Search Documents

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By Nik Sokol, Mike Jaeger, Leo C. Weiman-Benitez

Silicon Valley Clean Water signed a progressive-design-build (PDB) contract with Barnard Bessac Joint Venture (BBJV) to design and construct the Gravity Pipeline tunnel in Redwood City, CA. Owner and Design-Builder teamed with designer Arup to provide a final product: 3.3 miles of 182 in. O.D. precast concrete segmentally lined tunnel with 10 ft. and 11 ft. I.D. Fiberglass Reinforced Polymer Mortar (FRPM) carrier pipe, complete with two FRPM Drop Structures. BBJV and Arup collaborated with SVCW to evaluate alternative design concepts, negotiate an agreeable price and reduce contingencies through a transparent estimating process, and deliver the project ahead of schedule.

Jun 13, 2023

By Walter I. Paniagua

A housing complex of 76 buildings is being constructed in the city of Morelia, in western central Mexico; the buildings are 5 levels high, with a shallow concrete slab foundation. Soil conditions include a soft clay stratum, with up to 8 m depth, in a highly seismic area. Pile foundations and micro-piles were considered, but discarded due to economic factors. The alternative of soil improvement with rigid inclusions was used. An FEM (Finite Element Method) analysis was conducted to determine the diameter, spacing, length and arrangement of the inclusions. Construction was implemented with traditional methods: soil boring, and mortar tremied with pipe and the aid of a sock to contain the material (no steel reinforcement was used). So far, 46 buildings have been built, and level measurements for 18 buildings have been recorded since 2006, with resulting good behavior in both total and differential settlements.

Jan 1, 2008

By Kenneth C. Stewart

The overall purpose of this study was to develop and evaluate, in the laboratory, instrumentation and procedures which might allow for the use of physical measurements of earmuff attenuation which would yield results equivalent to those obtained from psychophysical measures of attenuation. The ultimate goal was to evaluate techniques which might subsequently prove feasible for physical measurement of earmuff attenuation in the field. Current instruments were modified to have a response similar to differrences observed in earmuff attenuation as observed in Volume 1 of the current contract. Mining noise spectra were selected and presented to a single subject seated in a diffuse noise field. The subject wore one of the muffs evaluated in the earlier study and was also fitted with two physical sound measurement systems. A linear system measured the "outside" noise level and a linear system plus "correction" filter measured the "in-side" noise level. These measurements indicated that, under the procedures presented in this report, a laboratory method for measuring earmuff attenuation is feasible and yields results comparable to an extensive psycho-physical procedure.

Jan 1, 1980

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By Francisco Gallo Atard

El presente texto señala los dispositivos promocionales vigentes respecto de los decretos leyes de minería, así como se analiza los problemas legales y tributariosque limitan el desarrollo minero tales como: indeterminación de leyes dictadas, normas negativas, falta de respeto a las normas dictadas, carencias de reglamentaciones y ausencia de criterios técnicos. Asimismo, se revisa la comercialización, comunidad minera, importaciones, productividad y los derivados de geografía y orografía.

Mar 1, 1979

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"The U.S. National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. RAs typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The U.S. Mine Safety and Health Administration requires that these valves vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer, above mine atmospheric pressure in the RA. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: (1) a modified polyvinyl chloride check valve, (2) an off-the-shelf brass/cast-iron butterfly check valve and (3) a commercially available valve that was designed specifically for one manufacturer’s steel prefabricated RAs and had been adapted for use in one mine operator’s built-in-place RA. PRVs used in tent-style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with Title 30 Code of Federal Regulations, or 30 CFR, regulations. The commercially available relief valve did not meet the 30 CFR relief pressure specification but may meet the manufacturer’s specification. Alternative valve designs were modified to meet the 30 CFR relief pressure specification, but all valve designs will need further design research to examine survivability in the event of a 103 kPa (15.0 psi) impulse overpressure during a disaster. BackgroundThe Mine Improvement and New Emergency Response Act of 2006, known as the Miner Act (U.S. Department of Labor, 2006), was enacted in the wake of three mine accidents involving explosions or fire that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the Miner Act includes provisions that target mine safety issues in areas such as emergency response planning; adoption of new technology; training and education; and mine safety standards enforcement. Section 13 of the Miner Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines, and the U.S. Department of Labor to act on the results of such research, as appropriate. These mandates culminated in the 2009 adoption of changes to the Title 30 Code of Federal Regulations, or 30 CFR, mining health and safety regulations (U.S. Department of Labor, 2008), requiring underground coal mines to supply mine emergency RAs and associated components so as to provide a life-sustaining environment for persons trapped underground. Such RAs can be either selfcontained mobile units or built-in-place facilities. The regulatory changes also include provisions establishing requirements for the approval of RAs and their components by the U.S. Mine Safety and Health Administration (MSHA), among which are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One criterion for maintaining a safe RA atmosphere is the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (specified as 0.18 psi, or approximately 5.0 in. H2O), or as specified by the RA manufacturer, above mine atmospheric pressure in the RA (U.S. Department of Labor, 2008)."

Oct 1, 2016

By P. Anyon

Exposure to the microscopic particles in diesel engine exhaust can lead to serious health problems, including the incidence of cancers, heart disease and increased susceptibility to respiratory ailments such as pneumonia, bronchitis, and asthma. In Australia, mining companies and state government authorities are actively responding to this major occupational health and safety issue. Their initiatives place considerable emphasis on routine monitoring of diesel particle matter (DPM) exhaust emissions, both for engine benchmarking and as a part of routine engine maintenance. Implementation strategies follow two complementary paths: determination of individual engines? emission signatures combined with periodic engine re-certification; and co-operatively agreed industry-government engine maintenance programs, which are subject to audit. Both strategies place heavy reliance on real-time measurement of DPM concentrations in engine exhaust, using ruggedized instrumentation, mainly based on laser light scattering photometry. Adding value to this cooperative approach, industry has also collectively funded a government agency to design and manage a database, into which the results of all-routine DPM testing can be uploaded directly by individual mines. This win-win outcome is a great example of how cooperative action between governments and industry can deliver the goods: in this case, a safer working environment, more efficient energy use and the capacity to benchmark performance with industry peers.

Jan 1, 2009

By W. R. Crank

[Rock bursts are phenomena associated with mining operations, particularly with deep mining, although they occur throughout a wide rump, of depth, from 600 feel downward. The intensity is usually in direct proportion to the depth, varying from a loosening and sloughing off to a violent rupture, giving rise to the term, "explosive rock." The more or less violent breaking of rock in mine working, tins been variously designated as " flaking," "pressure hoists," "strain bursts," "bumps," "quakes," and "air blasts," which indicate opinions as to cause and effect. The term "air blast" lots probably beat most widely used, and naturally so, as a more or less rapid movement of air often accompanying the more violent phenomena of rock failure. Furthermore, there is an implied if not definitely expressed degree of magnitude in the action designited by a given term and in the cause and character of the action. For example. flaking, pressure bursts, and quakes are terms ranged to indicate action of increasing magnitude; and pressure bursts, strain bursts. bumps, and quakes are ranged according to the cause and character of the action.]

Jan 1, 1929

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By Dan A. Brown

This paper describes a method of conducting rapid lateral loading tests of deep foundations in which the load is applied to the foundation with a time duration of less than one second. For purposes of this paper the loading is applied using a pyrotechnic loading system commonly referred to as Statnamic. However, the method should apply to any lateral loading system which produces a force time history with a loading duration of 20 msec to 1 second. The test provides a measure of the dynamic and static response of the soil/foundation system and must be evaluated as a dynamic loading. Interpretation of the test includes a simple single degree of freedom (SDOF) model which can account for the inertial effects of foundation mass, system damping, and static foundation stiffness. The results of the test measurements are compared with four case histories in which comparative static load test data are available, including pile group foundations and large diameter drilled shaft foundations.

Jan 1, 2007

By J L. Mauk

The Sovereign, Jubilee, Scotia and Jasper Creek prospects occur in an area of ~3.0 km by 2.5 km (~7.5 km2) in the Hauraki goldfield. The prospects are hosted by andesitic to dacitic flows, autoclastic breccias and localised pyroclastic and air fall deposits. Jubilee and Sovereign prospects lie along the northern and southern parts of the Waitekauri Fault, respectively, whereas Scotia is located ~1 km to the E, and Jasper Creek a further ~1.2 km to the ENE. Wall rocks are typically intensely altered, although the degree of alteration becomes more variable east of Scotia and at Jasper Creek. Alteration minerals include quartz, adularia, albite, chlorite, pyrite, illite, interstratified illite-smectite, smectite and calcite. Several of these minerals have distributions that show distinct zonation with adularia most abundant at Sovereign and Jasper Creek, but restricted to shallow levels at Scotia. Illite occurs throughout Sovereign and Jubilee plus the western margin of Scotia where it grades into interstratified illite-smectite; smectite predominates at Jasper Creek. Veins are uncommon and typically narrow, but show distinct zonations. Quartz veins are more abundant at Sovereign and Jubilee, whereas calcite veins are more abundant at Scotia and Jasper Creek. Laumontite veins occur at Scotia, and rare clinoptilolite, mordenite and stilbite veinlets with calcite occur at Jasper Creek. Fluid inclusion in quartz and calcite homogenised between 141¦ to 272¦C and trapped a dilute solution with an apparent salinity of less than 2.6 weight percent NaCl equivalent. Homogenisation temperatures are hottest at Sovereign (average 241¦C) and Jubilee (average 239¦C), cooler at Scotia (average 204¦C) and coolest at Jasper Creek (average 162¦C). Calculated paleowater table elevations suggest the water table was 680 m to 750 m above sea level at Sovereign and Jubilee, 450 m at Scotia and 225 m at Jasper Creek. The current data suggest three scenarios that can explain why Sovereign and Jubilee are deep and hot, whereas Jasper Creek is cool, shallow and marginal; 1.   some or all of the prospects may represent separate overlapping hydrothermal system, 2.   a high-relief hydrothermal system on the side of volcano with an inclined water table and outflow towards Jasper Creek, and 3.   a low-relief hydrothermal system that has been either tilted or block faulted with greatest uplift and erosion to the west.

Jan 1, 2005

By D. E. Larson

The U.S. Bureau of Mines investigated Fe-base alloys containing 8 pet Crwith Ni, AI, and Si additions as substitutes for standard AISI Type 304 stainless steel (SS) in high-temperature oxidizing applications. The objective of this study was to reduce the amount of Cr required to make an austenitic stainless steel while retaining satisfactory workability, mechanical properties, and oxidation resistance. Alloys prepared in this investigation had a composition of Fe-8Cr-lMn-0.07C with varying amounts of Ni, AI, and Si. A minimum of 10 pet Ni was required to achieve an austenitic composition. The microstructures of the austenitic alloys were very susceptible to room-temperature, deformation-induced martensitic transformations. When the alloys were cold worked or stressed, the materials had far greater tensile strengths than Type 304 SS at room temperature. At higher temperatures, tensile strengths and workability of several of the alloys were comparable to that of Type 304 SS. Although martensitic transformation caused the room-temperature properties of the experimental alloys to be quite different than those of Type 304 SS, the superior oxidation resistance and similar hot workability of several alloys encourage their use as replacements for Type 304 SS.

Jan 1, 1989

By Osvaldo A. Bascur

Connectivity between mining and metallurgical process operations and their business systems has become a reality. Expanded use of plant information on the desktop is a standard tool for revenue improvement, cost reduction, and adherence to production constraints. The industrial component desktop support access to information for continuous improvement and innovation by staff personnel and engineers. Collaboration between groups enables the implementation of an overall process effectiveness index based on losses due to equipment availability, production recovery and quality rate. In this sense, the paper point out three cases studies of large integrated power stations.

May 25, 1998

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Floyd County in beds 28 inches or more thick, in thousand tons, is as follows: [ ]

Jan 1, 1958

By D. E. Kirby

The electrochemical reduction of AlC13 was investigated as a process for the production of aluminum. An externally heated, single-compartment cell with a rammed refractory lining was used with molten KCl-NaCl-AlC13 electrolyte. Aluminum was deposited qt 700° to 760° C with a current of 100 to 200 amperes on a molten aluminum cathode. Chlorine was evolved at a graphite anode and collected and measured to provide a quantitative evaluation of the AlC13 reduction. Aluminum was removed from the cell by siphoning or ladling. Granular AlC13 was added periodically to replenish that depleted from the electrolyte. Concentrations of 7.5 to 17.5 percent AlC13 in the electrolyte were optimum for operation. Anode current efficiencies of 83 to 85 percent were attained, using anode current densities of 5.9 amperes per square inch and an anode-cathode distance of 4 inches. The chemically bonded, alumina liner was resistant to attack by aluminum and chlorine but susceptible to erosion at the surface of the electrolyte. Titanium diboride proved suitable for the electrical connection to the molten aluminum cathode. Aluminum of a purity equal to or better than 1100 series metal was electrowon continuously from commercial AlC13 for a period of 4-1/2 months.

Jan 1, 1970

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

LANDSAT imagery has renewed interest in linear features first recognised by E. S. Hills in a physiographic model of Australia. Certain of these lineaments are aligned with structures which control mineralisation.Lineament guidelines are potentially useful in many poorlyexposed areas if they can be recognised early enough in exploration and drilling programs leading to mine development.A case history based on the Charters Towers Gold Field indicates that lineament guidelines can be established early enough to guide development ofnew mines. The position of the Charters Towers Lineament was known as early as 1956. Subsequently, more detailed publications identified and classified associated lineaments which provide intersections correlated with gold occurrences. The discovery of a significant orebody at one of the most prominent lineament intersections came in 1975. Mine drilling has confirmed the influence ofintersecting structural trends indicated by lineaments but not by previous regional mapping.Recent gold discoveries south of Charters Towers lie in a grid of prominent lineaments. The development of mines about Charters Towers will provide additional understanding of relationships between centres of mineralisation and lineament intersections. This understanding may in future be sufficient to encourage exploration for a new generation of concealed gold deposits in northeastern Queensland.

Jan 1, 1986

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining usage in the mining industry. A variety of machines currently finds employment: tunnel boring machines, roadheaders, continuous miners, surface miners, and augers. These machines have advantages compared to drill and blast mining methods, including increased safety, lower cost, uniform muck size, and accurately sized openings. A century of experience with mechanical methods has already paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hardrock mechanical mining machines. Mechanical miners will become integrated mining systems and will determine the design of mines, when several significant challenges have been met.

Jan 1, 2001

By F. T. Da Silva

Concentrates of titaniferous minerals containing around 30 wt% Ta2O5 are processed hydrometallurgically by hydrofluoric acid leaching and solvent extraction, followed by the precipitation of hydrated potassium heptafluorotantalate. A fundamental study of the thermodynamics of this precipitation and recrystallisation was undertaken to increase understanding of the conditions most conducive to the production of pure, well-crystallised K2TaF7. Activity-pH diagrams for the Ta-K-F-H2O system explained the dissolution of Ta2O5 in fluoride solutions quite well and also the precipitation-recrystallisation of K2TaF7.H2O. X-ray diffraction and scanning electron microscopy confirmed the thermodynamic observations. It was concluded that the best precipitating agent for K2TaF7 from fluoride solutions is KF but a recrystallisation step in a HF environment produces purer, well-crystallised K2TaF7.H2O, eliminating oxy-salts and other impurities

Jun 21, 1905