Search Documents

By Ihsan Berk Tulu

The complex interaction between multiple seam pillar extraction panels and variable topography can generate unexpected ground control problems. This case study describes stress-related damage in multiple seam workings that resulted in difficult operating conditions and compromised the safety of the support crews. The damage appeared to be caused by horizontal stress but the unexpected location of the damage baffled the authors. A 2D Finite element analysis was conducted of the mine layout and surface topography in an attempt to explain the observed failure. It was discovered that the topography resulted in the rotation of the major stress at the location of the current workings. The stress rotation caused asymmetrical interactions between the workings on the different coal beds, which can explain the unexpected response observed in the mine. Consequently the layout of the next panel was changed by locating the vulnerable entry 30 ft away from its originally planned position. The new location was selected to locate the entry in favorable stress conditions. The change in layout resulted in a significant improvement in conditions when the next panel was mined. At the time of writing this paper, a full panel has been developed using the modified layout without undue ground control problems. The case study demonstrates that numerical models can help engineers to interpret and solve complex multi-seam interaction problems.

Jan 1, 2014

By Peter Griesenbrock

In German underground coal mining mostly arch and some rectangular roadways are used in the development work. Due to its positive results from numerical and physical modeling techniques as well as good underground experiences, the numbers of rectangular roadways has increased significantly. Today the bolt support - independent of its cross-sectional shape - represents an undeniable support element. During the introduction of new bolt techniques a detailed investigation of the rock and support mechanical effectiveness of bolt support in roadways at all operation stages is of basic importance. This effectiveness can be predicted and verified using different simulation techniques. For the planning of rockbolted roadways two supplementary simulation techniques are presented in this paper. By combination of all available planning tools the best result for planning assurance can be achieved. Keywords: numerical modeling, physical modeling, arched roadway, rectangular roadway, roofbolting, advancing longwall.

Jan 1, 2002

By Andre Zingano

It is known that the backfilling confinement increases the pillar strength and also reduces the rib lateral displacement. With backfilling, it is possible to increase the room-and-pillar mining recovery. This paper aims to study the behavior of coal pillars confinement using rock fill as backfilling material. Laboratory tests were carried out to determine the behavior of backfilling materials. Constitutive models were developed for the tested backfilling materials. Numerical simulations for the effect of backfilling materials on the ground stability in room-and-pillar coal mine entry were performed. The backfill method is a good strategy to (i) improve the ground stability in room-and-pillar coal mines for long term, especially for weak coal seams, (ii) increase the coal mining recovery and (iii) reduce the quantity of waste material on waste piles at the surface.

Jan 1, 2011

By Syd Peng

In designing a proper roof support system, one must know the features of roof geology in advance of mining. The drilling parameters obtained during normal roof bolt installation cycle can provide a large amount of information on the roof geology when properly interpreted. It is also an economic way for identifying the geological features of the roof. This research develops a method for predicting the roof geology based on the drilling parameters obtained during roof bolting operation. From the results of a series of laboratory and underground tests, feed pressure is found to be a good indicator for identifying the voids/fractures and estimating the roof rock strength. This paper describes the method for determining quantitatively the location and the size of void/fracture and estimating the roof rock strength from the drilling parameters of roof bolter.

Jan 1, 2005

By Stephen C. Tadolini

Cable supports offer several advantages over traditional secondary support methods. Cable supports enhance stress redistribution to pillars and gob areas, minimize or eliminate timbers and cribs which reduce ventilation capabilities, eradicate material handling injuries related to the placement of crib supports, and provide a cost-effective alternative to secondary support. The U.S. Bureau of Mines has designed and installed cable supports to improve the stability of tailgate entries in an underground western coal mine. Two entries closest to the Iongwall panel were solely supported with high-strength cables installed with cement grout. Basically, with modifications in the intersections, 360 ft of roadway nearest the longwall panel was supported with two rows of 22-ft-long cables installed on a 7-ft spacing. Approximately 250 ft of a second bleeder entry was supported with two rows of 16-ft¬long cables installed on a 7-ft spacing. Individual cable loads were monitored with hydraulic U-cells and pressure pads. The roof behavior was simultaneously monitored with differential magnetic sag stations and closure meters on 25-ft spacing during longwall panel retreat to evaluate the response of the immediate and main roofs. Cable supported gateroads appear to be a viable alternative in secondary support when compared to wood timbers and cribs. This paper describes the theory, application, and advantages of cable supports and presents the results of the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1993

By Tom Blevins, Roland Walker, Jinsheng Chen

"The Dywidag-Systems International DSI Tandem Anchor bolt, with an improved expansion shell-washer design, can substantially reduce potential entry roof falls caused by twisted or deformed expansion shells of the traditional mechanical anchor bolts during installation. In addition, the improved anchorage system can also ensure that a consistent and high installed load is achieved, which is critical for effective beam building under thinly laminated or layered roof conditions. This paper discusses the genesis and anchorage performance of the Tandem Anchor bolt, and analyzes the tension/torque relationship of different mechanical shell anchors using data obtained from both lab and field tests. It also discusses roof bolting mechanisms, roof bolting systems, and factors influencing effective beam building. Finally, numerical modeling was used to analyze the effect of bolt pretension magnitude on entry roof stability.INTRODUCTIONThroughout the history of underground mining, keeping the roof from uncontrollable collapse has been the greatest concern of the miner. Tremendous strides have been made in better understanding, predicting, and supporting the mine roof. This conference has spent the last twenty-eight years sharing information and distributing it to the mining community. A paraphrased statement from former Secretary of Defense Donald Rumsfeld adequately describes the challenges to the mining engineer as it pertains to roof control: it is a study of known knowns, known unknowns, and unknown unknowns. It is the hope of the authors to address some of these unknowns.The paper discusses the development of bolt anchorage systems from dry shells to shells with resin-assisted anchorage. It looks at some of the issues faced with the anchorage shells being used when introducing the insertion pressures caused by resin cartridges. The rationale behind the shell design changes was to compensate for this resin induced stresses.An improved expansion shell assembly (a slotted expansion shell base, a tapered cramming plug, and a novel support nut with tapered top) for mine roof bolts makes up the Tandem Anchor (U.S. Pat. No. 6742966); this minimizes the possibility of twisting seen with traditional mechanical shells and thus prevents springy bolts and shell leaves from breaking. A fully grouted Tandem Anchor bolting system has the advantages of both the pure mechanical point-anchor and the non-pretention fully grouted bolting systems. Once installed, the installed load or pretension will be locked in and never bleed off. Compared with the fully-grouted (2-speed resin) tension rebar bolting system, the fully-grouted Tandem Anchor bolting system can (a) reduce bolting cycle time (about 15 seconds per bolt), boosting coal production and productivity; (b) provide a greater installed load or pretention; and (c) achieve a consistent tension/torque ratio, which gives better bolting quality control. Therefore, a fully grouted Tandem Anchor bolting system is the most effective means to reinforce a weak rock mass intrinsically by the theory of beam building. For thinly laminated or layered roof conditions, a higher installed load or pretention (50% or more of the bolt's yield strength) can make a roof bolting system much stiffer, which results in less roof movement. Numerical modeling results show that the magnitude of the roof's tensile stress and relaxation zone can be substantially reduced under a higher installed load or pretention."

Jan 1, 2010

By N. C. Saxena

Subsidence investigations in Indian coalfields have led to development of relationships between subsidence movement parameters and defining of safe limits of subsidence movements for surface properties. The maximum subsidence over caved workings was generally not more than 60% of extraction thickness underground while in case of hydraulically sand stowed workings it was generally not more than 5%. The relationships have been useful in extraction of more than 7-million tonne of coal from underneath and in the vicinity of surface properties.

Jan 1, 1988

By David Bigby

Room and pillar mining with full pillar extraction is one of the most hazardous systems of underground coal mining, a significant hazard being the potential for sudden goaf override. The Autowarning Telltale (AWTT) is a new development for pillar extraction operations, based on the well proven and simple Rockbolting Telltale safety monitoring device. It is now being applied in room and pillar coal mines in India, with significant potential for application worldwide. The Autowarning Telltale is an intrinsically safe low-cost, self-contained unit installed into the roof either during pillar development or prior to pillar extraction. It provides a highly visible warning via flashing Light Emitting Diodes (LEDs) when a preset level of roof movement has been exceeded. The paper provides a full description of the instrument and two case histories of its initial application at fully-mechanized Indian sites using the split and fender technique.

Jan 1, 2011

By Michael Gauna

Ground fall injuries and fatalities in United States underground coal mines have shown a diminishing trend. Advances in bolting and standing support systems have led to improved safety in underground coal mines. However, the Crandall Canyon Mine disaster in 2007, in which 9 individuals were fatally injured as a result of a widespread collapse, emphasized that proper mine design is a critical issue that must be addressed. The Mine Safety and Health Administration (MSHA) has instituted technical review procedures structured to facilitate the implementation of safe mine designs in underground coal mines. The technical review process and the typical information required are outlined in this paper. The range of mining situations that lead to a technical review, common design methods submitted for review, and their relevant guidelines and limitations are also discussed. Additionally, the relationship between design criteria and mine site historical experience is discussed.

Jan 1, 2011

By Q. F. Wang

Spontaneous combustion hazard of loose coal in the top-coal caving region of entry affects the safety of the entry and top- caving longwall face seriously. In this paper, by combining on- site temperature tests with lab tests and numerical simulation, the characteristics of microcirculation close to the top-coal caving region are analyzed. A model for the temperature fields of the microcirculation in loose coal is presented. Based on this model, the temperature distribution and possible self-ignition region can be predicted. Further, the heat and mass transfers in microcirculation are studied. Finally, the mechanism of oxygenation during the spontaneous combustion of microcirculation in loose coal of the top-coal caving region of entries is put forward. The research results in this papa may provide ideas for the prevention and putting out of the fire caused by spontaneous combustion in the caving zone.

Jan 1, 2004

By A. W. Khair

This paper presents an analysis of ground movements recorded from longwall operations in the Northern Appalachian region in West Virginia. The site chosen for the investigation was selected due to varying heights of overburden and topography and was instrumented for both surface and subsurface measurements. The instrumentation areas consisted of two panels covering various sections with unique geologic and topographic features. Instrumentation included surveying monuments and shallow boreholes using an inclinometer for measuring horizontal strata displacements. Vertical strata deformation was monitored utilizing a unique design of the mechanical grouting method. Full length borehole profile extension was measured using Sondex displacement rings in the inclinometer installation. Subsurface displacements, i. e. caving zone, fractured zone, and highly deformed non-fractured zone were identified. The nature of surface disturbances with respect to varying geologic settings were compared, and an attempt was made to simulate final strata caving and bed separation using finite element analysis.

Jan 1, 1987

By S. J. Mitchell

An analysis of bolting reinforcement of several large [approximately 18 m (60 ft) cube] pillars was performed. The many overcoring stress profiles in pillars at the mine were used to produce generalized stress distributions at various stages in pre- and post-failure. A complete stress-deformation curve was estimated from this data. The effect of pillar bolting on the load-deformation behavior was extrapolated from the observed unbolted behavior. Bolting can increase pillar strength by up to 10 percent. The effect of bolting on general mine stability was examined with a shoW computer analysis. The computer model was calibrated against measurements performed at the mine, and produced good agreement between measured and modeled stresses. The analysis indicated that bolting increases the bolted pillar safety factors in the event of additional pillar failure by a small amount (approximately 5 percent). Progressive pillar failure is unlikely, because arching transfers most load from yielding pillars to large unmined abutments rather than to the smaller panel pillars.

Jan 1, 1984

By Khaled Morsy

In this paper a new method to evaluate the stability of yield pillars was introduced. The evaluation of yield pillar stability was conducted in three steps: (1) Estimation of pillar loading - numerical modeling is a good tool to estimate the pillar loading for most of the geological, geometrical and mining conditions. In this study. finite element technique was used to estimate the state of stress, strain, elastic strain energy and plastic energy, etc. at every point within the pillar. (2) Defining the yield pillar loading zones¬. The proposed method considered the non-uniform stress distribution of yield pillars by dividing the area of the yield pillar into three loading zones, namely core, transition and rib zones. (3) Estimation of stability indicators - an appropriate stability measure was proposed for each loading zone. such as; Core Stability Factor. CSF, Pillar Bump Index, PBI and Rib Instability Index. RIF. A case study of successful and unsuccessful yield pillar application was used to assess the applicability of the proposed method.

Jan 1, 2003

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By D. W. H. Su

This paper presents the results of ill situ horizontal stress measurements using a Minifrac system in several northern Appalachian coal mines. The effect of stress magnitude and orientation on longwall gate entry stability was analyzed using a series of three-dimensional finite element analyses. The best headgate stability is achieved if the maximum horizontal stress is aligned with the direction of longwall retreat or if the panel is oriented such that the maximum stress relaxes over the headgate due to the presence of the newly formed gob. The degree of horizontal stress damage to longwall gate entries depends largely on the stress magnitude and roof geology. Accurate assessments of support or design techniques which may mitigate longwall headgate or tailgate instability in areas of thinly laminated roof and high horizontal stresses must account for the in situ horizontal stress state and site specific roof geology. The ability to measure stresses and map geology is thus essential to prevent ground control failures at the longwall headgate.

Jan 1, 1995

By Daniel W. H. Su

Underground roof geology reconnaissance is being conducted by CONSOL Inc. to enhance mine productivity. Often, roof instability within mine entries is the consequence of highly variable geology that cannot always be detected from information provided by widely-spaced surface core holes. Utilizing a combination of roof drilling data, geophysical logs, and borehole camera and fiberscope observations, roof geology mapping is conducted within longwall development entries in areas of specific concern prior to commencement of longwall mining, Depending on the uniformity of the site-specific roof geology, data point spacing along the longwall development generally ranges from one to five crosscuts. Surface core hole data are correlated with the roof geology mapped underground to validate the underground observations. Detailed roof geology maps can then be produced to enable ground control engineers and mine management to select cost-effective ground control techniques. However, this procedure is not necessary or useful in all situations and it is employed only when there is strong geologic evidence to justify a closer inspection.

Jan 1, 1999

By Khamis Y. Haramy

The U.S. Bureau of Mines installed surface and subsurface instruments at a mine site in Colorado to monitor and characterize the overburden response to longwall mining. Instrumentation included a time-domain reflectometry (TDR) cable, a multiple-point borehole extensometer (MPBX), vertical-deformation surface monuments, and in-mine pressure cells for monitoring abutment, pillar, and gob loads with respect to the longwall face position. The purpose of the study was to collect data that could be analyzed to correlate the design of the mine layout to the resulting overburden failure response. Determining the extent of caving and fracturing is important in the arid and semiarid Western United States because of the possible consequences to the fragile underground hydrologic systems upon which the land owners and users depend. This study is unique from past investigations because the overburden contains massive sandstone members that impose special conditions on the caving process and pressure redistribution above the longwall panels. This paper presents the results of this correlation study.

Jan 1, 1992

Previously, a variety of risk rating systems were used on different mines. However, these were mostly site specific and geology based systems. The purpose of developing a uniform rating system, to be used on all Anglo Coal open cast mines, is to provide an unbiased, standard and quantifiable assessment of the risk from highwall and lowwall failures. This takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and other parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all open cast mines in Anglo Coal use an almost identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. The implementation of this new system (a computer program that automatically calculates the risk) has been made as practical and easy to use as possible. Therefore, this tool can be used by personnel from other mining disciplines not directly related to rock engineering.

Jan 1, 2004

By Yongping Wu

The steeply dipping coal seams in this paper refer to those with the angle of inclination ranging from 35° to 55°. The reserves of the steep coal seams account for approximately 15%~20% of the total coal reserves in China. In the past 12 years, the top-coal caving mining method had been used to mine the steeply dipping thick (11.5-16.4 ft or 3.5-5.0m) coal seams. However, the mining process of top coal caving is complex with low recovery rate and nearly 30% of coal was wasted. Those problems can be solved by using the single pass large mining height (11.5-16.4 ft or 3.5-5.0m) method. But the movement of the overlying strata around the mining face area of large mining height is complex and it is hard to control the stability of ?rock-shield support? system. Therefore, field measurement, numerical simulation and physical (similarity material) simulation methods were used simultaneously to analyze the strata movement, roof structure and rock-shield support interaction characteristics. The results indicate that strata movement, which is the same as mining the steeply dipping seams with conventional mining heights, is asymmetrical about the dipping direction of the face; deformation, failures, and movement of the surrounding rocks are more intense; the roof weighting interval decreases; the weighting intensity increases significantly; and face sloughage occurs frequently. In the gob, the space for sliding and rolling of the roof increases; the broken main roof tends to form an anti-dip pile structure; the backfilling and compactness of broken roof increase at the lower portion of the face, thereby inducing significant unbalance in stress distribution between the upper and lower portions of the face. The overlying strata above the face form a multi-level step structure. The characteristics of contact and loading of roof-shield support system are more complex. The range of shield load variation is larger, and interaction between shield supports occurs frequently. Anti-toppling and anti-sliding devices at the face become more difficult to implement. The research results provide a theoretical basis for the mining practices in the steeply dipping thick seams with a large mining height. The practice in panel 25221 of 2130 coal mine indicates that the accident rates have been greatly reduced and good technical and economic benefits have bee realized.

Jan 1, 2014