Search Documents

By Steven J. Schatzel

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers.

Jan 1, 2009

By Laura Kelsey

Contaminant Robust In Situ Water Extractor CRIWE Nafion-based water clean-up Extract purified water from natural extraterrestrial sources In situ water processing for downstream electrolysis Chemically resistant to process contaminants such as acid

May 1, 2013

By Morgan M. Sears

In recent years, one large mine collapse and numerous smaller bump events have resulted in a renewed interest in coal bump research. With numerical modeling, the Energy Release Rate (ERR) calculation quantifies the ?release? of the gravitational potential energy of the rock mass into the environment as mining progresses. This release of energy can occur passively in the form of heat and sound or dynamically in the form of pillar bumps or rock bursts. From the initial application of a calculated energy release rate in the deep hard-rock mines of South Africa, the ERR was found to have a significant correlation with the risk or potential of damaging coal bumps or rock bursts. In this research, an ERR calculation is incorporated into the modern LaModel program to facilitate the analysis for potential coal bumps. Initially the ERR calculations in LaModel are verified using a case study of cut sequences originally modeled using the MULSIM/NL program. Then, the ERR calculations are applied to a bump-prone mine in Southern Appalachia were a number of different pillar recovery cut sequences were used in order to minimize the risk of bumps.

Jan 1, 2009

By I M. Platten, Y Xie

Sampling protocols that are designed to suit the mineralisation style will result in a reduction of the nugget effect and hence resource risk. The a priori need for all sampling programs is the effective characterisation of the mineralisation type(s) to support optimisation. This requires a program of sampling for sampling followed by holistic characterisation. At each end of the coarse-gold to fine-gold spectrum, the samplability of a deposit ranges from relatively simple for fine-grained disseminated gold particles, through to extremely difficult for coarse nuggety mineralisation. Many deposits contain a proportion of both particle size types. The proportion and size of coarse gold particles has a direct impact on the effectiveness of sampling, where coarser particles will require larger samples and more specialised protocols. The nature of mineralisation geology/mineralogy and associated gold particle sizing can only be determined by sampling to facilitate optimised protocols. Mineralogical studies, focusing on particle size, particle clustering and distribution in host minerals, are required as part of wider paragenetic and metallurgical investigations. This paper discusses the role of mineralogical studies in the characterisation of gold ores for sampling optimisation through a series of case studies.

Jan 1, 2008

By R. R. Trengove

This paper is one of a series published by the Bureau of Mines on mining methods and operation practices. It describes the open-pit mining method and operations of the Kaiser Steel Corp. Eagle Mountain iron-ore mine, which is in the extreme southeastern part of California 175 miles east of Los Angeles in Riverside County. Nearest town to the mine is Indio, which is 60 miles away by an excellent highway (fig. 1). Elevations at the deposit vary from 1,400 to 3,000 feet. Figure 2 is a plan map of the Eagle Mountain iron mine. Kaiser Steel Corp. built a model camp at the mine, with all modern conveniences (fig. 3). The camp, comprising 145 homes, dormitories, mess hall, commissary, post office, and recreational facilities for 600 people, is at 1,390-foot elevation. The area has winter-resort weather between October and May, with occasional drops of temperature to 25° at night. From June to September temperatures sometimes rise to 1200 during the day. Rainfall is scant, approximately 2 inches a year, the majority of which comes as cloudbursts during the summer months.

Jan 1, 1956

By Pedro Vargas Gálvez

El presente texto señala la metodología de selección del software de mantenimiento respecto a este mismo y a la Planta. Para ello, se detalla las condiciones que deberán considerarse en la Organización de Mantenimiento y la aplicación del Software de Mantenimiento MP2 a una empresa. Asimismo, se presenta el Plan de Implantación, los inconvenientes que se han encontrado así como los resultados obtenidos por la utilización del Software MP2.

May 25, 1998

By Sherwin F. Kelly

THE geophysical scene shifts and alters, the emphasis changes, and new possibilities loom, but the tendency is always towards widening the field and deepening the analytical penetration. Seismic methods have had their heyday, the torsion balance is being displaced by the gravimeter, electrical methods are showing deeper penetration, soil analysis is the newest tool, and gamma-ray logging appears on the horizon. One of the striking features of re- cent geophysical work in the oil fields has been the marked decrease in the number of seismic crews employed. Although the percentage of company crews is believed to have increased appreciably. the sum total has fallen sharply, as shown by the figures for the Gulf Coast area. About two years ago probably over 100 seismic parties were operating there, whereas now there are only about 35. This decrease may be partly due to the low prices of petroleum with a consequent reluctance to spend money to increase crude-oil re- serves but more probably to the fact that reflection and refraction shooting have been carried on so extensively that they have been applied to a large pro- portion of the areas in which they may reasonably be expected to succeed. Some of the earlier enthusiasm, particularly over reflection prospecting, may have erred on the side of over- optimism; some of the present curtailment may be due to over pessimism; but in the opinion of various observers seismic work at the present rate seems to be at it- optimum. It nevertheless remains pre-eminent as a technique for detailing structures in areas where good reflections can be obtained and is the only method that will give accurate depth to definite beds. Results may be poor in certain areas but many regions still remain wherein it can be applied, so that plenty of structural mapping remains to be done by the reflection seismic method.

Jan 1, 1940

The object of this paper is to give an insight into various metallurgical operations involved in the making and shaping of steel for shipbuilding at the Newcastle plants of the Broken Hill Proprietary Co. Ltd., Commonwealth Steel Co. Ltd. and the Port Kembla plant of Australian Iron and Steel Ltd. Whilst not steelmakers, inasmuch as their processes start with semi-finished. steel supplied by the Steelmaker, the plants of Stewarts and Lloyds (Aust.) Pty. Ltd. and their associate company, British Tube Mills, Rylands Bros. (Aust.) Pty. Ltd. and the Newcastle and Kembla plants of John Lysaghts (Aust.) Pty. Ltd. make substantial contributions to the Australian shipbuilding industry, principally by way of boiler tubing and wires for welding rods and sheet steel, including special silicon lamination sheet for electrical motors.THE MAKING OF STEELThe making of iron and steel began as an accident, slowly developed as an art and has not yet become an exact science. The iron age dawned on the day when, by chance, man's primitive ancestor built up the wall of his fire with ironstone. In the ashes of the fire he found pieces of sponge iron from which he hammered out the first sample' of wrought iron. For many centuries iron ·was manufactured in bloomeries and occasionally, when the temperature was excessive, the iron combined with some carbon and steel was produced. But it was not till '1740 that steel was manufactured under controlled conditions. In that year Huntsman invented the crucible process which held undisputed sway for over a 100 years until in 1856 the invention of the Bessemer process revolutionised the whole industry.From then on, rapid progress was made. The Siemens...

Jan 1, 1951

Possibilities and Working of the Specific Agglomeration of Fibrous Materials and Residues Plant based fibrous materials are becoming of increasing interest in a multitude of industrial applications. Main advantages are the specific lower energy demand and virtually closed CO2 cycle, excellent mechanical properties based on low density as well as a high level of recyclables. In contrast, processing and handling of such materials is associated with a number of challenges. These challenges are mainly related to specific morphological characteristics in correlation to fibre length and structure (branching and splices). Specific problems in further processing steps including transport, dosage or storage for natural fibre compounding, result from form-locking bonds leading to burling, clusters or plaits. Technologies of fibre processing are well known, but other than textile based technologies they generally result in intermediate goods which do not allow direct industrial application. The investigation to be presented is based on results of recent research activities and shows two possible technical solutions of innovative fibre agglomeration procedures. These methods allow the conversion of middle to long fibres into a form, which eases further processing and dosage significantly and therefore allows free flowing too. The procedures are based on the working principles of rolling and winding technology. Within the work, both of the patented methods and their respected lab-scaled devices will be described. Further, results will be shown for an up-scaled rolling agglomeration unit applying the developed principle and consisting of multiple process zones. Possible variations of the resulting product characteristics and the impact of different process parameters will be discussed based on the trials with natural fibre (hemp and flax) agglomeration. As a main outcome of the research, product qualities can be supplied according to the requirements of the specific application in correlation to agglomerate strength, porosity or form. In conclusion, recent developments for specific methods of characterization will be depicted.

Sep 13, 2010

By John B. Knaebel

This paper is one of a series being prepared by the Bureau of Mines on mining methods and costs at various mines in the United States, Canada, and Mexico, and is a description of practice at the Edwards mine of the St. Joseph Lead Co. ACKNOWLEDGMENTS The cooperation and assistance of the officials of the St. Joseph Lead Co. in permitting publication of this paper and providing every facility for its preparation are gratefully acknowledged. Especial thanks are extended R. J. Mechin, manager, R. F. Mitchell, mine captain, and J. S. Brown, geologist, for their generous aid, and the assistance of W. H, Weijola, mine engineer in assembling some of the illustrations is deeply appreciated, The helpful suggestions of C. F. Jackson, principal mining engineer, U. S. Bureau of Mines, are gratefully acknowledged.

Jan 1, 1932

By Muriel S. Robinette

Ground-water contamination from uranium operations could be avoided with proper site analysis techniques. Contamination from tailings disposal sites is carried downgradient within permeable hydrostratigraphic units which can be located and delineated with a combination of drill holes, borehole geophysical logs and surface geophysics. Several case studies are presented to illustrate this application.

Jan 1, 1980

By William Eathorne

"INTRODUCTION Retsof mine, adjoining the village of Retsof, Livingston County, New York, is about 5 miles northwest of Geneseo and 55 miles (air-line distance) due east of Buffalo. It is a single-bed rock-salt mine having extensive horizontal workings as much as 2-1/2 miles long and 1 mile wide and has been in continuous operation since 1885. Retsof tine is the largest producing salt mine in North America and is reputed to be the largest active salt mine in the world.Retsof is one of three large salt mines operated by the International Salt Co., Scranton, Pa.; T. Forster Courthope is general manager of Retsof and also of the company's Detroit salt mine in Michigan and has held that position for 27 years. He is assisted by Stanley Martin, general superintendent; R. Goetz, Maintenance superintendent; and John Riordan, mine superin¬tendent. All are old-timers at Retsof and, according to Courthope, contri¬buted the ""lion's share in bringing the mine to its present standard of safety.ACKNOWLEDGEMENTThis circular was made possible by the generous cooperation of T. Forster Courthope and his assistants, Stanley Martin, R. Goetz, and John Riordan. The information and time generously given are gratefully acknowledged.GENERAL INFORMATIONThe rock salt as mined contains about 99 percent sodium chloride and requires only crushing and screening to prepare it for the market. With the exception of a large jaw crusher underground, all crushing is done in a mill building attached to the headframe of the main hoisting shaft (fig. 1).Five sizes of salt are produced, ranging from about 1/2 inch diameter down to minus seven mesh."

Sep 1, 1949

By Thomas Fraser

"INTRODUCTION The Santa River Valley of northern Peru contains extensive deposits of a good-grade anthracite that offer one of the most accessible sources of solid-fuel supply for South America. This region is served by the narrow-gage railroad of the Corporation Peruana del Santa, which taps the coal fields along the Chuquicara River and terminates at the port of Chimbote, where facilities have been provided for loading coal into ocean-going vessels.This Government-sponsored corporation is prosecuting a vigorous program of development in this region, envisaging an intensively industrialized area around Chimbot Bay, fueled and powered by the anthracite of the upper valley and a hydroelectric generating plant now being constructed in the Cahn del Fate, where the Santa River has cut through the coastal range of the Andes.This development also includes the construction of extensive irrigation works to greatly expand agricultural production in the valley and thus estab¬lish the basis for a prosperous, well-balanced, industrial and agricultural community. It is hardly necessary to point out the importance of the local anthracite-mining industry to this general plan.At the invitation of the Peruvian Government, through the agency of David Dasso, chairman of Corpoacion Peruana del Santa, a technical mission was sent to Peru in March, April, and May 1945 to examine these coals and assist the corporation in promoting preparation of the coal for most effective use in the contemplated expansion of industry and trade."

Feb 1, 1948

By Jeffrey S. Newman

This report presents a summary of the results of a four-phase program conducted for the Bureau of Mines to evaluate underground mine fire detection systems. In addition, Phase IV is presented in detail. The major accomplishments of this program are: 1) quantification and prediction of the distribution of fire products in a mine pas¬sageway; 2) quantification of "equivalent protection" by fire detectors as contained in Title 30 of the Code of Federal Regulations; 3) definition of detection criteria; 4) design of a detector test program for determining detector spacing requirements; 5) design, construction, operation, and calibration of a fire test apparatus for evaluating mine fire detectors; 6) quantification of several mine fire sources; 7) evaluation of several fire detector types including heat, CO and CO2 gas, and ionization smoke detectors; 8) development of generalized spacing criteria for mine fire detectors; and 9) development of performance specifications. Reports for Phases I through III are included in Appendices.

Jan 1, 1984

By J. G. EVANS

It is with a certain amount of trepidation that a man considers gathering his family of six, traveling across a continent, two oceans and a sea, and going to live in a foreign land. But "pioneering" is still possible, and a nation is "foreign" only until one has lived in it. We've had eight years of pleasant experiences in South Africa on which to base that contention. It was in January 1938 that my brother first extolled the virtues of South Africa to us, and just three months and a thousand small problems later my wife, two daughters, three sons and I were boarding a ship in New York, bound for Cape- town. We arrived in May, and within a week had found a furnished home with beautiful lawns, tennis, court, a garden, and everything needed for family comfort. The children were soon located in school, and I settled down to the task of entering the importing business, as had been my original intention. The importing business started out slowly but was coming along nicely when on Sept. 3, 1939 the war started in Europe and a declaration of war by the Union of South Africa was made on the following day. With the declaration came import and export controls. In fact we were controlled completely out of business in one stroke. Liquidating the business, I went to Johannesburg intending to find work in one of the mines. Government health and safety regulations require that all underground mine employees have a red ticket from the Miners Phthisis Bureau certifying that they are not susceptible to silicosis, the scourge of the Witwatersrand gold mining industry. I made application to the Bureau, completed a form covering my whole past life, and was given a complete physical examination. The following day I was startled to find that I had not only been refused a red ticket but had been classified with a green ticket which for- ever bars one from working underground in any scheduled mine in the country, and all this in spite

Jan 1, 1949

By J G Bastias

It is sometimes necessary to resort to extremes in order to call attention to something that is pertinent to safety in mining. When some of the experts in occupational safety talk about this topic, they usually refer to a 'regulation' established by the Romans which stated that, due to the health hazards, usually death, no Romans but only slaves should work in mining. Since the time of the Roman Empire, a lot of ground has been covered in the field of mine safety. Nowadays, it can be said that occupational safety is being seriously addressed, with the result that the number of mining accidents has reduced dramatically, fatalities in this industry are less frequent, and the rate of accidents compared with other activities, such as construction or fanning, is low. This achievement has been possible initially through government legislation and by procedures established by the mining companies themselves. However, the dilemma for government is whether to regulate and if so, how much. It is pleasing to observe that most companies are establishing working procedures which conform with new government legislation, placing strong emphasis on the duty of care for mine employees. There will always be some regulatory aspects of legislation, and perhaps the best example of this is in the use of mine hoists where there are no international or Australian standards, and the regulations applied are of an empirical nature that err on the side of safety.

Jan 1, 1994

By Renato G. Bautista

The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions:. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.

Jan 1, 1996

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By A. F. Baker

Tests were conducted in commercial foundries to determine the suitability of calcined anthracite as a cupola fuel. The calcined anthracite performed satisfactorily at two of the three foundries where iron-melting tests were conducted. Performance at the third installation was unsatisfactory because metal temperatures deviated widely and, in general, were lower than is desirable for the type of castings being made.

Jan 1, 1963

By R. L. Christie

"THE ISLANDS lying north of the Canadian mainland, and the large Boothia and Melville peninsulas, form one of the great archipelagos of the world; this sparsely vegetated and nearly unpeopled region extends about 1,500 miles east to west and 1,200 miles from the mainland to the northern tip of the northern-most island. Sea access to most of the islands is restricted by ice to the summer season, and the 'polar pack' ice of the Arctic Ocean presses the year round against the northwest margin of the archipelago. Although the region is remote, the accessibility has greatly increased through a network of weather stations, airfields and air routes connecting with southern centres.The area considered in this paper is that part of the island region underlain mainly by sedimentary rocks. In broad terms, this includes the land and sea areas of the archipelago and the adjacent continental shelf, but excludes the dominantly 'Shield' terrain of Baffin Island, and of Melville and Boothia peninsulas. An impression of the size and potential of this sedimentary region may be gained by comparing some areas: the land area of islands underlain mainly by sedimentary rocks is over 300,000 square miles or about 50,000 square miles greater than the area of Alberta. The total area of the region, including the continental shelf and the inter-island areas, may be double this figure, and may approximate one-seventh of the land area of Canada."

Jan 1, 1970