Search Documents

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

By F. Elgersma

Hydrometallurgical zinc winning processes ?are frequently based on iron containing concentrates which yield a goethite, jarosite or hematite residue. Jarosite or goethite are mostly stored in waste ponds which ,are lined with foil. Water percolating through the pond is withdrawn from the deposit ,and decontaminated before discharge. Despite these measures, more and more pressure is put upon zinc companies to treat their (historical) residues and to produce environmentally acceptable residues. The criterion which determines this acceptability is the potentiality of leaching out hazardous elements by natural processes. This paper provides the comparison of five different process designs for integrated jarosite treatment in a hydrometallurgical zinc winning plant leading to environmentally acceptable residues. The processes are esigned for producing 200 ktons/yr zinc and for treating 80 ktonslyr historical jarosite. Mass and energy balances are used to determme parameters such as: the energy use per ton waste treated and the amount and composition of final residues. The conclusion of the work is that. pyrometallurgical jarosite treatment integrated in hydrometallurgical zinc winning is preferable to hydrometallurgical jarosite treatment. Integrated pyrometallurgical processes lead to a ?smaller quantity of remaining hazardous residues and require less energy.

Jan 1, 1992

By D Obeng, D Alexander

Over the past five years, commodity prices have been high and the focus of many plants has been æthe more metal the better, at whatever costÆ. In the recent economic crisis, the focus has shifted more to reducing the cost of production and operating at higher efficiency. Since 2002, JKTech has partnered with the Century mine in north-west Queensland to transfer technology and understanding through the good, bad and ugly economic environments, using methodology and techniques arising from research at the Julius Kruttschnitt Mineral Research Centre (JKMRC) and other research institutions around the world as part of the AMIRA International P9 Project. The JKTech studies were concentrated around the primary zinc circuit. During this period, Century expanded the primary zinc regrind capacity, installed additional scavenging capacity, installed and commissioned a Jameson cell for concentrate cleaning in the carbon preflotation circuit, and installed additional primary grinding capacity. Flotation circuit models were developed for each of the survey campaigns and enabled opportunities for further improvement to be identified, implemented and tested in the subsequent campaign.

Jan 1, 2009

By Tell Ertl

An annual invitational address by an outstanding man in mining, geology, or geophysics who has contributed significantly to the progress of technology in these fields. IN 1954, the first year the award was conferred, Fred Searles, Jr., remarked, "The earlier years are the easiest." In this, the second year, it was easy to choose the outstanding mining engineer. Our conferee this year has been destined to mine. He comes from pioneer stock, and though a son of the American Revolution he is most proud that all four of his grandparents came to the Jordan River Valley of Utah the "first summer," which all Utahns will recognize as 1847. At the time of discovery of high-grade ore in Bingham, his grandfather, Archibald Gardner, had a crew of men getting out saw timber in the area. The first claim staked in Bingham Canyon was named the Jordan, and Bishop Gardner was the colocator of the claim as well as the man to record it. E. D. Gardner was born in West Jordan, Utah, in view of Little Cottonwood Canyon, the site of the Emma Mine. Park City in the Wasatch Mountains a few dozen miles to the east, and Tintic, not much further to the south, were developing their vast ore-bodies throughout his youth. As a boy he was near the present Midvale metallurgical area and could see the Lark and Bingham Canyon mine dumps and imagine the mining activities at Tooele, Ophir, and Mercur just over the nearby Oquirrh Range. He was 11 years old when the first car of copper ore was shipped from Bingham Canyon. It was not surprising that he attended the University of Utah and graduated with an engineer of mines degree. Five years with the Utah Apex in Bingham Canyon as chief engineer and assistant superintendent completed his training for the 44 years of unselfish and lightly rewarded service he was to give the mining industry as a Government engineer. All of us in mining are familiar with the great work he carried on and directed during the genera- tion he supervised the Southwest Experimental Station at Tucson. He has written scores of papers and books. His observations and experiments on drilling and blasting have led to the important improvements in this field during the past quarter century. Whereas those of us who consider ourselves widely informed about underground metal mining methods make hasty trips through a half dozen or dozen mines a year, our conferee has visited them all—not only the metal mines, but also coal and hundreds of nonmetallic mines, in the United States, Canada, Latin America, and overseas. His keen observations and analytical mind have resulted in an encyclopedic knowledge of mining and mines. His improvements in mining technology have been steady and predictable. His elucidation of mining problems to the many young engineers that have come under his guidance have made them grow strong and useful to his industry. When he chooses to stop, his influence will continue to expand and prosper because of the inspiration and dedication he instilled in so many of us. The profits from his ideas have been distributed throughout the mining industry. He has remained a technical man who felt that he could serve the mining industry best as a Government engineer. But he is the staunchest advocate of the belief that the public should gain from his work through private industry. This is not the first recognition E. D. Gardner has received. The Department of the Interior awarded him the coveted Medal for Distinguished Service in October 1949, and he received the Engineering & Mining Journal's Salute in March 1951. His friends who are presenting him the Daniel C. Jackling Award today know this great mining engineer simply as "Ed" Gardner.

Jan 1, 1956

By Lis Nunes Soares

A qualidade de fabricação de tubos de aço sem costura está relacionada ao processo de tratamento térmico. O controle do comportamento dos fornos industriais de tratamento térmico é de grande importância de modo a garantir a qualidade do produto. É necessário conhecer os parâmetros de operação dos fornos, assim como suas influências nas variáveis de processo. Este estudo avaliou as extensões do efeito do tipo de alinhamento dos tubos no interior do forno nas temperaturas dos canais de fumaça, temperatura do forno, temperatura do tubo, pressão interna do forno, demanda dos queimadores e consumo de gás natural. Diferentes alinhamentos podem impactar no escoamento da massa de gás queimado dentro do forno e consequentemente ter um efeito nas variáveis de processo avaliadas. Para determinar o tipo de alinhamento mais adequado do ponto de vista da qualidade do material final e da melhor eficiência energética, testes foram realizados durante uma corrida em um forno de austenização, na qual se alternou entre os diferentes tipos de alinhamento, medindo-se as variáveis de processo estudadas. Os resultados foram analisados utilizando-se técnicas estatísticas, como ANOVA. Ao final observou-se que certos parâmetros são impactados pelo tipo de alinhamento do tubo, sobretudo a temperatura de fumos e pressão interna no forno. As variações foram relativamente pequenas, principalmente pelo fato da principal variável controladora do processo, a temperatura do forno, possuir uma dinâmica de resposta lenta.

Jul 31, 2018

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

By Cheng Wei

Fly-ash was used as adsorbent to remove butyl xanthate from aqueous solution in this study. Adsorption kinetics investigation reveals that the adsorption process abides by the Lagergren-second-order Kinetic Model, and fine fly-ash prepared by grinding has a higher second-order adsorption rate as 1.25 g/mg?min and a higher saturated adsorption amount as 10.92mg/g. Four influencing factors as adsorption temperature, solution pH, consumption of fly-ash and adsorption time were investigated. Testing results indicate that butyl xanthate removal rates declines slightly with the temperature increase within the range of 15-50?, increases slightly when pH rises from 7.27 to 8.01 and then declines from 99.65% to 98.25% when pH rises from 8.01 to 11.10. An enhancement of removal rates can be observed by increasing the consumption of the adsorbing agent or prolonging the adsorption time. Thermal desorption was adopted to regenerate the used fly-ash, and test results show that fly-ash possess good regeneration performance and could be used as adsorbent repeatedly with little influence on the adsorption capacity.

Sep 1, 2012

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By Hsin Wei Wu

A real-time Diesel Particulate Matter (DPM) monitor has been developed on the basis of the successful National Institute of Occupational Health and Safety (NIOSH) designed Personal Dust Monitor (PDM) unit. The objectives of a recently completed Australian Coal Association Research Program (ACARP) study were to modify the PDM to measure the submicrometre fraction of the aerosol in a real-time monitoring underground instrument. Mine testing focused on use of the monitor in engineering evaluations to determine how conditions can be improved. Studies, including a selection during Longwall (LW) moves as described in this paper, demonstrated how DPM concentrations from vehicles fluctuate under varying ventilation and operational conditions. Correlation between the current SKC DPM measurement system and real-time DPM monitors were conducted and results from six mines show a correlation between elemental carbon (EC) and the new monitor DPM mass ranging from .51 to .81 with R2 >.90. These differences are suspected to be due to variations from mine to mine in aspects such as mine atmospheric contamination, vehicle fleet variations, fuel type, engine maintenance, engine combustion efficiency, engine behaviour or interference from other submicrometre aerosol. Real-time monitoring readily reflects the movement of individual diesel vehicles and allows pin-pointing of high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. DPM monitoring approaches that have been available for some time based on shift average monitoring do not readily allow successful engineering evaluation exercises to determine acceptability of pollution levels. Identification of high DPM concentration zones allows efficient modification of mine ventilation, operator positioning and other work practices t o reduce miners? exposures without waiting for laboratory analysis results.

Jan 1, 2010

By W. G. Huang

To recover the coal resources of high-sulphur anthracite in Jincheng Mining Area, underground coal gasification (UCG) of No. 15 seam in Fenghuangshan Coal Mine was proposed. The feasibility of the project was confirmed by investigations of occurrence conditions, coal properties, and roof conditions, as well as experimental studies and theoretical analysis. It was found that UCG technology is appropriate to be adopted in the mining of the No. 15 seam, due to the stable rock conditions, simple geological structure and hydrogeology, the high carbon content of the coal, non-cohesiveness, medium-thermal stability, high ash fusion temperature, and weak reactivity with CO2. Further factors are the characteristics of the immediate roof, which consists of 9.11 m of limestone and mudstone with a compact structure and low permeability, and 4.27 m of dominantly mudstone with low permeability.

Jan 1, 2012

By Michael Taylor, Thomas W. BoBo

Currently two of the most important characteristics of construction aggregates are (a) the particle size distribution (psd) and (b) the “shape” of the aggregate particles. The long established test methods and standards for these properties require substantial resources and most suppliers can take samples and conduct tests at intervals measured in days (psd) or even months (shape). Furthermore these tests require time: so the results are available only after material has been stockpiled or shipped. In the rare cases where problems are found the out-of-spec material has often been shipped to points unknown. There are substantial advantages to be obtained if the psd and other geometrical properties could be obtained from the material as it moves through the production processes and if the results could be reported back within seconds or minutes to Plant Control Managers. This paper describes a single on-line system used to evaluate production of crushed material in a production quarry. The system consists of an enclosure (containing the camera and lighting etc.) mounted over a production belt. Images are fed by fiber optic cable to a nearby control room where the data are analyzed; stored; displayed; and made available for integration into a process control system. Numerous forms of display can be created according to the needs of the producer. Once programmed by an automation engineer all functions of operation are fully automated. The system has permitted over 400 tests per hour with a feed back time less than 2 seconds. Sufficient geometrical measurements are made so that many different “shape” factors can be computed on a similar time scale. The paper summarizes the results from approximately 100 shifts of about 8 hours each and compares the imaging method with the current standard hand methods. Study of the data generated showed that, when combined with additional plant information, the system can be used to generate additional useful control information.

Jan 1, 2005

By Yannis Faitakis, Simon Bergeron

"This paper describes the implementation of model-based predictive control (MPC) on a vacuum heat exchange network at Alcan's Jonquière Complex. The plant produces alumina from bauxite ore using the Bayer Process.The MPC system was commissioned in 2000, by Alcan personnel and an Advanced Control Engineer from Matrikon. The application has achieved an uptime of about 97%.The benefits were:• Energy savings : 0.5% - live steam reduction• Reduced variation: standard deviation of key temperatures reduced by 50%• Plant throughput increase: via the automated use of surge tanks• Decreased supervision time: by plant operations• Faster and easier diagnosis of problems and plant constraintsThe benefits were higher than expected with a payback time around 12 months.The purpose of the vacuum heat exchange network is to recover energy from a hot stream (pregnant liquor) by transferring it to a cold stream (spent liquor). The system is very tightly coupled, and the main constraints of the multivariable control system are: • to control the many tank levels involved in the process (8 tanks)• to maximize the temperature of the heated streams (spent liquor)• to prevent cooled streams (pregnant liquor) from cooling to below a minimum temperatureThe system includes 9 manipulated, 14 controlled and 2 feedforward variables.The advanced control implementation runs under an expert system environment and provides added flexibility to the overall control strategy."

Jan 1, 2003

By D. van der Veen

Mining companies and contractors are looking at Wirtgen Surface Miners to provide flexibility at their operations. Wirtgen Surface Miners have been used in the surface mining industry for over fifteen years. The principle behind the Wirtgen Miner is a rotating drum equipped with tungsten carbide tipped cutting tools that excavates and sizes the material. The drum helix augurs the mined material to the center of the drum where it is loaded onto the primary conveyor belt. From there the material is conveyed to the discharge belt and into a truck bed. The cutting drum is located in the center of the machine, near the center of gravity. This permits the machine to cut hard materials as the entire machine weight is converted into cutting forces. Conventional mining practices are process, equipment, and labor intensive. Furthermore, strict environmental requirements pertaining to noise levels, dust pollution, and blasting, near buildings or urban areas, limit the application of conventional methods. Mining/ Construction contractors are using Wirtgen Miners in various limestone excavation projects, such as highway expansion projects, and new roads in housing developments. Mining companies in the industrial minerals and coal industry are using Wirtgen Miners to load directly onto trucks, eliminating the rehandling process and ultimately, primary crushers.

Jan 1, 2002

Pictured on these pages are the seven RMCMI Scholarship Award Winners for the 1992-93 year followed by a brief profile. All winners were present as guests of the Institute at the June convention in Beaver Creek, Colorado to receive recognition at the Institute Awards Luncheon Monday, June 28. 1993. Each state vice president served as the host for the collegiate winner. In addition to receiving a plaque from the Scholarship Chairman, Alan Czarnowsky, each winner receives $750 tuition credit for the coming academic year. As this is a continuing award, the winners from the previous year will receive another $750 for tuition credit in their senior year if they have maintained good academic standing and are recommended by their university. A resident from each of the eight RMCMI member states is selected from among Board approved institutions. Criteria for these awards to be made in the spring annually is (1) That the award be made to a sophomore student and used as tuition during the junior year. (2) That the recipient be both a U.S. citizen and a resident of the member state. (3) That the recipient have good academic standing, be pursing a degree in a mining related field and have an expressed interest in Western coal as a possible career path. The scholarship program includes curricula other than those in the mining departments, but in engineering disciplines, such as geology, mineral processing and metallurgy. Contributions to this worthy project are tax deductible to each individual RMCMI member or his firm. Through annual donations of $100 or more, the Patrons of the Institute fund the scholarship pro- gram and the various vice presidents contribute the travel expenses to convention for these outstanding young collegiates. Donations to this worthwhile program may be made payable to RMCMI Scholarship and mailed to the RMCMI Office, 3000 Youngfield Street, Suite 324, Lakewood, CO 80215. Profiles of the 1993 Scholarship Winners follow. [ ] ARIZONA WINNER Kevin Shirley University of Arizona Tucson, Arizona A member of the Student Chapter - Society of Mining Engineers, Mr. Shirley also belongs to the Campus Crusade for Christ organization. He enjoys baseball, basketball and football. He states, "Miners are meeting the demand of the public by providing energy fuels and minerals to support the standard of living we enjoy. It is sad to see people out of work in this country, but the third world is largely undeveloped, and many jobs are moving abroad." 'I consider winning the RMCMI scholar- ship a great motivator; your belief in me will help me become my best." [ ] COLORADO WINNER Derek Rawson Colorado School of Mines Golden, Colorado "1 have been enthusiastic about the mining industry since I lived in Divide, Colorado and spent time exploring the old mine sites." Derek says. "President Clinton may hit the mineral industry with many reforms, but I believe self sufficiency is important ... we need to produce here in the U.S. what we consume." Mr. Rawson is involved with intramural sports and varsity track. He is a member of the Society for Mining, and Exploration, Inc.; Colorado School of Mines Caving Club; Colorado School of Mines Shooting Club; and Alpha Tau Omega Leadership Fraternity.

Jan 1, 1993

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By Ehsan Moosavi, Kamyar Tolouei

In open-pit mines, the long-term production scheduling optimization problem (LTPSOP) is a complicated problem that contains constraints, large datasets and uncertainties. Due to its dimensions and NP-hard nature, it is usually difficult to find an ideal solution to the LTPSOP. The optimal schedule generally restricts the ore, metal and waste tonnages, average grades, and cash flows of each period. In this paper, to synthesize grade uncertainty into the strategic schedule, a stochastic integer programming (SIP) framework is presented to LTPSOP. The objective function of the SIP model is to maximize the net present value and minimize the risk of deviation from the production targets considering grade uncertainty simultaneously while satisfying all technical constraints and operational requirements. Instead of applying one estimated orebody model as input to optimize the production schedule, a set of equally probable orebody realizations is applied to synthesize grade uncertainty in the strategic schedule and produce a more profitable and riskbased production schedule. To solve the LTPSOP, the hybrid approach with the augmented Lagrangian relaxation method, the Harris Hawks optimization, the Random Forest method and Monte Carlo method was proposed. To indicate the applicability of the model, a case study on a gold mine was implemented. The framework displays the capability to minimize risk and improvement in the expected net present value and financial profitability .

Jun 25, 2023

By Kathleen M. Kowalski

This research explores the emergence of leadership in a crisis situation. The study by the U.S. Bureau of Mines focuses on three underground mine fires and the resulting evacuations. The subjects for this study are 48 coal miners, who evacuated the mines as part of eight escape groups, The subjects described their escape during an open-ended interview. Data were coded according to: (a) evidence of leadership behavior, (b) evidence of lack of leadership behavior, and (c) characteristics of the individual in each group who led the subjects out of the mine. During analyses, attributes of the leaders, who facilitated the escapes, were noted and compared as were instances of lack of leadership. The structure of the group leadership before the crisis was compared with the reality of the leadership during the crisis. Some groups experienced an apparent breakdown of leadership during their escape, while others witnessed the emergence of leadership. Consensus characteristics of the leaders, who emerged during these crises, are discussed and generalizations drawn. Research into leadership during emergency escapes is needed to provide information for training in prevention, escape, and rescue. The authors suggest questions for further investigation and topics for further inquiry into the area of leadership evolvement during crisis.

Jan 1, 1994

By A Mcquillan, N Bar

Geotechnical models developed during the open pit mine planning stage are generally three-dimensional (3D) in component to capture the spatial variation in geological, structural, hydrogeological and geomechanical conditions. Yet when geotechnical analysis is completed, often the 3D geological, hydrogeological and structural models are simplified to two-dimensions (2D). This paper demonstrates this simplification, through referenced case studies, can lead to the wrong failure mechanism being analysed and/or a conservative Factor of Safety (FOS), or Strength Reduction Factor (SRF), being calculated, leading to a false sense of stability. There exists a paradigm that the FOS calculated using 2D limit equilibrium (LE), or the Strength Reduction Factor (SRF) calculated using 2D finite element (FE), modelling methods is generally conservative, ie lower, than the true FOS. However, this assumption that 3D FOS, or 3D SRF, is always higher than 2D FOS, or 2D SRF, is not always correct (Chen and Chameau, 1983; Bromhead and Martin, 2004; Herza et al, 2017; Pyke, 2017; Dana et al, 2018).

Nov 29, 2022

By William B. Hughes

The rubber-sleeve core barrel was developed to improve core recovery from unconsolidated sands, where it is most difficult to obtain cores with conventional barrels. The use of a rubber-sleeve core retainer, together with other departures from clsual design, has required a considerable amount of testing to prove its op-erability. Tests run in shallow experimental holes and in drilling wells in the U. S. and Vemzuela have, to a large extent, proved the operation of the barrel. Internal mechanism troubles, such as sandbinding of the sleeve, have been largely overcome. Cores have been recovered from completely unconsolidated sands where conventional coring has almost been abandoned because of poor recovery. In addition to retaining the core until brought to the surface, the barrel gives a "packaged-ar-cut" core, which is coilverzient for handling and transportatiorz. In the initial work, drag blade cutters, roller cutters, and tungsten carbide insert cutters were usrd for cutting unconsolidated sands. Further bit head development is presently being conducted using diamond heads in unconsolidated sands where shaler, hard sands, and limestones are encountered in adjacent formations. Thir work should render the barrel capable of cratting and recovering most types of formations, possibly including broken and frac- tured fornlations. This development is being carried on in cooperation with a diamond bit manufacturer. INTRODUCTIO N For many years the oil industry has needed greater recovery of cores from unconsolidated formations. Conventional equipment has been used to core unconsolidated sands with little success. Specifically, a core barrel was needed which would recover unconsolidated sands in a condition that would give useful reservoir information. DEVELOPMENT OF 'THE RUBBER-SLEEVE CORE BARREL Basic Requirements of Unconsolidated Sand Corino The basic need was defined as a core barrel that would obtain a continuous unconsolidated core with sand grains in place as deposited in the formation. A preliminary survey of coring equipment and search of the literature pointed out the weaknesses of conventional core barrels. Laboratory tests using unconsolidated sand in a metal tube simulated actual sand movement into the core barrel during conventional coring. In conventional barrels the core sometimes crumbles and bridges, or fails under compressive column action, becomes oversize, and wedges against the walls of the inner barrel. The core barrel requirements established by the surveys and preliminary tests are as follows. 1. The core should be held to- gether as it is cut so it cannot crumble and bridge against the walls of the coring tool, care being taken not to permit damage from fluid circulation. 2. The core should be continuously supported as it is cut so it will not have to support itself in compression. 3. The core should be packaged in the barrel to retain an undisturbed condition during the trip out of the well. The packaging should be such that the core can be removed from the barrel and shipped to the core analysis laboratory without physical disturbance or alteration of fluid content by exposure to the atmosphere. Operation of the Rubber-Sleeve Core Barrel The rubber-sleeve core barrel (Fig. 1) meets the basic requirements for the recovery of unconsolidated sands.

By H. Maleki

In this paper, long-term measurements in five underground mines are presented to demonstrate how these measurements can be applied to stability evaluations and design of underground excavations. These case studies address both the global aspects of strata response to mining activities as well local ground behavior and support loading. The measurements include static (stress and deformation) and geophysical. Case studies quantify pillar behavior, roof-floor deformation patterns, overburden response, and microseismic activities. Large-scale studies quantify the nonuniform nature of overburden deformation and collapse. Local measurements address yield and stable pillar load deformation characteristics, as well as the performance of support systems under combined axial and lateral loads.

Jan 1, 2002