Search Documents

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By Lees M. G, Vitnell B. W

The post-war need to increase coal production promoted an intensive drilling campaign. Ineffectiveness in core recovery inclined the coal industry towards percussion drilling rather than diamond drilling. The Joint Coal Board, recognising the greater potential of core drilling, has actively encouraged improvement in techniques and equipment. One outstanding need was a barrel which, over and above other improvements being achieved, would permit recovered core to be examined before it had been subjected to the increased fragmentation and displacement which to date has been inevitable except in core which has been drilled in solid sticks û as New South Wales coal rarely can be drilled. In conjunction with Triefus Pty Ltd a barrel with a split inner tube has now been evolved, as a result of which, core can be more accurately logged, division in to lengths for analysis more aptly made, any core loss more reasonably allocated to appropriate plies, and a greater percentage of core recovered û of the order 95 per cent and more. The one half of the split inner tube is lifted from the other and the logging completed before the core is disturbed.

Jan 1, 1957

By J Pearse, N Acosta, N McIntyre, M Angarita, L Camacho, C Huguet, D Arbelaez-Ruiz, J Ossa-Moreno, O Restrepo

Colombia is an example of a nation where mining makes a significant contribution to local and national economies. Due to the abundant resources present in the ground, there are good prospects for further development. However, the impacts of mining projects can include reduced access to good quality freshwater for other economic activities and/or biodiversity preservation (Ossa et al., 2018). As well as the water management challenges common to all mining regions globally, Colombia has particular challenges associated with its biophysical and socio-political traits. Land use change in many regions is dynamic including rapid development of agriculture and the development and abandonment of small scale mines. The value of ecosystem services provided by prospective mining regions also creates challenges in particular with regard to the páramos, the headwater wetlands from which about 70% of Colombia’s water supply has originated (Cleef 1981). Colombia also has particular challenges related to strong preconceptions about mining and its impacts on water. On the one hand, there is recognition that new large-scale mines are important for Colombia’s economy; on the other, there is deep distrust of the sector’s ability to operate with minimal adverse impacts (Gutiérrez-Gómez, 2017). Hence, any impact assessment is likely to face high levels of scepticism and scrutiny. Summarising the work of McIntyre et al. (2018), this abstract proposes a framework for assessing and communicating risks to regional water resources arising from the impacts of mines. The framework outputs aim to provide government and other stakeholder groups the scientific evidence needed to inform their viewpoints about mining development in the selected region, and a baseline from which to design a program of priority scientific research. CITATION:McIntyre, N, Angarita, M, Acosta, N, Camacho, L, Pearse, J, Huguet, C, Restrepo, O, Ossa-Moreno, J and Arbelaez-Ruiz, D, 2018. A framework for assessing and communicating water risks in prospective mining regions of Colombia, in Proceedings Life-of-Mine 2018, pp 49–51 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By W. S. Sanner

Anthracite was used extensively as a fuel in iron metallurgy from 1840 to 1880. In 1874, 226 of the 680 blast furnaces in the United States were operating on anthracite and producing almost one-half of the Nation's pig iron. However, by 1890, railroad expansion, the development of western iron-ore reserves, and the growing use of coke decreased the importance of anthracite as a metallurgical fuel. As a result, the last blast furnace designed exclusively for anthracite use was built in 1891. Because of the increased energy requirements of our expanding national economy, the abnormally high demands during national emergencies, and the proximity of anthracite deposits to eastern steel-producing areas, interest has grown in again using anthracite in iron metallurgy. Estimates of anthracite reserves indicate a 300-yr. supply at a production rate of 30 million tons per year. These large reserves dictate the development of an adequate technology for the use of anthracite by the metallurgical industry.

Jan 1, 1961

By Robert C. Freas

Dravo Lime Company has opened a new 290m (940 ft.) deep lime-stone mine near Maysville, Kentucky. As the mine was opened there were many unknowns as to the stress relationships within the rock, and their influence, if any, on the selected mining method. Therefore, a system of overlay geologic and structural maps, borehold extenso-meter measurements, and oriented photography was developed for the purposes of monitoring the internal structural relationships of the rock mass. This paper presents a description of the methods used, the observations made, and the conclusions and recommendations made as a result of the initial monitoring program.

Jan 1, 1977

By Leonard Obert

This report describes a gage which, when used with my procedure for producing strain relief, will measure the resulting borehole deformation, From the borehole deformation the magnitude and direction of the principal stresses in a plane normal to the axis of the borehole can be calculated. The design considerations, mechanical construction, sensitivity, and stability of the gage are discussed. INTRODUCTION During the past two decades an increasing mount of consideration has been given to the problem of measuring and evaluating stress in rock around underground openings. Several investigators have made theoretical and model studies of the stress and (or) strain concentrations around simulated mine openings or in structural members, such as mine pillars or immediate roof. Other investigators have developed gages for directly or indirectly measuring stress or strain, and a number of reports present the results of measurements made with these gages. Because various methods and instruments have been developed, factors involved in this type of measurement will be briefly considered.

Jan 1, 1962

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

By Sergio N. Monteiro, Artur C. Pereira, Foluke S. de Assis

Jute fibers are among the lignocellulosic with great potential for use in polymer composites. In this work, polyester matrix composites incorporated jute fabric were investigated for their flexural behavior. Specimens with up to 30% in volume of jute fabric were bend-tested until rupture. The results showed an increase in both the composite mechanical strength, principally to a polyester composite reinforced with 30% in volume of jute fabric. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the jute fabric and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.

Mar 1, 2018

By D. A. Elkins

Design plans and detailed cost estimates of mining and treating ore from Maggie Canyon deposit by two alternative methods which can be used in the event of a sudden need to exploit this resource are given . Lower costs are estimated for the operation employing oil - emulsion flotation . The total capital investment required for this operation is estimated at $ 11,750,000 . Assuming an 85 percent recovery in mining , 55.6 pct of the manganese in the ore reserve would report in 153,333 tons of ferromanganese containing 75 pct manganese . The production cost for the 5 - year operation would be about $ 245 per ton of ferromanganese . The total annual operating cost would be approximately $ 7.5 million , distributed , in pct , as follows : Mining 11.9 , milling 24.4 , sintering 9.9 , smelting 47.2 , hauling ore and sinter 2.8 , and general offices 3.8 . Recovery and costs are both higher for the operation employing dithionate leaching . In this operation the required investment is about $ 17,220,000 . Manganese recovery would be 67.6 pct in 186,160 tons of ferromanganese . Production cost would be about $ 284 per ton of ferromanganese . The total annual operating cost would be about $ 10,575,000 , distributed , in pct , as follows : Mining 8.4 , milling 44.4 , sintering 7.4 , smelting 34.7 , hauling ore and sinter 1.3 , and general offices 3.8 . Potential process modifications might reduce the operating cost of the first operation by as much as 7 pct and that of the second operation by as much as 9.5 pct , but exploitation of the deposit by the techniques studied is not economical today .

Jan 1, 1964

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By F. Mielli

Camera systems and video surveillance are usually associated with people and asset protection. However, they can be applied in a mine environment beyond conventional surveillance: For process monitoring, collision avoidance, sizing, flotation cells, conveying systems, blasting, objects and people tracking, thermal profile, and to automatically identify equipment that is missing parts,. Image and video solutions can be driven by better integration of powerful video analytics and cameras systems in automation tools such as process controllers and supervision systems.

Feb 27, 2013

By J. O. Osterberg

The realities of foundation enginering are that the work never proceeds exactly as expected. The various reasons, exploration, design, construction, and legal are discussed. Case histories are presented with an analysis of why the projects did not turn out as expected and how the difficulties might have been avoided.

Jan 1, 2010

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By A J. Cornah

Critical decisions in iron ore project evaluation and production are based on global and local spatial estimates of primary mineral deposit properties (such as in situ geochemical grades) and geometallurgical responses (such as screened, washed or concentrated product yields and grades), which are derived from limited sample data. These spatial estimates are typically made using classical geostatistical techniques, which fundamentally assume that the attributes of interest behave additively. This assumption is generally appropriate for æprimaryÆ variables but æresponseÆ variables may behave non-additively and therefore their direct linear estimates may be biased.In this paper an existing additivity testing mechanism is used to quantify the bias resulting from direct linear estimation of a non-additive iron ore attribute. Data from a magnetite project are used to determine the circumstances under which such biases may be of material impact. The implications for iron ore resource estimation, geometallurgical modelling and grade control are outlined and discussed.CITATION:Cornah, A J, 2013. Assessment of the impact of non-additivity in the estimation of iron ore attributes, in Proceedings Iron Ore 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Nav Dhadli

Tailings from Oil Sands MiningWhat are they? Challenges Solutions Regulatory Environment Definition of the AFD Tailings Treatment Process 2010 AFD Pilot/Demonstration ProgramTechnical challenges Performance and Results Next steps Oil Sands Industry Collaboration on Tailings Technology TAILINGS ?WHAT ARE THEY? Mixture of remaining water and solids following bitumen extraction process Composed of water, sand, silt, clay, small amounts of hydrocarbon (bitumen, solvent, and asphaltenes) A necessary part of production in excavation of oil sands and removal of bitumen

May 1, 2011

By F. D. Aaring

"IntroductionTHE PINCHER CREEK gas condensate field, in Township 3, Range 28, and Townships 3 and 4, Range 29, West of the Fourth Meridian, was discovered in 1947 by the Canadian Gulf Oil Company with the completion of Pincher Creek No. 1 well in the Madison lime-stone of Mississippian age.This discovery was the result of a great deal of detailed seismic work in the area and is a credit to the geophysical personnel of the Company. The depth of the reservoir varies from 7,400 feet to 8,200 feet subsea, with the established water level at -8,200 feet. The predicted depth was but a scant 100 feet from that found in the discovery well, at 11, 705 feet. Since the discovery of the reservoir, three additional wells have penetrated the Madison limestone and have further verified the original •seismic interpretation of the limits of this reservoir.To date, •only a very small amount of gas has been produced from this field. Consequently, the reservoir studies that have been made so far are predominantly based on investigations of the phase behaviour of the fluid and physical characteristics of the reservoir rock. In view of the above limitations, it has been necessary to set up and perform model reservoir studies with the fluids and to recover as much core from the productive Madison limestone as possible in order that it might be analysed by conventional laboratory technique and be subjected to detailed microscopic geological examination."

Jan 1, 1952

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

Recent work on decoppering lead is reviewed CUS is formed rapidly even from dilute solutions of copper in lead. The mechanism of decoppering is discussed and an explanation for the retention of metals such as silver in lead is advanced. As decoppering tin appears to be an analogous process, the, Cu-Sn-S system is studied at 300°C.. CuS, which is not an equilibrium product, is found m decoppermg drosses. In the removal of nickel from lead, Ni3Pb2S2 is formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by stirring in sulphur. Decoppering bIsmuth IS thermodynamically favoured, but is complicated by the occurrence of CuBiS2 The Cu-Pb-S system IS the only one of the four studied where the equilibrium can be calculated simply, as the presence of ternary sulphIde or other phases invalidates calculations based on binary data.

Jan 1, 1971

By R G. Barker, A B. Christie

Minerals are necessary for providing almost everything we take for granted in our daily lives including food, shelter, and supplies of energy and water. Minerals are therefore essential for the maintenance and improvement of the standard of living of all New Zealanders.

Jan 1, 1998