Search Documents

By SIMON TIMBILLAH

The chalcopyrite-molybdenite (Cu-Mo) flotation industry is increasingly turning to organic depressants as suitable replacements for inorganic reagents, such as NaHS, due to environmental and safety concerns as well as high consumption rates of the inorganic reagents. This presents an opportunity for improvements or design and synthesis of alternative reagents. Disodium carboxymethyl trithiocarbonate (Orfom® D8) depressant is an organic depressant with a carboxylate group on one end and a trithiocarbonate group at the other end. Fundamental results are shown regarding the interaction of the Orfom® D8 depressant in the bulk flotation of a Cu-Mo concentrate from an operating North American mine. Cyclic Voltammetry on pure copper and Fourier Transform Infrared Spectroscopy (FT-IR) and X-ray Photoelectron Spectroscopy (XPS) measurements on pure chalcopyrite with Orfom® D8 depressant treatment are also reported. Through such characterization techniques a potential adsorption mechanism of Orfom® D8 on the mineral surface was identified and its depressant characteristics in the Cu-Mo flotation systems explained.

By Xia Lou, Hossein Dashti

Gas hydrates technology has been considered as an alternative method for carbon dioxide (CO2) separation. A wide range of studies have been reported in the past decade on the improvement of the separation efficiency by using chemical additives. While most of these studies have shown improved kinetics, thermodynamics and/or separation efficiency at the laboratory scale, there has been no quantitative analysis of the energy consumption for viable industrial applications. Comparison of the effectiveness of the chemical additives from separate studies or groups also is impossible. The present work is focused on the modelling of the hydrate-based CO2 separation process and provides a quantitative approach that is new in its analysis of the effectiveness of chemical additives in relation to the energy required and the kinetic parameters involved in the process.

Mar 1, 2018

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By Roland Loewen

A review of the aqua regia method for the recovery of gold from jewelry shop wastes is given. Also outlined is a specialized procedure for the recovery of the silver that occurs in these wastes. A classic method for the recovery of platinum and palladium is, given. There is a brief review of other gold and silver refining methods. Environmental conditions are discussed and a few perhaps, new and useful processes ,are mentioned. References are by author or editor and are listed alphabetically. Suggestions for further information in the field of precious metals, are given in a final list.

Jan 1, 1989

By Djona M. Gaballah I.

Selective chlorination of unroasted and roasted spent hydrorefming catalysts was studied between 300 and 600°C using the following gas mixtures : C12+CO, C12+N2 and CI2+air. Such materials contain Co, Ni and Mo compounds supported by alumina and/ or silica. They also contain variable amounts of V compounds, C, S, etc., accumulated during the life time of the catalyst. Direct oxychlorination of the C+S rich sample allows higher extraction rates than those obtained by the carbochlorination of the same roasted one. It seems that the roasting step doesn't favor the economic metals' recovery. Results of the chlorination of C+S poor spent catalysts, in the presence of CO, in the chlorinating gas mixture, or of carbon added to the sample, were comparable. Cobalt and nickel chlorides were .extracted from the chlorination residues by their dissolution with acidified water, whereas molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The recovery rates of valuable metals as well as the selectivity were higher for the chlorination of spent catalysts than results obtained by the hydrometallurgical processing of the same sample. Results of the scale-up of the oxychlorination of the unroasted sample confirmed those of the laboratory scale. The global recovery rates were about 88 pct of cobalt, 93 pct of molybdenum and 76 pct of vanadium. The carbochlorination was applied to the recovery of W and Ti from Denox catalyst that is a carbon and sulfur free one. Recovery rates higher than 99 pct at temperatures lower than 500 °C could be obtained. This may indicate that the chlorination process can be applied to the treatment of various industrial wastes or by-product containing transition and/or refractory metal compounds A flow - sheet for the pretreatment of these materials is proposed.

Jan 1, 1995

By Cajsa Samuelsson, Theo Lehner

Converting and refining play a central role in the extraction of metals. Sweden has a long tradition as an experimental play ground for metallurgists, chemists and alchemists, developing new methods and technologies. Presenters of papers are usually happy in recording successful developments. But reporting failures can be as great a value as the former. In the paper experiments and experience in process development are illustrated, differences between ferrous and non-ferrous developments are highlighted and industrial learning curves are discussed. 53

Jan 1, 2009

By Elaine Araújo

Since the ancient times, clays were used as decolorant material for various types of oils. These clays were called ?decolorant clay?. They have the property to decolor dye materials present in mineral oils, plants and animals. Biofuel is a fuel derived from biomass of live organisms. As biodiesel is produced from renewable sources, the generation of employment due to industrial scale production may cause a reduction in the dependence on foreign diesel importing, as well as the reduction of air pollution by the addition of biodiesel to diesel. This study aimed to develop a technological process to decolor post- consumption oil to be applied as biofuel. The results were characterized by techniques of XRD (X-ray diffraction), X-ray fluorescence and FTIR (Fourier Transform Infrared). It was observed that the post-consumption oils presented a higher decoloration result after treatment with the Brazilian clay.

Jan 1, 2009

By Chang-Dong Li

Cadmium ingot and nickel powder were prepared by high-temperature distillation, solvent extraction and liquid phase reducing method with spent Cd-Ni batteries as raw material. The impacts of the temperature in the distilling stage, the concentration of H2SO4 in the leaching stage, the pH value in the extracting stage and the dosage of hydrazine in the reducing stage were discussed respectively. The as- prepared samples were characterized by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results showed that the recovering efficiencies of Cd and Ni reach 99.5% and 99.3%, and the purities of Cd ingot and nickel powder were higher than 99.90% and 99.80%, respectively.

Jan 1, 2009

By Felipe Costa Hashimoto Bertin, Jorge Alberto Soares Tenório, Rodrigo de Souza Dalti Pereira, Denise Crocce Romano Espinosa

"The increasing amount of portable devices and their fast obsolescence generates an increasing quantity of discarded batteries. The recycling process of discarded batteries allows the recovery of metals for further use and avoids the contamination of soil and water. Even though there are several researches on the topic, few papers focus on mixed batteries. The purpose of this work is to characterize a mass of collected mixed batteries and study the hydrometallurgical process of recycling. The specific leaching parameters studied were pH, temperature and reduction potential. The specific goal was testing the selectivity of pH for leaching each metal. The results show that the optimal leaching occurs in acid solutions with negative pH at IM of sulfuric acid and at room temperature (25°C).IntroductionThe increasing portability of electronic devices in the past century along with their fast obsolescence produce tons of discarded materials yearly that could be recycled generating new materials for the industry. For example, metals such as cobalt and nickel, that are worth respectively US$ 30.00 and US$ 16.10 per kilogram[l,2] are disposed in urban trash yearly, which means that millions of dollars are thrown away instead of being recovered and reused[3].Besides the obvious fact that the society is throwing money away, most of these metals are toxic for the environment and all mammals, so when badly stored after use they can be found contaminating ground water which will contaminate the entire lifecycle. Some of these metals can cause cancer, serious lung problems and have bioaccumulative properties [4] resulting in lower productions of natural products and maybe death for consumers.So in compliance to new regulations such as the National Solid Residue Politic (PNRS) and the CONAMA-Resolution N°401 from November of 2008[5]- (that follows similar restrictions and regulations as the European directives) all those urban and electronic wastes need to be correctly disposed and treated before being thrown away on local dump sites.In Brazil the national rate of garbage recovery is around 70%, which only 5% is properly recycled, accordingly to the research of the UFSC, also electronic waste grows at 5% per year [6]The present study was motivated by the fact that recycling processes for batteries are not spread through the country and by the fact that most papers do not try to recycle a mixed mass of batteries, but a specific mixture which does not represent the composition of traditional household wastes."

Jan 1, 2014

By Youze Xu

The leaching and reduction of Cr(VI) in soils contaminated by chromium-containing slag were investigated with column experiments. The results showed that Cr(VI) concentration in leachate decreased from 988 mg L-1 to 407 mg L-1 after 7 days when water was used as leaching agent. However, Cr(VI) in leachate in culture medium treatment was not detected at above periods. In comparison, Cr(VI) concentration in leachate from autoclaved soil remained 398 mg L-1 at the end of experiment. The results indicated that the indigenous microorganism was capable of reducing Cr(VI). The amount of Cr(VI) reduction was 335 mg at the whole experiment period and the reduction rate was 67.09 mg d-1. Carbon supply showed minor effect on Cr(VI) reduction. However the reduction capability of Cr(VI) could be improved by combination of the carbon and the nitrogen. The optimal quantity was 5 g L-1 of yeast extract and 4 g L-1 of glucose.

Jan 1, 2009

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By Qiang Guo, Zongliang Zuo, Mengqi Wei, Qingbo Yu, Qin Qin

Activated carbons, derived from waste ion-exchange resin by CO2 physical activation, were applied to separate CO2 from flue gas against global warming. The BET specific surface areas of activated carbons at different activation temperatures and times were investigated. The CO2 adsorption capacity was tested under non-isothermal and isothermal conditions. The experimental results show that when keeping the activation temperature constant, the specific surface area increases firstly and then decreases with increasing activation time. For the given activation time, the specific surface area rises firstly and then declines with increasing activation temperature. The adsorption capacity decreases with increasing temperature. The maximum adsorption capacity is 51.46 mg/g under the condition of 298 K and pure CO2. Fractional order kinetic model is the best one to describe the kinetics of CO2 adsorption. The activated carbons show the potential to be an effective adsorbent for the removal of CO2 from flue gas.

Mar 1, 2018

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By C. G. Bastos Andrade, F. R. Valenzuela Diaz, S. M. Toffoli

The climate change observed in the last decades, the increase of global warming, the melting of the polar ice caps, and the sea level rise have in common the non-sustainable development as causative agent. Different nations have mobilized joint efforts with the objectives of minimizing the impact of greenhouse gas (GHG) emissions, investing in the research and the development of new technologies in recycling, in biomaterials, environmentally friendly processes, and new fuel alternatives. This paper evaluates the efficiency of a Brazilian bentonite modified by acid attack, in the purification step of a waste oil to be used for biofuel production, that is, diesel from waste cooking oil (WCO). The following characterization test swere performed: XRD, CEC, XRF, SEM/EDS, specific surface area (BET), stereomicrography, kinematic viscosity, and spectrophotometry at 440 nm. The modified bentonite exhibited good purification capacity for WCO when compared to a commercial product.

Mar 1, 2018

By WU Jian-hui

Keywords: metallic material, precursor synthesis, precipitation, nickel, fibrillar powder The composition and morphology of the precursor of fibrillar nanocrystalline nickel powder prepared by oxalate precipitation are characterized by XRD,IR and SEM analysis, and the effects of temperature, nickel concentration, pH, surfactant and drying process on the morphology and the dispersion of the precursor are investigated. By the experiment results, the fibrillar precursor is a complicated nickel salt. The precursor prepared in the of 60~70°C,0.6~0.8 mol/L nickel ion, pH=8.4~8.6 and with addition of PVP surfactant is well dispersive and in fiber form. The powder dried by azeotropic distillation is dispersive.

Jan 1, 2005

By Rodney Hundermark

At Anglo American Platinum’s Polokwane Smelter, radar instruments are being used to provide continuous measurement of the concentrate feed level in the six-in-line electric furnace used for smelting of nickel-copper concentrates containing platinum group metals (PGMs). The radar instruments are installed directly on the furnace roof, and a mechanical system has been designed to protect them from radiation and elevated freeboard temperatures and pressures. Signal validation criteria have been implemented to ensure that proper level measurements are being used by the PLC system. The feedback from the radars has provided an improved understanding of the furnace behaviour with respect to concentrate feed level control, individual feeding events, global feed rates, feed distribution and bath disturbances. In combination with a dynamic mass balance for continuous calculation of liquid level in the furnace, the radar measurements have enabled more precise feedback control of the concentrate blacktop depth. In turn this has yielded improvements in furnace stability.

By Na Wang, Chao Du, Yao Zhang Shuqiang Jiao, Hongmin Zhu

"Na2NbAlO5 was synthesized using Nb2O5 and NaAlO2 as raw materials in molten NaCl-CaCl2 by a solid reaction. With an addition of sodium into the melts, Na2NbAlO5 was subsequently reduced to form NbAl3 intermetallic compound with a particle size of 50-300nm.IntroductionThe intermetallic compounds of niobium aluminides have been a subject of research interests as high temperature materials because of their properties such as high melting temperature, large specific strength at elevated temperature, good resistance to high temperature oxidation, low density and large ductility [1,2]. They are applicable for turbine blades in aircraft engines and stationary gas turbines [3,4].In recent years, the methods of powder synthesis have been widely discussed. There are many methods to synthesis intermetallic compounds such as conventional melting and solidification [5], powder metallurgy [6,7], reaction sintering [8] and reaction sintering with prior mechanical activation [9,10]. There is a prominent weakness in such methods that they use metal to produce intermetallic compounds by the means of diffusion reaction. Although the metal can diffusion sufficiently, it is still hard to avoid maldistribution of the constituents which impairs the properties of the materials."

Jan 1, 2012

By Thomas Weyand, Thomas Claridge, Dale Nickels

"This paper addresses the initial results of a project to evaluate the suitability of copper mining tailings as raw material for the production of structural products using PMET’s patented technology. Preliminary testing indicated that high performance structural products were possible using these materials. A demonstration scale project produced approximately 1,500 bricks in various colors. These products fall under under ASTM C- 73 and were found to present properties suitable for severe weather applications. Although the products in this project were of typical brick dimensions, other products are possible, for example concrete block substitutes or pavers. These products from the PMET process are commercially known as Brixx. This paper will provide operational details of the production process, mineralogy and mechanical properties of the products.INTRODUCTIONPMET has developed process technology that can convert various siliceous waste materials into competent structural products. This technology is the subject of US patent # 6,068,803. In general, the process consists of mixing lime, water and the major feed stock, pressing to form a “green” shape, and curing the product in an autoclave for 6 hours with saturated steam at ~200oC. The curing process forms Tobermorite, which acts as a crystalline binder. Freeport-McMoRan approached PMET to see whether mine tailings from the Sierrita mine, containing significant amounts of clay, might be a suitable feed material for the production of structural products. “Brixx” is the commercial term used to describe the resultant structural product formed in the test work. This paper is a preliminary evaluation of a technology that is being considered by Freeport-McMoRan. This report is not an endorsement by Freeport-McMoRan of the process or products, nor is it a commitment to use this technology."

Jan 1, 2008