Search Documents

By Peter Cali, David Yang, Rakshya Shrestha, Ralph Griffin, Sushil Kafle, Motoji Watanabe

"As a part of the ‘US Army Corps of Engineers - New Orleans to Venice, Louisiana Hurricane Protection Project’, deep mixing ground improvement was designed to reinforce the soft ground for the emergency repair of a 7297-foot (2,224 m) long section of the Mississippi River West Bank levee in Buras Levee District under the contract ‘Emergency Levee Repairs – Contract P-17A, Plaquemines Parish, Louisiana’. The ground improvement utilizes a series of soil-cement panels oriented in the transverse direction of the levee. Each soil-cement panel consists of overlapped columns installed by the deep mixing method (DMM). DMM is performed from the existing top of levee and extended to competent stratum at depths varying from 26 feet (7.9 m) to 47 feet (14.3 m) below the working platform. The main purpose of the DMM panels is to provide shear resistance to the levee against lateral loads at high flood water condition. The DMM panels support the additional vertical load created by the increased height of the levee for hurricane protection and control the long-term settlement of the remediated levee, which might otherwise occur due to the compression of soft foundation soils. The total amount of DMM treatment is approximately 54,000 cubic yards (41,500 cubic meters). This paper reviews the project background, subsurface soil conditions and presents the design, construction and quality control of the deep mixing work for this levee repair project.INTRODUCTIONIn August 2005, Hurricane Katrina caused major damage to the federal and non-federal flood control projects in southeast Louisiana. In September 2005, Hurricane Rita caused further damage to this flood protection system. In an effort to minimize further damage and to enhance the protection level, certain non-federal levees located on the west bank of the Mississippi river in Plaquemines Parish, Louisiana were incorporated into the New Orleans to Venice Hurricane Protection project by the US Army Corps of Engineers (USACE). DMM techniques were then utilized by the USACE in several of these emergency projects and in many medium sized projects between 2006 and 2010 (Bruce et al. 2012). This project (called P-17A hereafter) which forms a part of this protection system is executed under the contract Emergency Levee Repairs, Contract P-17A. This is one of the largest projects of the USACE after LPV- 111. The huge LPV-111 project (5.5 miles (8.9 km) of levee) treated by DMM), the largest DMM project ever conducted outside Japan, began in 2010 and was completed in 2012 (Cali et al. 2012, Bruce et al. 2012).DMM is utilized at P-17A to construct a series of soil-cement panels oriented in the transverse direction of the existing levee to provide shear resistance to the levee against the lateral load during high flood water condition. The project extends 7297-foot (2,224 m) along the West Bank Levee of the Mississippi River in the Buras district of Louisiana, parallel to Louisiana Highway 23 (LA-23) as shown in Figure 1. It is located approximately 60 miles (96 km) south-east of downtown New Orleans."

Jan 1, 2015

By Henry Kreisinger, WALTER T. RAY

In its investigation of more efficient methods for utilizing the coals and lignites in the United States, to the end that waste might be avoided, the value of low-grade coals increased, and the life of the nation's fuel resources prolonged, the technologic branch of the United States Geological Survey carried on a study of the factors involved in the manufacture and use of briquets, including the suitability of various coals for briquetting, the cheapest and most satisfactory binders, and the furnace behavior and evaporative efficiency of briquetted fuel. The investigations had their beginning in the work done at the coaltesting plant at the Louisiana Purchase Exposition, St. Louis, Mo., in 1904, and were continued at St. Louis and later at Norfolk, Va. Accounts of various tests and statements of the conclusions to be drawn from them have appeared in a number of bulletins. a In connection with the work at Norfolk, comparative steaming tests were made in stationary, marine, and locomotive boilers with run-ofmine coal and the same coal formed into briquets of two sizes. The tests in a locomotive boiler that are described in detail in this bulletin were undertaken to add cumulative evidence to work done at other places. They were made possible through the courtesy of the Seaboard Air Line Railway Company in supplying both the locomotive and the coal used. During the trials the locomotive stood on a side track in the shop yards of the railway company at Portsmonth, Va. No running tests were made.

Jan 1, 1911

By Ruth F. Brinkley

This report is the 18th of a series of reports originally issued annually, and more recently bienially, to acquaint the public with the work of the Federal Bureau of Mines in explosives technology. Part I reviews briefly the overall activities during fiscal years 1957 and 1958.4/ Part II presents in abstract form the publications prepared by the Bureau that appeared during the period.5/

Jan 1, 1961

By Charles E. Whieldon

Data on the oil fields in Mahoning Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and com- piled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

Although the Stamler feeder/breaker has been used for coal crushing in underground mines for many years, it has only recently been applied to other crushing operations. Two companies presently using Stamler feeder/breakers for rock crushing were contacted regarding their experiences with the units in actual field use. In both cases information was obtained directly from the individuals responsible for field operation and maintenance of the units. White Pine Copper Co. has been using Stamler feeder/breakers for over two years to crush copper ore. They now have fourteen 450-ton-per-hour units on line. The ore has a compressive strength of from 18,000 to 28,000 psi and is extremely abrasive. Maintenance is performed on a tonnage basis. The breaker shaft is replaced every 250,000 tons (requiring about 4 hrs) and picks are replaced about every 1500 tons by the operator (requiring about 2 min per pick). Very little unscheduled maintenance has been required. Crushing costs are fairly high (estimated at 13 to 15t per ton including maintenance and operation) because of tale extreme abrasiveness of the material. A new Stamler feeder/breaker with Ultramet wear surfaces was put or line in June 1976. Ultramet was found to increase the life of belt transfer station surfaces by up to 400 percent and it is hoped that it will do the same for the feeder/breaker. At this time it is still too early to evaluate the performance of the Ultramet unit. If it does improve abrasion resistance, crushing costs could be greatly reduced. White Pine is very pleased with the units and the service provided by Stamler.

Jan 1, 1976

By James L. Poole

The gold and silver markets from the late 1960's to the present are reviewed and the outlook for these metals in the 1980's is presented. Included in this discussion is a summary of the basic supply and demand balance for gold and silver since the mid-1960's. an explanation of the price formation for the metals, some of the relationships between the prices of these metals and selected economic parameters, and how these factors affect the outlook.

Jan 1, 1981

Entry of personnel under a vertical raise bored hole is not standard practice in Australia. Where access is required below a rise, mining operations must be confident that they understand the capacity of the ground control specified and installed. Physical modelling was conducted on Callie mine to evaluate the performance of 5 mm steel wire weldmesh secured to the base of a vertical raise bored hole of 1.4 m diameter. Joint orientation data was used with Unwedge to calculate a series of potential wedges likely to form within the rise. The mass of the most likely wedges were then replicated by collecting rocks in 5 kg increments (¦10 per cent), which were allowed to freefall onto installed mesh at the base of a 40 m vertical rise. The results indicate that two sheets of mesh can retain a freefalling rock of at least 20 kg mass although rupture of strands can result. This paper outlines the test conditions, expected results based on theoretical calculations and actual outcomes of the testing.

Nov 25, 2010

By John F. McCoy

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller Associates, Inc. (FMA) to develop guidelines for designing, constructing, stocking and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressurization Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

This paper summarises the development t,) date for the Hidden Valley Gold (HVG) Project. It starts with the original exploration work, covers the detailed feasibility study activities and concludes with the current phase of extra exploration drilling. A brief technical summary has been made from the various mining, process and environmental studies that were undertaken as part of the project approval process. A discussion of the influential non-technical factors is included, as well as a view of the future prospects for an operating mine. The project was always seen as marginal, given the low grades, small resource and short mine life. However the capital and operating costs were lowered with aggressive design and it was regarded an acceptable development by CRA. The opportunity was taken to review the project when delays in start-up were encountered. An updated financial evaluation showed a subeconomic resource in 1990 terms and this resulted in a new exploration phase to identify a larger deposit.

Jan 1, 1991

By Fred D. DeVanery

"INTRODUCTION Although galena is the most common lead-bearing mineral, is easily concentrated by gravity methods, and is readily susceptible to flotation, nevertheless some galena-bearing orebodies have within them small deposits of lead ore that fail to give a high recovery when treated by the customary milling methods.The secondary minerals, cerussite and anglesite, which result from natural oxidation of galena, cause losses when the customary method of lead-ore concentration is practiced. The identification of oxidized lead-ore minerals and the efficient concentration of a lead ore taken from the oxidized portion of an orebody which has previously yielded poor recoveries mere the objects of a recent investigation. Thus the ore examined was selected from a large orebody. The work was undertaken at the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo.DESCRIPTION OF OREThe ore was of a brownish color owing to oxidation of some of the iron minerals to limonite. The lead content was 6.80 percent, and a cursory examination showed that most of the lead was present as galena. Small amounts of sphalerite, siderite, and pyrite were readily identified. The chief gangue mineral was dolomite, accompanied by smaller amounts of calcite and glauconite."

Jun 1, 1933

By Joan T. May

The Bureau of Mines conducted laboratory tests to evaluate the production of high-purity H3P04 by HCl digestion and solvent extraction. Both batch and bench-scale continuous tests were made. Western phosphate rock concentrates were acidulated with HCI, and the digestion liquors were processed by solvent extraction. Phosphoric acid was extracted with isoamyl alcohol and recovered from the organic extract by contact with an NH4F solution. This solution was fractionally distilled to yield high-purity H3P04. The raffinate from solvent extraction was treated with lime to precipitate CaF2, which was subjected to steam pyrolysis to generate HF. This method was successful in recovering 95 pet of the phosphate and 80 pct of the fluoride contained in the concentrates.

Jan 1, 1976

By H. J. Siriwardane

This paper presents results from three case studies involving longwall mine panels at which the measured ground movements were compared with the numerical model predictions based on the finite element method. A new approach called the "displacement approach" was used in this study. The general concept of this method is based on the assumption that total roof collapse occurs behind the mine face as it advances. This assumption appears to be true for almost all longwall mining conditions. The prediction based on the numerical model appears to compare well with the measurements.

Jan 1, 1988

By B. W. Gandrud

[This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests mode by the Bureau of Fines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers. The Klandyke mine, operated by the Blocton Mining Co., is about 1 mile eat of Vest Blocton, Bibb County, Ala., floor the southwestern, extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the, washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/ one on the tabling of fine coal from the Thompson and Woodstock beds5/, and the third a washability study of the Henry Ellen bed at Acmar6/.]

Jan 1, 1939

By R. S. Handy

AT THE TIME of my first visit to Bolivia in 1927 the tin-mining industry was prosperous, the tin price at London being more than £300 per long ton of tin, and the operators were making every effort to bring their plants up to the very highest point of capacity as well as of efficiency. Any device or piece of equipment or method that gave promise of increasing production was welcomed regardless of the cost, and the plants were being modernized as rapidly as human ingenuity could make it possible. At the time of my second visit in 1932, however, conditions had changed materially. The price of tin had fallen to a little over £100 but costs had not decreased anywhere in proportion and operators were at their wit's end to cut the operating losses that were everywhere prevalent. Charles L. Bradbury, manager of the Empresa Minera de Huanuni, at Huanuni, Bolivia, had been recently called from Mexico to make all analysis of the situation and to attempt to work out a remedy for the economic conditions that threatened to close the mine. His analysis brought out the following points:

Jan 1, 1938

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

The National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study to optimize the rib control plan in a room-and-pillar coal mine. The study mine is located in the Central Appalachia coal basin. Two monitoring sites were selected at different sections in the study mine. The selected sites have different overburden depths and geologies. The instrumentation plans at study sites include borehole pressure cells installed at various depths in studied pillars, rib and roof extensometers and load cells mounted on number of the rib bolts. The instrumentation results and observed geology for one of the study sites showed great potential for optimizing the rib bolt plan at that section of the mine. Therefore, a rib support optimization study was followed using numerical modeling technique. A calibrated threedimensional model was developed using the instrumentation results of the optimization section. The calibrated model was used to determine the optimum rib support for expected overburden depths and rib heights. Baseline rib bolt patterns were assumed for the optimization study. Additional rib bolts, above and beyond the baseline bolting parameters, were outlined and identified as solutions to contain the rib fracturing identified by the modeling results.

Jul 28, 2020

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

By B. McLaughlin

"The Penna shaft is the deepest single-lift shaft in North America. Agnico-Eagle started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1800 t/d from a 2240-m deep shaft. Exploration success at depth led to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7000 t/d. The use of another double drum hoist, instead of a Blair multi-rope winder, to hoist 24.5 t skips was only made possible by lowering the safety factor.This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of 3 km. IntroductionThe original Penna production hoist was a 4.88 m (16 ft) diameter double drum and single clutch machine. Béliveau (1996) and Scott (1996) have described this hoisting plant. In 1998, a decision was made to increase mining capacity from 1800 t to 4500 t of ore per day from the shaft bottom. Final capacity had to include an allowance of 1800 t of waste per day for future capital projects. While daily capacity was to be 6300 t, it would, by taking into account the different rock densities, be equivalent to hoisting 7000 t of ore.The steps taken to lower the safety factor were presented by McLaughlin and Scott"

Jan 1, 2004

By John D. Godfrey

A brief account of economic developments in and around northeastern Alberta is presented and mention is made of mining and industrial developments currently of interest in the area. Planned and projected operations are briefly discussed for this region. The history of geological surveys and mining activities in the Shield area of Alberta and the adjoining parts of Northwest Territories and Saskatchewan is traced. Reassessment of the presently-known economic picture of northwestern Canada in conjunction with some recent information on Precambrian structures of northeastern Alberta points to some interesting mining possibilities, particularly in and around that province.

Jan 1, 1960