Search Documents

By Kenji Monden

A simple technique is presented to evaluate optical property of biomimetic microlens array (BMA) as an antireflective surface on a polydimethylsiloxane (PDMS) sheet. The integration of these structures is done by a thermoforming process. We have only UV-VIS spectrophotometer for optical evaluation apparatus. The transmittance of the sheet is measured with angled sample holder. The 50 deg. transmittance of 270nm pitch BMA on PDMS sheet increases from 87 to 92% after the moth-eye structure is introduced. The transmittance of 350nm pitch BMA on PDMS sheet increases from 87 to 96% after the moth-eye structure is introduced. The transmittance increases with increasing pitch of BMA. The results obtained using UV-VIS spectrophotometer with handmade sample holder.

Jan 1, 2015

By John C. Carpenter

Solvent extraction is used to selectively recover copper from iron containing sulphate solutions. As chloride ions, which form series of complexes with transition metals, are now being used for leaching. Little is known of the effects of these ions, on solvent extraction behavior. It has been shown that commercial extractants of the L1X and Kelex series extract copper from chloride media: (1) at a lower pH than from sulphate solutions, (2) to similar loadings, and (3) except for L1X 63, without transferring chloride to the organic phase. A process for selective extraction of copper from chloride solutions should thus be compatible with standard stripping and electrowinning practice. Of several diluents, differing in aromaticity, kerosene gave enhanced extraction only with L1X reagents. A change in operating temperature had little effect on equilibrium metal distribution. All the extractants examined gave adequate separation of copper from iron. L1X 63 was found to extract chloro-complexes of copper and of iron and thus transfer chloride to the organic solution. Consequently this extractant and its mixtures are not preferred for use with chloride leaching systems.

Jan 1, 1976

By Volker Uhlenwinkel

The design of a free fall atomizer as well as the process parameters affect the particle mass flux distribution in the spray cone. The mass flux distribution is important in spray forming because of its influence on the deposit shape and enthalpy input into the deposit. In this article the effect of different process parameters on the mass flux distribution is shown. Furthermore, different melts were atomized with the same atomizer. An empirical correlation will be introduced to predict the mass flux in the spray cone. This correlation will be compared with experimental results.

Jan 1, 1999

By Francis C. Furman

Microscopic evidence indicates that the high sinterability of certain commercial dolomites is tied to specific dolomite textural characteristics. This study encompasses detailed characterization of the unprocessed dolomite and sintering doloma results. The chemical and mineralogical compositions, insoluble residue, chemistry homogeneity, crystal size, primary carbonate texture, secondary dolomite texture, deformation structure, porosity type, porosity, and density of the raw dolomite were observed. These characteristics are compared with sintering trials of <74um powder-compacts samples in which holding times were varied. The evolution of the dolomite characteristics are reviewed and related to the final sintered doloma characteristics. The critical characteristics of a single-stage sintering brick dolomite are the following: 1) primary oolitic texture, 2) dolomite purity, 3) dolomite stoichiometry 4) minimal impurities, less than 1 weight {%} Fe2O3 Al2O3 and SiO2, 5) chemical homogeneity, 6) high density, 7) very low porosity, S) very coarse homogeneous crystallinity, 9) nonplanar dolomite texture, 10) abundant strain related slip microdeformation structures, 11) minimal subsequent alteration. Even with grinding to <74um the nonplanar dolomite texture and slip deformation still have a major effect on doloma sintered density. The three newly identified characteristics of single-stage sintered refractory brick dolomite are their primary oolitic texture, secondary nonplanar texture and abundance of stress related microdeformation structures. The primary oolitic texture reflects a homogeneous pure carbonate with respect to chemistry and crystal size secondary nonplanar texture produces crystals with large surface area to volume ratio. Stress related slip deformation moves CO, groups in to the same site of another CO, group but different orientation which is very unstable. All of these characteristics may facilitate the formation of higher density dolorna sinters.

Jan 1, 1995

By C. W. Vierrether

Mineralogical analysis contributes directly to the selection of applicable beneficiation techniques for a given site. Tentative remediation methods for use on the Sharon Steel tailings in Midvale, Salt lake County, UT, were determined in part by mineralogical characterization. A systematic characterization scheme was employed to identify mineral species, mineral associations, and grain size. This paper presents the mineral content and distribution data collected for site characterization. This data was used to determine areas that were representative of the total tailings at the Sharon Steel site. Although this was the main focus of characterization, other useful information was obtained. The approximate location of "old jig tails" was identified and insight on possible arsenic, mobility through the pile was also obtained from the mineralogical study.

Jan 1, 1991

By WenCai Li, Yong Ren, Shuai Niu, Xin Hong

"Temperature measurement is very important in metal smelting process. Many devices are used to realize non-contact temperature measurements. Compared to conventional thermocouple, infrared temperature measurement has it's unique advantages. However, using an infrared temperature measurement at the top of the furnace can not obtain the desired optical signal because of disturbance from slag layer, high-temperature gases and other effects. A real time thermometry system with dual-wavelength radiation was presented to get optical signal emitted from molten metal through bottom-blowing nozzle. Taking into account the advantages and disadvantages of bottom-blowing devices, a MHP (Multiple Hole Plug) bottom-blowing device was used, through which the optical signal was transferred to the infrared thermometer by use of optical fiber. After conversion and analysis in real-time, the result was displayed and recorded in computer. After calibration, it could be a good predictor of temperature trend in a metallurgical process. IntroductionAt the refining stage of steelmaking, in order to achieve predetermined chemical composition and temperature, high-temperature molten steel is refined in a furnace such as converter. Because the refining process involved with chemical components and reaction velocities in the furnace rely on the temperature of steel, it is necessary to know the temperature accurately in real time during the process. And temperature measurement is also helpful for the end-point judgment. The temperature in the refining process changes quickly, for instance, in a converter, 300t molten steel is processed in only about half an hour.At present, traditional way of temperature measurement is using a thermocouple probe mounted on a lifter called a sub-lance. The thermocouple is immersed in molten steel and its temperature is measured during the short period until the thermocouple is fused. Accurate and reliable temperature can be obtained by this method, but in consideration of the discontinuous measurement and the costs, missing the end-point temperature may sometimes occur.According to the above background, a method in which a temperature-sensing element such as a thermocouple is immersed directly in molten steel is not suitable for the continuous temperature measurement because materials having such stability are not available. Therefore, radiation thermometry is promising. There have been some reports on radiation thermometry through an observation nozzle through the bottom or side of a refining furnace [1, 2]."

Jan 1, 2014

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

The direct removal of lead ions from D2EHPA-kerosene using metallic zinc as the reducing agent was evaluated. The electrochemical process, called galvanic stripping, is a potential alternative stripping technique when standard chemical methods are not adequate. Four parameters found to be important in the rate of lead removal were studied in a factorially designed experiment. The variable evaluated included D2EHPA concentration, temperature, zinc surface area and solution agitation. Temperature and surface area were found to be the most significant, while agitation and D2EHPA concentration had less influence on the reaction. An activation energy of 22.5 Kcal/mole was calculated indicating a chemically-controlled process. The reaction was also sensitive to the concentration of oxygen in the system. The zinc required was considerably in excess of stoichiometry, possibly due to the dissolution and redeposition of lead: In general, the results were encouraging and demonstrated that lead impurities could be removed from D2EHPA using cementation type reactions.

Jan 1, 1995

By A. M. Strachan

The arising and behavioural pattern of polonium-210 in the Capper Pass & Son Limited non-ferrous metal smelting and refining circuit is briefly discussed. The process developed for the removal of polonium from lead, solder and bismuth is discussed in detail, together with the essential personnel safety and environmental protection precautions which must be taken during the refining and subsequent storage of the active dross.

Jan 1, 1992

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983

By W. Hoffelner

Plasma technology has become increasingly important for the treatment of several types of waste (toxic, nuclear, metal-bearing scrap). Plasma furnaces combine the advantages of a closed hearth process with a very versatile (several plasma gases can be employed) and effective heat source. It can be successfully used for recovery of metals with subsequent purification and/or vitrification of residuals from drosses or filter dusts.

Jan 1, 1994

By G. C. Gullo, H. Wabusseg, P. J. Uggowitzer, H. Kaufmann

"The basic concept of New Rheocasting (NRC) is described and the application of wrought alloys with this process is discussed. Practical experiments with the aluminium alloy AIMgSi I are explained. For this alloy the proper NRC - casting temperature was determined by using Thermo Cale - computer software and DT A and the essential processing conditions are shown. In the experiments the melt was taken from an aluminium holding furnace and cast into NRC steel cups. After controlled cooling the resulting slurries were cast into a 4-step die on an UBE HVSC 350 Squeeze Casting machine. The characteristic microstructural values such as grain size and shape factor were measured and compared with classical casting alloys. The influence of the wall thickness of the step part (6 mm, 10 mm and 14 mm) on the microstructure is described. Tensile properties in different heat treatment states are compared with characteristic prope1ties of the same alloys in forged condition. The ew Rheocasting - process CNRC)The NRC process is a recently developed new semi-solid processing method which allows the production of pore-free, pressure tight components.In the NRC process a fu lly liquid, but only slightly superheated melt is taken from a holding furnace and poured into specially designed steel crucibles, which are placed on a carousel next to the Vertical Squeeze Casting machine. In this ,NULL,slurry maker'· globul ar a-Al grains grow, following forced homogeneous nucleation at the cup wall [ 1, 2]. In the few minutes during which the melt is cooled to sem i-so lid processing temperature, a stable ske leton of a-Al phase forms. The resulting slug keeps a cylindrical shape during its slide into the sleeve of the Vertical Squeeze Casting machine, where it is cast into shape."

Jan 1, 2000

By W. G. Davenport

This chapter shows how flash furnace industrial oxygen and oil requirements are affected by different: (a) product temperatures (b) conductive, convective and radiative heat losses (c) electrical energy inputs (d) hydrocarbon fuels. The calculations of the chapter are all for production of 65% Cu matte from pure CuFeS2 concentrate. Blast temperature is? 298 K throughout.

Jan 1, 2001

By Bhavani Kedika, Venkatagiri Noole, Krishna Thotla, Krishna Reddy Chepyala

Cationic lipids are attractive candidates for transgene delivery and expression and are safer alternatives to viral delivery vehicles. Here, we report the design, synthesis, characterization and transgene expression efficacies of a series of chrysin derived cationic lipids. A series of ten lipids of chrysin was synthesized by treating the 7-hydroxy group with dibromoalkane and further substitution of the bromo derivative with alkyl amines. The synthesized lipids were characterized spectroscopically. Parallel screening of the synthesized lipids for in vitro plasmid delivery expressing luciferase led to identification of several leads that demonstrated higher transgene expression when compared to the standard. Transgene expression efficacy was dependent on the chain length of the lipid. The influence of the various physicochemical properties on transgene expression efficacies was investigated. This study indicates that lipids derived from chrysin results in high levels of transgene expression and may be attractive for gene therapy applications.

Mar 1, 2017

By M. A. Neri

A lead-free solder alloy Sn-57.5Bi-0.5Ag has been developed by mechanical alloying and foundry processes, and has great potential as a lead-free solder system, to low temperature applications. The mechanical alloying powders show a microstructure different to the microstructure obtained by the foundry process for the same alloy. Its melting point of 142°C is slightly higher than that of eutectic tin- bismuth solder. Examination of the microstructure revealed that eutectic microstructure is refined by the mechanical alloying process Ag additions. The lamellar structure of tin-bismuth gradually disappeared with the process of mechanical alloying, while intermetallic compounds AgaSn phase was formed. The Cu-Sn intermetallic compound layer formed at solder-copper interface is the Cu6Sn5 phase. Keywords: Lead-free solder, Microstructure. Mechanical alloying

Jan 1, 2003

By Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"It has been demonstrated that metallic-bearing minerals are physically liberated from host rock when exposed to microwave (MW) energy. The metallic minerals are iron sulfides and spinel oxide minerals contained in peridotite rock. Experimental evidence has shown ore particles readily couple with MW energy at 2.45 GHz, 1000 W resulting in rapid heating. Thermal stresses are generated by highly absorbing metallic-bearing minerals resulting in cracking and embrittlement of ore particles that assists in crushing and grinding processes. The liberated metallic-bearing minerals are shown to report to coarser size fractions as a result of MW exposure.IntroductionComminution of ore material during beneficiation is a large energy expenditure for the mineral processing industry. Crushing and grinding operations alone consume 50-70% amount of energy used in mineral processing [1]. Size reduction becomes increasingly difficult with decreasing particle size making grinding the most energy-intensive step of comminution. The aim of comminution is to maximize liberation of economically valuable minerals from the host rock [2]. Overall, the less material that needs to be handled, then grinded, to create a useful product for hydro/pyro metallurgical processes will achieve the greatest reduction of energy.Much of the scientific interest for use of microwave (MW) energy in mineral processing has been for improved hydro/pyro metallurgical techniques [3-6]. Early authors have employed MW energy for improved grinding of ore particles but most conclude the energy savings do not justify the energy input [7-9]. The effectiveness of MW assisted grinding is dependent on the ore mineralogy and the absorptive properties of minerals contained within it. Ore containing magnetic minerals should prove successful with MW assisted breakage from highly absorptive properties."

Jan 1, 2012

By Sabine Knoll

The thermodynamic properties of four liquid ternary zinc alloys, Au-Sn-Zn, Ag-Sn-Zn, AI-Sn Zn and Cu-In-Zn were measured with an electromotive force (emf) method at three or four cross-sections with an constant X:Sn or Cu-In ratio. At the Au-Sn-Zn and AI-Sn-Zn system calorimetric measurements were also carried out in order to compare the integral enthalpy of mixing from the direct measurements with the data of the emf measurements, which were derived by Gibbs-Duhem integration.

Jan 1, 2003

By M. GONZALES-FERNANDES M

Natural rubber/organophilic clay nanocomposites were prepared and characterized. A brown bentonite from Paraiba’s State, Brazil was modified with a sodium salt and treated with quaternary ammonium salt hexadecyltrimethyl ammonium chloride. The clay in its natural state, after cation exchange with sodium and after organophilization was characterized by XRD, IR, SEM, thermal analysis. Nanocomposite samples were prepared containing 10 resin percent of organophilic clay. The vulcanized samples were analyzed by XRD, SEM. The nanocomposites obtained showed improvement in their mechanical properties in comparison with samples without clay.

Jan 1, 2015

By J. D. Zhu, T. Ohmichi, H. Yasuda, S. Kashiwai, I. Ohnaka

"Since the casting process affects the properties of castings, its computer simulation has been greatly developed in the last decades. This paper presents our recent works, especially on mold filling simulation, because most casting defects such as porosities and inclusions that greatly affect the properties originate during mold filling. The first topic is the mold filling simulation with consideration of cavity pressure change during mold filling, including direct observation of flow phenomena with X-ray and pressure measurement. The second .one is the mold filling simulation in the lost foam process, in which gasification of polystyrene pattern and gas outflow through the coating and mold have been considered. The simulation can predict not only the mold filling sequences but also periodical vibration of the gas layer between the melt and pattern. The third one is the comparison of simulation of Al melt flow in a metallic runner and direct observation through a transparent mold, showing that the entrapped gas or inclusions is expelled ahead through the melt and its simulation needs very fine meshes. These examples show that the comparison of simulation and observation is very important to develop the numerical simulation further.IntroductionThe mechanical properties of castings are greatly affected by casting defects such as porosities and inclusions, and solidification structure. Although recently the structure simulation has greatly progressed [1-4 ], the application in plants is very limited, because the structure is mostly determined by chemical compositions and cooling rate, enabling us to estimate it from the structure of past similar castings without simulation.On the other hand, the casting defects often vary with each casting or time. Among the defects, porosities and inclusions are main causes to deteriorate the properties and mostly originate during mold filling. Therefore, a lot of efforts to simulate the mold filling and estimate those defects have been made in the last decades [l,5,6]. These efforts have been mostly to develop numerical techniques to solve the Navier-Stokes equation. However, the flow phenomena in molds have not been well understood, because the direct observation of the flow phenomena in mold is not easy. This means the accuracy of the simulation is still not clear."

Jan 1, 2000

By Joseph Hamuyuni, Pekka Taskinen

We present experimental results for the liquidus in the system Cu2O - CaO -Al2O3 at 1250 oC. In this study, we quantified the liquidus by the equilibration/quench/analysis technique, with Cu2O, Al2O3, and CaO as primary materials exclusively. Experiments were conducted in air at an at oxygen pressure (p) = 21.3 kPa). Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. We then quantified the liquid chemical compositions by means of Energy-Dispersive X-Ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA). This study reveals inconsistences in liquidus surface of the present ternary diagram of the system here in mentioned. Differences of up to 10 wt % compositions of the species have been observed.

Jan 1, 2015