M McKenzie

Structures formed during ductile deformation have been reactivated during the later brittle mineralisation process. Two generations of folding are classified as: early recumbent megascopic FI folds and FI shears which transpose the hinge regions, and later upright F2 folds. S1 is folded about F2 folds which contain axial planar S2 crenulation cleavage. Vergence relationships between S1 and bedding indicate that many of the mineralised structures occupy sites of FI folds which have acted as plumbing systems for later gold mineralisation (eg Blackwater mine). The Globe-Progress gold mineralisation is localised by a major jog formed by sinistral strike-slip movement on two FI fault segments and mineralisation also occurs in smaller jogs along strike (eg Sir Francis Drake, Happy Valley-Merrijigs, Cumberland).   The lodes of ribbon quartz which exploit the FI shears and local bedding planes, are inferred to have mostly formed after the peak of metamorphism, possibly related to the emplacement of Carboniferous granites. This was followed by a sequence of vein deposition and wallrock alteration which consists of quartz-As/Fe sulphides ? carbonate - stibnite ¦ trace base metal sulphides and Bi-sulphosalts ? illitic clay/sericite-chlorite. Gold at Globe-Progress is mainly encapsulated in arsenopyrite. At Blackwater, free high fineness gold occurs in partings in lode quartz with late sericite-chlorite. The above sequence of events is comparable to that encountered in many intrusion-related gold systems throughout the Southwest Pacific region. There is a spatial relationship between gold mineralisation and dykes variably described as diabase, dolerite or lamprophyre. Alkaline rocks occur in many Pacific rim and older goldfields and may possibly be related to a magmatic source for gold mineralisation.

Jan 1, 1997

By Thomas M. Barczak

This U.S. Bureau of Mines report examines the causes and consequences of longwall face sloughage. Theoretical relationships were developed to evaluate mechanisms that produce slough age. From these relationships, contributory factors were identified for further analysis in field efforts. A survey identified 12 mine sites with sloughage problems, and these were investigated. From these studies, it was determined that the depth of cover and mining height are the two most significant factors causing sloughage on longwall faces. Coalbed friability and cleat orientation also were found to be significant factors in promoting sloughage. It was concluded that sloughage is primarily a problem in thicker seams or seams with friable coalbeds, and that the problem is more severe as the depth of cover increases. Sloughage also was found to increase as the rate of mining decreased. Observations indicated that face slough age can increase dust generation significantly on longwall faces. Current efforts to control dust generation from longwall sloughage are described.

Jan 1, 2010

By W. T. Reid

A shortage of anthracite for home heating indicates the necessity of using other fuels for this purpose; low-volatile bituminous, or "soft" coal is the most feasible supplementary fuel, either burned alone or when mixed with anthracite. Comparison of Bituminous Coal and Anthracite Whereas anthracite is clean, burns without smoke, and requires little attention, bituminous coal is dusty, tends to burn with a smoky flame, and forms coke in the fire pot that must be broken up to maintain a continuous high output of heat. When properly fired, however, bituminous coal responds more quickly than anthracite to changes in damper settings and consequently can supply more heat in a short time. It is generally less expensive and usually contains less ash than anthracite.

Jan 1, 1943

By Alexander L. Peyton

The Magruder and Chambers copper deposits in the Little River gold district, on the border line of Lincoln and Wilkes Counties, Georgia, have been known for a number of years (fig. 1). The Magruder deposit was first opened as a gold mine but has produced mostly copper and load. Records show that about 50 cars of concentrates were shipped from this property. No record of any production at the Chambers deposit is available. The Bureau of Mines, in its program of investigation of strategic minerals deposits, diamond drilled 10 holes, totaling 3,784 feet, on the two properties between December 3, 1948, and June 23, 1949. Eighty-eight core samples were analyzed, and the analyses and drill-hole data are presented in this report.

Jan 1, 1950

By William G. Pariseau

The research reported here concerns ground control in multi-seam mining and relates mainly to the analysis of stress about multi-seam room and pillar mines. The two variables of most concern are distance between seams and alignment of pillars between seams. The first year results of the two year investigation apply to the development phase of mining when the extraction is typically less than 50 percent. The second year effort is concentrated on retreat mining and barrier pillar safety when the extraction is typically greater than 50%. The procedures in both cases are readily applicable to more than two seams. Although two seam mines are the most frequent type of multi-seam operations, because of the potential for three seam operations in the Western United States, a number of three seam development analyses are also presented. The results enable one to make a rapid assessment of stability of rooms and pillars during production and barrier pillar size during extraction of adjacent panels. In the event of low safety factors, more site-specific analyses can be undertaken.

Jan 1, 1983