Search Documents

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By JESSICA W. A. AZURE, Kansake A. Bruno, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

Blasting generates undesirable ground vibration with adverse effects on humans, the environment, and structures. Numerous studies have used various techniques including machine learning (ML) to predict the peak particle velocity (PPV) caused by blasting in surface mines. These studies used the validation-set approach to evaluate the performance of their predictive models. In this study, Random Forest (RF), Gaussian Process (GP), and Gradient Boosting Machine (GBM) were applied for the prediction of PPV using data from a large open-pit gold mine in Ghana. An ensemble model based on a stacked generalization approach was then built on these three base models to significantly improve the PPV prediction performance. The model evaluation was done using repeated tenfold cross-validation which resolves the challenges with the validationset approach for small datasets. The dataset used in this study comprised a total of 196 measurements taken from different blasting operations. R-squared ( R2 ), mean absolute error (MAE), and root mean square error (RMSE) were used to evaluate the model performance. The results obtained from these models revealed that all the base models did not significantly outperform each other. However, the stacked generalization approach had a better performance, with RMSE = 0.12, R2 = 0.96, and MAE = 0.07. This approach presented an improvement over the existing methods and will be useful for highly accurate predictions of ground vibration during blast design. The application of this model will be useful for efficient and effective blast design.

Nov 8, 2022

By S. Saeb, C. Francke

Introduction Although mining in one form or another has existed for millennia, the use of numerical methods for mine design is a relatively recent development. The basic physics that control the behavior of rock or soil have been known for centuries, but it wasn’t until the last half of the twentieth century that analytical methods that could accurately predict the behavior of a large, irregular rock mass were developed. Before the advent of modern computers combined with differential and integral analytical methods, numerical methods available to mining engineers were limited to closed form solutions for simple excavation geometries. Today, mine-scale three-dimensional stress analyses can be performed on a relatively inexpensive personal computer. Many of the recent advances in rock mechanics modeling are the result of research funded as part of nuclear waste repositories around the world. The large scale exacting performance requirements of waste repositories are frequently very different from traditional rock mechanics projects. These facilities are designed and built under tighter control and scrutiny because of the potential hazards they present to the public. Therefore, a great deal of research towards advancing rock mechanics and numerical modeling resulted from these projects. Much of the repository research is applicable to commercial mines. The advances in modeling programs have been paralleled by advances in computer equipment. Today, a moderately equipped personal computer can handle most mine geomechanical modeling projects in a reasonable period of time. While the learning curve varies, an engineer with modeling experience can develop a medium sized model in a few days. The relatively low investment cost of geomechanical modeling today makes it accessible to most mining operations. The benefits of a solid geomechanical modeling program include reduced operating costs, improved safety, and reduced design costs.

Jan 1, 2007

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Carmen Scalise, Miquel Sanchez

"The McCook Main Tunnel system consists of a 10-m (33-ft) finished diameter, 490-m (1,600-ft) long, hard rock tunnel constructed from a 27.5-m (90- ft) diameter and 92-m (300-ft) deep main gate and tunnel construction access shaft. The gate shaft houses six, high-head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steellined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir.The construction of the tunnel system has been divided into two contracts. The gate and construction access shaft was completed in August 2011. The tunnel excavation and concrete and steel lining was completed in September 2014. The remaining and undergoing construction include the tunnel connections to the reservoir and the Mainstream Tunnel and installation of gates and hydraulic cylinders. This article focuses on the live connection of the McCook Main Tunnel to the Mainstream Tunnel that was initiated in November 2014 and will continue through the seasonal drier weather conditions in Chicago approximately from October through April. Chicago TARP systemThe MWRD has been addressing combined sewer overflows (CSO) and flooding in Chicagoland since the late 1960s and formally adopted the tunnel and reservoir plan in 1972 to protect the region’s most precious drinking water supply, Lake Michigan. Phase I of TARP, which included construction of 175 km (109 miles) of deep storage and conveyance tunnels with diameters up to 10 m (33 ft), was completed in 2006. In addition to protection of Lake Michigan from CSO discharges, Phase I resulted in substantial improvements in surface water quality as well as the quality of life for lake and riverfront communities in Chicago. Water quality improvements and flooding mitigation will be further enhanced as Phase II reservoirs are placed in service, including the three large reservoir systems, McCook, Thornton and Majewski (Fig. 1).The McCook Reservoir is the largest reservoir in the TARP system. Once completed, this $700-million reservoir facility will receive 38 billion L (10 billion gal) of CSO and flood water via the McCook Main Tunnel, which connects the TARP Mainstream Tunnel to the McCook Reservoir, and from distribution and Des Plaines inflow tunnels which will bring flow from the Des Plaines Tunnel of TARP."

Sep 1, 2016

By Yi Yang, Xiuzhu Su, Wei Sung Ng, Shuiping Zhong, Miao Chen

With over 260 tons of gold reserves, the Shuiyindong gold mine is one of the largest Carlin-type gold deposits in China. A particular challenge in the processing of the ore is the presence of carbonaceous compounds, which can cause substantial losses in recoveries via the preg-robbing and adsorption of gold. To investigate the structural properties of the native carbon and to compare between different characterization techniques for such compounds, pre- and post-flotation mineral samples containing 0.9–4.8% non-carbonate carbon from the Shuiyindong mine have been examined via mineralogical and thermogravimetric approaches, as well as spectroscopic techniques, including X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine edge structure spectroscopy (NEXAFS), solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, Raman spectroscopy and preg-robbing measurements. NEXAFS and DRIFT yielded the most reliable results, indicating that 60–75% of the organic carbon in all samples consist of aliphatic alkenes with substantial unsaturated content, highly similar to activated carbon, with the remainder being graphitic and humic. Speciation by XPS was sub-optimal due to spectral overlaps between graphitic and aliphatic carbon, and between carboxylic and carbonate functionalities, while NMR spectroscopy could not provide reliable speciation of the carbon groups. The preg-robbing strength was strongly correlated to the aliphatic content and structural disorder in the carbon, while no such relationship was found with the graphitic and humic content.

Nov 29, 2021

By J. F. Brune

"Re-occurring face ignitions in U.S. coal mines are concerning and require a closer look at air quality monitoring systems and practices employed in these mines. The explosion disaster at the Upper Big Branch mine in West Virginia in 2010 caused 29 fatal injuries and was largely caused by inadequate water sprays and inadequate ventilation monitoring. In this comparison, the author compares ventilation system monitoring in Australian, German and U.S. underground coal mines and makes recommendations for improvements and best practices. Mines in Germany and Australia are adhering to more stringent requirements for monitoring air quality and quantity and for monitoring water spray systems on cutters to prevent frictional ignitions. Air quality should to be monitored for sufficient oxygen, toxic gases, explosibility and for fire gases indicating a potential fire. Ventilation monitors must also confirm that sufficient quantities of air are available. Fully automated, continuously recording atmospheric monitoring and alarm systems are established practices in Germany and Australia and should be mandated for U.S. mines as well, in addition to the current, regular spot inspections of the ventilation system by certified mine examiners. BACKGROUND: METHANE EXPLOSIONS, FACE IGNITIONS AND NEED FOR AIR QUALITY MONITORING Accumulations of methane in face areas of underground coal mines frequently lead to ignitions that can cause burns, traumatic injuries and, in the case of the 2010 Upper Big Branch disaster, cause major explosions with multiple fatalities. Table 1 shows the number of reported face ignitions in U.S. coal mines between 2010 and 2014, based on statistical data published by MSHA (MSHA 2010 – 2014). Although there appears to be a downward trend in such ignition incidents over time, ignitions continue to occur with some regularity; and each ignition may cause a potentially catastrophic mine explosion.Per regulation, all U.S. coal mining machinery, continuous miners and longwall equipment, is outfitted with continuously monitoring methane sensors wired to cut power to the equipment as the methane level exceeds 1%. Face ignitions keep occurring because these sensors are usually not positioned in sufficiently close proximity to the coal cutting drums or to the freshly exposed coal face where the methane is most likely released. Therefore, methane may accumulate in explosive concentrations near the coal face and the cutting drums long before the gas concentration reaches the 1% level near the monitor and creates an alarm."

Jan 1, 2016

By M. Bunch

"THE SUPER CYCLE IS GONE The utopia of the rising sales volume, for mining companies from 2002-2011, was entirely due to rising production volume and prices. The Australian mining sector experienced an 18 percent annual growth rate in revenues, and 11 percent growth in prices. (1) However, EBIT remained flat during the same time period. In addition, Australian mines saw a 7 percent annual decline in both labor and capital productivity. (2) Mines in the U.S. and Canada produced similar results, whereas the world-wide mining industry has seen a productivity drop of 40% since 2001. (3) The decade “Bull Run” of rising prices was trashed by companies that chased low-quality assets while increasing debt on their balance sheet. It seemed everyone believed the “super cycle” would last forever, while completely ignoring the history of cycle downturns. Worldwide mining operations are as much as 28 percent less productive today than a decade ago, according to new McKinsey research. The results from McKinsey’s new MineLens Productivity Index (MPI), which adjusts for declining ore grades and mine cost inflation, show that the pronounced decline in productivity is evident across different commodities and is seen in most mining players and geographies. (4) McKinsey sees three important areas of focus to address the root causes of productivity decline. 1) Embed effective management operating systems at mines 2) Prioritized operational excellence and capabilities development 3) Focus on innovation Reality has now settled back in and companies are struggling to make ends meet. The basic management staple of controlling costs and improving the production/productivity that was lost in the excitement is now back in play. Traditional cost-cutting approaches, such as across-the-board spending cuts, layoffs, and hiring freezes are only short-term initiatives and will not permanently improve a company’s cost structure or improve long- term competitiveness. This can only be accomplished by engaging front-line employees and empowering them to make necessary improvements in their daily work. It is time for leaders to lead and develop cultures of continuous improvement within their organizations in order to sustain their mining project to the end of mine life. Successful operating managers require two different skill sets of Leadership and Management; knowing how to lead people in their organization and how to manage the work they do."

Jan 1, 2016

By H. Kinilakodi

In 2008, the authors developed a methodology for identifying underground coal mines at high risk for major-hazard events. It focused on major hazard-related violations of safety standards associated with high-risk conditions. Later, using a sample of 103 mines with 2008 and 2009 data, injury measures and U.S. Mine Safety and Health Administration (MSHA) citation data were combined into a safe performance index (SPI). The SPI was used to assess the relative safety-related risk of mines, including by mine-size category. In this paper, comparisons are made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large and medium-sized mines. Mining Engineering, 2011, Vol. 63, No. 10, pp. 73-77. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999

By A. Khoshnevisan

Molybdenum resources around the world are mainly associated with porphyry copper ores. Molybdenite (MoS2) is the main Mo mineral that has rhenium in its crystal lattice. This paper investigates the recovery of rhenium and molybdenum from a molybdenite concentrate using a hydrometallurgical treatment method. The molybdenite concentrate is leached with nitric acid and subjected to solvent extraction to recover and separate rhenium and molybdenum from the leached liquor. The effects of pH and the chemicals? concentration on extraction characteristics of Mo and Re are investigated to define the best condition for selective extraction of these metals. The tested leached liquor contained of 8.2 g/L Mo, 1.5 g/L Fe, 0.5 g/L Cu and 60 ppm Re. A good extraction efficiency, up to 94%, was achieved for Re from the leached liquor, where the extraction of other metals, such as Fe and Cu, was negligible. In particular, at very low pH, rhenium is extracted selectively from solution, while the extraction of molybdenum is less than 10%. After removing rhenium, molybdenum was extracted with LIX984N. The selectivity of molybdenum extraction over other metals in solution was significant. Nearly 94% of molybdenum can be extracted from the solution at a pH value of -0.12, without any interference from other metal ions such as copper and iron.

By R. L. Hudak, R. F. Randolph, A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. The National Institute of Occupational Safety and Health (NIOSH) has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by nine decibels. The “Inquiring Ears Want to Know” fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

"Hecla Limited has been investigating the potential benefits of using a Spendrup/Compact Filter Technic (CFT) diesel filtration system to remove diesel particulate matter (DPM) from the mine atmosphere to optimize use of the available air. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the scrubber efficiency for dust and DPM which is to be presented in another report. This paper reports on a new mining application of a carbon particulate sensor’s ability to continuously monitor long-term mine DPM levels in conjunction with the scrubber evaluation. Magee Scientific is the manufacturer of the Aethalometer®, a continuous black carbon monitor which has been used extensively in worldwide ambient air quality monitoring networks. Two Aethalometers were used at the mine to assess their potential to continuously track underground DPM levels. In this first underground mine application, the Aethalometers were used to continually monitor black carbon (BC) in the intake and exhaust of the CFT scrubber system. Results showed that an off-the-shelf Model AE33 Aethalometer could continually track underground BC levels for extended periods of time over the course of the six-week trial. Data at the scrubber intake over 14 days of testing showed that DPM filtration would be required less than half of the time to maintain BC levels below 50 µg/m3. If the Aethalometer BC data output were “smart coupled” to control a 200-HP in-mine scrubber, significant electrical cost savings would be realized. INTRODUCTION Mine ventilation airflow quantities are calculated to maintain a safe and healthy environment for miners. Dilution of diesel particulate matter (DPM) is often a key factor used to determine the required quantities of ventilation air (Bugarski et al. 2011). DPM emissions and exposure levels are highly variable depending on mine schedules and activities (Janisko & Noll 2010); however, lacking technology to continuously monitor levels, mine ventilation systems are often over-designed in order to handle worst-case scenarios to ensure that DPM levels are maintained at or below regulatory limits. As mines go deeper it becomes more difficult to supply air, and the development of new shafts for air is not economically feasible (Basu et al. 2008). Cleaning and reuse of available air then becomes an attractive option to maintain good air quality."

Jan 1, 2016

By N. Akbulut, A. Anani

From the initial planning phases to the closing of a mine, mining is an industry where high attention, care, and sensitivity are needed in every step of the mine life. Since mining projects have a long-life span, exceeding a decade sometimes, managing a whole mine project is challenging, especially when challenges faced due to generational differences are considered, such as tracking and logging data, or the usage of different engineering solutions change over time. Along with the overall hardship caused by the time put into a mining project, the present-time operations are very costly where each minute counts. In present-time operations, every decision made, and every minute used during planning and operations has an impact on the efficiency, safety, and economics of the project. Having extremely harsh conditions in both the excavation and mineral processing operations not only slows down the processes but creates very dangerous environments that need to be handled with precise safety measurements. To support the already established processes, we could implement new technologies and use them to our advantage. Virtual reality (VR) is one of these technologies that we could implement in the mining industry. VR is a technology that emerged in the 1960s creating virtual environments and platforms. The user experiences these virtual environments from head- mounted headsets to rooms with 360 screens, all with different levels of immersion. These higher levels of immersion, create a higher level of presencemaking the users more engaged in the activity they are trying to accomplish. These two factors of immersion and presence are what make VR unique and beneficial. VR has some applications and case studies in the industry along with some research being conducted in universities. Unfortunately, there has not been a comprehensive literature review or analysis regarding only VR and its implementations for the mining industry in the last 5 years. This paper aims to describe what VR is and its relation to the mining industry, in the most recent years. The paper first gives a brief background on what VR is and its key concepts. Secondly, it will give information on how the initial stages of the literature review were conducted and the findings along with discussions. The paper will finish with the conclusion drawn from the discussion and potential future work.

Feb 1, 2023

By Cheng Li, Yanlei Wang, Lingrui Kong, Jianxin Tang, Fang Yuan

Coal mined-out areas have a significant impact on mining safety and affect the pressure distributions of neighboring coal faces. The PFC3D software is used to study the goaf mechanical characteristics, and the core loading test verifies the rationality of the numerical simulation method. The results from the numerical modeling showed that the void ratio, particle size ratio, and particle size distribution of the rock particle sample (RPS) had a significantly remarkable influence on the compression deformation characteristics of the rock block. The parallel-bond tensile strength and parallel-bond cohesion had a notable impact on the compression deformation traits of the rock block only when the axial stress level was lower than 12 MPa. By contrast, when the axial stress exceeded 5 MPa, the effective modulus significantly influenced the compression deformation features. However, the stiffness ratio, loading rate, and parallel-bond friction angle had almost no effect on the compression deformation characteristics. Furthermore, when the stress level was less than 10 MPa, the stress–strain curves from the rock core samples’ numerical simulation and loading tests were approximately linear. In addition, the Pearson correlation coefficients of the stress–strain curves suggest that the goaf zone’s core numerical simulation results had a robust correlation with the loading test results. The findings of this study can serve as a reference for the field application of PFC3D software and safety assessments in goaves.

Jan 18, 2022

By E. J. Haas, K. A. Rost

"This study sought to identify changes in continuous mining machine (CMM) operators’ risk perception and risk behaviors as a result of adding a proximity detection system (PDS) into their environment. To accomplish this research task, 9 CMM operators from 5 locations were interviewed. Interviews were thematically analyzed for constructs including patterns in risk perception and behavior before and after PDS integration and the process of adapting to the PDS. Operators discussed standing in the red zone less than they did before using the PDS; however, they also discussed other risky decisions they made while learning how to operate their CMM with the PDS technology such as “cheating” the technology and working faster to meet production goals. The process of relearning job tasks with technology and unintended behaviors as a result of that relearning process need to be taken into account when introducing new technology into the mine environment. The study results show an in-depth view of mine workers’ perspectives and how their job tasks and environment could be or are affected when learning how to use new technology that are relevant to companies and mine operators when introducing new technology into the mine environment. INTRODUCTION Established “red zones” can help prevent striking and pinning incidents by providing guidance to continuous mining machine (CMM) operators about where they should stand and not stand while operating a CMM. Although red zones influence operator placement positions, these guidelines are not foolproof safety mechanisms. Depending on the job task and circumstances of the mine environment, a CMM operator may unintentionally or intentionally stand in a red zone. For example, CMM operators may work in close proximity to their CMM for better visual attention cues and the ability to work at a higher rate of production [1-3]. To further enhance protection and prevent collisions between vehicles and mine workers, a proximity detection system (PDS) was developed for the industry. The PDS determines an individual’s position relative to a specific piece of machinery, issues visual and/or audible warnings to the mine worker to change positions, and, if necessary, disables machine motion [4]. The introduction of new technology within other sectors has been identified as a factor that influences work decisions. Specifically, previous research demonstrates that when technology debuts there can be an initial intrinsic risk perceived among users about how the technology will interact with their current environment and behaviors; however, these ambiguities, including the possible risks and benefits, are seldom studied [5]. Some research suggests that the constant presence of technology can disrupt situation awareness and decision-making capabilities by increasing worker responsibilities and worker cognitive demands [6-8]. Further, if workers’ perceived risks both with and without technology are misjudged, unsafe decisions that result in human error and injury may be more likely [9-11]. Although these statements are provided within a broad contextual framework, they support the need to study how technology is perceived among end users in their own environment. Because research about technological impact on worker behaviors has suggested both positive and negative consequences of technology, this issue is worth addressing in the mining industry. Specifically, research has not determined whether CMM operators view their placement choices in the red zone as safe or risky and what effect PDS technology has, if any, on risk perception and subsequent risk behavior."

Jan 1, 2015

By D. Dunbar

Flooding of open pits now receives considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit lake deep waters can effectively eliminate oxidation of pit-wall sulphides. A state-of-the-art, coupled physical-geochemical pit lake model is used to verify that a cost-effective, environmentally responsible closure strategy for the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia is to adopt a controlled, two-stage infilling of the open pit upon cessation of operations. By filling the pit initially with highly saline waters from evaporation/infiltration basins and naturally saline deep groundwater, followed by capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within 1 to 2 years, followed by the rapid onset of sulphate reducing conditions in the bottom waters. Hydrogen sulphide produced by sulphate reduction will readily react with dissolved metals to form highly insoluble metal sulphides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental management strategies. The proposed plan allows for: 1) safe storage of saline evaporation basin waters; 2) the potential for passive treatment in anoxic bottom waters of ARD seepages from other mine site operations should they arise; and 3) a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2001

By Nikhil Dhawan, Amit Barnwal

The present study reports a processing route to recover metals from integrated circuits of discarded random access memory (RAM) units containing ~ 66% printed circuit boards and ~ 33% integrated circuits. The integrated circuits are manually separated, grounded, classified, and subjected to water fluidization for the effective separation of metals. The significant separation was achieved via water fluidization, and the underflow fraction was magnetically separated. The magnetic fraction was thermally exposed in a muffle furnace, and the process optimization was carried out using a Box-Behnken statistical design. The detailed characterization at subsequent steps significantly aids the understanding of metal-plastic separation and enrichment. A concentrate containing 97% metals (Fe-59%, Ni-9.5%, Cu-7.7%, Sn-13.4%, Pb-5.6%, Ag-1.6%) with 96 wt% recovery can be recovered from discarded IC units. The process pursued is simple, adaptable, and environment-friendly, and the product can be used in conventional smelters.

Jun 23, 2020

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By J. Olsson

Introduction Stainless steel has by tradition been a common construction material for hydrometallurgy processes and the most common grades can be found amongst the ASTM 300-series, i.e. austenitic grades of type 304L, 316L and 317L. However, there are a number of new grades available today, which imply more cost effective solutions for those designing plants where good resistance to acids, containing the desired metal ions, often contaminated with chlorides and other halides, is the key issue. There are austenitic-ferritic or duplex grades having the same or even better corrosion resistance than the austenitic grades and approximately twice the strength, which enables design in thinner gauges, which in turn implies less weight and less cost. They have also excellent engineering properties, enabling fabrication of process equipment, machinery and different types of tanks. On top of that, they contain less nickel and molybdenum than their austenitic counterparts, which implies not only lower cost for alloying elements, but also a more stable price when considering the price fluctuations for these alloying elements during the last years. This paper describes briefly the family of duplex stainless steel and it presents a number of relevant corrosion tests where duplex grades have been compared with austenitic grades. The results have in several cases been verified by in-plant exposures in zinc and copper production plants. It also describes applications and experience of duplex grades within a variety of hydrometallurgy plants. Installations of highly alloyed austenitic grades will be described as well. The corrosion tests and service experience reported cover hydrometallurgical processes based on sulphuric acid.

Jan 1, 2007