Search Documents

By M. Hashiuchi

In 1972, the tankhouse of the Tamano Smelter adopted a high current density electrolysis operation applying the PRC (Periodic Reverse Current) method. In 1994, the phase four production expansion project, which incorporated significant re-structuring of the organization, was completed and we have achieved an annual production capacity of 191,000 tons. The target of this project, the production capacity, was increased by 1'8% and labor productivity by 25%. After the expansion, some improvements in the starting sheet section and the verticality of the electrodes were carried out, and the efficiency of the operation was greatly enhanced, including the improvement of the quality of the electrolytic copper.

Jan 1, 1999

By M. Arenas

A corrosion study of a bonded NdFeB permanent magnet materials alloyed with titanium carbide additions has been undertaken. The materials were produced by rapid solidification by melt spinning. Commercial epoxy was used as a bonding medium. The corrosion results were compared with those of a near stoichometric unalloyed NdFeB. Anodic polarization and potentiostatic techniques in 0.9 M Na2SO4 solutions were used to characterize corrosion behavior. It was found that the addition of 6 a10 Tic resulted in superior corrosion resistance, as indicated by lower corrosion currents and less iron dissolution at fixed potential.

Jan 1, 1997

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

By Donald R. Sadoway

Fused salt electrolysis is used extensively in the primary extraction of metals (electrowinning), in the refining of metals (electrorefining), and in the formation of coatings (electroplating). In the case of rare earths, fused salt electrolysis competes with nonelectrochemical processes to make the same products. However, fused salt electrolysis has the potential to produce these metals in a variety of technologically useful forms: thin films and epitaxial layers, powders, and a variety of nonequilibrium structures. The theory and practice of fused salt electrolysis as it applies to the extraction, refining and plating of rare earth metals are described. The potential of fused salt electrolysis to synthesize advanced materials containing the rare earth elements is assessed.

Jan 1, 1989

By R. Cheng

The kinetics of the solvent extraction of ythium from HCl solution with mono-2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester (HEHEHP) have been studied using a rotating diffusion cell (RDC). The effects of rotation speed, pH, ymium and extractant concentrations and temperature on the rate of extraction were examined. The rate of extraction of ythium appears to be controlled by an interfacial reaction of metal ion and extractant. The concentration of the latter is determined mainly by diffusion through the membrane. The contributions of the rates of diffusion in the diffusion layer, diffusion in the membrane and chemical reaction at the interface to the overall rate have been calculated on the basis of a kinetic model.

Jan 1, 1992

By V. Ramachandran

ASARCO Incorporated, a large and diverse producer of non-ferrous metals, is involved primarily in smelting and refining of copper and lead. The Company also recovers by-product metals and chemicals produced in the smelting and refining process including selenium, tellurium, silver, gold, platinum, palladium, bismuth, antimony oxide, lead-antimony alloys, and nickel sulfate. The treatment of complex concentrates, containing high level's of impurities, also results in the production of various sludges, drosses, dusts and slags. This paper addresses the interplant and intraplant transfer of these materials between the copper and lead circuits and their subsequent treatment for maximum metals recovery. It also describes the role of ENCYCLB/TEXAS Inc., a subsidiary of Asarco, which treats Asarco's by-products, as well as hazardous and non-hazardous wastes produced by other manufacturers.

Jan 1, 1994

By W. F. Miao

Nanocrystalline mixtures of Nd2Fe14B and a-Fe have been synthesized by mechanical milling and heat treatment. The samples exhibit isotropic behavior, with significant remanence enhancement associated with exchange coupling across the interfaces of hard and soft magnetic phases. Measurements of the effect of heat treatment on structure and magnetic behavior demonstrate the important influence of grain size on magnetic properties. The effect of alloy additions to increase the saturation magnetization of the soft phase and the magnetocrystalline anisotropy of the hard phase has also been investigated.

Jan 1, 1997

By V. M. Paretsky

Recent developments made in the Gintsvetmet Institute in the field of autogenous smelting processes have confirmed that autogenous smelting continues to be the main prospective technology for pyrometallurgical processing of sulfide raw materials. This technology ensures energy conservation and environmental safety conforming to the current world standards for production of heavy non-ferrous metals. Two alternative processes of single-stage autogenous smelting producing white metal as well as high-basic ferrite-calcium slags have been developed and can be recommended for technical modernization of Russian copper smelters.

Jan 1, 2002

By L. Salinas

Lance injection of gas and particles into a molten bath is currently practised in metallurgical processes (Mitsubishi lances for example). Several experimental and theorical studies have been conducted in the past on this topic. However, neither detailed calculations nor experimental studies of local flow patterns have been published. In the present work, a numerical simulation of the interaction of a gaseous vertical descending jet and a liquid surface was done, using the turbulence k-e model. There is a fair agreement between the calculated and the experimental values. The results of this study demonstrate that it is crucial that the gas jet velocity profile and turbulent characteristic are correctly formulated in order to correctly simulate the system.

Jan 1, 1999

By E. M. Alcântara

This paper describes some aspects about the relationship between copper electrorefining addition reagents and the hydrogen in the cathode. The conditions of electrorefining were studied by factorial design methods. The advantages of this technique are reduction in the number of tests, well organized experiments; improvement in productivity and reliability of results. The dosage of the two main addition agents, glue and thiourea, were varied simultaneously and compared with the hydrogen content in the cathode. The influence of these factors, as well their interactions were analyzed by statistical methods denominated ANOVA (Analysis of Variance). The increase of thiourea quantities, within of levels studied, influenced significantly at 95% confidence in the hydrogen content in copper cathode.

Jan 1, 1999

By Admire Chaendera

A gas jet was blown through submerged nozzles to stir the bath in the presence and absence of slag. Mixing and mass transfer rates were then studied. Water and kerosene (10% by volume) were used to simulate the metal and slag phases respectively in the cold model. The mixing time (Tmix), defined at 99.66% bath homogeneity level, increased with bath height and decreased with an increase in the gas injection rate. Its value in the model vessel was related to gas flow rate (Q), bath weight (W), and bath height (H) by, Tmix = 4.39Q-0.73W0.24H1.12. Inclusion of the slag phase increased Tmix by about 16% and the mass transfer parameter, [(Reloc,r)0.25(Ret)0.32], values by about 32%. Mass transfer rates were higher near the bath surface and in the gas-liquid plume region. They increased with gas flow rate but decreased with an increase in bath height. The relationship, K Q0.08, showing derived mass transfer coefficient (K) dependence on the gas injection rate (Q) was established. The proportionality constant in the equation varied with gas flow rate and sample location.

Jan 1, 2006

By M. Kawakami

In the blast furnace, the reduction of iron oxide and gasification of coke occur simultaneously. It is well accepted that the gasification reaction controls the simultaneous reaction. Therefore, it is important to develop highly reactive carbonaceous materials. It is also known that the reaction is accelerated catalytically with the addition of some materials. In the present work, the catalytic effect of iron, nickel and CaO on the gasification of graphite and coke was examined. The catalytic effect of iron, nickel and CaO on the reaction rate of graphite was noticed The effect was larger at lower temperature. At 1373 K, the effect almost vanished. The effect was larger in the order of CaO, iron and nickel. The reaction rate of de-ashed coke increased by the addition of iron and nickel. The effect of iron was larger than that of nickel. The effect was larger at higher temperature, which was contrary to the case of graphite. The reactive surface area increased also by the addition. Therefore, the catalytic effect on reaction rate might be attributable to the increase in the reactive surface area.

Jan 1, 2006

By Akram Salah Eddine Belaidi, Lakhdar Azzouz, Benchaa Benabed

"The dunes sand is a material of a large availability in Algeria. This material is practically unexploited. The introduction of this material as a new element in the construction can be more relieve the domain of building, and contribute to the development of the southern regions of Algeria, which are very rich in this material. The main objective of our work is to exploit a largely available material in the Algerian south which is the dunes sand, as a material of construction in the region of Laghouat.In this study, first we investigated the effect of the curing environment and the nature of the sand on the mechanical properties of the mortar, such as; flexural and compressive strengths. Then after, we studied the durability of the mortar under cycles of wettingdrying and the chemical attack of sodium sulfate (Na2SO4 5%).According to the results, we note that the mortar of the sand mixes (river sand plus dunes sand) present the best mechanical performances under different environment of curing. In addition result of durability studies put forward that the mortar of the sand mixes is more resistant to the sulfates attack."

Jan 1, 2008

By J. H. Lee

LG Metals Corporation started its second smelter operation at Onsan along with the existing flash smelter on January 31, 1998. Onsan smelter has been producing about 140,000 tons of copper annually from concentrates with the flash smelting line since 1979. In accordance with an increase in domestic copper demand, LG Metals Corporation decided to expand smelting and refining capacity by introducing a second smelter line using the Mitsubishi continuous process and a new tankhouse in 1995. After two years' expansion works consisting of engineering, procurement, construction and a successful commissioning test, the total smelting capacity of Onsan smelter increased to 340,000 ton of copper annually from concentrates. This paper describes the smelting facilities, operation result, problems encountered and improvements during the start-up and early operation of Onsan's new smelter

Jan 1, 1999

By Nickolas J. Themelis

The role of copper in the economy will not diminish in the 21st century. Following the tenets of industrial ecology, production and use of copper must take into account both human needs and also how to minimize "collateral" effects on the environment. Dispersive uses will be phased out and post-use recovery of copper will increase. This will result into an advantage for smelting processes that can accommodate mixed metal scrap and waste streams. The bath smelting processes of Noranda and Mitsubishi will continue to make progress but the dominance of the Outokumpu flash smelting will not be challenged until the Noranda reactor overcomes the obstacles to the direct production of copper, thus eliminating the need for a converter.

Jan 1, 1999

By G. Ríos

Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975 the old blast furnaces were replaced by the Outokumpu FSF technology. During the last 30 years, through several expansions and technical modifications, the production has increased up to 300,000 tpy of new copper. This paper describes the developments on the control of impurities that have been made to fit new situations, such as a new artificial gypsum plant, a new electrolyte treatment plant or different secondary materials handling management.

Jan 1, 2006

By M. D. Bishop

Loss of organic solvent extraction circuits occurs through several accepted methods. Losses are commonly attributed to entrainment of the plant organic and evaporative loss of diluent. Evaporative losses of diluent have been estimated using various models or by considering all losses over and above entrainment to be due to evaporation. Other possible loss mechanisms are discussed and data on losses during weather conditions are presented. Accurate estimation of evaporative loss is vitally important to the industry due to both cost factors and environmental concerns. Data for and description of the Diffusive Flux Model are presented as an improved-method of estimating evaporative losses:

Jan 1, 1999

By Andrey Dmitriev

The solution of set of equations for the bottom zone presented by a condition of a thermodynamic equilibrium, namely, an equilibrium constant of wustite reduction by carbon oxide, material and thermal the balances, supplemented by the equation of the heat balance for the top zone, allows to calculate the base indices of blast furnace smelting. The calculated indices are extreme accessible at the given parameters of charge and blast. Application of actual degrees of the use of gas instead of equilibrium allows the calculations of actual indices of the blast furnace smelting process.

Jan 1, 2006

By M. Ramprecht, M. Wu, A. Kharicha, A. Ludwig, H. Holzgruber

"The influence of the frequency of AC power supply on the magneto-hydrodynamic during the electroslag remelting process is studied. The focus is on the electrodynamic field and its resulting mechanical effects on the flow and liquid interfaces. The possible influence of the electrochemistry on the droplet formation is qualitatively discussed.IntroductionThe electroslag remelting (ESR) process is a secondary melting technique which can be used for a variety of metals and alloys, provided appropriate fluxes (slags) and melting parameters are employed. The ESR process is presently operating mostly with AC current of about 50 Hz. However for reasons primarily of inductive losses in the electric circuit, furnaces for ingots larger than 1 m, use or are projected to use current of very low frequency (< 5 Hz). Effects of lower frequencies (2.5-5Hz) on macrostructure and non-metallic inclusions were recently studied by Chang [1]. Most of investigations were performed either with DC power or with AC of 50-60 Hz [2-4]."

Jan 1, 2012

By Michael J. Virnig

The formation of crud is a normal part of operating a solvent extraction circuit for the recovery of copper. It periodically must be removed from the circuit. This results in significant costs in terms of manpower, downtime, and loss of circuit organic. Field studies have been carried out that show that the presence of a thermodynamic modifier in the organic phase contributes to crud formation. In an effort to better understand what factors contribute to crud formation, laboratory studies involving competitive adsorption studies with model solids have been carried out. The results of these laboratory studies will be integrated with the results of the field studies to present a better understanding of crud formation.

Jan 1, 1999