Search Documents

By David H. Y. Tang

The reinforcement mechanism of suspension effect is analyzed based on beam-column theory. The equations of the maximum bending stress, deflection and transferred bolt load for the bolted roof strata are derived. In the analysis, the bolt load is assumed to be point load and the horizontal stress is uniformly applied to each stratum. The reinforcement mechanism of friction effect is also analyzed. The major function of roof bolting in this case is to create the friction¬al resistance by tensioning the roof bolts, thereby the individual thin strata are "welded" into one single thick stratum. Based on the results, equal spacing of roof bolts is used in the suspension effect while for friction effect, the bolts should be spaced based on equal shear force concept. The design nomographs for the proper bolting pattern and bolt ten¬sion of mechanical roof bolting systems are presented for practical applications.

Jan 1, 1984

Case study data were analyzed to develop and quantify empirical stress transfer relationships between seams for both longwall and room and pillar mines. Layering in the innerburden and the distance between seams were determined to be the controlling factors. To evaluate the effect of bedding planes on stress transfer, laboratory studies were conducted using layered, low modulus gravity loaded photoelastic models. Parameters investigated were thickness, number of discrete layers, modulus and friction between layers. Results showed that there was significant distortion of the pressure bulb in highly laminated conditions which correlated with the results of empirical analysis. Relationships developed were used to modify the results obtained from numerical modelling between multi-seam longwall operations. Research conclusions were demonstrated using case studies.

Jan 1, 1995

By Stephen P. Signer

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to ( I) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

Jan 1, 1997

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Rene Rodriguez

Sandstone paleo-channels encountered during coal mining operation can significantly slow down the advance in mining, and often completely shut-down coal mine production, with consequent extensive economic losses to the mine operator. Definition of the encountered channel usually involves intensive drilling; vertically from the surface and/or horizontally from underground vantage points. Coal operators with limited resources often resort to exploration by extending mine faces toward the channel. Both drilling and underground mining exploration are prohibitively expensive and usually provide only partial information about the location, size and shape of the sandstone channel. A low cost alternative which can also provide a more comprehensive picture of the channel is the application of Underground High Resolution Seismic Methods (UHRSM) developed and successfully tested by GECOH Exploration. UHRSM applies surface seismic reflection technology rotated as needed (usually 90 degrees) to accommodate the faces of the exposed channel, coal rib, or coal in front of the inclusion (sandstone channel, etc.). This entails placing high frequency seismic sources and geophones horizontally across these exposed faces. Refraction and reflection events from the front and back of the channel are isolated, analyzed and inverted, to calculate the channel's location and geometry. This paper presents a summary of the geophysical exploration technique and two case history examples where it was applied. In the first case, the accuracy of the technique was verified through subsequent mining. Mining is yet to commence in the second case. Both cases were applied to room-and-pillar nines where the irregular rib lines significantly extended the data processing effort. This suggests that UHRSM will find the easiest application when used along straight rib lines, but that is not a requisite to the application. The UHRSM should find ready application in longwall mining to delineate sandstone channels and other non-coal inclusions in the middle of the panels or ahead of the gate road faces.

Jan 1, 1994

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Anthony T. Iannachione

The location and time of 2,007 microseismic emissions from a limestone mine in southwestern Pennsylvania were compared with the development of mine faces and the characteristics of the mine layout. Based on analyses of these results, the occurrence of roof failure zones appears to be associated with certain characteristics of the mine plan. It was determined that significant relationships exist between the intensity of the microseismic activity and the scale of the roof failures. Microseismic activity associated with these roof falls occurs in distinct episodes, with the final failure event occurring during approximately a 12-hour period. Each roof fall episode appears to be composed of dozens of distinct roof beam failures. As each beam fails in shear and tension, tens to hundreds of audible noises representing rock fracturing or bedding plane separation can occur. While every roof fall can be viewed as unique, certain mechanistic similarities can be realized through careful observation and monitoring of these complex systems. Understanding these similarities in characteristics allows mine personnel to design the most effective and efficient control technique.

Jan 1, 2001

By Olayemi Akinkugbe

As coal production in the United States continues to increase, the availability of unexploited or virgin fields continue to diminish. As a result, mine operators are forced to mine in unfavorable or multiple seam conditions. The safe, productive exploitation of coal in multiple-scam conditions requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. This paper introduces a new computer program, Lam2D, designed specifically to enhance multiple seam mining operation by quickly and easily calculating, stress, displacement, subsidence, horizontal strain and safety factors associated with multiple seam mining situations. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. Most importantly, the program is greatly simplified by incorporating automatic overburden, interburden, coal and gob property generation thereby reducing typical modeling and solution time to a few minutes.

Jan 1, 2004

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a cannon occurrence in coal mines of the Northern Appalachian Coal Sasin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure togain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and fonation of cutter roof failure. Inmine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dires registered the greatest amount of roof loading near the inter- section of dikes with the rib. Load cells measurim horizontal pressure changes in the roof indicated that the greitest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysts of rock pressure nwnitiring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectfvelv suooort the roof in areas of clastic dikes and prevent cutter roof iailure. However, there lnethads were only successful when employed shortly after mining.

Jan 1, 1984

By Robert R. Thompson

Retreat pillar mining is highly productive but dangerous. The primary danger during pillar removal is premature caving of the roof. Because the safety of the miners is dependent on successfully controlling the roof, the roof must cave in a predictable and dependable manner. Temporary support during retreat is usually obtained by setting posts. They are set manually by a miner working in a dangerous area. A solution to this problem would be a system which could set and retrieve roof supports remotely and safely. The Bureau of nines has developed a remotely operated Mobile Roof Support (PIPS) machine which will place and retrieve temporary roof support. Two PIPS machines were fabricated under a cost-sharing agreement with Southern Utah Fuel Company and mining equipment manufacturer. Each machine carries four 50-ton jacks and is remotely- Controlled by radio. The machines are presently being used by Southern Utah Fuel Company under a long-team cooperative agreement. Not only have there been material and manpower cost savings in not having to set posts, but also the time saved bas resulted in increased productivity. The projected costs of mass-produced machines with tethered remote control rather than radio remote control are estimated at $150,000 each. The radio remote control is more expensive and is considered an optional extra.

Jan 1, 1986

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By Gift Makusha

The Witbank Coalfield in South Africa contains up to five economically viable coal seams. These seams have been mined continuously for over 100 years and the reserve in now becoming depleted. The normal mining method has been bord and pillar with examples of stooping. The situation now occurs where the formed pillars, left to maintain stability, have a higher quality than the coal that is left in the unmined reserves. Where the reserves are less than 70m deep and continuous over several kilometers, opencast mining is being successfully applied. After several years of investigation, Anglo Coal has identified blocks of coal that warrant investigation with regard to pillar extraction by underground methods The proposed method is pillar extraction using Mobile Roof Supports (MRS) It is proposed to mine three panels at a depth of 120m, by keeping the panels narrow and sub-critical. The sub-critical layout does not allow caving to surface and more stress is thrown onto the barrier pillar rather than the face pillars. The sub-critical span is anticipated to be 100m. The paper describes the full geotechnical investigation, including numerical modelling, instrumentation and drawing on the local South African experience of shortwall mining. The project will be unique in that pillars were not designed for pillar extraction and have low factors of safety (l.4 - 1.8) and width to height ratios of less than 4. The mining height will be approximately 4-4 5m, and this represents "new" operating heights for Mining Roof Supports. The required equipment was ordered in late 2002 and pillar extraction is anticipated to begin in June 2003.

Jan 1, 2003

By Eric R. Bauer

Skin failures of roof and rib in underground coal mines continue to be a significant safety hazard for mine workers. Skin failures do not usually involve failure of the support systems but result from rock or coal spalling from between the support elements. For instance in 1997, over 800 miners were injured by roof and rib falls, of which 98 pet were the result of skin failures. Also, nearly 80 pct of the roof and rib failure injuries occurred at or near the working faces in development sections. The face area is a zone where the potential for skin failure accidents and injuries and roof and rib failures, in general, is high because of mining activity, ground readjustment due to changing stress conditions, and the higher exposure of mine workers. In addition, failures occur where the roof and rib are unsupported. This paper features a review of the roof and rib accident statistics resulting from skin failure, highlighting the incidences by average days lost, in-mine location, state, MSHA District, and worker activity at the time of injury. A detailed analysis of recent fatalities caused by skin failure is included. Also discussed are the causes of roof and rib skin failures, current methods and support materials for skin surface control, as well as a historical literature review of skin failures and control methods.

Jan 1, 1999

By Yoshiaki Fujii

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic array. Location of microseismic events and intensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the intensity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increasing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are considered. Observed and predicted displacement of the shaft axis agreed well. Third, is the roadway deformation in Taiheiyo Coal Mine. Attainable maximum stress for a roadway was calculated considering three faults intersecting the roadway. It was realized that the roadway's convergence is related to the calculated stress by simple equations.

Jan 1, 1992

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By Jinsheng Chen

Longwall mining-induced abutment loads on the surrounding coal pillars can be grouped into two categories in terms of the relative position of the coal pillars and the longwall face. They are the front and side abutment loads. Even though a lot of research and efforts have been made to study the nature and behavior of these longwall mining-induced abutment loads, their influence zones and magnitude are still not well defined and fully understood due to the complexity of geological conditions and the longwall muting-induced overburden strata movement. The uncertainty about the mining-induced abutment loads often forces consultants and mining engineers to employ a conservative approach in designing coal pillars and entry roof control plans. The problems with this approach are that: (a) it increases CM development¬longwall retreat footage ratio, (b) it decreases coal recovery, and (c) it increases !Ill' operating costs. However, a more liberal approach may create safety issues and result in loss of production. Therefore, the importance of accurately defining the influence zones and magnitude of the front and side abutment loads induced by longwall mining can never be over emphasized. The authors in this paper attempt to define the influence zones and discuss the magnitude of the longwall mining-induced abutment loads by analyzing the field data measured at RAG American Coal Company's longwall mines. In addition, the relationship between entry stability and the balance among roof/floor conditions, pillar design, and roof control plan is also briefly discussed.

Jan 1, 2002

By Ross Seedsman

Discussion on the design of roof support in tailgates has often been conducted without a clear statement of the stress and failure conditions acting. There is general agreement that in the tailgate the vertical stresses above the chain pillar increase. Within the stress 'bulb' associated with this vertical stress increase there will be an increase in horizontal stress. This does not mean that the horizontal stresses acting across the roof line increase. In retreat longwalling, the proximity of the tailgate to the adjacent goof results in a substantial reduction in the horizontal stress field acting in the immediate roof. Furthermore, at the face/tailgate corner the onset of significant compression of the chain pillar. if it is designed to yield, will result in a further reduction in the horizontal stresses in the immediate roof. It is suggested that this latter mechanism can cause the horizontal stresses in the immediate roof to go to zero. Whatever, the horizontal stress acting across the roof in the face/tailgate corner will be significantly lower than in the face/maingate corner. The implication of the model is that support design in tailgates should be based on the assumption of zero horizontal (in fact tensile) stresses. How the roof behaves in a tensile stress environment is a function of joint spacing and orientation compared to excavation width and direction. It is speculated that the empirical relationship between support density and roof rating results from the relationship between joint spacing and bedding spacing. The onset of stress reductions has major implications to the design of cable and bolt anchorages in the tailgate environment.

Jan 1, 2001

By Claude A. Goode

Large quantities of high grade coal exist in thick seams in the United States. Many of these thick seams are too deep to be surface mined and do not lend themselves readily to underground extraction. To develop the new mining technology required to effectively mine thick seams, the Department of Energy has entered into a Cooperative Agreement with Mid- Continent Resources, Inc. to demonstrate the multilift longwall mining technique in a 28 foot-thick seam at their L.S. Wood No. 3 mine near Redatone, Colorado. The seam will be extracted in two lifts, with a 5-foot natural partition of coal left between the upper and lower lifts. Proper selection of face supports is critical to the success of this project. Specifications were defined for the roof supports, and it was concluded that the supports selected must provide full coverage, yield at the legs, and have a 60-inch push- out cantilever that can be set at any position under full load. A Hemscheidt two-leg shield was judged as the best qualified candidate and was selected for the multi-lift trial.

Jan 1, 1981

By M. Karmis

For several centuries surface subsidence has been recognized as an inevitable consequence of most underground mining. In fact, British court records of disputes and litigations related to property damage due to mining subsidence can be traced to the early fifteenth century (Shadbolt, 1978). The first systematic investigations of the mechanisms involved in mining subsidence can be credited to Belgian Mining Engineers. The re- search effort was initiated after the widespread movements and the resulting structural damages suffered by the City of Liege in the 1920's. The publication of Gonot's 1871 treatise "Loie de la NomZ" (normal theory) was one of the most not- able achievements of the Belgian school of that era (Gonot, 1871). During the past 100 years the phenomenon of mining subsidence has been the subject of intensive research, particularly in Europe where long- wall is the most common method of underground coal mining. Many theories have been advanced to explain the mechanism of ground movement as it develops from the excavation, through the superincumbent strata, to the surface. Such theories include the original concepts of beams, arches, domes and the contemporary mathematical modeling principles of strata movement assuming two extreme concepts-- a continuous elastic medium and a stochastic medium for the superincumbent strata. An excellent review of the development of these theories ?-s given by Shadbolt (Shadbolt, 1978). In conjunction with the theories of mass strata movement in the vicinity of mine workings, the subject of surface subsidence predictions has also been the subject of extensive research. The development of reliable and rational techniques of subsidence prediction is imperative, if this phenomenon is to be recognized and controlled within acceptable environmental levels. Empirical as well as mathematical methods have been proposed to fulfill this objective and a comprehensive analysis of these methods has been presented in the literature (Bramer, 1973; Shad- bolt, 1978; Virginia Polytechnic Institute and State University, 1980). As a result of this intensive research effort, it is now accepted in many )coal fields-- mainly in Europe-- that the state of art in subsidence prediction and control has approached a level where mining induced surface displacements can be predicted to a suggested accuracy of less than + 20 percent. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented. In this country, subsidence is rapidly gaining emphasis as an important environmental problem of underground coal mining. Damage resulting from this phenomenon ranges from land settlement to severe structural damage and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). Yet, the art of subsidence prediction and hence control in this country, for both longwall and room-and-pillar coal mining, is far from approaching the maturity reached by the Europeans. In this paper, field measurments and computer modeling techniques have been used to develop some basic relationships of longwall subsidence and its related parameters. Because the objective of this study was to develop regional subsidence trends, all processed information pertains to the Appalachian coal region.

Jan 1, 1981

By Pengfei Wang, Guorui Feng

"The angle of break is the acute angle created by the coal seam bedding plane and caving line formed by roof strata movement after extraction of a longwall panel. It has a significant influence on stress redistribution both in the gob and abutment. Throughout numerical simulation investigations up to now, little attention has been paid to it, or an angle of break of 90° was used, which, however, is not realistic. This paper presents a detailed numerical modelling incorporating the angle of break against Zhenchengdi Coal Mine. The angle of break was obtained through cross-measure boreholes. Hoek-Brown constitutive model was used to simulate the rock masses. Double-yield constitutive model, which was best fitted by Salamon’s model, was used to simulate the gob. The results show that a “/ \ shape” shear failure zone develops around the gob. The shear failure in the floor along the panel edge is due to opposite shear of rock mass on two sides of the caving line, and the number of yielded zones within the gob floor close to the gob edge is smaller. According to the research, the entry was determined to be driven under the gob edge employing split-level longwall panel layout (SLPL). The other numerical simulation for SLPL shows that stress around the god-side entry is much smaller than pre-mining stress, and the area of intact rock mass at the elevating section is larger than conventional layout. Numerical modelling was then validated by field observation.INTRODUCTIONTo solve low recovery and ground control problems in longwall mining with top coal caving (LTCC) due to large gate pillar or chain pillar, gob-side entry approach is becoming increasingly popular (Nazimko, 1994; Li et al., 2016; Zhao, Wang, and Su, 2017). Gob-side entry is actually a combination of the gateroad, pillar, and gob, which is a typical panel layout with slender pillar or artificial pillar or wall. The abutment load has a profound impact on stability of the gate pillar, as well as the gob-side entry. Better estimates of abutment loading profiles will result in improved evaluations of design of pillar and gob-side entry (Larson and Lavoie, 2016)."

Jan 1, 2018