Search Documents

By A. O. Apata, F. V. Adams

The use of rice husk ash as aggregate for foundry sand mould production has been studied. 5 –25wt% rice husk ash was added to the sand mixture. The chemical, physical and mechanical properties measured include: chemical analysis of the rice husk ash, particle size, density, permeability, compatibility mouldability, moisture content, green compression and shear strength, dry compression and shear strength. The result revealed that, addition of rice husk ash to River Niger Silica sand, increased the mouldability, compatibility, grain fineness number, both green and dry strength, slightly decreased the density, permeability and moisture content. The result shows that better properties is achievable by the addition of rice husk ash to River Niger silica sand and can be used to enhance the mould properties of foundry sand.

Mar 1, 2017

By Muammer Kaya, Sait Kursunoglu

"The aim of this study was to investigate the effectiveness of ascorbic (C6H8O6) / oxalic (C2H2O4) acid as a reductant for the simultaneous recovery of zinc and manganese from a spent and mixed zinc-carbon and alkaline battery powder in sulphuric acid leaching. The effects of sulfuric acid concentration, ascorbic/oxalic acid dosages, reaction temperature and leaching time on the zinc and manganese dissolutions were investigated according to 2k full factorial experimental design; then, a simple optimization study was carried out for the best reductant. The optimum reductive acid leaching conditions were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M sulfuric acid concentration, 13 g/L ascorbic acid dosage, 1/20 g/mL solid/liquid ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. When our results were compared with the previous results, our findings were better than previous studies.In addition, the manganese dissolution kinetics was undertaken, and the activation energy was found to be 7.04 kJ/mol. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leaching solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover zinc and manganese."

Jan 1, 2012

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can’t meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

Jan 1, 2015

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, a three dimensional finite-volume model has been established, and the fluid flow and heat transfer in the super-wide slab mold (cross section 3250mm×150mm) of Nanjing Iron and Steel Company has been simulated. The basic feature of flow and temperature field in a super-wide mold has been analyzed, and the effects of mold width, the submergence depth of SEN, outlet angle of SEN, casting speed, superheat and cooling rate on the flow and temperature field have been investigated. The results by comparing several simulated calculations for 3250mm×150mm slab show that a more proper fluid flow and temperature field in the super-wide mold can be obtained with 15°outlet angle, 120~150mm submergence depth of SEN and 1.2~1.4m/min casting speed. The results through numerical simulation provide a theoretical basis for optimizing the configuration design of SEN and choosing reasonable processing parameters for the continuous casting mold of super-wide slab.

Jan 1, 2009

By Ying Mao, Zhancheng Guo, Long Ma, Huiqing Tang

"A new 2D computational fluid dynamic (CFD) model was developed for the gaseous reduction of iron ore fines in an innovative reactor-multilayer moving-fluidized bed. The solution of the proposed model was performed by integration of FLUENT and PHOENICS. Numerical results of cold state were compared with the experimental data and the agreement between them was good. A hot case-gaseous reduction of iron ore fines using syngas with this reactor was simulated using the present CFD mode. Results indicate that under the given simulation conditions, total pressure drop is 90 Pa less than that under cold state though the gas supply rate is increased about 4m3 under hot state. Gas temperature decreases from 1073 K at the bottom to 500 K at the top, Utilization efficiency of the gas reduction potential is about 27 %. For ore fines reduction, the final reduction fraction could reach 0. 70 and solid temperature 900 K.IntroductionWith the development of coal gasification technology, various coals could be converted to Syngas with air or steam. Therefore gaseous reduction of iron ore fmes becomes an acceptable alternative process for iron making besides blast furnace route[!] and moreover it still has some advantages in processing low grade iron ore fines[2]. Gaseous reduction using fluidized bed technologies is the most competitive in all direct reduction iron-making processes up to now. It has the advantage that ore fines can be directly charged to the process without prior treatment while its disadvantages are particle agglomeration and high gas/solid ratio[3]. To avoid these advantages, a new reactor, multilayer moving-fluidized bed reactor has been developed for carrying out the gaseous reduction. Hydrodynamic behaviors of gas and fines in the reactor were studied and the results were satisfying[4]. However, due to its unique structure of the multilayer moving-fluidized bed and unique gas-solid flow pattern, models of multiphase flow as IPSA, DPM and Eulerian Model could not give a satisfying solution. The current paper is developed a new CFD model and a new solution approach for simulation of the reactive gas-solid flow in the multilayer moving-fluidized bed for its optimization, design improvement and future scale-up."

Jan 1, 2013

By R. G. Reddy

Viscosities of alkaline metal oxide-silicate melts were estimated using our previously developed mathematical model. The structural based model considers depolymerization effects and related breakdown of the silicate network structure, on the addition of metal oxides to the melt. The developed expression: n =4.9x10 9 NO 0 T ½ exp(E/RT) poise was used to calculate the viscosities of various binary silicate systems such as, CaO-SiO,, MgO-SiO, and MnO-SiO,, as a function of temperature and composition. Excellent agreement was obtained between the calculated and experimentally determined viscosities.

Jan 1, 1991

By Cleusa Cristina Bueno Martha de Souza

Nowadays in Brazil the final disposal for spent batteries include sanitary and industrial landfill for hazardous waste from domestic waste and industrial waste respectively. The problems of environmental impact caused by spent batteries had been discussed of several years, considering the fact of metals contents, like Cd, Hg, Pb and Zn. Some techniques are been proposed for recycling this type of waste in order to protect the environment while bringing also economic advantages of recovering metals. The reclamation of metals from secondary raw materials had been employed and further applications of this flexible technology are planned to the future. The processing of metals solutions involving hydrometallurgical techniques is an efficient method for recovering metals, since it provides completely recovery of metals with low energy requirements. This paper discusses the spent alkalline batteries characterization and leaching stage experiments results with sulphuric acid as leachant. After batteries dismantling by mineral processing techniques, the black powder sample produced was submitted to diffraction X-ray characterization and atomic absorption spectrophotometry in order to verify all the substances presented. Some experiments were carried on to develop a hydrometallurgical process for initial metal recovery aiming to get Zn into a soluble form on aqueous solution in order to propose the next stages of purification and recovering Zn, as electroplated deposition. The sulphuric acid was chosen not only for being cheaper than other leachants but also for improving the extraction of soluble Zn as ZnS04 form at diluted acid concentration. Batch laboratory experiments leaching procedure were conducted to determine appropriate leaching conditions from the viewpoint of maximize zinc extraction. In these tests an amount of dry powder batteries was added to different acid concentrations and solid/liquid ratio and after leaching and filtration the aqueous solutions were submitted to atomic absorption spectrophotometry analysis to verify the Zn content.

Jan 1, 2000

By Minjun Tang, Jianfeng Zhou, Feng Chen, Linjiang Qing, Xiaolei Song, Yufeng Guo, Tao Jiang

"Reduction swellability index (Rsn and low temperature reduction disintegration index (RDI) of vanadium-titanium magnetite oxidized pellets are harmful to the processing of ironmaking, for example, causing serious gas permeability, decreased yield, higher coke ratio and more furnace dust. Thus, the improvements of RSI and RDI of vanadium-titanium magnetite oxidized pellets were investigated in this paper, including the pretreatment of raw material, additives of dolomite or boric acid, pellets treated in chloride solution and so on. The results showed that damp milling as pretreatment and boric acid added in pelletizing were conducive to the RSI which decreased 5% and 7% respectively, while they were not efficient enough in improving RDI. Dolomite was efficient in improving RSI, but had negative effect on RDI. There was no evidence to show that RSI and RDI would be improved when pellets were treated in chloride solution. Pursuing this further, the mechanism of those improvements were investigated.IntroductionIn the world, vanadium-titanium magnetite utilization is investigated around how to recover iron, titanium, vanadium, and divided into blast-furnace method and non-blast-furnace method according to respective characteristics. Blast furnace method [1, 2] can recover iron and vanadium effectively, but Ti02 cannot be recycled. Non-blast-furnace methods include rotary kiln-electric furnace method, pre-reduction electric furnace method, reduction- grinding method and sodium vanadium-rotary kiln-electric furnace method and so on. [3-7]Comparing to the Non-blast-furnace method, the method of blast furnace smelting has been put into industrial applications. And it has the following advantages: First of all, effective recycling iron and vanadium; Second, technical problems of high titanium slag in blast furnace smelting; Third, it has mature technology in blast furnace smelting."

Jan 1, 2013

By C. Geenen

At its Olen site, Union Minière Copper operates a new full-size deposit tank house. A first 200,000 t/y module was commissioned in October 1996, and an additional 130,000 t/y unit started in April 1998. The main objectives of the new tank house project were to produce grade A cathodes starting from anodes with a wide range of compositions and at a minimal operating cost. The tank house uses Isa Process technology. Based on the process parameters agreed upon with MIM, UM Copper developed the basic design and UM Engineering was the in-house contractor for the engineering. The new tank house is equipped with advanced technology polymer concrete cells, automated two-bale cranes and high-capacity machines. The first 200,000 t/y module treats anodes with a more conventional composition at 330 A/m2; the second 130,000 t/y module treats anodes with a high slimes fall (12- 13 kg/t) at current densities up to 285 A/m2. After some teething problems, the new tank house is meeting all set targets. This paper illustrates and comments on the design characteristics and operational results.

Jan 1, 1999

By A. J. van der Zeeuw

The use of SME 529 in the extraction of copper from acidic liquors and of copper and nickel from ammoniacal solutions, is illustrated with results of laboratory and bench scale mixer/settler experiments. Special features of SME 529 are its high loading capacity and the ability to keep the complexes dissolved in the organic phase up to quite high concentrations.

Jan 1, 1976

By M. M. Kim

Zn-27% Al was pressure infiltrated into a column of 20 micron diameter abrasive grade SiC particles to give billets with particle loading of 50 voli.une %. Some billets were heated to a temperature where they became semi-solid and diluted with liquid Zn-27% Al alloy to give billets with particle loadings of 12 and 16 volume %. Some of these billets were then extruded into wire with an area reduction of approximately 98%. Tensile properties of the as-cast billets were always inferior to those of the matrix alloys; however, the extruded composite samples showed at 37% improvement in ultimate tensile strength compared to their extruded conventional counterparts. The fracture surfaces of these samples are described.

Jan 1, 1990

By S. S. Ryu, J. C. Kim, H. Lee, Y. D. Kim, I. H. Moon

"Recently, W-Cu alloy becomes one of the very important candidate materials for heat sink and packaging in the field of microelectronics due to its good thermal properties. The metal injection molding of W-Cu powder can satisfy the requirement for mass production of complex shaped parts in microelectronic devices. In the present study, the application of MIM process to the nanostructured W-Cu powder prepared by mechanical alloying was investigated. The multi-component binder system of 45PW+ l 5BW+ 30PE+ I OSA was proven to be suitable one for the MIM of the W-Cu composite powders by adopting the debinding cycles of multi-stage in N2 and H2 atmospheres. Other process conditions for the MIM of the nanostructured W-Cu composite powder were also studied. The MIM debinding part of W-30wt.%Cu was sintered to the relative density of more than 96% by sintering at 1200 °C for !hour in H2 atmosphere. Such an improvement of sinterability was attributed to the intrinsic homogenous and fine mixing state of W-Cu phases in nanostructured W-Cu composite powders, and also partly to the effect of the activated sintering by the presence of impurity introduced during the extensive milling.IntroductionW-Cu alloys have been widely used for heavy duty electrical contacts and arcing resistance electrode(1-2). Recently there has been a growing interest in this W-Cu alloy because of its superior thermal managing properties and its high micro wave absorption capacity(3). Such W-Cu alloy parts are conventionally fabricated either by the Cu infiltration sintering technique or by hot pressing of W-Cu powder mixtures. However, these conventional PM techniques are hardly applicable for mass production of small size parts with a complicated shape such as the parts required for microelectronic devices. The metal injection molding(MIM) technique is potentially applicable for the mass production of small and complicatedly shaped parts compared with other PIM forming techniques."

Jan 1, 1998

By Milorad Cirkovic, Mile Bugarin, Vlastimir Trujic

"Industrial scale testing was performed in the plant-site of Bor Company. Charging sample was from 4-5 tons for each particular test. All operations in industrial scale investigations were carried out in one furnace. For the aim of successful realization of experiments, and primarily for safety and prevention the risk of toxic contamination the working environment, a plant was designed and constructed for cooling and wet dedusting of gases formed during smelting process, zinc removal and flame refinement of molten metal. For the requirements of industrial investigations a complete plant for cooling and wet dedusting of gases has been constructed for brass scrap processing. In this plant, the original ultra-sonic water spraying devices have been installed. The efficiency of such simplified system for gas treatment has been 98,6%. Introduction Permanent development of techniques and technology causes formation the considerable quantities of secondary raw materials that are much more relevant as the raw material base for many metals. Due to a fact that large quantities of metal, are concentrated in the waste materials, large consideration is given to this topic, and numerous technologies for this waste recycling are developed in the world nowadays. High energz price and permanent increase of metal price on the world market have made that secondary raw material tretament, for the aim of various metals production, becomes more and more relevant in the world. In comparison of metal production using enrichment and metallurgical treatment of primary raw materials, the non-ferrous metals production from secondary raw materials has a range of advantages, as well as: - Low level of capital investments, - High technological recovery of qualitative secondary raw materils, - Considerably low consumption of energetic resources regarding to the treatment of primary raw materials (ore and concentrate), - Reduced consumption of unrecoverable mineral resources, - Reduced enviroment pollution [1,6]."

Jan 1, 2008

By Shaik Jeelani, Esperidiana A. B. Moura, Vijaya K. Rangari, Roberta A. Lima, Rene R. Oliveira

This work present the preparation and characterization of biodegradable nanocomposites based on aliphatic-aromatic copolyester (PBAT)/polylatic acid (PLA) blend reinforced by TiO2 nanoparticle. The biodegradable polymeric nanocomposites were prepared by melting extrusion process using a twin-screw extruder machine. The influence of the TiO2 nanoparticle addition on mechanical and thermal properties of PBAT/PLA blend was investigated by tensile and impact tests, SEM, DSC and XRD analysis and the correlation between properties was discussed.

Jan 1, 2015

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Nils Eivind Kamfjord, Roar Jensen, Ingeborg Solheim

"SINTEF has carried out several pilot scale silicon process experiments in the past, but always with an open off gas system. In order to test the possibilities in running a semi closed furnace operation, a new off gas hood has been designed and tested. The off gas hood is designed to collect all off gases to gain insight into the phase compositions in the off gas and at the same time have the opportunity to monitor and maintain the charging/stoking of the furnace. The furnace hood has regulation and control of the air inlet into the combustion zone in two different heights. The off gas temperature and composition was continuously monitored and analyzed during the experiment. In order to expand the knowledge on NOx- formation in silicon metal production, such information is vital.IntroductionBecause of the negative environmental impact, the attention towards all kinds of NOX emissions increases in Norway. The authorities’ demand towards better surveillance and control of emissions increases as well.Earlier and new industrial measurements in FeSi- and Si-metal furnaces reveal quite high NOX-emission. The measurements also show that the NOX formation (mainly as thermal NOX) is distinct connected to the formation of dust (SiO?SiO2) in the combustion chamber above the furnace surface, when the temperature is high and the access to N2/O2 is good. This means that stoking, charging and temperature straight above the furnace surface is important factors for the NOX formation."

Jan 1, 2012

By De-qing Zhu, Zi-fu Gao, Jian Pan

"In order to produce high quality metalized products and prevent from burden cohesion during pre-reduction, self-fluxed pellets were made for COREX process in the paper. The effects of reduction temperature and reducing gas composition on pre-reduction behaviors of self-fluxed pellets are studied. The results show that the prereduced pellets have poor quality and deposited carbon appears when the reduction temperature is between 600°C and 700°C. The metallization rate, reduction degree and compressive strength of prereduced pellets are promoted by the elevating reduction temperature and mole fraction of H2. Pellets reduced by pure H2 at 800°C have high metallization rate (96.2%), reduction degree (99.4%) and compressive strength (960N/pellet). In all tests, self-fluxed pellets display normal swelling (RSI<l5%) behavior which reveals that self-fluxed pellets are suitable for COREX process. Increasing reduction temperature and mole fraction ofH2 in reducing gas is benefit for pre-reduction of pellets.IntroductionCompared with Blast Furnace, the COREX process has advantages of short flow sheet, using non-coke coal and high-energy utilization. Acidic pellets and lump ores are the chief iron- bearing burden for COREX process which could lead to low melting point substance appearing in per-reduction process. In addition, the acidic hematite pellets tend to swell during the reduction [1-3]. This will result in decreasing compressive strength of pellets, burden cohesion, bad air permeability and poor work status in shaft furnace. Adding carbonate flux could restrain burden bonding to some extent in actual production, but decomposition of carbonate flux increases energy consumption. Worse still, weak reduction potential is unfavorable to iron material reduction [ 4, 5]."

Jan 1, 2013

By Rune Gammelsmter

Turbulent chemically reacting flows are generally very complex, involving interactions of chemical, thermodynamic, and fluid mechanical processes. A combustion model based oh algebraic moment closure has been developed. The model is applicable for reaction rates where the chemical kinetics can vary from slow to fast. The effects of turbulence is taken into account by means of modifications to the well known k-e modelling procedure. The model is applied to an industrial combustion process. Calculation of furnace off-gas combustion from an aluminum reduction cell has been performed. The theoretical results agree well with experimental values.

Jan 1, 1992

By A. Martins, L. Goulart, E. Araujo, R. Batista, A. Costa e Silva

Steel cleanness is of great importance to the performance of almost all steel products. From very clean steel for bearings to long products used in civil construction, processing variables – in special those in steelmaking operations- must be properly balanced to achieve adequate cleanness for the desired performance. With the present complexity of steels as alloy systems, it is not efficient nor appropriate to develop these processes on empirical basis alone. Computational thermodynamics can greatly improve process development to achieve the desired cleanness level at reasonable costs. In this work, examples of these calculations and their applications to real steel processing are presented and discussed. The advantages, limitations and areas in which improvement in these calculations is desired are highlighted and discussed.

Jan 1, 2015

By Zuoren Huang

The flowsheet of the hyd.rametallurgical zinc plant which is in use at Zhuzhou Smelters is described. The principal features of the process are fluid bed roasting, continuous calcine leaching, solution purification, zinc electrolysis, electrolyte cooling, and finally, the melting and casting of zinc forms. The Zhuzhou process for the flotation of silver from the leach residue collected on the Moor filters is described. The technical details of the process are outlined and the operating data are analyzed. The flotation facilities are described in detail and concentrate grades and recoveries are presented. The waelz process is used to concentrate In, Ge and Ga remaining in the leach residue after silver flotation. These elements subsequently are recovered by selective leaching in sulphuric acid, and details of this operation also are presented.

Jan 1, 1990