Search Documents

By L. Lewczuk

A detailed mineralogical and liberation study was performed on the iron ore mill products from the Scully concentrator of Wabush Mines, Newfoundland. Automated image analysis techniques were applied to deter-mine grain size distribution and liberation of all mineral components of the ore. As a result of the study it was indicated that iron recovery can be improved and the Mn minerals reduced in the iron ore concentrate by (a) increasing spiral middlings, (b) regrinding the middlings, and (c) separating the Mn minerals from the iron minerals in the reground middlings.

Jan 1, 1988

By Liyuan Chai

The corrosion mechanism of A3 steel induced by chloride ions in the purified water had been investigated with the A C Impedance technique. The results showed that there were another two factors which determined its electrochemical corrosive rate: the electrode potential and coverage ratio of chloride ions on the surface of A3 Steel. The corrosion mechanism of A3 steel in the solution with chloride ions emendation was two steps of electrode process with the rate-determining step of 0,32kFeClFeCle+--¾¾®++.

Jan 1, 2009

By Dianyuan Dang, Guihong Han, Wenjuan Wang, Tao Jiang, Yanfang Huang

In this study reduction kinetics and swelling behaviors in "two-step process” were investigated by weight-loss technique and visualizing physical changes of pellet. Results showed that reduction degree (r) increased with increasing temperature and time. According to the dynamic calculation, when reduction temperature was lower than 1000°C the reduction process was controlled by chemical reaction with apparent activation energy of 72.27 kJ/mol. When reduction temperature was higher than 1000 , the equation of t/[1-(1-r)1/3] against [1+2(1-r)-3(1-r)2/3]/[1-(1-r)1/3] followed straight lines, demonstrating that reduction was mixed-controlled. Swelling experiments indicated that the maximum swelling index increased with the increase of reduction temperature and CO content.

Jan 1, 2016

By H. K. Lin

Thermodynamics of Cu-C1-H2O system and the kinetics of copper dissolution in cupric chloride solution were studied with emphasis on possible difficulties which may occur during copper electrowinning. E,-pC1 diagram of this system wasestablished. Equilibriumdistributionof various copper chloride complexes of different valent states at the presence of metallic copper was computed through the relations of the simultaneous equilibria. The mechanism-of copper dissolution in the cupric chloride solutions was proposed and the mechanism of copper electroposition was discussed. The researched results were used for guiding the investigation of copper electrowinning from cupric chloride solution.

Jan 1, 1991

By P. H. Chang, J. E. Gould

"Solidification structures and austenite decomposition in some spot welded O.05%C - O.3%Mn steels have been studied with the aid of a numerical thermal model. The model is a one dimensional finite difference formulation, and accounts for melting, temperature dependent thermal properties, effective heat transfer in the liquid, and contact resistances. The model was used to predict solidification conditions during resolidification of the nugget. These solidification conditions were correlated with the primary dendrite spacing using available primary dendrite spacings modelling. The model was also used to predict cooling rates in the temperature regime for austenite decomposition. These cooling rates were used to interpret the underlying microstructure.INTRODUCTIONThe metallurgical transformations which occur during the spot welding of low carbon steels have traditionally been characterized only in the most general of fashions. This is most probably due to the similarity of spot welded microstructures to other welded microstructures, and that the mechanical integrity of spot welds has not been a concern. In addition, little information about the particular thermal cycles experienced during spot welding has been available. The introduction of HSLA (microalloyed) sheet steels has, however, raised new concerns about the integrity of spot welds. These steels have on occasion shown irregular weldability, as well as brittleness in the weld nugget on destructive testing l - 4 .In response to these concerns, considerable work has been done attempting to characterize thermal cycles in spot welds 5-12. This has largely taken the form of thermal modelling, with the end purpose generally to estimate the size of the nugget formed. This work uses the thermal model developed at Inland Steel 13 ,14 to try and understand, in a more fundamental way, microstructural evolution in spot welds. Two facets of this microstructural evolution are examined in detail:"

Jan 1, 1986

By Fumitaka Tsukihashi

Increasing amounts of steel scrap are being used as resources for steelmaking. Therefore. there has been a growing interest in the removal of handful tramp elements such as antimony, zinc, tin, arsenic, bismuth, lead and copper from the molten steel. The problem that should be solved is the economic removal treatment of residual tramp elements in the steelmaking processes and the production of high quality steel by reducing the effect of the contaminated tramp clements and satisfying the environmental regulations. In this paper, the available thennodynamic data of the residual tramp elements in the molten steel are summarized and the possibility of the removal of residual tramp elements from the molten steel is thcnnodynamieally estimated.

Jan 1, 2003

By Masayuki Kudoh, Tohru Maruyama, Yohichi. Ito

When hypo-peritectic carbon steel is quenched during unidirectional solidification, the region of fine columnar grain is observed. It is classified into two coexisting phases. One is coexisting phases of liquid, delta and gamma in the upper part of the region, and the other is coexisting phases of delta and gamma in the lower part of the region. To form the coexisting part of the three phases means that solidification in this experiment proceeds in non-equilibrium state. The size of the narrow side of one fine columnar grain coincides with the arm spacing of a primary dendrite and this result is the same as the hyper-peritectic carbon steel. However, the boundary of the fine grain in the hypo-peritectic carbon steel is formed in different location from that of the hyper-peritectic carbon steel. The former is formed in the skeleton of the dendrite, while the latter is formed in the interspacing of the dendrite. The region of the fine grain changes suddenly to that of the coarse grain when the delta phase in the coexisting part of two phases disappears completely. Therefore, the delta phase in the hypo-peritectic carbon steel might prevent the growth of gamma grain. In order to recognize it, ferrite formers such as Mo, V and Ni are added in the sample. Then, the longitudinal length of the fine columnar grain extends in the sequence of the no addition, Mo, V and Nb.

Jan 1, 2000

By P. K. Narasimhargahavan

This paper discusses briefly the major reasons associated with the growth and its impact on the energy requirement and Environmental imbalance. A projection based on the present global Alumina and Al requirement indicate a substantial further growth of at least 30% over the next 10 years. It is indicated that the main factors which are likely to influence investments are the environmental factors such as the Climate Change and global response to the growing energy prices and sustainable development. Each of the developed / developing nations must find response to the GHG emissions which will encourage the Al Industry to make an effective contribution to global warming while preserving the international competitiveness of the industry - a challenging task. The efforts shall concentrate on improving energy efficiency in the industry possibly of the order of 25% over the next 10 to 20 years. The developments in this line are discussed.

Jan 1, 2010

By Gretel Parker

In situ Raman spectroscopic investigations of copper iron sulfides in leach solutions have been undertaken. Coupling potentiodynamic techniques to Raman spectroscopy produces a powerful tool for studying mineral surface response to changing conditions, while ESEM and high-vacuum techniques provide complementary ex-situ information on surface structure and composition. Oxidative acid leaching of chalcopyrite at ambient temperature yielded a product with S-S bonds that were shifted from those seen with covellite, with little evidence of elemental sulfur formation. Leaching of chalcopyrite led to non-homogeneous product distribution. Raman spectroscopy was able to identify the products formed on the mineral surfacein situ while leaching was occurring. Raman mapping and imaging demonstrated a surface distribution of the products which can be related to composition and structure changes of the mineral surface. The surface formed on chalcopyrite after anodic oxidation at 0.570 V vs. Ag/AgCl in 0.1 mol dm-3 HCl undergoes laser-induced transformation.

Jan 1, 2003

By Antonio Martin, Jesus Hurtado, Francisco Jimenez

"Atlantic Copper is one of the largest copper producers in Europe. Its production facilities, including a primary copper smelter and an electrolytic refinery, are located in Huelva, on the southwest coast of Spain. These installations enable the smelting of over 1 million tpy concentrates to produce up to 260,000 tons per year of cathodes and 900 ktpy of sulphuric acid.Since 1970, several improvements have been made at the Converters Area such as modifications of primary hoods, operations with an OPC system, installation of scrap chargers, the recent installation of the secondary hoods and other environmental projects. All these modifications have been aimed at increasing the capacity of our smelter while keeping our continuous environmental commitment.This paper describes the modifications and improvements carried out at the converters area and our proposals for future developments."

Jan 1, 2012

By M. J. Adam

The U.S. Bureau of Mines has investigated the partitioning of complex minerals to simpler phases using sulfidation reactions for selective extraction of mineral values. This report describes research in which thermal processing of the complex Ti-bearing mineral ilmenite (FeTi03) resulted in partitioning of the valuable Ti metal to the simpler compound rutile (TiO2). Samples of ilmenite were blended with elemental S for thermal treatment at various temperatures under controlled atmospheres in an effort to dissociate the Fe from the ilmenite complex. Product characterization revealed that the Fe was partitioned 'from the ilmenite, forming a rim of pyrrhotite/pyrite (FeS/FeS2) on a rut il e core. The products were agate milled and then subjected to cursory magnetic and flotation techniques in an attempt to physically separate the partitioned phases. Partitioning results and phase concentration data are reported relative to thermal treatment variables and physical separation techniques.

Jan 1, 1991

By George A. Calboreanu

In order to overcome drilling and tapping of high hardness wear resistent material in slurry pumps, most of time mild steel inserts are mounted in the mold and after pouring they become an integrated part of the casting. This process is limiting the size and design possibilities of slurry pumps and efforts were made to drill and tap the hard iron itself. The paper will present practical results obtained in drilling and tapping Cr-Mo wear resistent material with hardness in excess of 700 HBN. The life time of the slurry pump parts used in hazardous waste fuel transportation with high slurry velocity and 15% solid loading some of it being quartz, increased 2.5 to 6 times.

Jan 1, 1996

By Zhen Zhang, Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie, Hong-Yi Li

Extracting vanadium from vanadium containing hot metal by LD process has been proven an effective solution for the utilization of vanadium-titanium magnetite ore, but the systematic analyses of vanadium extraction rate and mechanism by basic slag are seldom reported. In this study, mathematical model of vanadium transfer from metal to slag was formulated and the rates of vanadium extraction of hot metal with basic slag were investigated. The results indicated that the apparent vanadium extraction rate constant, kp, were in the range of 1.33~9.07×10-4g/(cm3·s). And the rate constant was increased with the increase of final slag basicity, reaction temperature and stirring gas flow. The apparent of mass transfer parameter decreases significantly from 0.13 cm3/ s to 0 cm3/ s in 20min, and the data changed as negative due to the decrease of slag oxidation and recovery of vanadium from slag to metal.

Jan 1, 2015

By Wei Han, Zhenwei Liu, Jianhong Yang, Qingwei Qin, Tiejun Chen, Zili Huang

The preparation of industrial ammonium molybdate from molybdenum concentrate was conducted according to the process of roasting—leaching—purification—precipitation—crystallization. The optimum technological conditions were determined: the roasting temperature was 680 degrees C, the roasting time was 2.5 h; in the leaching process the alkali excess coefficient was 1.2, the reaction temperature was 80 degrees C, the liquid-solid ratio was 3:1, the leaching time was 3 h; the amount of (NH4)2S added into the solution was 1.1 times of the theoretical amount, the temperature was 80-85 degrees C, and the terminal pH was 8.5-9 in the purification process; the density of the solution was 1.4-1.6 g/mL, the pH was 1.5-2 in the precipitation process; temperature of dissolution was controlled at 80-90 degrees C. The recovery of the preparation of ammonium molybdate can reach 85.18%.

Mar 1, 2017

By Toshiyuki Kozuka

CdTe semi-conducting materials have been expected as solar cell materials because its theoretical energy conversion ratio is very high. The actual efficiency still low, however, many research works have been done in order to improve the efficiency. And crystal orientation is one of possibilities for that. In this work, a new method using intense magnetic field for a control of texture of CdTe crystals will be proposed, where the CdTe film was electro-deposited under an intense magnetic field. CdTe is less affected by magnetic field, because of its cubic structure, but Cd or Te has hexagonal structure, which is sensitive for magnetic field. In this paper, crystal orientation of Cd or Te film, which can be utilized as basic layer for CdTe deposition, will be developed.

Jan 1, 2006

By Harold R. Kokal

Lisakovsky is a 3-billion ton oolitic iron ore deposit in north-central Kazakhstan operated by Orken LLP, a subsidiary of Ispat Karmet and the LNM Group. The iron oxide minerals are goethite and limonite. The gangue occurs as discrete quartz grains and an unidentified form of colloidal silica-alumina. The concentrate produced contains about 49.5 percent iron (Fe) and 0.6-0.8 percent phosphorus (P) or 10-20 times the acceptable phosphorus level. The phosphorus is intimately associated with the iron oxide and colloidal gangue, no discrete phosphorus minerals are found, and beneficiation is not possible. Therefore, to reduce the phosphorus, a hydrometallurgical process that includes roasting followed by leaching in dilute sulfuric acid has been developed. Phosphorus extraction is 70-90 percent, with only a minor loss of iron. The process has been tested in the laboratory and in a pilot plant at 50-300 kg/h. Construction of a 900,000 t/y demonstration plant is underway.

Jan 1, 2003

By T. I. Arbuzova

The present work presents the original data concerning using a high pressure torsion method and a shock wave loading technique to produce compact oxide nanomaterials and investigations of the effect of severe plastic deformation on a microstructure, crystal lattice and stability of these compounds. This allowed us to compare two ways of deformation action that can be characterized as quasi-static and dynamic effect, correspondingly. Particular attention was paid to a stoichiometry and surface composition changes upon severe plastic deformations. A procedure for studying chemistry of the oxide nanomaterials by means of nuclear microanalysis and Rutherford back scattering has been worked through. For surface studies the X-ray photoelectron spectroscopy has been used. It was shown that both distortion methods permit to produce massive nano-scale oxide materials from the coarse-grained powder during a single technological cycle. Bulk nanocrystalline materials based on LaMnO3, TiOy and ZrO2:Y2O3 were obtained by the quasi-static deformation technique. Nanoscaled ceramics of CuO, Mn3O4 and LaMnO3 were produced by the dynamic deformations. The density of the nanoceramics comes to 99%. Size effects and specific imperfection of the nanoceramics obtained lead to a set of particularities of physical properties.

Jan 1, 2006

By Shinroku Matsuzaki

Data the measurement sensor installed with spatial distribution on the blast furnace were successively accumulated online from the process computer to the database system over a long period. This is a new system that accurately considers the relation with the installation position of each sensor, and picture computerization of the measurement data was developed. The overall operation state of a blast furnace, which skilled operators can see in their mind?s eye, was objectively visualized as pictorial information.

Jan 1, 2006

By Jing-she Li, Hai-yan Tang, Cheng-song Liu, Wei Liu

"In order to effectively utilize cheap and low quality iron ores, a hematite ore in a certain steel plant in Xinjiang was researched on to obtain ""iron increase and silicon reduction"" by ore dressing operation experiment and the performance indexes of the hematite ore were optimized. Based on the fundamental characteristics and high-temperature properties of the concentrate after ore dressing and other five kinds of iron ores which were co=only used in this steel plant, ore matching principles were proposed and a sintering ore blending optimization model was established. Finally, sinter pot test was carried out to verify the validity and practicability of the sintering ore blending optimization model which was aimed at giving consideration to the sintering indexes and the cost.IntroductionIn recent years, the price of imported iron ore with high quality is always at a high level, while iron ore self-sufficient rate in China is less than 50%. Enormous market demand and high dependence of domestic enterprises on imported iron ore makes the price of it hardly return to rational. In order to get rid of the situation of long-term meager profit and even deficit, more and more iron and steel enterprises in China transit their focus of reducing production cost to the utilization and development of relatively cheap but low-grade iron ore resources at home[l-4l_ However, besides the disadvantages of low iron grade, high content of impurities and complex embedded properties, the high-temperature properties of iron ore often go beyond the suitable ranges for producing sinter with high quality. Thus directly utilization of this kind of iron ore without ore dressing process would probably affect the metallurgical performance and indexes of sinter ore.Previous research and production practice have shown that traditional iron ore matching in sintering mainly focus on the reasonable collocation of properties of iron ores with low quality and high quality, but pay less attention to ore dressing process of low quality iron ores and matching them with high quality iron ores. Actually, compare with directly utilization, iron ores with low quality after ore dressing have higher suitability for matching with high quality ones which is beneficial to reduce the consumption of iron ores with high quality and control the production cost of sintering [5-s1."

Jan 1, 2014

In the new flowsheet for Inco Limited's S02, Abatement Project at the Copper Cliff, Ontario operations, a copper/nickel sulphide flotation concentrate will be flash smelted, then converted to Bessemer matte. As in current practice, this will be slow-cooled and separated into components by magnetic separation and flotation. The copper content will emerge as a chalcocite concentrate (impure Cu2S), containing some nickel. This copper sulphide will be converted to copper metal.

Jan 1, 1993