Search Documents

By K. C. Mills, R. Thackray

A test has been devised that can predict accurately the % crystallinity developed in a slag film formed between the steel strand and the mould. The % crystallinity in the test samples was determined and compared with that for slag films formed in the mould when casting with that flux. There was good agreement between the % crystallinity in the test samples and the slag films. It was found that additions of TiO2and ZrO2had little effect on the amount of crystalline phase formed, but additions of CaO caused a dramatic increase in the amount of crystalline phase formed. Various parameters (which can be calculated from chemical composition of the flux) have been plotted against % crystallinty in the test samples. It was found that the modified (NBO/T) ratio provided the best relation with % crystallinity for the various parameters tested. There commended relation is % crystallinity=141.1(NBO/T)-284.0. Keywords: continuous casting, mould flux, slag film, crystallinity, chemical composition

Jan 1, 2004

By T. Lindstad, S. Gaal, S. Hansen, S. Prytz

The SINTEF SiO-reactivity test, developed by Tuset and Raaness in the 1970?s, is a recognised method of characterising the ?reactivity? of carbonaceous reactants, used in the ferrosilicon and silicon metal industries. Recently, the test has been updated, which has resulted in the development of an extended and improved SINTEF SiO reactivity test. This has included updating the test reactor, control system, data-logging, handling and preparation of carbonaceous materials to be tested and measurement procedure. The scientific basis has been re-assessed, resulting in a new interpretation of the test results. The repeatability of the test has improved significantly, especially through system automation. In the ?old? test, the kinetics of the reaction: SiO(g) + 2C(s) = SiC(s) + CO(g) for a specific carbonaceous material was characterised solely by the ?R10? parameter, the volume of SiO(g) which passes un-reacted through the coke-bed as the concentration of CO in the outlet gas decreases from 18 to 10%. As both the kinetics and obtainable conversion of SiO to SiC for a reductant is of importance to the ferroalloy producer, the new SINTEF SiO reactivity test ranks carbon materials both according to degree of conversion and reaction rate. From research carried out on the test in the past couple of years at SINTEF and NTNU, it has also become clear that some of the reactions taking place in the test reactor are more complex than previously assumed. As an example, it was previously assumed that the condensation reaction of SiO gas in the condensation chamber of the test reactor can be described as: 2 SiO(g) = Si(l,s) + SiO2(s). However, it has been established that the side-reaction: CO(g) + 2Si(l) = SiC(s) + SiO(g) causes approximately 10% of the total volume of CO to react to SiC and SiO2 in the condensation chamber. This means that some back-reaction i.e., the reverse SiO-generator reaction 3SiO(g) + CO(g) = 2SiO2 + SiC also takes place in the condensation chamber. In the new SINTEF test, the %CO versus time curves are therefore corrected in order to describe the effect of the reaction between SiO(g) and C(s) studied i.e., SiO(g) + 2C(s) = SiC(s) + CO(g). A correction-formula for this purpose is presented.

Jan 1, 2007

With some notable exceptions, marine placers located just below, or just above, present sea level, are responsible for much of today's production of detrital ilmenite, rutile, zircon, and other minerals of value. The purpose of this paper is to discuss the paleogeographic and paleo-oceanographic factors which may have determined the location of presently submerged marine placers. These factors include changes in sea level, burial by recent marine sediments, stream capture and other changes in drainage patterns, and recent changes in climate. Selected geologic situations in the Yellow Sea off the coast of Korea, in the Atlantic Ocean off the coast of Portugal, in the Bering Sea off the coast of Alaska, and in the Arabian Sea off the coast of India, will be used to illustrate the author's point of view.

Jan 1, 1971

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

By Huw Williams

"Power companies are always looking to increase the carrying capacity of existing transmission lines, and the preferred method is to string heavier capacity conductor lines. However this results in higher wind loading and the potential for towers overturning, if the existing foundations do not have the tensile capacity. On older lines, there is often a lack of information on construction type and dimensions and in practice the as-built foundation can differ considerably from design drawings, due to unforeseen ground conditions along the line route, and no record of the resulting change in design being made.Following successful trials in New Zealand, integrity testing with Frequency Response and impedance profiling techniques is now being used in the region to check concrete foundation properties in-situ and are enabling power companies to get the most out of their assets. INTRODUCTIONIn most regions of the globe, the US included, there is generally a requirement to upgrade transmission line capacities, to cope with increasing power consumption. Problems with under capacity only come to light for the public when blackouts occur, even in developed countries.A large number of transmission line towers are designed with a certain capacity redundancy and will be able to carry greater loads than originally designed for. Power companies are therefore looking for ways to assess their assets and to minimize the costs of upgrade work.Re-assessment of tower foundation capacities using design drawings may not be valid , as constructed foundations may differ considerably from design drawings, to accommodate local difficulties and in some instanced, particularly with earlier lines, there is no information whatsoever. This complicates efforts to determine the capacity of foundations considerably."

Jan 1, 2005

Over recent years the trend in Australia has been towards the definitions of sustainable development which emerged from the 1992 Rio Summit of retaining a commitment to ecological integrity, but also incorporating social and economic dimensions of sustainability. Sustainable development may be seen as maintaining and enhancing:natural capital: defined as all natural resources, both environmental and those of traditional economic value; manufactured capital: made by human kind; including produced goods, infrastructure and built environment; human capital: defined as the health, well-being, intellectual capabilities and spiritual welfare of individuals; and social capital: defined as social relations and institutions within and between societies, their norms and functionality (Ameef, 2002). This paper will endeavour to assess the challenges and opportunities facing the professionals and their Institute in the minerals industry in Australia because the MMSD Global and Regional Australia Reports do not, in the authorÆs opinion, adequately address the æhuman capitalÆ input into the current or future development of the minerals industry, in particular, the sustainability of the professionalsÆ skills, knowledge and experiences in a global context.

Jan 1, 2002

By A. J. Barry

Five makes of expansion-type shells and two types of bolts (mild-steel and high-strength) were used in 30 tests made in sandstone and shale roof, The results show that the anchorage obtained in both the sandstone and shale were stronger than either type of bolt. That is, the yield loads of both bolt types were exceeded before excessive anchor slip occurred. A relationship for evaluating the anchorage effectiveness of 3/8-inch-diameter, expansion-type bolts is presented. A comparison of test results indicates that the anchorage effectiveness of 5/8-inch- and 3/4-inch-diameter expansion-type bolts did not differ appreciably.

Jan 1, 1957

By Grant R. Brown

The objective of this paper is to describe a study sponsored by the U.S. Department of Energy during which a model was developed to optimize haulback mining procedures in single and multiple seam contour mines, The study objective was to achieve financial- based productivity increases approaching twenty percent. This paper reviews the results of the first year's Phase I activities, which include four main tasks: formulate a methodology that can be used to select equipment and mining procedures that result in optimal performance in a particular haulback mining situation; conduct field studies of representative single and multiple seam mines to obtain quantitative background information for development of the formulated methodology: develop the methodology into a useful design tool for mine operators; and prepare plans for field tests to evaluate the effectiveness of the developed tool.

Jan 1, 1981

By Tassos Grammatikopoulos, Vladimiros Papangelakis, Douglass Duffy, Cheryl Washer, Srinath Garg

Flotation operations in Sudbury, Ontario, seeking to separate pentlandite and chalcopyrite from mixed sulphide deposits, produce pyrrhotite tailings that have been disposed of in tailings ponds for over 50 years. These reactive tailings are viewed as waste, despite containing ~0.8 wt% Ni, and represent an environmental liability because of their acid mine drainage (AMD) potential. Given the large quantities of pyrrhotite currently stored in Sudbury, and declining ore grades elsewhere, these tailings have shifted from being viewed as a waste to a potential resource. Recent advances in the bioleaching of low-grade sulphide ores have raised the prospect of bioleaching as a potential low-cost processing option. However optimization of this proposed process requires a thorough understanding of the mineralogy of the pyrrhotite tailings that would be leached. The work presented here addresses the characterization of two distinct Sudbury pyrrhotite tailings, namely from the Vale and Glencore operations, using electron microprobe, XRD and QEMSCAN analysis. Particular focus is given to how the mineralogy may affect bioleaching as a processing option, through the deportment of nickel and the various phases present

Jan 1, 2015

By Alex Grenoble, Alex Reeb, George Filz, Farzad Abedzadeh

"This paper summarizes available information on the characteristics and properties of deep-mixed soilcement produced by the wet method. The topics covered in this paper include: unit weight, unconfined compressive strength, strength variability for field mixed materials, influence of curing time, influence of consolidation pressure, Young’s modulus, differences in strength and stiffness between small and large samples, creep deformations, Poisson’s ratio, and tensile strength. In addition, this paper discusses the development of design considerations and recommended property values for a project that uses soilcement to protect an existing dam penstock from loads applied by an overlying stability berm. Some of the key recommendations for the deep-mixed soil-cement to be used in this project are that (1) a curved strength envelope that includes tensile strength can be used in the analysis, (2) the stress-strain and strength properties can be characterized using Duncan and Chang's (1970) hyperbolic model, and (3) a specification based on the median unconfined compressive strength value is appropriate.INTRODUCTIONFor many projects, including foundation and embankment support, deep mixing can be designed based on simplified procedures and following standardized guidelines (e.g., FHWA 2013). However for unusually complex or critical projects, it is often necessary to perform numerical analyses, and in order to perform these numerical analyses well, a thorough understanding of the material properties is needed.This paper summarizes information on the characteristics and properties of deep-mixed soil-cement produced by the wet method, and it discusses the development of design considerations and recommended property values for a specific project, herein referred to as the penstock project, that requires numerical analyses. For the penstock project, a horseshoe-shaped enclosure of soil-cement is being considered beside and above an existing dam penstock to protect it from loads applied by an overlying stability berm that will be constructed for seismic remediation. The concept is to use soilcement created by the deep mixing method along the sides of the penstock and to use compacted soilcement above the deep mixing to create the crown of the protective soil-cement zone around the penstock. For this application, the soil-cement stiffness, rather than its strength, is the controlling design parameter. To achieve the necessary soil-cement stiffness, the strength will be high enough that the factor-of-safety values against instability along potential failure surfaces passing through the soil-cement are high. Following conventional practice, the soil-cement acceptance criteria will be based on the unconfined compressive strength, and the specified strength will be selected to produce the desired modulus value."

Jan 1, 2015

By C. Sahyoun

The influence of microwave treatment on copper flotation has been investigated. Comparative batch flotation tests carried out on ore treated at 5?12 kW for 0.1?0.5 s showed that improvements in copper recovery of between 6?15 % could be achieved compared with untreated ore. Both recovery and cumulative grade increased with increasing treatment time and power. A preliminary economic analysis showed that microwave treatment will be economically viable if recoveries similar to those determined on laboratory scale can be achieved on a plant. Keywords: microwave treatment, copper ore, flotation, liberation, recovery

Jan 1, 2005

By J. Böhlke, B. Friedrich, E. Hecker

The legislation for the disposal of heavy metals contaminated substances is still going to be tightened up in the future. The main criteria for the utilization or deposition of these residues are the content and the water solubility of these metals. Through this, the use of slags from the lead-and zinc-industry in road building may become limited or even not possible at all. From an economic point of view this would lead to Pb/Zn losses and costs for safe dumping. This paper investigates the feeding of the reducing agent via hollow electrode DC smelting and the yield of metal reduction. After carrying out thermodynamic calculations, the process window conditions for electric-arc furnace tests were determined. Doing this, the zinc could be reduced, evaporated and recovered as an oxidic intermediate product flue dust, while the lead was present either in flue dust or in metallic form. The zinc content in the final slag could be reduced by up to 90%. The slag product has undergone an eluation test which allows it to be used as building materials. Keywords: zinc reduction, lead reduction, hollow electrode, slag treatment, electric arc furnace

By Onwukamike, Onyedika G. O, Ogwuegbu M. O. C., K., Onyenehide C

A detailed mineralogical and elemental characterization of a lead (Pb) ore deposit from Ishiagu, Ebonyi State, Nigeria was carried out with XRD, SEM-EDX, and ICP-OES based mappingtechniques. The results show that the most dominant and valuable metal is lead (Pb = 95.02%, mass fraction). The main mineral is galena. Ilmenite and sphalerite occur as minors, which account for 2.71% and 0.80% respectively. Elements like Al, Ca, Mg, Ti, Na, Mn, Si and Sn occurred in trace amounts and are disseminated in the entire ore body.The surface and interrelations of the crystals were examined with x-ray mapping and the result shows the pattern of dissemination of the minerals within the ore body.

Jan 1, 2015

By Alizeibek Saleimen Nader

The intensive use of computers for mineral application at Serrana's phosphate mine in Jacupiranga, State of Sao Paulo, Brazil, began in the late seventies. The early hardware and software available are described in sufficient detail to allow comparisons between that solution and the new one, based on a personal computer and a new software package - PC MINE SYSTEM from GEMCOM SERVICES INC - that provides full color graphics capabilities plus mine design and planning tools. The process needed for adaptation to the new technology' and its impact on SERRANA S.A. DE MINERACAO are described. Finally, future enhancements to the System and mine control and planning are focused.

Jan 1, 1989

In recent years there have been significant advances in computing power and programming technology, enabling more complicated processes to be modelled in greater detail. This has led to increased understanding of these complex processes, including mineral processing circuits. JKSimMet was developed over the past 35 years, incorporating outcomes from various research projects conducted at the Julius Kruttschnitt Mineral Research Centre (JKMRC), part of the Sustainable Minerals Institute at The University of Queensland. It is a steady-state software program that allows the user to mass balance, model fit and simulate crushing, grinding and classification circuits. JKSimFloat has been developed over the past 20 years, incorporating outcomes from the JKMRC and other institutions around the world through the AMIRA International P9 project ? The Optimisation and Simulation of Mineral Processing Circuits. It is also a steady-state software program, similar to JKSimMet, but is focused on analysing flotation circuits. Both programs have been used in a wide variety of optimisation and design projects over many years. This paper provides an overview of both JKSimMet and JKSimFloat and examples of how both programs have been used to better understand, develop and optimise mineral processing circuits around the world.

Feb 27, 2013

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By A. Andrews

Paper written on project work carried out in partial fulfilment of MSc (Eng) degree Solid state sintered silicon carbide ceramics are used in aggressive environments as sealings. There exist data concerning corrosion, but there are only few data concerning their electrocorrosion behaviour. Therefore the electrochemical corrosion of solid state sintered silicon carbide (SSiC) ceramics has been studied at room temperature in acidic and alkaline environments by using potentiodynamic polarization measurements. The investigation showed a pronounced electrochemical corrosion in bases and acids. In HCl andHNO3pseudo-passivity features due to the formation of a thin layer of SiO2on the surface were observed, whereas in NaOH soluble silicate ions were observed, resulting in more pronounced corrosion. The microstructural observations of initial and corroded samples reveal that the residual carbon found in the microstructure do not dissolve preferentially. Keywords: Corrosion; SEM; SSiC; polarization test.

Jan 1, 2006

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means of controlling gases and dust. In order to study longwall ventilation in a controlled environment, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers built a unique physical model called the longwall instrumented aerodynamic model (LIAM). The LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel. It has an 8.94 by 4.88 m (29 by 16 ft) footprint with a simulated face length of 220 m (720 ft) in full scale. LIAM is built with critical details of the face, gob and mining machinery, and scaled to preserve the physical and dynamic similitude. This paper discusses the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By Bing W. Jong

A bench-scale evaluation of coal and coal waste materials as aggregate materials for use in longwall mine supports was undertaken as part of the Bureau of Mines Health and Safety program on ground control. Performance data were obtained on portland cement concretes (PCC) prepared with coal and coal wastes as aggregate materials. The effects of high-early-strength accelerators on strength and creep and of superplasticizers on strength properties of PCC formulated with coal and coal waste were investigated. Concrete formulated with a high-early-strength accelerator and coal and coal waste has 20 and 40 pet greater compressive strength, respectively, than the control samples without admixture. A concrete formulated with coal waste and the high-early-strength accelerator, using four bags of cement per cubic yard and a water-cement ratio of 1.0, had the lowest creep value of all the coal- and coal-waste-formulated PCC's tested.

Jan 1, 1983