Search Documents

By Holger Witthaus

The conditions of great mining depth and multi-seam¬longwalling require a special method of rockbolting, It can be described as a control loop which is based on the elements of planning, drivage and measurement. Different planning elements such as the results of the observation of physical models, numerical programmes for calculation of stress-distribution and support success, lab and underground support testing and the knowledge of strata behaviour underground including geotechnical classification are used to get best results. The increasing geotechnical information collected during drivage of roadways are used to estimate and minimise the risks of support-overload. The repeated plan/acutal comparison during the use of roadway and continuously monitoring of support and roadways provided the opportunity of optimising support design during the process of drivage and if necessary in front and after of the longwall face.

Jan 1, 2000

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Quanzhong Gu

Stability of a pre-exnacted recovery room plays a vital role when longwall face approaches and during a longwall face move. In an attempt to extend the application of pumpable cribs into recovery room support and to limit roof bolt installation when a longwall face approaches the recovery room, yieldable and cuttable pumpable cribs (YCPC) were employed in the recovery room at the northern West Virginia mine. The YCPC consists of two layers of materials with different strengths. This allows considerable deformation from the floor and/or roof by sacrificing the soft layer while maintaining relatively high load capacity under mining¬induced front abutment loads. The thickness and stiffness of the soft layer, installation and quality control are the key factors when using the Yieldable and Cuttable Pumpable Crib to stabilize longwall recovery room- Underground observation and monitoring results show that the Yieldable and Cuttable Pumpable Crib is a viable solution to insure stability of the recovery room and can save at least two days for a longwall face move at the mine.

Jan 1, 2004

By D. L. Price

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give hack-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By S. S. Peng

The hydraulic powered supports have been employed in U. S. longwall mining for the past two decades. Yet the sciences of roof control at the powered supported faces remain largely unknown. In order to improve longwall roof control and increase production, a series of questions in longwall roof control should be studied and answered: what is the basic rules of roof behavior in longwall coal faces equipped with the hydraulic powered supports? What is the interaction between the roof, supports, and the floor What is the contact condition of the canopy with the roof, and consequently the load distribution on the canopy? Des the periodic roof weighting really exist in the powered supported face and if so, how does it affect the face area? This paper presents the preliminary analysis of underground observations and instrumentations in a longwall panel with 4-leg shield supports designed to address the questions mentioned above.

Jan 1, 1982

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999

By E. Yasar

This paper describes the use of the sand and plaster physical modelling technique to investigate the deformation around mine roadways using a variety of support methods in a particular form of stress field. The characteristics and conditions of coal measures rock were considered prior to the preparation of the models and the insertion of support The investigation has clearly shown how floor lift, roof failure and sidewall movements of mine roadways in laminated weak rock conditions gradually develops as a result of the increase in the stress and, also, how it is related to the level of support used.

Jan 1, 1995

This paper describes the experiences with the application of the Coal Mining Roof Rating (CMRR) System to South African strata conditions. Roof classification studies using the CMRR system were undertaken as part of a SIMRAC investigation into falls of ground in South Mean collieries. Colliery roof rating exercises were undertaking in a range of geotechnical conditions from shallow level coal seams under flat topography to workings with cover depths of greater than 300m A comparison is made between the CMRR and other Rock Mass Rating systems used to classify different roof geotechnical conditions. The need for geological discontinuity orientation, blasting and rockmass stress adjustments to the CMRR is discussed. The effects of acid mine water on strata weatherability and the need to incorporate immersion tests using acid mine water are also detailed. In addition limited correlation is given between CMRR values and other geotechnical factors such as joint trace length, joint shear strength, joint orientation, weatherability and roof damage due to horizontal stress. Taking cognizance of these observations, a concept of stress induced roof damage triggering is discussed.

Jan 1, 2001

By Yong-Ming Jiang

Longwall mining systems are extremely complex and expensive and require great caution for reliable and efficient operation. In many cases, ground control problems are the primary concern in longwall mining. For example, unexpected threats such as roof falls or shield damage can cause sudden interruption of coal production and safety problems, which can originate from many parameters such as shield capacity, setting load, shield type, conditions of immediate and main roofs, pillar stability, geological anomalies, etc. However, it is difficult to correlate ground-control problems at a longwall face with the related mining and geological factors. In this paper, a method of correlation analysis, called tree classification, which permits the use of a large and variable number of features, is introduced The method provides an effective approach to produce an accurate classifier or uncover a knowledge structure, which will be used to predict future consequences depending on past and current data sets. The application of the tree classification method in longwall stability analysis is discussed, and the major procedures of constructing a knowledge structure are included as an example utilizing monitored leg pressure data in a longwall face. Also, the importance and ranking of the variables related lo longwall shield stability is discussed This is a major step towards developing an artificial intelligence system for real-time interpretation of shield monitoring data and hazard prevention.

Jan 1, 1993

By Andrew J. Hyett

The ISRM commission on testing methods has recently presented Suggested Methods for rock stress determination (Kim & Franklin, 1987). This proposes that even if the magnitude of in situ stress is not sufficient to cause significant ground problems, the optimum shape, orientation, and layout of underground structures can be significantly affected by it. In the design of underground excavations, the engineer often requires a knowledge of the average in situ stress tensor in the rock mass. However, attempts to measure a stress state applicable to design have proved frustrating, and a high degree of uncertainty is introduced by the variability in results. In the belief that deduced fluctuations are random in nature, many separate measurements are often made, so that a more reliable stress tensor average, and some indication of the associated variance (see Dyke et al., 1986) can be calculated. Unfortunately, this approach is limited by economic considerations and, as with any sampling procedure, it is imperative to understand the sources of measured variability, in order to design an optimum measurement programme. Cundall(1987) itemised the main causes of stress variability as a. Instrument and measurement errors, and b. Natural fluctuations of stress from point to point, induced by the action of a boundary stress on the internal rock structure. At least four categories exist: i. inhomogeneous rock, bedding, intrusions etc.; ii. differential contraction, creep, or changes in rock properties with time; iii. proximity to faults or discontinuities; iv. cycles of tectonic activity that cause movement on joints. The latter was successfully investigated using the distinct element programme UDEC. In this paper, the contribution of items (iii) and (iv) (i.e. the items related to discontinuities) to the total stress variability will be discussed, for the kind of rock mass shown in Figure 1. Although many authors have concluded that rock joints have an influence on the stress in their vicinity, a more analytical approach is required if the stress distribution associated with different jointed rock masses is to be (i) compared, and (ii) related to routinely measured joint parameters. If this can be achieved then, prior to any attempt to measure stress in a jointed rock mass, a consideration of joint geometry, joint deformability, and the geological kinematics of joints (e.g. the magnitude and direction of previous movements), can place valuable `common sense' constraints on the expected stress system for minimal extra cost.

Jan 1, 1989

By S. Jayanthu

This paper presents analysis of strata behaviour with special reference to convergence and stress variation during an experimental trial of extraction of pillars with cable bolts as major support system in 6.5 - 8.0 m thick coal seam. Critical span for roof falls was estimated through empirical models and also evaluated by numerical models. In situ strata behaviour studies during 1992-96 for about 70 local/major falls revealed inadequacy of the available literature for interpretation and prediction of the roof falls. Convergence acceleration and variation of induced stress based on continuous monitoring data showed distinct anomalies and potential for better understanding of strata mechanics during pillar extraction.

Jan 1, 1998

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications arc made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a now squat pillar empirical strength relationship.

Jan 1, 1992

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By E. H. R. Schumann

The local stratigraphy and composition of the coal measures, including competent dolerite sill and massive sandstone lavers is shown to have a restricting influence on the development and magnitude of surface subsidence above total extraction panels in South Africa. The critical panel width necessary to induce nonviolent failure of a dolerite sill is quantified. Small subsidence due to the deflection of a 70 metre thick dolerite above subcritical panels is shown by example. Maximum surface subsidence tilt an; ground strain is compared to the NCB model. An exponential subsidence profile curve, SPC, describes a trough half-profile. A parabolic relationship between horizontal displacement and tilt, which has been discovered to exist can be substituted in the first derivative of the SPC in order to generate transverse displacement and strain profiles.

Jan 1, 1988

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By Binchuan Zhang

The combined reinforcement system (CRS) combines the strengths of roof' bolting, resin-anchored cable bolt, and chemical grouting to effectively control the deformation of the strata surrounding an extremely poor entry. It is easy to implement and fast in installation. It is one of the systems that are suitable for the reinforcement and maintenance of extremely poor entries.

Jan 1, 2001

By Wei Wu

A new bench blast design method and its realization with the assistance of the computer is introduced. The basic design principle is to define a rhomb cell, called fully-fractured zone, through a series of full scale bench crater tests and apply this geometric pattern in multi-hole, multi-row blast design. To illustrate the design method, the optimization process and assessment of blast performance are presented in the context of a case study.

Jan 1, 1992

By Michael A. Berdine

In early 1997, Twentymile Coal Company took a dramatic departure from traditional longwall recovery methods. Previously, Twentymile's standard longwall meshing procedure included the use of chain link fencing material. Beginning with the 9-Right to 8-Right longwall recovery operation, Twentymile incorporated a polyester geogrid mesh system supplied by DYWIDAG-Systems International. This paper discusses the subsequent utilization of the polyester geogrid mesh system at Twentymile.

Jan 1, 2001

This paper presents a two-dimensional numerical procedure which incorporates concepts related to the mechanics of strata deformation' as well as' empirical indices associated with subsidence engineering. Regional deformation data were employed in order to establish overburden deformation zones, while material properties were kept constant. Scaling of final displacements was based on empirically predicted values for subsidence and strain for the Appalachian coalfield. The model was validated with a number of regional case studies and predicted subsidence and strain curves were compared to those obtained using the semi-empirical influence function formulation developed by VPI&SU.

Jan 1, 1988

By Brian E. Travis

Recent Developments in the utilization of polymer grid structures for Longwall Shield Recovery operations are discussed. Specifically: various Longwall screen designs and the numerous methods employed during installation. Also discussed is the role of polymer grid structures in head and tailgate mf and rib control and their role in controlling soft bottom often associated in shield recovery operations.

Jan 1, 1993