Search Documents

By Alfonso Rizo-Patrón

El presente trabajo describe la importancia de la explotación de los fosfatos de Sechura en la cuenca del Pacífico. Para ello, se evalúa el potencial de recursos naturales aprovechables en una infraestructura concentrada del área de Bavoyar y su implicancia en el aprovechamiento del potencial para el año 2000. Asimismo, es importante la planificación de un programa y una coordinación técnica adecuada de las realidades físicas, geográficas y geológicas de la cuenca señalada, así como la responsabilidad que ello implica.

Nov 20, 1972

By R. Balia

The upper part of the "Contatto Ovest" orebody, at the San Giovanni Pb-Zn sulphur mine (Sardinia, Italy), is mined by a sublevel caving method. With increasing mining depth, a progressive caving of the hanging wall and discontinuous subsidence occurs. The orebody, which is located very close to the contact between the Cambrian limestones and the Silurian shales, strikes NE-SW for more than 100 m and dips 75-80' NW. The limestone footwall is massive and strong while the hanging-wall consists of very weak shales. The mine considered is located near a town so that the observed subsidence effects must be taken into account for both stability of the nearby railway and houses and morphological and environmental impact. A limiting equilibrium analysis to predict the progress of hanging wall failure with increasing mining depth was used. A suitable computer program was developed for solving the model by a iterative procedure. The progressive hanging wall caving and its consequent superficial effects were predicted perfectly by means of the computer program used and later confirmed by a geophysical test (seismic tomography). Our study ends with a further analysis, carried out using the same procedure, which allows to have a different geometrical situation with the presence of a pillar to protect the mill area.

Jan 1, 1990

By Robert A. Cummings

A rock mass classification system has been developed for support estimation in mines using caving methods. The developed system (MBR System) accepts readily-obtainable geotechnical properties, and mining geometry, to develop a rating that permits recommendations for drift support in block caving mines. The data base includes major active United States caving mines. The method is intended to be used for planning and estimating purposes and for preliminary support design. The Manual explains the organization and nature of the MBR System, its derivations, details of required input data, methods for assessing the data and for developing rock mass ratings, and techniques for selecting the most appropriate mine support recognizing mine requirements and desired stability. A worked example is provided.

Jan 1, 1984

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By Mario E. Rossi

Often geometallurgical models are prepared at various project stages from very few data and are assumed to be representative of very large tonnages. These may include recovery models; crushing and grinding parameters and models; models of concentrate grades; models of acid consumption; etc. These models commonly do not carry a measure of uncertainty or variability, and are taken at face value at the time of design and planning. This paper proposes a proactive approach to modelling variability, providing uncertainty estimates and thus allowing for risk analysis and mitigation of geometallurgical models. The variability model is built up by understanding the limitations of the pillars of a geometallurgical model: data uncertainty; geologic model uncertainty; domain definition uncertainty; and parameter estimation uncertainty. Of these factors, typically domain definition is the most significant contributor to geometallurgical model variability. First, the fundamental supports for these models are briefly discussed, with domain definition emphasized. Second, two methods for uncertainty modelling are proposed. The first, more applicable to conceptual or early-stage projects, is a simpler and more expedient alternative that provides initial assessments of variability. This is intended to aid management in decision-making related to budgeting, including further sampling and testing. The second, a block-by-block approach that allows a detailed assessment of risk for specific designs and mine plans, thus providing further opportunities for mitigation. In the example provided, emphasis is placed in communicating this variability to both management and technical personnel in the form of “measured-indicated-inferred” indicators and also block-by-block confidence intervals.

Jun 25, 2023

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

By V. D. Perry

Carlisle: Reno, let's start off by asking "When was the first day that you began working in your profession?" Sales: I began in Butte, Montana, on August 22, 1900 as an assistant engineer for the Boston & Montana Consolidated Copper and Silver Mining Co., and continued at that job for about a year. The general manager was C. S. Batterman, and the mines- Mountain View, Pennsylvania, Leonard, East Colusa, and one or two others-were part of Boston & Montana.

Jan 5, 1966

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By J. Chia, M. H. Kobler, J. Cheung, M. J. Robison

INTRODUCTION The Lake Merced Transport is being constructed as part of San Francisco's Clean Water Program. The Clean Water Program, which began in the early 1970's, is designed to control wet weather, storm sewage overflows into the Pacific Ocean and San Francisco Bay. To accomplish this goal, a system of large underground storage and transport facilities, pump stations, modernized treatment plants, and outfalls is being built. By 1991, eighty percent of the system had been completed and was in operation. One of the remaining projects for the Clean Water Program is the Lake Merced Transport. The Lake Merced Transport is located in the extreme southwestern portion of San Francisco, as shown in Figure 1, Project Location. The transport will convey dry weather flow from the existing Lake Merced Pump Station to the Westside Pump Station. During wet weather, the transport will fill with sewage and runoff, with a storage capacity of 36 million liters. The Lake Merced Transport was expected to be excavated entirely within the Colma Formation, an alluvial deposit consisting of weakly cemented sand. Once excavation of the access portal at the Sloat/Great Highway parking lot began, it became evident that a portion of the tunnel would be excavated through beach/dune sand. Based upon the expectations of the Geotechnical Design Summary Report (GDSR), encountering beach/

Jan 1, 1993

By Jean Robitaille

La découverte du gisement du puits Penna a nécessité une révision complète de tous les circuits du concentrateur Laronde pour permettre, premièrement, l?adaptation du procédé à la nouvelle minéralogie et deuxièmement, l'accroissement du tonnage de 1800* à 4500 t/j. Aux circuits existants de broyage, de flottation du cuivre, de cyanuration et du charbon en pulpe, les circuits suivants furent greffés : broyage semi-autogène, flottation du zinc, manutention des concentrés (épaississage, filtration, entreposage et chargement automatisé), décantation à contrecourant et précipitation au zinc, destruction des cyanures et remblai en pâte. Cet article se veut une revue des différentes étapes du projet d'agrandissement du concentrateur qui se sont effectuées par phases progressives de 1997 à 2000. De plus, une description des nouvelles technologies sélectionnées et implantées est présentée.

May 1, 2001

Jan 1, 1997

Komatsu America has introduced its 2-MW (2,700-hp), 930E-3 ac electric drive truck with a 290-t(320-st) capacity. The truck is designed to provide increased productivity, lower cost per ton hauled and improved speed and control. The 930E-3 is powered by a Komatsu SSDA16Vl6016-cylinder engine. It is capable of speeds up to 65 km/h(40 mph) and is a 15-percent to 20-percent more productive unit than 218-t (240-st) trucks, at a lower operating cost per ton. The 930E-3 also provides enough torque and speed to get up and off ramps easier than mechanically driven trucks. And it can climb at altitudes up to 3,650 m(12,000 ft) without any fuel deration.

Jan 1, 2004

By Martin Stoklossa

Surface mining operations typically require run-of-mine material to be sized for further processing. In-pit crushing facilities serve this need, as stationary, semi-mobile or fully mobile units. Although in particular fully mobile crushing facilities have been in use for over half of a century, other surface mining techniques have typically been implemented. However, with increasing operating costs in truck and shovel operations, and other economic considerations, mobile crushing plants are increasingly a viable option. The operational and economical parameters in relation to the optimal surface mining equipment selection will be reviewed. The role of the mobile crushing technology within the continuous vs. noncontinuous surface mining operation and basis for mine planning are also discussed. Current applications and respective case studies will be reviewed. Key performance indicators will be presented. These performance parameters can be viewed as a tool to aid in the equipment selection process. The future direction for further research and development in mobile crushing facilities will also be presented.

May 1, 2008

By W. J. Kroll

Despite the fact that barium minerals are plentiful and widely distributed in nature, this element is one that we do not yet know how to prepare cheaply in metallic form. This is due to its chemical activity, as evidenced by its great affinity for fluorine, chlorine, oxygen, nitrogen, hydrogen, and sulfur. Furthermore, it forms a very stable subchloride and subfluoride, which prevents isolation of the metal by fusion electrolysis from a halide bath. A good survey of the metallurgy of barium calcium, arid strontium has been made recently in Light Metals (54,55).3/ Metallic magnesium (46), calcium (83), barium, and strontium (27) reduce each other's oxides. Proof of this can be found in the activation of BaO after reduction with Mg, which leads to the formation of so-called "Maquenne" mixtures (58) used for absorbing gases. However, it is impossible to extract the reduced metal- from the residue, a fact that Guntz (25) attributed to the formation of barium suboxide. There is no necessity for presuming the formation of such a compound, as it has boon established that in the reduction there is always formed an alloy of the alkaline-earth metal with the magnesium, which is capable of producing hydrogen when brought into contact with water. The reduction of alkaline earth-metal oxides with aluminum was observed by Mallet (57) in 1877, but recent investigations have shown that the end product of the reaction is an alloy of aluminum with the alkaline earth metal (1,2). Silicon also has been suggested as a reducing agent, and the results obtained are the same (84,85).

Jan 1, 1945

By S. K. Sharma, R. Markandeya, G. Venkateswara

"In this study, a three level Box- Behnken factorial design combined with Response surface methodology (RSM) for modeling of process parameters of Multi Gravity Separator (MGS) for recovery Iron values from sub grade iron ore, Deposit No. 5, Bailadila complex has been developed. The three significant operational parameters of MGS, Drum rotational speed (RPM), Drum inclination (degrees) and quantity of wash water (LPM) were considered in the experimental work. Other parameters like feed percent solids, shake frequency and shake amplitude were maintained constant. The ‘as received’ sub grade iron ore sample is admixture of lump and fines and chemically assayed 40.80% Fe, 40.90% SiO2, 0.24% Al2O3 and 0.22% Loss on Ignition (LOI). The obtained results were evaluated with the Box-Behnken factorial design, RSM and also Quadratic programming(QP). Second order response functions were produced for Fe in terms of grade (%) and recovery (%) of the concentrate fraction. Taking advantage of QP, it was observed that maximum grade of 62.21% Fe achieved at an inclination of 4.3degrees, 2.7LPM of wash water and at a drum speed of 198 RPM. Similarly a maximum Fe recovery of 65.37% weight can be achieved at 4.3degrees inclination, 2.6LPM wash water and at a rotational speed of 212 RPM Predicted values of responses obtained using model equations were in good agreement with the experimental values. The influence of the process variables of the multi gravity separator concentrator on grade and recovery of concentrate fraction were presented and discussed."

Jan 1, 2014

By P. K. Jain

A spiral concentrator is a density separation device used for the beneficiation of coal and various minerals such as iron ore, chromite ore, gold, beach sand minerals etc. The flow pattern developed in the equipment is complex and unique, yet the operation is very simple, with low capital and operating expenditure. Spirals are applied for beneficiation of material in the size range finer than 2 mm and are capable of recovering heavy minerals as fine as .01 mm. The understanding of the unique flow pattern has kept researchers engaged over the last few decades and attempts are being made to explain such flow patterns so that they can be controlled and modified to improve the operating efficiency, Ep (Ecart Probable Error, also known as probable error in separation) and acceptability of spiral concentrators for processing of fines and slimes - currently being discarded and dumped in the tailing ponds. An attempt has been made in this paper to explain the generation of complex flow patterns with application to classical solid mechanics in the fluid and slurry system. The same has been used to explain the selective separation of particles in different zones in a cross-section on the spiral trough. The paper also discusses the application of a force balance model to explain the generation of secondary circulation. Due to the presence of laminar and turbulent flow regimes in the spiral concentrator, varieties of equations have been proposed in the literature, consisting of different equations for different zones. An attempt has been made to present a unified flow equation for calculation of flow velocity at different positions on the spiral trough. Keywords: Secondary circulation, spiral concentrator, density separation, fine particle processing

Jan 1, 2020

By P. H. Francis

In This report, factors which currently enter into the design, manufacture, and quality assurance of explosion-proof enclosures are reviewed, with special emphasis given to the sealing concepts and sealants/cements, per se, for lenses. The physical and mechanical properties of a number of representative sealants and adhesives are measured, and found to exhibit great variance, with few discernible trends which might afford a firm base on which to establish minimum property standards. Accordingly, acceptance criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure rather than upon the minimum mat real properties of its constituents. Procedures or surface preparation of adherends, and for quality assurance, also are proposed.

Jan 1, 1980

By L. Gutierrez, J. S. Castro S. Laskowski

Water is a medium in which flotation takes place, and flotation efficiency is highly dependent on water quality. Of the total water resources on Earth, less than 2.5 percent is fresh water. This water is used in agriculture, by households and by industry. Among the industrial users of fresh water, the mining industry occupies an important position. Furthermore, mining operations are often located in arid areas with very limited access to fresh water. The demand for and shortage of water in these parts of the world, such as the Atacama Desert in Chile, makes the use of seawater by the mining industry the only sustainable solution. 

By Zengwu Zhao, Peng Xu, Jieliang Wang, Qingwei Bai, Xinyang Liu, Xiao Lei

The paper investigates the capture and recovery of rare earth minerals from Bayan Obo ore using superconducting magnetic separation. A finite element model (FEM) was established to study the influence of various factors on the capture of rare earth minerals under a high-gradient superconducting magnetic field. The study aims to improve the efficiency of rare earth mineral separation and recovery.

Oct 1, 2023

By Jacob L. Brinkman, Catherine E. Johnson

Researchers are exploring the use of unmanned aerial vehicles (UAV) to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect density-based concentrations as measured by some governing entities, including the Occupational Safety and Health Administration (OSHA).