Search Documents

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By S. Abe

Various copper anodes to be electrorefined were subjected to a heat treatment comprising annealing at a temperature in the range of 700 °c to 1,000 °c followed by a slow cooling preferably on the order of about 150 °c, and using these heat treated anodes , a series of dissolution experiments were conducted under conventional electrorefining conditions. The results obtained have indicated that the above annealing/slow cooling process dramatically improves the dissolution activity regardless of the type of anodes. As an example, passivation times of l to 3 minutes in a standard test have been increased to more than 80 minutes by this innovated heat treatment. Other advantages sterning from the improved anodic activity include reduced electrical short circuiting which results in substantial labor effort in the tankhouse, reduced energy requirement, and reduced cost of processing anode slimes because the amount of anode slimes is reduced. In addition, this process gives rise to a dramatic change in the nature of anode slime layer formed in such a way that a comparable final cathode copper product can be achieved even from high-impurity copper starting material.

Jan 1, 1987

By Vaughan R. Voller

"Over the last ten years an increasing number of heat and mass transfer models of solidification processes have been presented in the literature. A key component in these models is the coupling between thermal and solute fields. This is achieved by developing relationships based on the behavior at the microscopic scale in the casting (typically a secondary dendrite arm space). An important class of models in this respect are models that describe the local scale redistribution of solute alloy components-collectively referred to as microsegregation models. This paper explores this class of models.IntroductionModeling takes a key role in processing materials for properties. This is particularly time in solidification processes where current computer techniques allow for a detailed treatment of the critical macroscopic phenomena. Typically these macro scale models consist ·of three main coupled components.1. A model of flow in the melt and solid + liquid mushy region.2. A model of heat transfer.3. A model of solute transport.The focus of this paper is the solute transport component, in particular the manner in which process scale transport is coupled to transport ·at the local scale of the solid-liquid interface. This step requires a modeling of the redistribution of solutes at the scale of the secondary arm spaces in the dendritic mushy region-a process referred to as microsegregation. Basic microsegregation models use the limit assumptions of no mass diffusion in the solid (Gulliver-Scheil [l]) or complete diffusion in the solid (equilibrium lever rule) in a fixed and space. Recently, however, more sophisticated microsegregation models that account for finite mass diffusion and coarsening of the arm space have been developed [2-19]. In this paper governing equations for a general microsegregation model for a multi-component alloy in a coarsening and spacing _are introduced. From these general equations various models for a binary system are developed and tested"

Jan 1, 2000

By J. A. Holmes

Due to varying and complex mineralogy, the flotation tailings from the Chingola Concentrator have, for some years, contained upwards of 0.4% acid soluble copper. In 1968, an investigation was initiated, to determine a method for recovering this acid soluble copper. This initial investigation concluded with a recommendation to install a leach-solvent extraction-electrowinning plant at Chingola, to treat up to 900 000 tonnes of material per month, for an additional copper production of some 4 500 tonnes per month. The process consists basically of six stages :- Materials reclamation handling and preparation, acid leaching in air agitated pachucas, solid-liquid separation by countercurrent washing in thickeners, solution concentration and purification by solvent extraction, copper recovery by electrowinning, and residue neutralisation and disposal. This paper describes the development of the main parameters for design of each of the six sections, and gives details of the final plant design. Problems encountered in commissioning and initial operations are commented on, particularly insofar as they indicated any errors or misjudgements in the design. The choice of materials of construction is commented on in some detail.

Jan 1, 1976

By P. A. Botha

Most sinter producers prefer to use a range of iron ores with the aim to optimize their sinter blends. ISCOR is however limited to the use of ore from two deposits, namely Sishen and Thabazimbi. Only sinter produced from Sishen ore is described in this report. The Sishen iron ore deposit provides high-grade hematite ore with a mean iron content of 65 per cent. Three major ore types are developed: massive, laminated and conglomeratic. The main ore mineral is hematite with minor to trace amounts of quartz, mica, phosphates and, in places, carbonates. A sinter product is characterized by its mineralogical composition and metallurgical properties. The production rate also plays an important role in the economic evaluation of sinter quality. Sinter-pot tests were conducted with varying basicities, given as the ratio of CaO to SiO:< and coke content. The results of these tests were characterized by mineralogical and metallurgical methods. Basicity of a sinter mix directly influences the mineralogical composition and metallurgical properties. The content of calcium ferrite and calcium silicate increases with increasing basicity, thereby increasing the reducibility and cold strength of the sinter product. Experiments performed during this study provided a model for the optimization of the sinter mix with respect to its mineralogical and metallurgical parameters.

Jan 1, 1991

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly, subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fume less fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By K. Ono

A new process for extraction of titanium metal from its oxide is demonstrated. In this process, row material to be reduced is titanium oxide synthesized from ilmenite. The reducing agent is the Ca+CaCI2 two-phase mixture. TItanium is elaborated in the medium consisted of liquid Ca, Caq and solid TI02 at the temperature range 1200 to l300K by means of mixing mechanically the ingredients in the reactor into a smooth paste. Fluidity of the feed which enables continuous scheme depends on the CaCl2 content. The oxygen level of the reduced titanium is the range 500 to 1000 mass ppm varying with the operational conditions. The Ca+CaCI2 reducing agent is taken out from the electrolysis of CaC12 at 11401(, and this CaCl2 is produced by aqueous chemistry conversion using Cl2 gas recycled from the electrolysis.

Jan 1, 2001

By Hwa-Soo Park, J. K. Yoon, Hoseok Nam

In a thin slab casting process, control of fluid flow in mold is particularly difficult due to the high casting speed and large aspect ratio of the mold and the understanding of the fluid flow motion as well as heat transfer in mold is regarded as the most important information because the melt delivery is directly related to the problems of shell growth nonuniformity, surface turbulence and mold powder entrapment. A mathematical model has been developed for the coupled analysis of fluid flow, heat transfer and solidification in funnel type mold using finite volume method based on a body fitted coordinate and the characteristics of the transport phenomena in the mold of thin slab caster were analyzed by numerical simulation. As a result of simulation, the basic flow pattern is characterized as four large recirculations and two small eddies near the narrow faces of mold, which is somewhat different from that of parallel type mold or other conventional slab caster. The heat transfer model accurately predicted the mold positions susceptible to cracking as a result of thermal stress and the predicted shell thickness shows good agreements with the measured shell thickness on breakout products. We also investigated the influences of some operation parameters such as casting speed, nozzle type, submerging depth and mold material on fluid flow, heat transfer and distribution of solidifying shell and various information for the determination of optimal operating conditions were obtained.

Jan 1, 2000

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By J. Murdoch Mackenzie

Two commercial nickel solvent extraction plants treating laterite leach solutions and using LIX®84-I have been operated in Australia. These circuits employ similar extraction chemistry but differ in their leaching and stripping operations. An alternative process involving elements of both can be conceived. The preparation of the feed solution to solvent extraction plays an important role in nickel extraction using LIX®84-I and the special features of manganese removal and cobalt oxidation in the preparation of the PLS are discussed. This paper compares these three circuit configurations with special reference to the extraction and reductive stripping of cobalt, the transfer of zinc and copper to the strip aqueous, ammonia transfer and sulfur transfer. The potential degradation of the organic and remediation using re-oximation is discussed. Keywords: Nickel, Solvent Extraction, Oxime

Jan 1, 2004

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By Vinay Kumar, Jae-Chun Lee, Abhishek Kumar, Manis Kumar Jha

However, India is rich in ores and mineral, but E-waste recycling is necessary due to the report of national and international studies, which cautioned on the generation, treatment and accumulation of e-waste in India. Current data indicate that the total domestic e-waste generation including imports is around 382979 MT, however waste available for recycling and actually recycled are 144143 MT and 19000 MT, respectively. In which recycling by non-formal and formal sector are 95% and 5%, respectively. On the other hand, India has developed expertise in handling verities of metallic wastes in an organized and safe manner. The development of individual process or combined processes for handling the e-waste is underway. Eco- friendly and energy-saving processes are necessary to comply with stringent environmental regulations. The paper includes the recent trend of e-waste generation, recycling process and its future prospects particularly in India.

Jan 1, 2011

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By James C. Barker

Near Rainbow Mountain in the east-central Alaska Range an ultramafic complex forms a sill-like intrusion composed of dismembered bodies exposed along the south side of the Denali Fault and Broxson Gulch Thrust. The complex comprises dunite and peridotite with lesser gabbro, which together exhibit poorly defined, steeply-dipping compositional layering. The complex hosts four types of copper-nickel occurrences which have characteristic platinum-group elements (PGE), gold, and cobalt distributions. Three of the occurrence-types are considered to have formed as a result of primary mineral segregations which developed during intrusion of the complex. The fourth type of copper-nickel occurrence formed as a result of post-magmatic hydrothermal fluids at intrusive contacts. Scanning electron microscope examination indicates that PGE occur as micron-size telluride and arsenide minerals.

Jan 1, 1987

By Sergio Neves Monteiro, Nuã Simonassi, Helvio Pessanha Guimarães Santafé Jr.

"Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of coir fibers. Both TGA and DTG curves were analyzed to determine the effect of the coir fiber on the thermal resistance of the composites. It was found that the coir fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.IntroductionIn recent years, there has been an increase application of natural fibers as reinforcement of polymer matrix composites in several industrial sectors, with special participation in automobile components [1-3]. Figure 1 illustrates the different components of a modem BMW sedan that are fabricated with lignocellulosic reinforced polymer composites."

Jan 1, 2012

By C. B. Solnordal, R. N. Taylor

"The heat transfer conditions on the outer side of a Sirosmelt lance have been determined using experimental measurements in combination with a mathematical model. By measuring the temperature distribution along the wall of an operating Sirosmelt lance, as well as the thickness of the slag layer on it, it was possible to use the model to determine both the heat transfer coefficient between the vessel contents and the lance, as well as the effective thermal conductivity of the slag layer. The effective thermal conductivity of the slag layer was found to be within the range 0.7-1.3 W.m-1. ºCl, which was in good agreement with measured values for magnetite. The outside heat transfer coefficient varied from 80 to ISO W.m-2. ºC1, which was smaller than quoted in the literature for metal/slag systems. The discrepancy was attributed to the high thermal resistance experienced between the lance wall and the slag layer, as well as the large quantities of combustion gases that envelop the lance tip and reduce convection and conduction from the melt to the lance. INTRODUCTIONThe Sirosmelt submerged combustion smelting process [1] utilizes top injection lances to deliver fuel and air into a metallurgical melt. To help prevent lance failure from attack by liquid slag, helical vane swirlers are used within the annular lance to impart swirl to the flowing air and enhance the heat transfer from the lance wall to the air. The swirlers thus cool the wall, and enable a frozen layer of slag to form on its outer surface. This solid layer ensures liquid slag cannot reach the lance surface, and the lance is protected.A mathematical model of the heat transfer processes associated with the lance has been developed, which combines heat balance equations with engineering correlations to predict the wall and cooling air temperature of the lance, as well as the air pressure distribution. An account of the model was given by Rankin et al. [2]. To further enhance the model and enable it to predict the thickness of slag accumulating on the lance, a detailed analysis of the heat flow through the slag layer commenced in 1992. By far the most complex aspect of the model, the flow of heat from the vessel contents to the outside of the lance was dependent on many factors, including:-"

Jan 1, 1996

By Ximena Massone

Chile is the most important copper producer in the world and the mining sector plays a key value in its economy. However, at present the country does not have a satisfactory set of regulations about closure and restoration of mining operations. In our country many mining operations will, in the near future, shut down their activities, therefore, it is of utmost importance to elaborate and enforce a set of regulations to prevent risks and to protect the environment. The present study is focused on reviewing and analyzing the existing national regulations about the closure of mining operations and preparing a comparative analysis with other international regulations of countries with mining experience. The final results of the study will be a legal proposal to regulate the closure of mining operations in Chile, aiming at minimizing the potential environmental adverse impact, internalizing the social costs by the relevant operators and defining all aspects of liability for the environmental damage.

Jan 1, 1999

By Z. Zhang, R. G. Reddy

The viscosities of industrial lead slags with various compositions were measured as a function of temperature. It was found that viscosities of lead slags decreased with increasing temperature, and the plots of ln(11) vs. 104tr followed a linear relation over the reported ranges of temperature. Using the data of this study and available other related data from the literature, a viscosity expression was developed as a function of composition and temperature. The calculated results using this viscosity expression are in good agreement with the measured data. The composition dependency of viscosity of lead slags is discussed.

Jan 1, 2000

By Z. Sun, H. A. Davies

"Current understanding of the mechanisms by which glassy and crystalline thin ribbons are formed in high speed continuous casting processes is considered. A computer model of the combined heat and momentum transfer during melt spinning has been developed. The influence of roll velocity and of heat transfer coefficient (between the melt and the roll) on the temperature and velocity distributions within the melt puddle is analysed and the thickness of the extracted ribbon computed. The relative importance of heat and momentum transfer under different conditions is assessed and differences between the casting of crystalline and amorphous strip highlighted.IntroductionHigh speed continuous casting of thin metallic ribbon and strip is currently of considerable interest both to metal processers and to those studying process mechanisms. The practical interest arises both from the potential economic benefits to be gained from a shorter and more energy-efficient production route and from the ability to obtain extended and uniform thin strip having a metastable microcrystalline or amorphous structure with enhanced or unique properties. The latter arise from the rapid solidification associated with the cooling of very thin sections of melt brought into intimate thermal contact with one or two rapidly moving heat sinks.The principal processes for casting thin strip include free jet, chill-block melt-spinning (GBMS) (1), melt drag (MD) (2), planar flow casting (PFG) (3) and twin-roll casting (TRG) (4). For the first three of these, all essentially variants of melt-spinning, melt flows through a nozzle onto the circumferential surface of a rapidly rotating roll, whereas for TRG the melt passes into the nip between two contra-rotating rolls. We shall be concerned in this paper with the single-roll melt spinning processes only. For these, a puddle is established where the melt contacts the roll surface and the length of this puddle l is a function of the process conditions, notably the circumferential velocity of the roll Us and the volumetric flow rate of the melt Q. The contact time between any point on the roll surface and this puddle, or residence time eR(= l /Us) determines the thickness of ribbon t extracted from the puddle. This thickness, in turn, partly governs the cooling rate T and the amount of undercooling in the melt and thus the microstructure of the solidified ribbon."

Jan 1, 1986

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005