Search Documents

During the past three years Lurgi's Circulating Fluid Bed (CFB) technology has been successfully applied to roasting of refractory gold ores and con- centrates. In comparison with the so-called Stationary Fluid Bed roasting systems, a considerable improvement of gold recovery, to around 95 per cent, has been demonstrated and achieved on many occasions in pilot CFB units and in commercial CFB roasting plants as well. The major reason for such improved gold recoveries is the excellent controllability of the roasting process in the CFB reactor system. Here, temperature, gas atmosphere and solids residence time are more precisely controllable at optimal values during roasting operation in order to achieve the highest possible gold recovery in the subsequent leaching process step. Further dominant benefits of CFB roasting systems are their flexibility with regard to feed material, throughput capacity, dry or slurry feed, almost unlimited oxygen enrichment, direct fuel addition and in situ capture of SO2 in the presence of limestone and dolomite. The system will accept 50 per cent turndown ratio, large variations in feed composition and particle size, as well as a variety of different fuel types. The commercial applications of CFB roasting systems for gold con- centrates have been realized so far at Fimiston, Kalgoorlie/Westem Australia and for whole ores at Cortez, Nevada/USA.

Jan 1, 1991

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

Total mechanisation in the Western district of New South Wales is quite a recent addition to productive methods in that State, for it was only in 1940 that the first colliery was equipped for this method of winning coal. Now almost all mines either are totally mechanised or are planning to get their coal by these means.This marked change in recent years is explained by the salient features of the industry's history. Collieries in New South Wales had generally been subjected to low selling prices forced on them by over-production and severe competition. Little money was available out of profits to purchase machinery, and returns on capital were so poor that inducement to invest money in the industry was nonexistent.The second world war brought price fixing at the already low prices. It was not until the post-war period that there has been any inducement to mechanise.Much credit for mechanisation can be given to the Joint Coal Board, a government body formed in 1948. Pursuing a broad plan for the rejuvenation of the industry, this Board, purchased large quantities of machinery for use in, mines under hire-purchase agreement. These agreements encouraged machine mining, and this fact, together with the ensuing production economies, has improved the financial position of the industry.The Board has also been instrumental in the granting of increases in the fixed price of coal, so that the industry has been given an even greater boost in the direction of mechanisation.

Jan 1, 1954

By A. S. Speirs

Over the last few years, the never-ending search for mineral wealth has taken the exploration efforts of Canadian mining companies further and further into the High Arctic and isolated locations where regularly scheduled transportation and communication facilities are nonexistent. Names such as Black Angel, Nanisivik, Asbestos Hill, New Quebec Raglan, Rabbit Lake, and Arvik are today frequently mentioned in mining publications. Twenty years ago, mining in these locations was unheard of, mainly due to logistic problems. However, improvements in the design and use of helicopters, STOL aircraft, and icebreakers in northern areas have helped to overcome these problems, making these locations more attractive to mining companies. Since 1969, when Redpath completed its first Arctic project at Texas Gulf's Scrathcona Sound property on the northern tip of Baffin Island, Redpath has been actively involved in contracting and engineering projects in three general areas: the High Arctic, Ungava and Greenland. A map showing some of these projects is shown in Figure 1. In these areas, permafrost conditions exist from a depth of 274 metres in Ungava to a depth of approximately 610 metres in the Little Cornwallis Island area, with rock temperatures ranging from -5°C to -13°C. Outside temperatures range from a low of -50°C in the winter to a high of 21°C in the summer. High winds in the winter result in wind chill factors lower than -73°C

Jan 1, 1980

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920&apos;s in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By Wijnand Dalmijn, Hans de Ruiter

Experience over the past eight years has proven that partnership and cooperation in mineral engineering education is essential to maintain programs in this field. At this moment the joint European Mineral Masters Engineering Course (EMMEC) has three programs in the areas of mining, minerals engineering and geotechnical/environmental engineering, offered by combinations of nine universities in seven European countries. About 25 companies are associated with the universities in the Federation of European Mineral Programs (FEMP) which coordinates these activities. The EMMEC has applied for recognition under the newly launched EU “Erasmus Mundus” program in which the EU makes 280 million Euro available for bursaries for non-European students and scholars.

Jan 1, 2005

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By Ron J. Elliott, Dylan Wedgewood

A series of five signature holes were blasted at the Highvale Mine and the resultant seismic data was analyzed to make recommendations on how best to address neighbour complaints regarding blast vibrations. From an analysis of peak vibration levels measured at the closest neighbour for blasting during 2016, it was determined that the blast vibration intensity varied between 1.4 to 4.3 mm/sec (0.06-0.17 ins./sec.), well below the level of concern for the onset of minor damage to residential structures, however, the frequency of the blast vibrations was between 2.2 and 9.7 Hz, which is within the range of the natural resonant frequency for a single story home. This was determined to be the cause of the neighbour complaints, as the home would be responding to the blast vibrations.

Jan 1, 2018

By Subrata Dutta

Sindesar Khurd Mine is situated in Rajasthan, India, and operated by Hindustan Zinc Ltd, under Vedanta Group. The base metal mine is high in reserves of Lead, Zinc and silver and has been producing since 2007 with initial production of 0.3 mtpa. Recently the mine has gained prominence as a base metal underground mine in introduction of latest mining techniques and achieving high production at lowest costs. The promising Lead-Zinc reserves of Sindesar Khurd Mine (SKM) and high-tech exploration adopted by Hindustan Zinc Ltd (HZL), (Vedanta Group), raising the reserves and resources from a meager 9 Mt (1997) to 81 Mt (2012), has prompted HZL management to ramp up the mine production from 0.3 mtpa (2006-07) to 2 mtpa by 2013-14 with ambitious plans to reach 3.5mtpa subsequently (presently largest underground metal mine in India). The complete trackless system underground mine, recently equipped with latest leaky feeder communication system (unique in India), utilize modern drilling, mucking and hauling equipment aided with various utility/service vehicles. Excavation optimization and quality recovery maximization from the open and post filled stoping methods, continual expert analysis and feedback from International consultants like AMC (Australia) and SRK (UK), and involvement of renowned bodies in management excellence, have lead the mine towards highest productivity and lowest mine operating cost, earning the mine a prominent place in the global base metal industry. The paper deals with how the various challenges in mine planning and designing, mine development, operator skill, equipment introduction and maintenance, expertise availability, provide training and exposure to officials, prompt and effective communication/service, control of ground vibrations, maintain ventilation standards etc are faced in attaining high operational excellence and thus attain a record mine output/man shift (OMS) of 14 ton/man shift with targets to reach 20 ton/man /shift. Scientific designing using 2D/3D numerical mine-modeling techniques, faster stope sequencing with introduction of paste filling ( first time in India),latest leaky feeder communication system, control ground vibration to stringent standards using electronic delay system, faster raising techniques using raise borers to enhance development and ventilation, cavity scanners to monitor large stope voids, fast shaft sinking at 100 m/month(Chinese expertise) and maintaining adequate ventilation with close software monitoring are some of the highlights discussed in the paper towards achieving the targets.

Aug 1, 2013

By James J. Kabat, James A. McDonald

Impregilo/SA Healy JV recently completed this Project using the first slurry shield TBM’s in the United States. The Project used two TBM’s to mine 18,000 feet in sands, gravels, and silty alluvial materials under the Willamette River and downtown Portland, Oregon. This paper discusses alignment and geological conditions, equipment selection and plant setup, and tunnel excavation means and methods, parameters, and results. Extensive hyperbaric operations were required and will also be discussed.

Jan 1, 2007

By Laura McNally

In 2006 McNally International Inc. in a Joint Venture partnership with Aecon Constructors was the successful bidder on two York Region Tunnel Projects: Bathurst Collector/Langstaff Trunk Sewers; and YDSS Interceptor Sewer 19th Avenue Project. These projects comprise a total of 13 kilometres of 2.74 meter finished diameter tunnels and are both part of the York Durham Sewer System (YDSS). Both contracts require the use of EPB tunnel boring machines with a precast concrete segmental liner. The following provides an overview the two projects.

Jan 1, 2008

By M. Haase

[ ] How important is a robust communications system for your mine site in order to meet operational and safety requirements? Do you currently have VSAT in place and need a low cost, high quality multi-line VoIP phone system at the site? By adding a single, compact piece of hardware, you can utilize your existing satellite internet connection and have as many as twenty-four separate phones lines from a single unit. The platform is scalable for any size of operation and can be implemented above or below ground.

Jan 1, 2012

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

By JIAQI JIN, Chen-Luh Lin, Amanda N. Erskine, Jan D. Miller, Shijie Wang

The liberation and exposure of valuable mineral grains in ore particles are of significant importance in understanding the efficiency of flotation separations. A flotation feed sample from the Kensington concentrator was scanned by micro Xray computed tomography (micro-XCT), to determine the liberation and exposure of auriferous pyrite grains. The analysis results suggest a satisfying extent of liberation for particle sizes smaller than 212 μm. Theoretical flotation recovery of pyrite for selected particle size fractions was predicted from the three-dimensional liberation and exposure analysis. The plant flotation tail was also characterized by micro-XCT to identify liberated and partially liberated pyrite particles that might not be collected into the concentrate. However, liberation analysis of the tail sample revealed that the majority of liberated pyrite was recovered in the plant flotation circuit. Trainable Weka, a machine learning segmentation approach, was compared with the Watershed thresholding segmentation for the 106 × 45 μm particle size fraction scanned at a voxel size of 1.85 μm. Improved segmentation of small particles was found using the machine learning method.

Mar 1, 2024

By A. S. Romaniuk

More than a decade ago, CANMET management recognized the need to make better use of existing technological information in mining and extractive metallurgy-two fields basic to the economic well-being of Canada. There were at that time no indexes or files dedicated to disseminating technical information for the many minerals mined and processed in Canada, including coal. CANMET, with the nation&apos;s largest research and library resources in the minerals field, was in a unique position to fill this need. Initial efforts were concentrated on building a mining file, beginning with identification of world sources of published information, development of a special thesaurus of terms for language control and adoption of a manual indexing/retrieval system. By early 1973, this file held 8,300 references, with source, abstract and keywords given for each reference. In mid-1973, operations were computerized. Software for indexing and retrieval by batch mode was written by CANMET staff to utilize the hardware facilities of EMR&apos;s Computer Science Centre. The resulting MINTEC file-one of the few files of technological information produced in Canada-is the basis for the national literature search service in mining offered by CANMET. Attention is now focussed on building a sister-file in extractive metallurgy using the system already developed. Published information sources have been identified and a thesaurus of terms is being compiled and tested. The software developed for CANMET&apos;s file-building operations has several features, including the selective dissemination of information and production from magnetic tape of photo ready copy for publication, as in a bi-monthly abstracts journal.

Jan 1, 1979

By Christopher Cloete Uys, Luis Manuel Poinha Valentim

The purpose of this workshop is to describe and demonstrate the use of SPEEDWAVE, a high speed data recorder, its VOD enhancements, and the software which binds the system together. The system was designed by TLC Sohware, SOUTH AFRICA. TLC is a company spedalising in the solution of engineering problems, using computertechnology as a base. TLC was founded in 1987, and has since been involved in many different.measurement, control, simulation and modelling projects. Wth respect to the blasting industry, TLC has, in conjunction with AECI South Africa/ICI, developed a tunnel mining design aid, a ring blasting design aid, a multkhannel seismograph and a laser surveying program. In 1989, TLC designed and built the BA800. a microcomputer-based high speed recorder. These recorders are still in use and are producing valuable results. Based on improved technology and with the field experience of the BA800, TLC has designed and developed the data recorder SPEEDWWE.

Jan 1, 1995

The plans involve about ten technical sessions, a day spent in Cripple Creek and in Pueblo, where there will he optional visits devoted to steel, non-ferrous metals, etc.; half-a-day each to mills in Colorado Springs district and an auto trip to the top of Pike&apos;s Peak. Finally, a day at Leadville devoted to visits, including the molybdenum works.

Jan 4, 1918