Search Documents

By Alexandre Bonan

This paper reports the results of a kinetic study on the oxidation of free cyanide and Cu-cyanide complex ions with HO,. The variables and respective ranges studied were the following: [CN] total =10 - 500 mg/l; pH=10-11; (H2O2/CN) mole ratio = 1- 3; (Cu/CN) mole ratio = 0.10 - 0.25. The results were interpreted by a semi-empirical model that incorporates the useful oxidation reactions and the parallel alkaline decomposition of H2O2

Jan 1, 1994

By N. V. Gorelikova

A new type of zirconium mineralization has been recognized in the Devonian volcanic rocks from an orogenic depression in the Central Kazakhstan. The most characteristic features of this deposit are the fine-grained nature of the zirconium mineralization, an unusual texture of the zirconium ores, and a close association of zirconium with phosphorus in the ores. Zircon grains form fine globular aggregates with the features of hexagonal crystal habit. In addition to crystalline zircon, the ores contain metacolloidal zircon, similar to hydrozircon. The morphological and textural features of the zirconium ores suggest that the deposition of ore deposits took place at a low temperature from colloidal solutions. It is believed that this deposit should be considered to be a new type of zirconium mineralization that is related to low-temperature hydrothermal processes.

Jan 1, 1995

By M. C. Ruiz

This work outlines the results of leaching studies on a copper concentrate containing chalcocite (Cu2S) and digenite (Cu9S5) with an acid saline solution of cupric chloride oxygenated at ambient pressure. The variables studied included the stirring speed, concentration of cupric ions, concentration of HCI, concentration of chloride ions, oxygen flow rate, temperature and time. The leaching system was found to be very effective for the dissolution of the concentrate. Over 95% of the copper was dissolved in 30 minutes with negligible dissolution of iron. The dissolution of copper increased with the stirring speed up to about 400 rpm and depended little on the total chloride concentration. The oxygen flow rate affected the dissolution of copper only below 0.1 1/min. The concentration of HC1 did not influence the dissolution providing its was sufficient to avoid the precipitation of copper oxychloride. The study of the effect of the temperature showed a maximum in copper dissolution around 90 "C

Jan 1, 1997

By Zhijing Zhang

Long-term thermal stability of ionic liquids is essential for reliable performance of ionic liquids in any engineering applications. TGA studies were carried out on a series of ionic liquids with different cations and anions such as 1-butyl-3-methylimidazolium chloride ([C4mim]Cl), 1-hexyl-3-methylimidazolium chloride ([C6mim]Cl), 1-hexyl-3¬methylimidazolium tetrafluoborate ([C6mim]BF4), 1-hexyl-3-methylimidazolium hexafluorophosphate ([C6mim]PF6), 1-octyl-3-methylimidazolium hexafluorophosphate ([Csmim]PF6), and 1-butyl-3-methylimidazolium bis(trifluromethanesulflonyl)imide ([C4mim][Tf2N]). The short-term thermal stability of ionic liquids was evaluated by measuring the onset temperature of decomposition of ionic liquids, and the long-term thermal stability of ionic liquids was also evaluated by weight loss of ionic liquids over a long period of time at various temperatures. The experimental results showed that the long-term thermal stability of ionic liquids decreased with increasing temperature and was significantly lower than the onset temperature of decomposition of ionic liquids.

Jan 1, 2002

By M. Sakamoto, S. Karaswa, Y. Yoneoka, Y. Ohmizo

"The Annaka Refinery has been processing leach residue by Waelz process for 17 years. Recently, the quantity of the leach residue has increased due to a decline in the quality ~f zinc concentrate. Meanwhile, negative factors (e.g. deterioration of water balance due to improved electrolytic power consumption rate) have increased· in the processing of the leach residue.We have implemented various measures in responses to this situation, while striving to increase ·processing capacity and achieve stable operation. AS we have largely completed our assessment of the efficacy of these measures, we report on our recent process improvements.IntroductionWe have been treating leach residue by the Waelz kiln process since 1981. At that time, treatment of only 50,000 tons of leach residue per year was anticipated. However, subsequent process improvements have revised this figure up to 75,000 to 80,000 tons per year.However, today's increased Fe zinc concentrate grade has resulted in increased amounts of leach residue. In addition, improvements have reduced electrolytic power consumption rate of zinc electrolysis, limiting the amount of water that can be used in ·the zinc refining processes and for deaning leach residue. Consequently, we encounter an increasing number of problems and factors adversely affecting leach residue treatment, including increases in water-soluble Zn (WsZn) and. S (S04) in leach residue.To solve these problems, we have taken several measures to ensure long-term continuous operation and treatment of this increased · amount of leach residue. This paper discusses these measures."

Jan 1, 2000

By E. Oshima

The only one reverberatory furnace smelting in Japan has been alive in Onahama Smelter, Onahama Smelting and Refining Company. The fuel for the reverberatory furnaces had been changed from bunker C-oil to mainly coal and partially waste tires to reduce the energy cost. The steam, recovered by the waste heat boilers of the reverberatory furnaces, has been utilized fully for the power generation to save the purchase power. Copper concentrate has been smelted also by injection through tuyeres in the P.S. converters since 1983. The amount of concentrate, treated in the converters, was increased by the construction of small oxygen plant in December, 1990. In the paper, the current practice and improvements in the reverberatory and converter operations are described.

Jan 1, 1993

By Jianhua Xin, Min Chen, Cuihuan Huang, Shan Yu, Xiaoao Li, Nan Wang, Guanghao Chen

Copper enrichment behavior in continuously cast slab induced by scale formation after continuous cooling in H2O vapor atmosphere and consecutively in air has been experimentally investigated by combining with SEM-EDS analysis, for the purpose to examine the effects of initial slab surface temperature and contents of copper and nickel. For Slab 1 with copper content of 0.1 percent, no visible copper enrichment is found at scale-substrate interface irrespective of the various scale microstructures formed at different initial slab surface temperatures. For Slab 2 with higher contents of copper and nickel, copper-rich phase accumulates and stays at scalesubstrate interface under the condition of lower initial slab surface temperature; while Cu-rich phase in the porous scale formed at higher initial slab surface temperature is noted with simultaneous Ni-enrichment appearing in front of the steel-scale interface. Both a porous scale and high nickel content work together to provide pores for copper-rich phase migration away from interface and occlude within the scale layer.

Jan 1, 2016

By Virgil Optasanu, Yvon Lacroute, Eric Lesniewska, Tony Montessin, Pauline Vitry, Eric Bourillot, Cédric Plassard

A general challenge in metallic components is the need for materials research to improve the service lifetime of the structural tanks or tubes subjected to harsh environments or the storage medium for the products. One major problem is the formation of lightest chemical elements bubbles or different chemical association, which can have a significant impact on the mechanical properties and structural stability of materials. The high migration mobility of these light chemical elements in solids presents a challenge for experimental characterization. Here, we present work relating to an original non-destructive, with high spatial resolution, tomographic technique based on Scanning Microwave Microscopy (SMM), which is used to visualize in-depth chemical composition of solid solution of a light chemical element in a metal. The experiments showed the capacity of SMM to detect volume. Measurements realized at different frequencies give access to a tomographic study of the sample.

Jan 1, 2015

By Vinicius Alves Gomes, Jean Igor Margem, Frederico Muylaert Margem, Sergio Neves Monteiro, Marina Rangel Margem

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and, consequently, affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of malva fiber in epoxy matrix composites. A small critical length was found for the malva fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2015

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the fum ace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By B. Sereda

As it is known the creation and development of new titanic alloys has been problematic up to now. They can be used in aircraft and vehicle construction, shipbuilding and as materials for keeping static loadings in high-temperature environments. In this work the synthesis of various titan aluminides is investigated. Mathematical model of structurization process was done. On the base of retrieved model the mechanisms of structurization in systems Ti + Al and Ti + 3Al was determined. Experimental researches were done at two different modes: burning and thermal spontaneous ignition. The method of retrieving compacted products combusted in SHS conditions (SHS-compacting) was used to gain these intermetallic compounds. The physical and thermal characteristics of technological process and their influence on structurization, homogeneity of structure and porosity of titan aluminides have been simulated and researched. It is established that the SHS-compactizing technology is fully capable of supervising the process of structurizations with the whole complex of advantages and can be applied for receiving qualitative titan aluminides with the set of chemical-physical properties.

Jan 1, 2010

By Qiang Zhong, Qian Li, Yongbin Yang, Tao Jiang

Thermogravimetric analysis (TGA) has been used to research the pyrolysis and combustion processes of coal used in rotary kiln of iron ore oxide pellet. Furthermore, the effects of air flow and oxygen concentration on the combustion behavior of coal were examined with TGA. The results showed that two individual stages can be distinguished for the pyrolysis of coal, the water evaporation stage and the de-volatilization stage. And the information on ignition and burnout characteristics can be obtained from the combustion process analyzed by TGA. Large air flow almost has no effect to the combustion process except that it enhances combustion intensity. However, the combustion process is further accelerated under oxygen-enriched conditions. With all experimental results, it could provide an attractive approach of analyzing coal for the rotary kiln process.

Jan 1, 2016

By Naixiang Feng, Kun Zhao

This work presents a two-stage aluminothermic reduction process for preparing Ti and Ti-Al alloys using Na2TiF6. Al-Ti master alloy and pure cryolite as co-products could be obtained. After the first stage reduction, the oxygen content of the metal product is reduced, and the second stage produces high-purity titanium or Ti-Al alloys with cryolite and Al-Ti master alloy as recyclable co-products.

Mar 1, 2017

By Shigeru Ueda, Shin-ya Kitamura, Shohei Koizumi, Xu Gao

Steelmaking slag was confirmed to be a useful fertilizer for paddy growth as it efficiently supplies Ca and Si to soil water. In addition, supplement of Fe from slag fertilizer has been expected to suppress the H2S generation in paddy soil, especially for the degraded paddy soil. However, on the basis of our previous research, the Fe dissolution ability changed with slag brands, and even some brands could dissolve Fe under paddy soil pH, the supplying ability were not high. To improve Fe dissolution, we found that among various kinds of Fe-rich mineralogical phases in slag, the CaO–SiO2–FeO glassy phase showed highest water solubility of Fe. Because the CaO–SiO2–FeO glassy phase was a quenched molten phase, its dissolution behavior may depend on chemical composition, and this is important for controlling slag composition to produce fertilizer which can easily release Fe. Therefore, in this research, the CaO–SiO2–FeO glassy phase of various CaO/SiO2 ratio, Fe2+/T–Fe ratios, and FeO contents were synthesized, and the dissolution behaviors of Fe as well as other cations from these synthetic glassy phases into an aqueous solution at pH of 5 were investigated. The result showed that the dissolution ratio of Fe increased significantly by increasing Fe2+/T–Fe ratio. An increase in FeO content of glassy phase also increased the dissolution of Fe. In addition, the Fe dissolution ratio showed a local maximum with increasing CaO/SiO2 ratio.

Mar 1, 2017

By I. Moscoso, R. Padilla, M. C. Ruiz

Antimony and arsenic are impurities in copper concentrates found normally as stibnite (Sb2S3), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4). When copper concentrates contain appreciable amounts of As and Sb, they must be removed before smelting to avoid environmental pollution. Oxidizing volatilization roasting at 500–700 °C has been used to eliminate these impurities. However, only a fraction of Sb volatilizes in those conditions; thus, a more effective process to eliminate antimony from concentrates is needed. In this study, the chloridizing roasting of Sb2S3 using CaCl2–O2 was investigated to remove the antimony from concentrates. XRD analysis of calcines indicated that the overall reaction could be written as: Sb2S3 þ3CaCl2 þ6O2 ¼ 2SbCl3 þ3CaSO4 Temperature and oxygen partial pressure have a significant effect on the rate of reaction. An estimated conversion of about 90% was obtained at 750 °C, 5.4% oxygen in 20 min. High oxygen concentrations arrest the advance of the reaction forming various antimony oxides including Sb6O13, Ca5Sb5O17 and Sb2O4.

Mar 1, 2017

By Xun Zhang, ZhiLong ZHAO, Lifeng Zhang, Huiqing Tang

A two-dimensional gas-solid model has been developed for examination of the blast furnace (BF) performance under hot charge operation. Simulation conditions were obtained from the actual operation conditions of the BF with inner volume of 2500 m3 and molten iron output of 6250 ton hot metal (THM) per day. The simulation results indicate that hot charge operation could change the thermal state of the BF in the region above cohesive zone (CZ) and has little influence on the thermal state of CZ zone and the region below CZ; it could intensify both the indirect reduction of the ore and the gasification of the coke in the region above the CZ. The optimum temperature for hot charge operation is 750 K, under which, a coke rate reduction of 25 kg/THM could be obtained.

Mar 1, 2017

By Mansoor Barati, Leili Tafaghodi Khajavi

"This study involves employing solvent refining as a purification process in which silicon recrystallization takes place from an iron-silicon melt. It is believed that iron will act as the impurity “getter” and purified silicon crystals will grow from the alloy melt, while the impurities are segregated to the liquid alloy. Phosphorous is a problematic impurity to remove since its segregation coefficient in pure silicon is relatively large. To assess the feasibility and efficiency of phosphorous removal through solvent refining, it is critical to study its equilibrium distribution between solid Si and the Fe–Si alloy phase.The distribution of phosphorous between solid silicon and iron-silicon melt at 1210-1310 °C was measured to evaluate the impurity removal potential of each alloy. Interaction parameter between phosphorous and iron was calculated by varying the concentration of phosphorous in silicon.IntroductionAmong various semiconductor materials for manufacture of solar cells, silicon accounts for over 90 percent of today's PV materials [1, 2].The major challenge in producing solar silicon that operates efficiently is to meet purity level requirement through a cost efficient route. Silicon solar cells can play a significant role in answering the world's need for energy if cost reductions can be achieved through manufacturing process. Considerable effort has been made to replace the expensive, complex vapor-phase purification by a simpler and less costly process. One of the refining approaches that have attracted wide research interests is producing low-cost solar grade silicon by purification of metallurgical grade silicon. Since metallurgical processes are selective in removing impurities, a combination of various purification processes can be used to reduce the impurity level in silicon. Considering different thermodynamic characteristics of impurities, each refining step is responsible for lowering specific impurities."

Jan 1, 2012

By Alexander I. Raitchenko

"Although one takes into account only thermal expansion usually at analysis of convection onset, the essential factors include magnetic and electric fields. If Lorentz-force originating from intercrossed electric and magnetic fields' action is directed downwards its effect strengthens gravitational action, and value of critical Rayleigh number (limit value for convection onset) must decrease; increasing of critical Rayleigh number should be observed in case of Lorentz-force directed upwards. Extent of such an influence is determined by relation of Lorentz-force to hydrostatic head in gravitational field. Competition between electromagnetic force due to nonuniformity of electroconductivity (on account of its temperature dependence) and electromagnetic buoyancy force may have ambiguous effect: both increase or decrease of critical Rayleigh numbers. Proposed conception is applicable to analysis of situations in liquid conductors and conductive gases.IntroductionStatic or dynamic situations in fluid media are determined besides properties of these media by a variety of external influences. However one correlate~ the onset of the convection and its development with influences of the minimum quantity of external causes frequently. Most known and usual factors are the gravitational and temperature fields. The number of processes includes heat generation in media volume, and theoretical analysis in these cases takes into account this interior heating together with boundary temperature conditions. But explanation of many natural and technical events is not complete and cogent within limits of thermo-gravitational terms. The whole complex of acting factors which influence convective processes in techniques and nature is greater in many cases. In particular the action of · electromagnetic nature often has not less importance than gravitation one. Stability or instability of a current layer in the plasma must be determined by non-uniformity of electroconductivity owing to non-uniformity of temperature [1]. The presence of Joule dissipation in the plasma through which the electric current flows stipulates initiation of origin of overheated instability [2]. It is known that electroconductivity of arc in the boundary zone changes sharply with radial distance [3], and this must influence its stability essentially. If the intercrossed electric current and magnetic field begin to act on an electroconductive fluid besides the non-uniform temperature field and the gravity, the conditions for the onset of the convection change radi- . cally: both the temperature field and their solutions have to be changed also. The analysis of equilibrium single-time correlation functions of fluctuations must be employed for situations with enlarged number of factors as this was in case for the Rayleigh-Benard problem where the object is a horizontal layer of liquid. This can be carried out by taking into account the detached forces' correlations [ 4, 5]"

Jan 1, 1999

By W. D. Cho

Fast dissolution of nonmetallic inclusions such as alumina particles in molten slags has been required in secondary steelmaking -ladle and tundish - to minimize the amount and the size of nonmetallic inclusions in steel products. In the present work, the dissolution behavior of alumina particles in molten CaO-A12O3 and CaO-A12O3-SiO2 slags at the temperatures between 1450 and 1550°C have been investigated in terms of kinetics and mechanism. Alumina particles were added directly into the slags and the variation of the particle size with time was determined using optical and electron microscopies. The conventional types of slag for ladle and tundish were included in the dissolution study. The effects of Al2O3, Siq, CaF2 and MgO contents on the dissolution rate of alumina particles have also been determined. The diffusion boundary layer between alumina particle and bulk slag phase has been observed and analyzed using SEM and EDS. Based on the analysis of kinetic data and the boundary layer, the dissolution mechanism has been discussed.

Jan 1, 2002