Search Documents

By Ping Long, Peipei Liu, Xinlin Ren, Yunke Wang, Bin Yang, Jian Wu, Wenli Zhang

In this research, ICP-AES was used for determining ten impurity elements (Fe, Pb, Ca, Mg, Cu, Zn, Al, As, Sb, and Bi)in tin concentrate and smelting products, such as crude tin and slag. Samples were dissolved by hydrochloric acid and nitric acid. Determination conditions were investigated in detail. Influences of matrix and coexisting elements were eliminated by selecting proper analysis spectral lines. Under the optimum conditions, the correlation coefficient of cali- bration curves were higher than 0.999. The detection limits of these ten impurities were in the range between 0.0009 to 0.0621 lg/ml. Relative standard deviation (RSD) values were lower than 6.0%, and the recoveries of standard addition were between 85 and 109%. The proposed method was demonstrated to be reliable by comparingwithstandardanalysismethodsandcertifiedvaluesofstandardsample. It could be applied for determining impurity elements in tin concentrate and smelting products successfully.

Mar 1, 2017

By Patrick R. Taylor

The synthesis of high-purity ultra-fine barium strontium titanate powders (BST: BaO6Sro.4TiO3) has been performed in a non-transferred are D.C. thermal plasma reactor. Slurries of aqueous solutions of dissolved barium and strontium nitrates and solid titanium dioxide powders were used as precursors. Oxygen and argon were used as carrier gases, and pure argon and combinations of argon and nitrogen were used as plasma gases. The plasma torch power was varied, as well as the oxygen flow rate and the total molar concentration of the precursors. A graphite plate was designed to protect the torch electrode and lower the level of impurities in the product. A thermochemical analysis of the Ba(NO3)2-Sr(NO3)2-TiO2-H2O-O2 system was performed to predict the conditions for the formation of BST and the feasibility of the reaction, The powders collected from the different sections of the reactor were characterized using Transmission and Scanning Electron Microscopy, X-Ray Diffraction, and ICP chemical analysis. The powders produced showed high conversion to BST, ultra-fine particle size (< 30 rim) and high purity, which makes this a potential process to produce ceramic materials for electronic devices.

Jan 1, 2003

By Milton Manrique, Edgar E. Vidal, Patrick R. Taylor

"Ultrafine zirconium carbide powder has been synthesized using zircon concentrate and methane in a thermal plasma reactor. The effect of several experimental variables, such as power used and zircon particle size, on the conversion has been studied. A thermodynamic analysis of the possible reactions and stable compounds was performed. A mathematical model that describes the in-flight decomposition of zircon particles was developed based on a description of the temperature and velocity profiles calculated in the reactor. It was shown that the formation of zirconium carbide from zircon and methane is thermodynamically possible. Complete 'vaporization of zircon in the reactor is predicted when the particle size is below 45flm and the effective power entering the reactor is 15 kW. The powders were collected and characterized by XRD, SEM, TEM and chemical analysis using ICP. Results of the product analysis indicated the presence of zirconium carbide, zirconium oxide, silicon carbide and silicon oxide.IntroductionIn recent years there has been an increased interest in the production of nanometric sized powders of ceramic materials for use in advanced materials applications. One possible method to produce these powders is with a thermal plasma reactor, which offers high temperatures and fast quenching rates. This technology has been called - Thermal Plasma Synthesis - [1].Zirconium Carbide (ZrCx) has typical properties of transition metal carbides: elevated hardness - between alumina and diamond - a high melting temperature of 3420°C and high chemical stability at room temperature [2]. ZrCx has a Bl crystal structure with deficiencies in the number of carbon atoms in the cell with x between 0.6 and 1 [3]. Different methods have been used to produce ZrC, one method is by direct reaction of zirconium hydride or halide with carbon. Other methods used are direct reduction and carburization of zirconium oxide (Zr02) and reaction of metallic zirconium with a caburizing gas such as acetylene [3]. Recently small films of ZrC have been obtained using a sputtering device [4,5]. ZrC has been used in nuclear plants as a low neutron absorbing and high mechanical resistant refractory material and also as a constituent in cathodes made of UC-ZrC [6]. It is also used in the form of tubes, boats and crucibles to handle molten metals and as part of electronic devices used for thermoionic transducers. Recently ZrC has been used along with zirconium diboride (ZrB2) to produce composite materials [7,8]."

Jan 1, 1996

By Jesús Contreras

Within its programme for continuous improvement and cultural change, Atlantic Copper has installed the Six Sigma methodology as a basic tool for the improvement of management techniques in all its production centres. Following an implementation period, the methodology is widely used for analysis and improvement, not only in the fields of production and maintenance, but also in other areas of the business such as supplies or energy management. The present paper describes, phase-by-phase, the project that was developed to improve the quality of converter slag through the application of Six Sigma techniques, from the initial set up to the final results obtained.

Jan 1, 2005

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual&apos; usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system&apos;s performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Jeffrey R. Taylor

The distribution of low concentrations of Cr, Mn, Rh, Co, Ni, Ag and Fe between copper matte and bullion phases has been measured at 1200oC. These results. together with values for nine other elements, have been used to develop a simple model to describe the distributions in terms of known thermodynamic properties?. The Temkin model for ionic melts was assumed to apply to the sulphide species in the Cu-S matte? phase and it is shown that the choice of sulphide species is particularly important for successful representation of the experimental .results?. In general, the lowest sulphlde (minimum sulphur :. metal ratio)? formed by the. metal is most suitable, although Ni, Co, Rh and Pd appear to associate with more sulphur in the melt than suggested by the? composition of their lowest sulphide. A correlation between the composition of the metal sulphide species formed in the ternary system and the? position of the minimum in the free energy of mixing curve in the metal-sulphur binary -system is? proposed.

Jan 1, 1983

By T. Gunawansa, T. L. Alford, Zhao Zhao, A. R. Lanz, N. David Theodore

Many sustainability issues arise during the manufacturing processes that are currently used for solar cells. Solar energy is a renewable energy source that is independent of the earth’s resources, and it is therefore important for the development of more sustainable technologies. Microwave annealing (MW) has been proposed as a technically feasible fabrication scheme for large area silicon solar cells. Apart from that, microwave annealing has been demonstrated to be a promising alternative for repairing damage and electrically activating dopants in ion-implanted semiconductors for integrated circuit manufacturing. A microwave oven is cheaper than conventional furnace systems. In addition, microwave heating is much more efficient than conventional furnace heating, as heating is directly produced inside the material. This minimizes the loss of energy due to heating of the ambient. There is a need for more efficient processing techniques. In this study, microwave annealing is used as an alternative to the current postimplantation processing. Arsenic-doped silicon was microwave annealed (with an aluminacoated silicon carbide susceptor) to activate dopant atoms and to repair damage that was caused by ion implantation. Sheet resistance and Hall effect measurements were used to assess the extent of dopant activation. Rutherford backscattering spectrometry (RBS) with ion channeling was conducted to determine the extent of recrystallization. The dopant activation and recrystallization resulting from microwave annealing is compared with that resulting from conventional rapid thermal annealing (RTA) with the same heating profile. The results show that when compared to RTA, susceptor-assisted microwave annealing results in better dopant activation for shorter anneal times under the same heating conditions.

Jan 1, 2015

By S. A. Platias

Large amounts of dunile tailings can be recycled for olivine produdion from the existing beneficiation adivity of chromite ore in northern Greece. This olivine production aims at the preparation of a material suitable for the substitution of the environmental hazardous quartz sand in the foundries of Europe In smelting of chromite ore the losses that occur ore usually of the order of 6-8% Cr that report in the slag. Most of this is in the form of oxides that cannot be recovered, but usually 30-35% is in the form of FeCr alloy that can be recovered by gravity methods. About 90% of the produced slag is sold for road construdion after crushing to a desired grain size. Finally, recycling of chromites sludges from the ferrochrome produdion plant, through the preparation of pellets, improved the total chromite yield by 2%.

Jan 1, 1996

By Robert S. Gärtner

The selective aluminum extraction by 3 different calixarenes (p-tert-butyl-calix[4]arene-tetra¬2-acetic-acid-ethyl-ester, p-tert-butyl-calix[4]arene-tetra-2-acetic-acid and p-tert-butyl-calix-[4]arene-di-2-acetic-acid-ethyl-ester) from an industrial pickling bath solution was studied. The pickling bath solution contained hydrofluoric and phosphoric acid as its main components. The aluminum removal was not successful and also no significant extraction of trace metals present was observed.

Jan 1, 1999

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By Sacha Neven

Submerged lance technologies combine high intensity processing characterized by rapid mixing and reaction rates using a simple reactor design. The Isasmelt technology uses a central submerged lance to inject oxygen-enriched air and fuel into a bath thus creating large gas bubbles and intensive turbulence and splash. The lance is equipped with swirlers to increase gas velocity and heat transfer. This enables the formation of a frozen slag layer on the lance which protects it from the aggressive environment. Water models as well as high temperature reactors were used to validate the Davidson-Schiiler model on bubbling. Frequencies and pressure amplitudes were measured in a wide range of gas flow rates: from m3/sec using a water model to more than 30 m3/sec in an industrial process. Agreement with the model was satisfactory. The experiments however also clearly showed that cross-flow and bubble wake induce slightly higher frequencies. No influence of the use of swirlers on the bubbling frequency was observed in the water models.

Jan 1, 2002

By Yongxiang Yang

High temperature processing of raw materials in metals production and recycling often involves complex multi-phase fluid flow and heterogeneous chemical reactions at various scales. Good understanding of the process physics and chemistry is crucial for process operation and process development. The traditional scale-up process through laboratory scale ? pilot scale ? commercial scale route has been more and more complemented and partially replaced by full-scale process simulation. Computational fluid dynamics (CFD) has become a very useful simulation tool in process research and development. At the same time industrial applications challenge the CFD development with its complex transport phenomena, often in large-scale reactors with small-scale physics and chemistry. The current paper discusses the applications of CFD to a number of high temperature metallurgical and materials processing applications. The research was carried out by using commercial CFD codes as the framework, and the emphasis was given to the special efforts for the development and implementations of sub-models with process-dependent physical and chemical characteristics. To illustrate the application of CFD simulation to high temperature metallurgical processes and coupling of sub-models to the general-purpose CFD codes, five examples are given: (1) melting of aluminium scrap in a rotary furnace for recycling, (2) molten hot metal flow in a heterogeneous coke-bed of a blast furnace hearth, (3) gas flow heat and mass transfer in a submerge electric arc furnace for phosphorus production, (4) high temperature incineration of hazardous waste in a rotary kiln, and (5) transient heating of metals in heat treatment furnaces.

Jan 1, 2006

By Tuula Mäkinen

One of the latest applications of the Outokumpu Flash Smelting Technology is the direct smelting ,of nickel concentrates to metallised low-iron nickel mattes. Compared to the conventional nickel smelting, the new DON process needs a lower number of smelting vessels resulting in considerable economic and environmental benefits. Fundamentals of smelting nickel concentrates in one stage to low-iron mattes are presented. Properties of nickel. smelting slags with an emphasis of the slag fluidity at high MgO-levels are also discussed. Conditions prevailing in DON mattes at high oxidation degrees are presented as well as their influence on the behaviour of such mattes in the settler and on tapping the furnace. Distributions of elements in the direct smelting are presented and compared with the conventional process. A further comparison is made with pilot-plant data and the industrial scale.

Jan 1, 1998

By Jörn E. Fischer

Cracks were observed at the top of spray formed billets for some alloys. In this paper the effect of process parameters on crack probability is discussed. After the spray run the thermal conditions at the top of the billet change rapidly. A hot spot with melt residue] can occur inside the billet and shrinkage will be suppressed due to the solidified surface of the billet. In this situation hot cracks can be initialized. The temperature history of the billet during and after the spray run is calculated. The temperature difference between core and outside diameter of the billet is taken as indicator for hot crack probability. The effect of different process parameters on the hot crack probability is discussed. The results lead to a better understanding of the process. The calculations are taken as a tool to find process parameters in order to reduce or avoid hot cracks in spray formed billets.

Jan 1, 1999

By Stanko Nikolic

Ferrous calcium silicate slags are potentially important for future practice in copper converting operations and processes and can be described by the ?Cu2O?-FeO-Fe2O3-CaO-SiO2 system. Despite its industrial importance the phase equilibria in this system have not been fully investigated. Characterization of this slag system is necessary to improve the design and optimization parameters of new processes, including fluxing and operating temperatures. Experimental methods have been developed to investigate the phase equilibria of these slags at copper saturation and without copper. This technique involved equilibration of samples at a fixed oxygen partial pressure, rapid quenching, and analysis of the compositions of phases using electron probe x-ray microanalysis (EPMA). Liquidus and solidus data are reported for the primary phase fields of spinel, wollastonite and tridymite at 1250oC and an oxygen partial pressure of 10-6atm. The resulting data has been used to construct liquidus isotherms in the ?FeO?-CaO-SiO2 system both in equilibrium with and without molten copper. The experimental results were compared with the predictions of a thermodynamic computer package utilizing a self consistent thermodynamic database. The predictions of the model were in good agreement with the experimental isotherms when projected onto the FeO-CaO-SiO2 section, however the copper concentrations in the liquid phase at copper saturation were lower than predicted using the current database of the model.

Jan 1, 2006

By Xingye Guo, Yeon-Gil Jung, James Knapp, Zhe Lu, Jing Zhang, Li Li

La2Zr2O7 is a promising thermal barrier coating material due to its low thermal conductivity and superior high temperature stability. In this work, Bilayer La2Zr2O7 and conventional 8 wt% yttria stabilized zirconia (8YSZ) coatings were deposited using plasma spray technique. Both singlelayer La2Zr2O7 and double-layer 8YSZ/La2Zr2O7 coating architectures were designed. Thermal cycling and thermal shock tests were used to evaluate coatings’ thermomechanical properties. All La2Zr2O7 coats were delaminated in the furnace cycle test in less than 20 cycles. This is because residual thermal stresses accumulated during thermal cycling. In the jet engine thermal shock (JETS) tests, the SCL La2Zr2O7 and DCL dense 8YSZ/La2Zr2O7 coatings were fully delaminated. In contrast, the DCL porous 8YSZ/La2Zr2O7 coating sample only partially delaminated on the edge. This is because of the porous 8YSZ layer provides strain compliance. The findings will help to propose efficient thermal barrier coating systems.

Jan 1, 2016

By Tao Li

The development of DP(Dual Phase) steels and TRIP(Transformation Induced Plasticity) steels has received much attention in recent years due to their high strength and simultaneous good ductility, which provides the potential for weight reduce and resource savings on certain components in automobile or other industries. So a controlled rolling process was simulated in the present study by thermomechanical simulator (Gleeble 1500) for producing DP steels on a kind of low carbon steel containing a small amount of Si and Cr. F+M dual phase microstructures have been obtained during continuous cooling processes of a wide cooling rate range from 10°C /s to 60°C /s. The grain size of the dual phase steel developed can be refined to less than 5 m through the mechanism of deformation induced ferrite (DIF) transformation. The ultrafine ferritic grains are equiaxed with high-angle boundary, and the martensite islands of an average size less than 5m disperse uniformly in the ferrite matrix. The ultrafine martensite islands not only inhibit the growth of ultrafine ferritic grains and improve the bonding of F/M interface, but also increase remarkably the strain hardening rate in the processing of the present Dual-Phase steel. As a result, the tensile strength of ultrafine grained Dual-Phase steel reaches higher than 1000 MPa. The result shows that an ultrafine grained Dual-Phase steel of low carbon and low alloy is promised to exhibit desired F+M microstructure by means of this new TMCP process.

Jan 1, 2006

By Suswnu Makino

Sumitomo Metal Mining developed a new nickel refining process ( Matte Chlorine Leach Electrowinning process) based on chlorine leach and electrowinning technologies. After the pilot plant study, the commercial plant with design capacity of 24,000 tonnes per year was constructed and has been successfully operated since August, 1992. During the practice of the past three years, great deals of improvement have been achieved. Through these operations the MCLE process has been demonstrated to be one of the most superior processes in the world with nickel recovery, productivity, cathode quality and working environment. Today the refinery product capacity is increased to 30,000 tonnes per year. This paper describes the equipments and operation of the Sumitomo MCLE process.

Jan 1, 1996

By A. Onozaki

The Iijima Refinery was put into operation in 1972 and today has an annual production capacity of 156,000 tons of SHG electrolytic zinc. At the Iijima Refinery, the recoveries of gold and silver are 98.0% and 98.2%, respectively. Gold contained originally in the zinc concentrates reports in the Cu-Pb-Ag residue produced in the residue treatment process. Silver contained in the concentrates is distributed between the Cu-Pb~Ag residue and the copper cake produced in the purification process. The Cu-Pb-Ag residue, which contains gold and silver, is sent to the Oyachi flotatfon plant of the Kosaka Smelter; about 82% of the gold and about 85% of the silver are recovered in the copper flotation concentrate.. In this paper, the distribution of gold and silver in the Iijima. Refinery is discussed and operational results of the Oyachi flotation plant are presented.

Jan 1, 1990

By Courtney A. Young

All cyanide species are considered toxic and can be found predominantly in industrial effluents generated by metallurgical operations. For example, cyanide&apos;s strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent water contamination. Various methods of cyanide remediation by separation and destruction are available, but certain methods are more effective than others depending on the cyanide species being remediated. Photolytic destruction is regarded as the one technique that is independent of the cyanide species involved. The destruction of various cyanide species by several photolytic techniques has been investigated for the past few years. A literature survey suggests heterogeneous photocatalysis with anatase (TiO,) should behave similarly to homogeneous photolysis with hydrogen peroxide (H,O,) since proposed reaction mechanisms for both processes involve hydroxyl radicals. However, experimental evidence on a suite of cyanide species suggests otherwise. A new mechanism for the photocatalytic destruction of cyanides, especially SAD species, is therefore proposed.

Jan 1, 1998