Search Documents

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By R. K. Mehta

Conventional triboelectrification based dry coal beneficiation methods require ground coal as a prerequisite feed material, energy intensive static-in-line mixer or cyclonic tribocharger configuration, and transport and/or improvement in the design of free-fall separators to improve the separation efficiency of [me pyrite/mineral matter from coal. The proposed paper illustrates the two concepts. First, the use of ceramic media in a polyurethane lined attitor in achieving simultaneous grinding and differential charging. Second, the use of an electrocentrifuge to selectively separate coal from mineral matter present in the triboelectrified mixture. It is of interest to note that some ceramic media can satisfy the requirements of both desired density and work function to achieve grinding and differential charging.

Jan 1, 1996

By Paul Soros

There has been a steady increase in shiploading capacities in the last 20 years. One of the reasons has been the general increase in ship sizes, with the largest vessels currently around 280,000 DWT in the bulk trades. Obviously, the large vessels can accept loads faster and their economic utilization justifies higher loading rates, up to a point. The high capacity facilities have loading rates far beyond this point. The economic logic of these facilities is based on the fact that for a given annual throughput the capital and operating cost of a single high capacity system is less than that of two smaller systems. Thus, where the projected throughputs are large, there is a great incentive to reduce capital costs by maximizing capacity. Tubarao, in Brazil, designed for a 100 million ton per year throughput with one finger pier and one high capacity berth is a successful demonstration of this approach. In the current state of the art, the high capacity systems have shiploading capacities in the range of 10,000 - 16,000 TPH, for annual throughputs of 20 million tons and larger per loading berth.

Jan 1, 1982

By Abb Raymond

Finely processed industrial minerals in "powdered" form have long been utilized by the plastics, paint, rubber, paper, ceramics, and adhesives industries as fillers, extenders, coatings and special additives. These minerals, primarily calcium carbonate, talc, kaolin, titanium dioxide, and the like, have provided economic, uniform and consistent base materials which have, in turn, been used by the referenced industries to manufacture quality products. The focus of this paper will be the development of equipment and systems at ABB Raymond for the dry processing of such non-metallic minerals in order to meet what have become increasingly stringent requirements of the producers of these minerals. Changes in these requirements seem to have been accelerating rapidly during the last ten years, and it is expected this process will continue into the 1990's.

Jan 1, 1990

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By R. M. Quinlan

The coal industry in the United States has undergone significant economic changes during the past six years. The price of coal remained relatively constant from 1950 to 1969 (See Figures 1 and 2). Steam coal prices tripled and metallurgical coal prices doubled from 1969 to 1974. This price structure has created a new economic environment for coal preparation. Contributing factors to these price trends include: ? Coal Mine Health and Safety Act of 1969 ? Mid-East oil embargo of 1973 ? United Mine Workers of America contract agreements ? Productivity decrease (tons per man-day basis) ? Environmental Protection Agency regulations The increased value of coal justifies additional capital investment in cleaning facilities to optimize yield. Current trends include recovery of existing slurry ponds and recleaning of refuse. Coal preparation plant product yield and quality must be evaluated in terms of the amount of capital expended and cost of operation. Therefore, it is advantageous to optimize the plant product based on clean coal selling price and rate of return on investment.

Jan 1, 1976

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By J. C. Purcupile

In this time of increased coal demand, a faster and safer method for roof support is needed. This report outlines the preparation and testing of a machine which we feel will help answer this need. The results of the tests are encouraging, and indicate that further exploration of the method should be continued.

Jan 1, 1975

By Dennis C. Parker

The Porters Creek clay is mined for its absorbent properties. The formation is part of the Upper Mississippi embayment and is recognized in Alabama, Mississippi, Tennessee, Kentucky, Illinois, and southeast Missouri. Major minerals in order of abundance are Montmorillonite, Quartz, Illite, Kaolinite, and Chlorite. Mining consists of open pit operation utilizing track loaders or scraper. The clay is dried or hardened in rotary kilns and crushed to size by roll crushers. The clay granules are sized and air classified prior to storage for shipment or packaging. Granules are sold for pet absorbents, oil absorbents, anti-skid material, fertilizer, and pesticide carriers.

Jan 1, 1979

By C. A. Rowland

Comminution efficiency can be expressed in three different ways. Theoretical Efficiency: actual energy consumed, in a comminution machine compared to the theoretical energy required to make the size reduction. Operating Efficiency: compares the operating work index, calculated from production comminution machinery operating data, to the Bond Work Index from bench scale comminution tests or calculated from pilot plant operating data. Economic Efficiency: income compared to planned income. Using the Bond Work Index and operating work index, this paper explains how to determine operating efficiency.

Jan 1, 1998

By D. E. Larson

The U.S. Bureau of Mines has developed a image analysis methodology to correlate the energy consumed during the grinding of an ore to the mineral liberation achieved. Energy consumption values are obtained using a laboratory-scale ball mill equipped with a torque sensor, and an automated image analyzer is used to determine the liberation present in ground products. By combining liberation information with energy consumption data an appraisal can be made of the energy required to liberate the mineral(s) of interest. Results of tests performed on a complex sulfide material determined the effects of grind duration on the liberation achieved and the energy efficiency.

Jan 1, 1995

By H. Hinds

Plant testing of DuPont's Activator Technology in the vat leach circuit of the Homestake mine shows increased gold recoveries of 3-5%. Activators are catalysts of gold dissolution in cyanide solution. DuPont received the patent for this technology in January, 1996. The test was run in the west sand plant alternating control and activated vats to reduce the variability in head grade and cyanide consumption. Activated vats had gold in the preg solutions earlier, higher gold recovery, and lower gold residuals. Activator addition did not adversely affect mill operations or the environment. Optimization of the technology continues.

Jan 1, 1997

By T. F. Tomb

on' January 6, ,1992, the Mine Safety and Health Administration (MSHA) issued an Advanced Notice of Proposed Rule Making (ANPRM) for diesel particulate (DP). The ANPRM identified five areas where the Agency was seeking additional information to assist in the rule making process. These areas were exposure 'limits, risk assessment, consideration of other information, sampling and monitoring methods, and feasibility. The period for submitting information relative to the ANPRM closed July 10, 1992. Prior to issuance of the ANPRM, the agency was involved in conducting studies to evaluate sampling and control technologies and to gather information with respect to occupational exposures to diesel particulate in underground mining operations employing diesel-powered equipment. Since issuance of the notice, additional studies have been conducted to provide supplementary information in these specific areas. Results of these additional studies indicate that average DP levels in coal mines not using aftertreatment range from 0.9 to 2.1 mg/m3. Aftertreatment devices can reduce these levels by approximately 50 to 90 percent. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1994

By D. W. Park

Longwall Strata Control and Maintenance System (LoSCoMS) is a software and data communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels including excessive shield load, low setting pressure, leg leakage and poor shield performance, eminent maintenance problems, etc. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems of their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 1998

By A. C. Alexander

Chevron Resources Company owns and operates an open pit phosphate mine and mill 11 miles north of Vernal, Utah. The plant currently produces 500,000 tons per year of concentrate and has the capacity to produce 750,000 tons per year. The operation is currently being expanded to 1,300,000 tons per year of concen¬trate in order to supply a new fertilizer plant being constructed by Chevron Chemical Company in Rock Springs, Wyoming. A 10-inch, 96-mile pipeline is being built to transport the concentrate from Vernal to Rock Springs. The present and expanded operation will be discussed. HISTORY In 1915, Harry Ratliffe staked nearly 15,000 acres of low to medium grade phosphate rock along the southern flank of the Uintah Mountains. This deposit became the largest privately owned phosphate deposit containing approximately 700 million tons of reserves. Initial development of the deposit began in 1958 by San Francisco Chemical, a joint venture between Stauffer Chemical Company and Mountain Copper Limited. In 1968, Stauffer Chemical Company bought out Mountain Copper Limited and became sole owner and operator. In 1981, Chevron Resources Company bought the property from Stauffer and has operated the mining and milling operations since.

Jan 1, 1985

By Marcus M. Key

Silicosis among metal miners is an ancient disease, probably as old as mining itself.' However, the primitive forms of mining were not productive of much silica dust, and the short life span of slaves used in mining probably precluded the development of more than a few sporadic cases of silicosis. Early diagnostic terms of miners' asthma and miners' phthisis suggested an occupational relationship and a tubercular component, but little attention was given to silicbsis until the turn of this century when epidemics of silico-tuberculosis arose due to the great expansion of the mining industry in the United States, especially silver and gold mining. The expansion was accompanied by mechanization and the introduction of pneumatic tools, which generated increasing amounts of fine silica dust. Mining communities were crowded and hygiene was poor.' The tubercle bacillus would probably have flourished even without the predisposition of silicosis.' As is so often the case in occupational health, biostatistical analyses first called attention to the problem, and environmental-medical studies later confirmed its existence. The bio-statistical analyses were occupational mortality statistics compiled by the Prudential Life Insurance Company in 1907, showing evidence of excessive mortality from tuberculosis and relationship to dust exposure. I The

Jan 1, 1971

By S. K. M. Chao

The increasing demand for large volumes of relatively low-cost cement has resulted in the need for an equally low-cost high-volume means for transporting that cement. It has been estimated that 20% - 25% of the total cost of cement to the buyer represents delivery expenses from the mills. For instance, during the 1972 cement shortage in the Southeastern region of the U. S., bid prices for a ton of cement delivered increased to $45 compared to $20 average at mill price, i. e. , F. O. B. plant. Much of the increase was caused by the anticipated higher cement shipping costs for longer hauling distance. The exceptionally high bid price, of course, was not the price quoted by the successful bidder. Thus, clearly, cement is not a marketable commodity unless it can be economically transported to the consumer.

Jan 1, 1975

By Edgar O. McAlister

Associated with cordilleran intrusives of intemediate to acidic composition, gold/silver ores are generally found in the intruded host rocks which are adjacent to these intrusives. Generally precious metal deposits lie further from the intrusives than allied base metal deposits. For vented intrusives, the associated volcanics may constitute the intruded rock and form the host for precious metal accumulation. Potential field methods, particularly magnetics, can help to define unseen boundaries of intrusive systems and thus can point to generalized prospecting targets. Other clues arise from the intrusive system type, its emplacement fracturing, the host rock type and local magnetic changes caused by mineralization processes.

Jan 1, 1984