Search Documents

By Fuqiang Zheng, Yufeng Guo, Pengfei Li, Guanzhou Qiu, Tao Jiang, Andrew Yakovlevich Travyanov

Low content of TiO2 and high impurities content of Ca and Mg are the shortcomings of domestic ilmenite. To meet the requirements of the material in the titania produced by chlorination process and titanium sponge industry, enrichment of ilmenite is necessary. In the process of enriching ilmenite, high temperature and reductive condition were beneficial to the formation of anosovite, but the high content of magnesium oxide which was solid soluble in anosovite baffled the following separation. So the effects of pre-oxidation and reductive conditions including reduction temperature, reduction time and hydrogen concentration on the phase composition and metallization rate were studied. The characteristics of reduction samples were analyzed by X-ray diffraction and optical microscope. Results have shown that the reduction product is mainly composed of Fe, Fe(Mg)TiO3 and TiO2 at 1123K, its metallization rate is about 65%,magnesium exists in Fe(Mg)TiO3.

Jan 1, 2015

By David N. Hanlon

The effect of high-temperature plastic deformation of the austenitic phase (y) on the subsequent phase transformation to ferrite (a) has been experimentally investigated, and modelled using a physically-based model. The effect is of importance for steel sheet, in view of me significance of the phase transformation with respect to the eventual properties of the material. In this paper the kinetics of the y ? a phase transformation has been studied after different degrees of prior deformation. The degree of deformation is varied by applying different deformation temperatures and strain rates, and by allowing a varying extent of recovery and recrystallisation. Consequently, both dynamic and static recovery and recrystallisation have been involved. The dilatometric observations on the phase transformation have been modelled using an interface-mobility model, in which the effect of the dislocation structure is introduced as an additional driving-force term. The effect of the stored energy on the nucleation process, which appears to be affected more strongly than the growth of ferrite, is examined in terms of the classical nucleation theory.

Jan 1, 2001

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By Ryosuke O. Suzuki

A new cell concept for calciothermic reduction is proposed in which the titanium dioxide instead of TiCl4 is used as the raw material for reduction, Metallic calcium is needed as the reductant of a thermochemicaily stable oxide, such as TiO2. CaCl2, is selected as the solvent of Ca and simultaneously as the solvent of CaO. The reduction system consists of a single cell where both the reduction reaction and the electrolytic reaction for recovery of reducing agent coexist in the same molten CaCl2 bath. A few mol%Ca dissolves in the melt and gives the media a strong reducing power. Sufficiently deoxidized metallic titanium deposits and forms a slightly sintered granular sponge. Both mechanisms of the halide flux deoxidation and the electrochemical deoxidation work efficiently for these fine precipitates, The reducing agent is in situ recovered by electrolysis of CaO because the molten CaCl2 he a relatively large solubility for CaO Some cell designs and modifications are proposed for industrial applications.

Jan 1, 2003

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or hear it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By Egil Krystad, Merete Tangstad, Kai Tang, Gabriella Trenell

"A new UMG-Si refining concept has been proposed in this paper. Liquid Si and another liquid metal phase (Me) were separated by the molten slag spontaneously based on their different physicochemical properties. Two metal/slag distribution reactions are able to occur in the system simultaneously. Experimental investigation on the B and P distribution equilibria among Si/slag/Me was carried out in the graphite resistance furnace under the inert atmosphere. The B and P doped silicon was in equilibrium with either the SiO2-CaO or SiO2-CaO-l0%CaF2 slags at 1600 and 1650°C, respectively. The pure Fe and Cu metals were used in order to ""capture"" B and P in the slag phases. B and P in samples were determined by the ICP-MS. B and P distribution coefficients for the Si/slag/Me equilibria were compared with the theoretical calculations. The possible kinetic barriers for the Si/slag/Me three-layer equilibria have been analyzed. The metal contaminations in the three-layer equilibria were also examined. The present study provides a new approach for the refining of MG-Si.IntroductionMost of the impurities in the metallurgical silicon (MG-Si) are rather ""dilute'', ranging from few to several thousand ppms. However, the target impurity levels for upgrade metallurgical silicon (UMG-Si) feedstock are often far below the level of ppm. In such extreme case, the conventional refining technologies face the great technical challenges. B removal by slagging has already been implemented industrially. Removal of Pis frequently carried out by the vacuum distillation. The separating treatments for B and P removals lead to increase refining cost, total CO2 emission and longer pay-back time of solar cell module.It is well known that the phosphate capacities of slags in equilibrium with liquid silicon are extremely lower. However, if we introduce another phase that possesses high ""phosphor capacity"" into the Si/slag system, one would expect to continuously remove P from Si through molten slag to the new ""phosphor capturer"". The so-called three-layer refming concept is thus proposed in the present study. Liquid Si and another liquid phase (Me) are separated by the molten slag spontaneously based on their different physicochemical properties. Two metal/slag distribution reactions are able to occur in the system simultaneously."

Jan 1, 2013

By A. C. Mollison

In November of 1983 a fire inside the autoclave caused the curtailment of operation of the Kidd Creek pressure leaching facility. Subsequent repairs and recommissioning of the autoclave in 1984 allowed Kidd Creek to increase its production of zinc as originally planned. This paper describes the operation of this process from 1984 to 1988 and details major mechanical work carried out on the vessel in 1.988:

Jan 1, 1990

By O. A. Ogunseitan

The contamination of aquatic ecosystems by mercury wastes is one of the most serious forms of environmental pollution associated with the metal mining and electrochemical industries. The transformation of inorganic mercury to alkylated species is a reversible bacterially-mediated process. The production of methylated mercury is of ?major public health and eco-toxicological concern because these forms of mercury are highly toxic ?and they bioaccumulate in aquatic organisms. We determined the response of the genetic determinants of mei:cury transrormation by Pseudomonas species (that predominate in contaminated soils and sediments), to the concentration and species? or available mercurfiations. By combining selective isolation and gene. ?probe techniques, the intrinsic genetic potential for mercury detoxification in a contaminated environment ?can be estimated. We determined that genetic units required for mericury volatilization (merA ?for mercuric reductase) are naturally amplified in response to mercury. Mercury-resistant bacteria that tolerate up to 100 ug Hg(Il)/ml of medium contain about 10 times more DNA fragments encoding merA than in unadapted bacteria. The exposure of bacteria to methylated.Hg (10 ug/ml lake water) produced increases (up to 10 times) in .genetic units, and higher levels of genetic expression (up to 50 times) per ml of lake water for the mercury reductase system, than on-induced lake water. The findings suggest that in environments where methylated Hg may accumulate as a result of bacterial activity, the reverse reaction which leads to the removal of mercury through volatilization from the system, may be achieved by inducing genetic ?amplification and expression of the mercuric reductase gene system.

Jan 1, 1991

By Emil B. Milosavljevic, Ljiljana Solujic

Cyanide is exceptionally reactive, and in typical gold/silver processing liquors, cyanide may be transformed into various species and forms depending on the mineralogy of the ore and chemical make-up of the process water. The exact speciation and relative concentrations depend on the Eh and pH values, as well as the free CN concentration in the system. Very good cyanide balances can be achieved by the judicious selection of the analytical techniques used. The choices an analyst has to make (which analytical methods to use and which ones to avoid) in order to gain better understanding of cyanide speciation and balances in a particular system under investigation will be discussed. Examples of cyanide balances obtained for the laboratory scale tests (agitated leach and column tests) will be presented and discussed.

Jan 1, 1999

By Kenji Monden

"The creep properties of tin-based lead-free solders Sn3.0AgO.5Cu and SnO.7CuO.1Ni and lead solders 10Sn90Pb and 50Sn50Pb were investigated at temperatures between 298 K and 398 K. The creep-rupture time decreases with increasing initial stress and temperature. The analysis of the solder creep curves uses the Omega method. The creep rate E is expressed by following formula: 1n ? = 1n ?0 + O?, where ?0 and O are experimentally determined. The parameter Eo increases with increasing initial stress and temperature. The activation energy for ?0 is 108 kJ/mol for Sn3.0Ag0.5Cu and 85 kJ/mol for SnO.7CuO.INi. These energies suggest that the lattice diffusion of tin is dominant. The energy of 1OSn90Pb is 37 kJ/mol and that of 50Sn50Pb is 67 kJ/mol. The creep-rupture time is calculated using the parameters, ?0 and O. The calculated creep-rupture time is in good agreement with the measured creep-rupture time.IntroductionLead-free solders are replacing traditional tin-lead solders as part of a major trend toward protecting the earth's environment. However, tin-lead solders are currently needed for a high temperature range. Since creep is the main deformation mechanism in solder joints, understanding a constitutive model for creep and examining creep data for solders are important for reliability analysis of solder joints. A steady-state creep equation is generally used for solders [1,2], and it supposes that the secondary-, or minimum-, creep rate occupies the entire creep life. However, secondary creep accounts for only about 15 % to 40 % of the entire creep life for solders. Thus, the equation may not represent the entire creep life."

Jan 1, 2012

By Zhang Yongzhu

Sulfoxides are one kind of extractants for precious metals. The structure, the coordination reaction, the extraction behaviour and the precious metals complexes of sulfoxides are summarized. The differences between sulfides, sulfoxides and sulphones are also discussed.

Jan 1, 1992

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By Tom W. Gonzales

Magma Metals Company commissioned a 3000 tpd Outokumpu flash smelting furnace in July 1988. Through September 1992 the PSP has smelted a first campaign record 4.1 million tons of concentrate. This paper discusses modifications made to the original process equipment to overcome design flaws as well as future design changes currently under consideration.

Jan 1, 1993

By T. Feldmann

Despite the ubiquity of applications for germanium, there is a lack of practically useful solubility data in acidic solutions. Previous studies were done at ambient temperature and only for commonly used acids (H2SO4, HCl). Hence, an investigation of the solubility of GeO2 in different acids was undertaken. Several inorganic and organic acids were studied in the concentration range of 1–11 mol/L and at 23, 40, and 60 °C. In the case of H2SO4 and HCl previous data was confirmed. Lower acidity resulted in a higher solubility for Ge at all tested temperatures. Tests done at 40 and 60 °C and low to moderate acidity levels, gave slightly increased solubility values at higher temperatures compared to 23 °C. This wasn’t the case at higher acidity levels, i.e., the solubility curves at different temperatures converge at high acidity. Lastly, a relationship of water activity and GeO2 solubility in different acid media was established.

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

In the last decades, authors have been focused in the development of a cyanide-free bath for the electroplating industry of brass due to the risks that involves the use of cyanide and they have been evaluated the electrodialysis as an alternativemethodforthetreatmentoftheeffluentgeneratedinthistypeofindustry because ofthe limitationscaused bythe chemical precipitation. Hence, thepresent paperaimedtodeterminethelimitingcurrentdensityoftheeffluentgeneratedinthe free-cyanide electrodeposition of copper and zinc using EDTA as chelating agent for the treatment of the effluent by electrodialysis. The synthesized solutions were preparedwith copper sulfate andzinc sulfate indifferent conditionsofpH (10–12) and proportion of cupric ions (30%, 50%, 70%). According to the results, the increase of pH and the cupric ions proportion caused an increase in the limiting current density because of the larger amount of anionic species in solution and the consequent difficult to achieve the concentration polarization phenomenon. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Guo Xueyi

The morphological characteristics of the nickel particles electrodeposited from chloride dominant aqueous solution was investigated. The effects of the electrolyte constituents, the parameters for the electro-deposition on the morphology of the nickel particles were addressed. It is evidenced that not only the particle size but also the morphology of the deposited nickel particles strongly depend on the electrolyte constituents and technical operation conditions. The electro-crystallization mechanism of the metallic nickel particles deposited at high current density was elucidated. The ultra-fine nickel particles with flake, nodular or dendrite shape may be produced by controlling the duration for electro-deposition.

Jan 1, 2003

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

Considering the risks involving the use of cyanide, other complexing agents have been evaluated for the treatment by electrodialysis of the effluent of brass electrodeposition and among them, EDTA is interesting since it has been already tested for many years to separate ions. The main objective of the present paper was to evaluate the occurrence of fouling and scaling on the surface of the anion-exchange membrane HDX 200 by the construction of chronopotentiometric curves and speciation diagrams in different conditions (pH between 10–12 and proportion of cupric ions of 30%, 50%, 70%). According to the results, the chronopotentiometric curves did not show additional inflexion points typical for the cases which occurs fouling and scaling for the pH values evaluated, which is in accordance with the speciation diagrams of the solutions constructed with the aid of Hydra-Medusa software. Hence, the pH and the proportion of cupric ions did not show influence on the curves behavior.

Mar 1, 2018

By R J. Singh, E. Z. Chacko, Devilal, S. K. Jha, Rina Sahu, Sheshank Shekhar

"Breakouts are one of the biggest problems encountered during continuous casting of steel billets. Billets get cracked locally or break completely in two parts during solidification causing the liquid part of the partially solidified billet to empty inside the cooling chamber. Proper control of important parameters is necessary to avoid break outs during continuous casting. In the present work, the nature of the break outs at a billet caster at Tata Steel was studied. Data analysis was also done for certain casting parameters and the Sulphur tracer test was conducted to understand solidification in the mould. It was found that to reduce the occurrence of break outs, it was necessary to tune the operations based on the grade being cast and the design of the mould tube being used.IntroductionA break out during the continuous casting process is a rupture of the partially solidified shell inside the secondary cooling chamber, causing the contained liquid steel to spill out. In the mid 1970s while continuous casting technology was still in early stage of development, causes of breakouts was not well understood. Today, with technological development much has been understood about breakouts but, most of the understanding has been in the slab casting process wherein due to the higher level of instrumentation, a lot of information has been gained. In billet casting however, due to the geometry of the mould housing with the tube mould, multiplied by the complexity of the multiple strands, instrumentation has not been used and obtaining data for analysis has been difficult.Breakouts at billet casters are still the main hindrances to production. A break out results in a loss in production since the strand which has had a break out is now not available to produce and thus a six strand caster would be reduced to a five strand caster, increasing the time for casting the same tonnage. Additionally extra set up time is required as more often than not a mould change is required in order to have the strand casting again."

Jan 1, 2014

By Masanori Abe, Yoshitaka Kitamoto, Kazuhiro Nishimura

"Ferrite plating is a chemical processing which utilizes Fe2+ - Fe3+ oxidation to synthesizing polycrystalline films of ferromagnetic spinels (MFe20 4, M = Fe, Co, Ni, Zn, Al, Cr, TI, etc:) directly from an aqueous solution at 24 - 100°C. This low temperature process allows us to fabricate new ferrite film devices on · substrates of such non-heat-resistant materials as plastics, GaAs integrated circuits, and biomaterials. Synthesized from an aqueous solution the ferrite plated ·films are highly biocompatible. Thus various magnetic device and biomedical applications have been proposed and realized using ferrite-plated films. Ferrite-encapsulated polymer microspheres are applied to antibody carries for enzyme immunoassay, and also to toners/carriers for photocopying. Perpendicular magnetic recording media utilizing plated CoNi ferrite films are proposed. The low-temperature synthesized films of NiZn and Co ferrites are potentially used as soft-magnetic and/or insulating layers, respectively at high/microwave frequencies.IntroductionFerrite plating is a processing which facilitates the formation of crystalline spinel ferrite films with various compositions, (Fe, M)30 4 (M = Fe, Co, Ni, Zn, Al, Cr, TI, etc.), directly from an aqueous solution at 60 - 100°C [1]. This opened the door to fabricating novel ferrite-film devices using substrates of such non-heat-resistant materials as plastics and GaAs integrated circuits [2-4]; conventional ferrite film preparation techniques such as sputtering, vacuum evaporation, MBE, LPE, etc., require high temperatures(> -600°C) for crystallization of ferrites, which deteriorates the non-heat-resistant substrates. Recently we extended ferrite plating to be preformed at room temperature [5, 6]. This enables us to use as substrates such organic materials as biomaterials (e.g. enzymes) having very low heat-resistance."

Jan 1, 2000

By Jonkion M. Font

An expression for the distribution ratio of arsenic between slag and copper matte or liquid copper was developed by both, an extension of the Reddy-Blander moderl for deriving a priori the arsenic capacity, and by a relationship between the arsenic capacity and the arsenic distribution ratio. In this study, the a priori arsenic capacities in the FeO-SiO2, CaO-SiO2,MgO-SiO2, FeO-CaO-SiO2, FeO1.5-CuO0.5-MgO-SiO2, FeO-FeO1.5-CuO0.5-CaO-Mgo and FeO-FeO1.5-CuO0.5-CaO-Mgo-SiO2, slags were calculated at 1573 K. The a priori arsenic distribution ratio between the FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slag and copper matte mn (Lx, )' and between the FeO-FeO1.5-SiO2 or FeO-FeO1.5-CuO0.5*-CaO-Mgo slag and liquid copper (Ls/cua) were calculated. The model calculated data are found to be in good agreement with the reported experimental data. The availability of reliable thermodynamic data for slag components and impurities in the slag-matte- metal system is essential for the accurate prediction of impurity capacities and distribution ratio data. The arsenic distribution ratio model developed here, can be extended for predication in multi-componet slags and mattes or liquid metal, and thereby may lead to the development of new slag systems for the efficient removal of arsenic in the copper smelting, converting and refining processes,

Jan 1, 2003