Search Documents

By V. A. Shumsky, I. P. Polyakov, N. M. Ospanov, M. A. Lyamina, N. N. Ushakov

Studies on the kinetics of the competitive processes of PbS volatilization and PbS oxidation, as applied to the heat and mass transfer conditions in the flame of the Kivcet furnace, revealed that the rate-determining factor is the supply of heat. Therefore, low yields of fume in the autogenous flash smelting of lead sulphide feeds are noted despite the high volatility of PbS at 1,300-1,400°C. Dust formation in the autogenous flash smelting of Kivcet-smelters does not exceed 5-7%, of which fumes amount to ~ 80%. Using extra fuel during autogenous smelting involves the mismatch of the sulphide oxidation rate and the release of heat in the flame, and increases the fume yield. This is a major cause of the high dust formation in pilot plant trials. The analysis of dust formation in the Kivcet smelting of oxidized lead feeds in an industrialscale smelter shows an overall increase of dust formation (up to 10% of the feed), with fumes constituting ~ 80% of the dust. A pronounced increase of the zinc component of the fumes is also noted. Lead

Jan 1, 2000

By Peter G. Smith

Tri-calcium aluminate (TCA) is a dominant alkaline component of the red mud residue from the Bayer process. A method being considered for industrial implementation partially neutralizes the residue by contacting it with gaseous CO2. This paper outlines the chemistry of CO2neutralisation of TCA under conditions relevant to the treatment of Bayer residue. CO2 neutralisation of the liquor is fast. It results in the formation of amorphous aluminium hydroxide and dawsonite that agglomerate together. Neutralisation of solid TCA is slower and leads to the formation of calcite, dawsonite and amorphous aluminium hydroxide. The dissolution of TCA in partially neutralised slurries causes pH reversion. However the carbonated solutions contain a store of bicarbonate that can supply aqueous carbon dioxide to complete the transformation. The pH at which the carbonation is carried out will affect the degree of TCA transformation during the carbonation process. In particular, if the pH of the carbonation is too low (near 7.0), calcite precipitation is inhibited and the degree of transformation is low. Controlling the carbonation pH helps to optimise the neutralisation process.

Jan 1, 2003

By Li Kaihua, Li Liang, Miao Qingdong, Wang Cong

The current process of production of titanium sponge involves the use of TiCl4 as a feed material and a huge amount of heat is generated during the magnesiothermic reduction process. For this reason, it is possible to agglomerate into a titanium lump with the partial high temperature. And, it is difficult to obtain soft titanium sponge with low content of impurities. In order to solve the current problems in the titanium sponge production process, process optimization experiments study of TiCl4 feeding speed, vacuum distillation temperature, system pressure and time control had been conducted for obtain high quality titanium sponge. Experimental results show that lower feeding speed can improve the output capacity of titanium sponge and softer products can be obtained. The product grade rate of titanium sponge improved significantly.

Jan 1, 2015

By S. E. Khalafalla

A method for preparing ferrochromium alloys containing less than 2 pct carbon has been devised in a single vacuum furnace reactor. This method can conserve chromium and should reduce the capital and energy requirements relative to chromite electrothermal reduction. Reduced products containing less than 2 and as low as 0.01 wt pct carbon were obtained by reacting pellets of chromite and carbonaceous reductant mixtures at pressures of 0.1 to 1 ton and temperatures of 1,230° to 1,320° C. The extent of reduction increased with increased temperature and decreased pressure; however, operating conditions were limited due to the onset of significant chromium vaporization at higher temperatures and lower pressures. Foundry coke, anthracite, and carbon black were found to be superior to graphite as reductants. The reduction of chromite to metallics was found to proceed via the carbide intermediates Fe3C or Cr3C2. Lime accelerates the. rate of solid state reduction of chromite and can shorten the furnacin1r time at 1,3000 C under vacuum from 13 hours to less than three hours. Additional lime and silica are added to the hot reduced chromite after releasing the vacuum and raising the furnace. temperature to 1, 700° C. Soaking the charge for about 20 minutes gave a button of low carbon ferrochromium alloy beneath a well-defined slag layer.

Jan 1, 1985

By Kimio Itagaki, Makoto Ohtsuka, Kouki Chiba, Minoru Matsumoto

"The properties of Ni-Mn-Ga films such as chemical composition, crystal structure, microstructure and transformation temperature were investigated with respect to sputtering conditions in the present study. The Ni-Mn-Ga films were deposited on a polyvinyl alcohol substrate with a radio-frequency magnetron sputtering apparatus using the NisoMn2sGa2s and Nis2Mn:«1Ga24 targets. After separating from the substrates, the films were annealed at the temperature between 873 and 1273 K for 3.6 ks. The chemical composition of the films depended on the radiofrequency generating power, however, there was no dependence on the heat treatment temperature. Each deposited film had a columnar grain structure. After heat treatment, the width of columnar grains widened and then became indistinct with increasing heat treatment temperature. The Heusler type cubic crystal structure of the fi4n with heat treatment at 1073 K changed to the tetragonal one through the martensitic structural transformation during cooling. The martensitic structural transformation temperature increased with increasing nickel content of films, while the Curie temperature decreased. The film obtained at 200 W using the Nis2Mn24Ga24 target after heat treatment at 1073 K showed one-way shape memory effect through the reverse martensitic structural transformation during heating.IntroductionThe ternary intermetallic compound NiiMnGa has a Heusler-type crystal structure and is an intelligent material, which has a shape memory effect and a ferromagnetic property. The martensitic structural transformation occurs within the ferromagnetic temperature region. The cubic crystal structure of L21 at high temperature changes to a tetragonal one through the martehsitic structural transformation during cooling. The films of this compound can be applied for an actuator of micro-machines."

Jan 1, 2000

By KNona Liddell

Many metal recovery processes Involve heterogeneous reactions In porous media accompanied by fluid flow and mass transfer. Modeling such systems Is difficult because of the number of rate processes Involved and is complicated even further by effects due to the structure of the porous medium. Data on even bulk properties of the medium are often severely limited or unavailable. For many such systems, a cell model may provide, an attractive alternative to models based on transport ,mechanisms in a differential volume. A cell model requires less input data and is computationally efficient. Identical residence time distributions can be obtained with models of both types, and both allow conversion and concentration profiles and histories to be calculated. The formulation and properties of cell models for metals recovery are described in detail.

Jan 1, 1996

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

By ZHANG Ting

In view of the high consumption and contamination of traditional vanadium extraction technology, a new process of leaching the converter vanadium slag without roasting with titanium dioxide waste was proposed. Extraction mechanism of P204 in the leaching solution had been researched and single factor experiments show that after a prereduction of Fe, and under conditions: ambient temperature，leaching solution original pH=2.5, phase ratio (A/O)=1:3, shaking time 8min, the extraction rate of V is more than 98.62% meanwhile the separation rate between V and Fe is up to 135.3 in the 20%P204-10%TBP-Sulfonated kerosene extraction system.

Jan 1, 2015

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment .step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1M sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250 °C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 1995

By R. E. Sundell, S. M. Correa

"A mathematical model is developed for the fluid flow in tungsten-inert gas weld pools. The fluid is taken to be incompressible, viscous, electrically conducting, and confined within a pool of specified shape. The flow is driven by surface-tension gradient (thermocapillary), electromagnetic, and buoyancy forces generally in this order of importance. Analysis indicates that the electromagnetic field may be calculated a priori and so decoupled from the nonlinear fluid mechanics and heat-transfer problem. The resulting set of equations is solved numerically by a line relaxation process. Computational errors caused by truncation in finite-difference schemes and by inadequate grid distributions are considered. The model is used to study several cases of differing heat and current input to the pool with and without surfactant-induced thermocapillary forces. The principal conclusions are that the thermocapillary flow, when present, is dominant with surface velocities on the order of 1 m/s. The heat transfer, as deduced from isotherms within the pool, is crucially dependent on the flow. Also, flow velocities and weld-pool surface temperatures were measuredand agree well with the model.2. IntroductionThe requirements of improved control and of automation in the TIG (tungsten-inert gas) welding process have led to the development of mathematical models for the heat transfer to the workpiece. It is now widely recognized that the fluid flow in weld pools sufficiently distorts the conduction heat transfer pattern to warrant inclusion in a process model. The experiments of Woods and Milner (1), among others, demonstrated that TIG weld pools could be driven by the electromagnetic J x B body forces present, J being the current distribution and B the induced magnetic field. Atthey (2) calculated that in typical pools the buoyancy force was about an order of magnitude less important - despite the large temperature gradients present - and neglected it in a computational study of the magnetohydrodynamic (MHD) flow. This work also reviewed many earlier studies of MHD flow caused by a source of current at a fluid surface, including analytical studies by Shercliffe (3), Sozou (4), and Sozou and Pickering (5), and a numerical study by Andrews and Craine (6). These works establish the importance of the electromagnetic force in the weld-pool flow."

Jan 1, 1986

A novel pressure leaching process for platinum group metal (PGM) feedstocks is described. The process is particularly well suited for treatment of ores or concentrates that are too low grade for economic processing by the conventional smelting/leaching process. Operating conditions have been identified under which gold, the PGM's and the base metals dissolve simultaneously in a pressure leaching autoclave. The product of this leaching process can then be treated by one of several flowsheets, of which the preferred will likely involve solid/liquid separation, followed by precipitation (or adsorption on activated carbon) of gold and the PGM's, followed by copper solvent extraction/electrowinning. Depending on the concentrations of nickel and cobalt, the copper raffinate would either be partially recycled to the autoclave to allow NilCo concentrations to build up, or it would proceed directly to a Ni/Co refinery. This paper deals with the pressure leaching process and the recovery of gold and the PGM's from the pressure leach product.

Jan 1, 2000

By D. J. Webb, D. G. Reynolds, D. W. Ashman, D. W. Goosen

Cominco Limited operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Central to the successful operation of this complex is the treatment of zinc leach residues through the lead smelter. In 1997, Cominco started up a new lead smelter using KTVCET flash smelting, a state-of-the-art conventional slag fuming furnace, and a new drossing plant. The smelter has fully met the requirements for environmental performance, reduced energy consumption, and lowered labour costs. This paper provides a description of the new smelter and discusses the problems encountered during the start-up, as well as the solutions to those problems. Recent operating results are presented. Lead-Zinc

Jan 1, 2000

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Yingli Liu, Yuanyuan Zhang, Hailong Huo

Coal burnout strongly depends on the residence time and dispersion of coal particles in the raceway region of a blast furnace. The residence time and dispersion of coal particles are directly related to the lance arrangement. In this work, a three dimensional model was developed to simulate the lance-blowpipe-tuyère-raceway region of a blast furnace. Double lance and eccentric configurations were considered. For the double lance, the double-lance and eccentric double-lance were considered. For the eccentric double lance, the effect of intersection angle of the two lances was investigated.

Mar 1, 2017

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By James T. Skoch

With the ongoing pressure on the secondary aluminum business to limit the amount of waste generated from processing aluminum dross, it becomes very advantageous to preprocess the dross to reduce waste. The advantage of preprocessing is that it significantly reduces the oxides and salt cake generated when melted. Various products can be produced from the oxides for the steel industry. The following paper will demonstrate that removal of oxide fines before melting will result in large volumes of material not being landfilled. We will show that the end result of this technology is to significantly reduce the amount of salt cake sent to a landfill while maximizing the recyclability of the aluminum dross.

Jan 1, 1995

By Thomas Niehoff, Dave Stoffel

"Energy in the form of natural gas, oil and electricity is expensive and will continue to be a rare resource in the future. Recycling of metals, instead of primary production, is a logical and crucial step towards energy conservation. Energy consumption can be impacted by using advanced combustion systems for metals recycling. Air-fuel combustion has been the conventional method to melt and recycle metals. Global competitive pressures, “greenhouse” gas emissions, and high energy prices force melt shop operations to optimize energy usage and reduce overall operating costs. Oxy-fuel combustion and process technology can be applied to metal recycling operations to meet these objectives. Linde has converted several hundred furnaces from air-fuel to oxy-fuel technology and has extensive experience in optimizing the use of oxygen in furnaces. Additionally, Linde has the process knowledge necessary to avoid costly start-up issues that can accompany the transition to oxy-fuel technology. This paper will describe the benefits and potential issues for conversion to oxy-fuel.IntroductionThe furnace combustion system is the heart of a fossil fuel fired melting process and must be properly matched to the furnace to work as one cohesive unit. Furnaces vary widely in size, shape and features. Rotary furnaces are barrel-shaped and can be designed for tilting or nontilting operation. In a rotary furnace, the products of combustion create a single or double pass through the furnace prior to exiting. Reverberatory furnaces are box-shaped and can also be designed for tilting or non-tilting operation. Reverberatory furnaces are constructed of single or multiple chambers, with or without metal bath movement, and designed for continuous or batch processing. Different furnaces are used for different feedstock materials and products.Furnace combustion systems also vary in many ways. Combustion systems can be of air-fuel or oxy-fuel based technologies, or a combination of the two, resulting in an air-oxy-fuel system. Each of these types of systems has different combustion characteristics which can produce very different results. Here we will describe specific differences in melting processes and their associated energy requirements."

Jan 1, 2009

By George P. Demopoulos

n this study we have sought to highlight the critical linkage between individual reaction kinetic parameters (usually determined in small bench scale experiments) and large continuous reactor performance by focusing on the industrially significant zinc pressure leach process. To this end a comprehensive mathematical model previously developed for the description of this process was employed. In this paper we have examined in particular how small variations in key kinetic parameters impact on the autoclave&apos;s performance, i.e. attainment of autogenous steady-state temperature, zinc conversion and solution chemistry. The reaction parameters studied were: (i) stoichiometry of the marmatite leaching reaction; (ii) the activation energy of the same reaction, E,; (iii) the rate constant of the ferrous to ferric oxidation reaction, k,; and (iv) the apparent equilibrium constant for ferric precipitation, K,. This parameter sensitivity analysis was done under no oxygen mass transfer control limitations. Model predictions were found to be more sensitive to the kinetic parameters under certain conditions than others. The most dramatic finding was the one related to the small amount of sulfate produced during marmatite leaching. In connection to this it was found that the small percentage (< 5 %) of sulfate produced enhances the autothermal operational stability of the autoclave. The need for accurate kinetic parameter determination under conditions similar to those encountered in industrial zinc pressure leaching was demonstrated.

Jan 1, 1999

By Zhenfeng Zhou, Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

The oxygen blast furnace is a new technology for ironmaking, where the oxygen and CO2-stripped blast furnace top gas are blown into the blast furnace replacing the conventional hot air. The oxygen blast furnace could reduce the consumption of coke and emission of carbon dioxide. In this chapter, a three-dimensional numerical model was developed to simulate the lance-blowpipetuyere-raceway region of a blast furnace, and the flow and combustion behaviors of coal particles were investigated based on an oxygen blast furnace. Compared with the traditional blast furnace, the combustion characteristics in the raceway of the oxygen blast furnace were different. In addition to the combustion of coal and coke, the combustion of large amounts of reducing gas was included. The coal combustion of different oxygen content (70, 80, 90, 100%) were investigated. The simulation results indicated that the coal burnout was only 21.64% at an oxygen content of 70%, a decrease of 51.52%, compared with a traditional blast furnace. The coal burnout was increased with the increase of oxygen content. When the oxygen content is 100%, the coal burnout was 90.38%, an increase of 17.22%.

Mar 1, 2017

By T. Manlyama

The Tamano Smelter of Hibi Kyodo Smelting CO., Ltd. went into operation in 1972. The Flash Smelting Furnace that was originally adapted was equipped with electrodes that were attached to the settler substitute of the slag cleaning furnace. Later the development of our own original coke combustion technology was promoted and a new Tamano Type Flash Smelting Furnace (T-FSF), without electrodes, was put into operation in 1988, T he technology of coke combustion and combustion the burner have continued to improve. As a result the copper losses in the Wag have been reduced as well as a stable operation has been achieved, Furthermore; this has been accomplished while increasing the concentration feed and the matte grade. The current objective is to continue to strive for high matte grade operation and to raise production efficiency while paying attention to the important subject of copper losses in the slag. In this report, the data related to the copper loss in the slag reduction are presented along with the influence of the thickness, settling time and coke. The recent operation conditions of the T-FSF are also presented.

Jan 1, 2003