Search Documents

By W. G. Davenport

Chapter 10 showed that any given smelting task, e.g. production of 65% Cu matte, 1500 K, from CuFeS2, can be done with many different combinations of: blast%02 hydrocarbon fuel blast temperature. This chapter repeats the Chapter 10 calculations but reports the results in terms of the mass industrial oxygen mass hydrocarbon fuel blast preheat energy combinations that will produce 65% Cu matte, 1500 K, from CuFeS2 concentrate. It also determines the energy inputs equivalent to these combinations.

Jan 1, 2001

By B. Mishra

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite that is mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90 wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct. At this stage, the product could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. The mineralogical characteristics of the reduced product are not amenable to magnetic separation for iron recovery. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Special attention has been paid to lower the alkali content of the reduced material. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by an acid-leach process. This paper describes the successful efforts of iron and alumina recovery.

Jan 1, 2000

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By Peter R. Sanford

Cyanides are present as a dilute constituent of streams from a variety of metallurgical and mineral-processing operations. In addition, a cyanide concentration in excess of approximately 100ppb is toxic to aquatic life, and consequently these operations require a waste-treatment process to reduce the already dilute cyanide species by several orders of magnitude. Furthermore, the waste streams may have flowrates in excess of a million gallons per day. The paper reports on research conducted with a laboratory?scale electrochemical porous (graphite felt) electrode (anode) flow-reactor, which was conducted in conjunction with a computer-aided simulation of a mathematical model describing the intrinsic rate-phenomena associate with the electrode processes. The laboratory-scale cell, of rectilinear geometry, was found to be capable of reducing a feed-stream anolyte (KCN-KOH and supporting electrolyte of a single salt ? K2SO4) with a cyanide concentration of 10ppm, to less than 100ppb, at current efficiencies in the neighborhood of 50%. The computer simulation of the cell performance based on the mathematical model (and constraints imposed for tractability) was found to provide only for qualitative agreement.

Jan 1, 1998

By Zuhair A. Munir

"The use of self-propagating combustion reactions to synthesize metallic, ceramic, and composite materials is described. The limitation of this process because of the porous nature of its products is discussed. The formation of dense bodies through the simultaneous application of pressure is shown for a metal-matrix composite. The effect of an external electric field on the synthesis of ceramic and composites is described. The nature of the effect of the field on the mechanism of synthesis is analyzed theoretically and experimentally. The use of the self-propagating combustion to synthesize intermetallic thin films is presented for the Ni-Al and Ti-Al cases. The formation of functionally gradient materials (FGM) by centrifugally-assisted self-propagating high-temperature synthesis is described.IntroductionThe use of self-propagating combustion reactions for the synthesis of a large number of simple and complex materials has been described in numerous publications. These have been amply discussed in several review articles [1-4]. The many benefits of this method of materials synthesis are commonly examined in light of its most significant limitation: the porous nature of its products. The porosity in the products of self-propagating high-temperature synthesis (SHS) is an intrinsic characteristic of the process and its elimination has been the focus of numerous attempts. Various experimental methods have been used to accomplish this goal."

Jan 1, 1994

By R. Luo, R. V. Kumar

"The co-deposition of cobalt and nickel as a binary alloy has been studied by both cyclic voltammetry and long-period controlled-potential electrolysis. Cyclic voltammetry experiments showed that the cathodic current density for the mixed Co-Ni (Co-Ni=1:3) electrolyte is noticeably higher than that obtained on electrolyte containing single CO2+ or Ni2+ (II) salt of the same ionic strength. The onset potential observed for the mixed salts electrolyte was also less cathodic (negative) than that for the single metal salts, respectively. The effects of a number of operational and compositional parameters on the co-deposition of cobalt and nickel were studied. The parameters under investigation include cathode (deposition) potential, temperature, CI-/Sol ratio in the electrolyte, the amount of additives such as H3B03, and acidity of the electrolyte.Optimum operational conditions were established for the deposition of cobalt and nickel binary alloy. These results are discussed with respect to feasibility of reclaiming cobalt, nickel and chromium from mixed superalloy scraps by melt-refining (under nitrogen and/or ammonia), followed by electrorerining of cast anode for co-depositing Co/Ni and thermal decomposition of chromium nitride for recovering chromium metal."

Jan 1, 1997

By Mokka Rao, Arturo Valles, Jose Rodríguez

"This paper shows a mathematical model based on finite elements, applied to bottom poured shell ingots of C.V.G. Sidor Plant. The model was used as a strategy to determine the thermal effects that are produced when solidification conditions are modified without interfering with the production process. The modification consisted of placing a thermal insulator on top of mould.The results obtained by the model indicated that the solidification time increases with insulator on base of the mould. With these results a significant number of casts were run with and without insulator. Latter by means of a metallurgical analysis it was determinated that the ingots cast with insulator reduce the level of non-metallic inclusions and the presence of internal blistering in seamless pipes.IntroductionThe process of fabrication of seamless pipes in SIDOR involves various steps of processing, such as heating the ingots, fabrication of the prelaminated, fabrication of the bored pipe, lamination of the pipe by passing through the pellegrine mill, heating the pipe in a walking bean furnace and final calibration through a calibrator mill. The material utilized for producing these pipes is provided entirely from a electrical arc furnace and casted ingots, especifically, from the superintendence of bottom pouring.The process of bottom pouring consists of positioning twelve moulds of diameters 415, 480 or 505 mm over a plate of grey cast iron in which exists a system of communicating vessels. The ingots are distributed around a central duct from which the steel flows down and filling gradually, each one of the moulds (Fig. 1)."

Jan 1, 1997

By Ryokichi Shimpo, Akio Fuwa

"In order to elucidate the present status of process-control technology, survey study has been made on the present process control schemes of representative copper smelting and converting processes in Japan. Conceptual control flow diagrams have been deduced and shown on respective functional reactors, i.e. drying, smelting, converting and fire-refining units, where the objective OUTPUT items are correlated to the INPUT variables through respective CAUSE-AND-EFFECT RELATIONSHIPSFuture view has been also discussed on several feasible and desirable improvement and refinement ~n measurements and control system for better copper smelting and converting operations.INTRODUCTIONIn other to seek for the better and efficient operation in copper smelting and converting process, survey study has been first conducted on the present process-control schemes of respective functional unit processes, i.e. drying, smelting, converting and refining unit processes, of representative copper production processes in Japan. Conceptual process flow chart of control scheme has been then deduced where output items are correlated to input items through the respective cause-and-effect relationships.After this survey study, future view has been discussed on the feasible and desirable improvement and refinement in the measurement and control system in these processes. Emphasis has been placed on the better and precise measurements of temperature, oxygen partial pressures in respective furnaces and end-point in converting and refining unit operations."

Jan 1, 1989

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

By Monteirom Sergio N., Romulo L. Loiola, Giulio R. Altoe, Noan Simonassi, Frederico M. Margem

"The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. Buriti fiber extracted from buriti palm tree (Mauritia flexuosa), presents some significant characteristic, but until now only few studies on buriti fiber were performed. This work aims to make the analysis of the tensile strength of epoxy composites reinforced with buriti fibers. This analysis was performed in fibers with diameters between 0.1 and 0.4 mm. Those fibers were incorporated into the epoxy matrix with volume fraction from 0 to 30%. The fiber diameters were measured by a profile projector. After fracture the specimens were analyzed by a SEM (scanning electron microscope).IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times of our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles, sports goods and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber(1). In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites(2-3). Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to CO2 emissions responsible for global warming. In addition to environmental benefits(l,10) the lignocellulosic fibers present economical advantages, such as worldwide abundance and comparatively low costs as well as some technical properties associated with flexibility and toughness( 4), which contribute to the performance of automobile components fabricated with natural fibers composites(l 1-13)."

Jan 1, 2013

By Guo-hua Bai, Hong-jing Yuan, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

"The effect of different additives on the bio-oxidation of arsenic-bearing gold ores has been carried out to solve the problems such as long period of leaching, low oxidation rate. The oxidants strengthen the cathodic reaction and thus improve the leaching rate by the increase of electron transfer. Meanwhile, silver catalysis is also effective for the decomposition of arsenicbearing gold ores due to the strengthening of anode reaction. Co-intensification by oxidants and Ag (I) is more efficient to the bio-leaching and the conversion of As (III) because the anode and cathodic reaction of biological oxidation of sulphide ores were both strengthened. The leaching rate reached to 63.94% after bio-leaching 13days by co-intensification of Ag (I) and Fe(III).IntroductionWith the worsening global ecological problems and the gradual exhaustion of available gold resources, metallurgical technology of refractory gold ore has received more and more attention and become possible due to its good advantage of the economic effects and negative effects to the environment. Refractory gold ore, the direct cyanide leaching rate of that is defined as less than 70%, has become an important raw material in gold extraction industry, in which sulfide bearing gold ore represents a large proportion, pyrite and arsenopyrite (FeAsS) is a common gold-bearing mineral. Since the gold is often encapsulated in the crystal lattice of these minerals, destruction or alteration of the ore to liberate the submicron and/or structurally bond gold is necessary[l]. Even if the ultrafine grinding approach also is generally not sufficient for these refractory ores and additional techniques like roasting, pressure oxidation and bacterial oxidation are used to liberate the gold [2]. In the three pretreatment processes, bacterial oxidation is characterized by its new ideas, low cost, no pollution, simple equipment and operation, high leaching index and become the most promising process which has received much attention over time [3-5]. But its further application is limited by some of its own shortcomings, such as long pretreatment time and the toxic effects of arsenic to bacteria on bio-leaching limit."

Jan 1, 2013

By M. Fafard, R. Ahmed, O. Dion-Martin

"The optimization of aluminum sheet and tube forming needs the use of large strain finite elements software. The precision of the predicted results from those simulations depends mainly on the quality of constitutive law of the material used. In order to improve quality of these simulations, Barlat has suggested a new yield function named YLD2000-2d. This criterion describes the anisotropic behavior of the rolled aluminum plates. This work consists of characterizing the AA5754 alloy and estimating the material parameters needed for the YLD2000-2d criterion in LS-DYNA. In order to get these parameters, various mechanical testing were performed such as bulge and tensile tests. Moreover, the bulge test was also used to obtain an estimation of work hardening curve in large strain condition, up to 50%. The objective of this paper is to share the experimental results of the characterization of AA5754 aluminum alloy.IntroductionResearchers from National Research Council Canada's Aluminium Technology Center (NRCATC) and Aluminium Research Centre - REGAL, are working on aluminium tube hydroforming processes of AA-5754-0 alloy, used in automotive industries. Hydroforming process presents several difficulties such as wall thinning and section changes. In order to control them, some parameters can be set during the process like pressure rate and end feed level [1]. Given the complexity of the parts and the variability of the control parameters, the use of finite element method (FEA), like LS-DYNA, based on large strain theory is thus necessary. The accuracy of predicted results depends mainly on the quality of the constitutive law used to model the behavior of material. FEA results seem to be valid with the von Mises yield criterion used in some cases. But, given the anisotropic properties of the AA-5754 alloy, a more appropriate criterion could be used. The *MAT_ BARLAT YLD2000 shell material criterion, developed by Barlat [2], who's taking into account the anisotropic behaviour, was chosen due to its large flexibility and its good adaptation to particular elastoplastic behavior of aluminum. However, the use of this criterion needs to determine some material parameters by experimental way."

Jan 1, 2013

By Hanlu Xie, Liang Yu, Ping Wang, Yuanchi Dong

"The leaching process is the first step when recycling BF slag as raw material for some other products. While studying the kinetics of the BF slag leaching process, a fractal phenomenon was found, which indicated some interesting mechanism in the process. The result suggested a new understanding of the leaching process in detail which useful for the industrial applicationIntroductionTypical composition (wt. %) of blast furnace slag varied in a pretty wide range: SiO2 30–40, Al2O3 10–20, CaO 30–40, MgO 5–10.The ground granulated slag is commonly used as base of roadway (mixed with natural inert for paving, soil stabilization, etc.) or one of the resources of Portland cements because of its good hydraulic activity [1]. To recycle the slag economically, the selective recovery of some components of the slag may be considered. As main components exist in the slag, silica [2, 3 and 4] and alumina [4] recovery was first considered.While recovering of silica from the slag, silica gels are recovered selectively from the leaching solution deriving from the treatment of the slag with waste sulfuric acid. After separation of the exhausted solid of leaching, the silica gel is precipitated from the solution at pH 3.2. Although the silica gels obtained by this procedure contain many impurities and need some more work afterward, it is the first and important step for the process.In the prior work [5], silica extraction using blast furnace slag had been investigated, focused on the pH value of selectively silica extraction. In the present work, kinetics of the leaching process was focused. It is important to design an economical process.ExperimentalThe composition of the slag and the calcined gels has been determined by a LINK860 (Oxford Instruments, Oak Ridge, TN) energy dispersive spectrometer (EDS) in conjunction with a CAMBRIDGE S250-M2 (Cambridge Instrument Ltd., Cambridge, U.K.) scanning electron microscope(SEM). The leaching of slag and the precipitation of silica gels have been conducted at atmospheric pressure in a stirred reactor placed at temperature controlled by a heated water bath."

Jan 1, 2008

By Cheng Gong-jin, Chu Man-sheng, Liu Zheng-gen, Zhang Yong, Liu Jian-xing, Xue Xiang-xin

"High chromium vanadium-titanium magnetite is one kind of Fe-V-Ti-Cr composite ore resources, which owes high utilization value. Owing to lacking systematic study on the sintering of this ore home and abroad, effects of carbon addition and basicity on sintering process and sinter metallurgical properties, such as sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation were investigated systematically under laboratory conditions in the paper. The results shows that, when high chromium vanadium-titanium magnetite proportion is kept unchanged as 13% in sintering feeds, sintering process index and metallurgical properties are the optimum under carbon addition 5.0% and basicity 2.70, which meets the requirements of blast furnace burdens. This research provides technical parameters for practical sintering production of high chromium vanadium-titanium magnetite.IntroductionHigh chromium vanadium-titanium magnetite (hereinafter abbreviated as hi§h-Cr V-Ti magnetite), in which Fe is closely symbiotic with Ti and isomorphous with V and Cr1'- l, is one kind of typical vanadium-titanium magnetite resources with high comprehensive utilization value but the difficulties are extremely high due to complex chemical composition and mineral structure. At present, the feasible and mainstream utilization process of high-Cr V-Ti magnetite should be the route of agglomeration-blast furnace smelting. Thus, sintering production is the foundation for high-Cr V-Ti magnetite utilization. However, till now there are few research documentations on high-Cr V-Ti magnetite sintering home and abroad. Under the above background, this study focused on detailed researches of high-Cr V-Ti magnetite sintering. Sintering process uses the powders or fine iron ores to produce artificial rich ore with good metallurgical properties 4l Solid fuel provides 90% heat requirement during sintering15J. The appropriate amount of fuel and flux should be added during sintering in order to provide necessary heat and maintain the desired basicity16l. That is to say, carbon addition and basicity are two key factors affecting metallurgical properties of sintering products17J. Therefore, the effects of carbon addition and basicity on sintering process and metallurgical properties, including sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation, are systemically investigated under laboratory conditions in the study, on purpose to achieve the optimization of sintering process for high-Cr V-Ti magnetite."

Jan 1, 2013

By Linli Wu, Guangchun Yao

"The influence of deformation on the properties of short-carbon-fiber reinforced 2024 alloy matrix composites was investigated in this study. It was found that the distribution of carbon fibers changed from the random state before deformation to the ordered state that carbon fibers arranged along the direction of rolling and extruding after deformation. Under the temperature range in control, the increase of rolling and extruding temperature would benefit to improve strength and elongation of composites, but was not conductive to improve the hardness of composites. With the increment of total deformation, all the strength and the hardness of composites became greater, nevertheless the elongation decreased. After being rolled and extruded, the strength and the hardness of composites were all bigger than those of composites before being rolled and extruded; moreover, the strength of extruded 2024 alloy matrix composites was higher than that of rolled 2024 alloy matrix composites under the same heat treatment conditions.IntroductionCarbon fibers have been reckoned as very important reinforcements due to the high specific strength, specific modulus, high thermal and electric conductivity, low expansion coefficient and good self-lubricant properties [1-4]. Light metal composites reinforced with carbon fibers, such as carbon fibers in an aluminum matrix, are widely used and studied. Some studies have concentrated on the interfacial characteristic of CF/Al composites in order to search for the way of improving the bonding between carbon fibers and the matrix alloy [5-8], and on the influence of the carbon fiber percent composition in the composites [9-11]. Some researchers began to take interest in the deforming characteristic and failure behavior of carbon fiber reinforced metal matrix composites [12-16]. However, the same with other metal materials, most of CF/AI composites were prepared by some single processes, such as powder metallurgy, extrusion casting and vacuum press infiltration, which caused that the composites products could not be manufactured directly. In order to cover the shortage of the mentioned above processes and get composites products with perfect mechanical properties and dimensional accuracy, the composites should be reworked by rolling, extruding or forging process. Compared with research about manufacturing process, the correlative investigation on the reworking of CF/Al composites was much less evidently, which restricted the application and the further development of CF/Al composites."

Jan 1, 2012

By Frank Field, Elsa Olivetti, Randolph Kirchain, Elisa Alonso, Gabrielle Gaustad

"The primary technological challenge to increased use of secondary raw materials is the presence of undesirable elemental species in scrap streams. Recent literature indicates that this may become exacerbated by accumulation of impurities over time. Devising strategies to mitigate this problem depends upon understanding the mechanisms of accumulation. This paper takes a first step at characterizing the extent of this issue by presenting a simple analytical model of recycling rate for materials experiencing exponential growth. Low potential recycling rates limit accumulation due to dilution. Empirical analysis of several major materials indicates that, even for current recovery rates, theoretical recycling rates can reach above 60%, making accumulation issues a possibility.IntroductionIt is well known that recycling of secondary materials can provide significant environmental and economic benefits. Energy savings, in particular, can be quite large when substituting secondary materials for primary. Nevertheless, over the past decade, the recycling rates within the U.S. of many materials appear to not be increasing as rapidly as one would predict or even at all (Figure 1). While many barriers exist to increasing materials recycling, one that is cited consistently by the literature and producers[1-3] is compositional limitations; that is the mismatch between the characteristics of secondary materials and those desired for the finished goods into which they would be transformed..One particular aspect of compositional limitations that is receiving increasing attention is the potential for progressive deterioration of the quality of secondary raw materials streams. For some materials, for example paper or polymers, this phenomenon is inherent and relatively rapid[4, 5]. As such, it is well documented and plays a significant role in recycling decision-making even for prompt or in-house material recycling. Conceptually, this issue can manifest in other secondary materials as well, albeit through a different mechanism.As materials are mixed, used, and reprocessed during recycling, they come into contact with and often pick up other elements. The presence of these, so-called, tramp elements alters the original known composition, possibly requiring additional measurement and processing and may even preclude economic, productive reuse; ultimately, this unintentional pick up is unwanted. A growing number of studies and literature would suggest that accumulation of unwanted elements is an emerging problem, in most recycled material streams. Table I provides a brief literature review of various recycled material streams and the accumulated elements noted as problematic by various authors"

Jan 1, 2008

By R. J. St. Eloi

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year .. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to .generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to 'improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates;

Jan 1, 1992

By Okechukwu Anopuo, Gerhard Tober, Petra Maier

"In this study, an investigation on the microstructure of hot rolled steel S355J2+N was conducted to optimize process parameters of complex forming, which combines rolling and bending. The best sets of parameters are worked out based on homogeneous mechanical properties and microstructure within the varied deformation degree with maximum at <p = 1.14 on a 25 mm thick plates. Mechanical properties, especially of heavy plates, are strongly influenced by the local deformation degree, strain rate and temperature. Detailed microstructural analyses showed that the ferrite-pearlite band structure changes near the surface, while maintaining homogeneous microstructure within the deformed work piece. Surface decarburization was also observed and this leads to decrease in hardness. To minimize iron oxide formation which could lead to side cracking, reduction in exposure time to temperature was suggested. On the other hand, temperature reduction below a critical value would risk the accurate forming process.IntroductionThis work presents the preliminary results of research to develop a new complex deformation process of thick steel plates. Complexity is given because the forming process combines rolling to reduce thickness and profiling by bending. The work piece will experience a thickness reduction from 25mm to 8 mm and is double curved. To explain and understand forming of thick plates basics of sheet forming as well as massive forming need to be used. At the moment there is no forming process established to produce double curved plates including reducing thickness in one process step. Technologies nowadays consist of two process steps: flat rolling and pressing in shape. Due to good weldability and formability the final product will be made of steel S355J2+N. This low-carbon steel is well understood and has a low strengthening exponent, which is expected to keep the forming forces down. Reduction of thickness from 25 mm to 8 mm gives furthermore a high deformation degree. Thus, hot forming has to be applied. The determination of process parameters is the main aim of overall research project; temperatures above lOOO°C are expected. Flow curves in literature are given at various temperatures and strain rates [1]. However, experiments with data close to the industrial application are rarely found, especially at low strain rates and high deformation degrees. Pre-test were done by flat rolling, being aware that the influence of bending is eliminated. The microstructure evolution were characterised in relationship to material formability with special attention to grain size change and recrystallization. Representative samples should be selected from specific locations in the deformation zone according to the knowledge about the metal forming process [2]. Due to no further alloying elements in S355, no precipitation hardening is expected to take place during hot forming, which keeps the mechanisms simple and the concentration on the feasibility of the complex forming process is given."

Jan 1, 2012

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008

By J. C. Yannopoulos

The quest for a continuous copper smelting and converting process, which has been going on for a long time, has not as yet reached its objective. The most recent efforts for the development of a continuous copper?making process started about two decades ago. Among the contending proposed processes, four have been piloted and three of them are currently in operation: the WORCRA process., the NORANDA process, the MITSUBISHI process, the OUTOKUMPU process. The WORCRA process, after some long pilot plant tests, failed to develop as an industrial process: The NORANDA process, as currently operating, is a smelting process and not a continuous copper?making reactor as initially conceived. The MITSUBISHI, although the only continuous process, has not been widely accepted. The OUTOKUMPU process can be applied only to a low iron concentrate feed and co?produces blister and high in copper slag. The thermodynamics of these "continuous" systems and the practical problems of their industrial application are reviewed and discussed. The achievement of efficient and inexpensive environmental control should&apos; be the primary objective of any new process development. A review of the environmental problems of the copper industry indicates that the quest for a continuous smelting and converting furnace should be intensified.

Jan 1, 1983