Search Documents

By Andrzej Luszczkiewicz, Kazimierz S. Sztaba

Flotation tailing of Polish copper sulfide ores represents more than 90% of the mass of run-of-mine ore. The tailing contains mainly quartz, dolomite, clay minerals, traces of sulfides, and some accessory minerals. Almost all minerals of the tailing are well liberated and, therefore, any further beneficiation process applied to the tailing is expected to be inexpensive. In this work, results of investigations on utilization of flotation tailing using classification and gravity concentration are presented. It is shown that due to classification of flotation tailing in hydrocyclones, the coarse fraction becomes suitable material for gravity separation providing backfill material for underground mines as well as heavy minerals, a source of valuable rare elements. It was also found that heavy minerals separated by gravity methods contain a significant amount of rare elements such as zirconium, titanium, silver, rare earth metals, and uranium. The light fraction of the gravity separation contains well deslimed quartz particles and meets strict requirements for hydraulic filling material ked for structural support in underground mines. Evaluation of the cost of the proposed technology indicated that investment to implement the method would provide a return within 2-4 years.

Jan 1, 1995

By P. D. Rao, D. E. Walsh

A pilot-scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2 in.) crushed ore from Ester Dome, AK. 9.04 t (9.94 st) of crushed ore were sampled and processed through a Pan-American jig-Wilfley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/t (22.4 oz/st). The feed grade to the plant was calculated at 1.71 g/t (0.05 oz/st). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/t (0.042 oz/st), 1.30 g/t (0.038 oz/st), and 5.47 g/t (0.16 oz/st, respectively. Significant coarse, free-milling gold values were shown to remain in the, jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1992

By Scott Stebbins

Cost estimating and economic evaluation software provide evaluators with the ability to predict the profit potentials associated with mine design alternatives even during project exploration and prefeasibility. Examining a multitude of development alternatives early on serves to identify aspects critical to profitability and to increase the reliability of economic projections. A case history illustrates how Sherpa Cost Estimating Software, when used in conjunction with Apex Software for Economic Evaluation, significantly enhances an evaluator's ability to examine design alternatives in a timely and reliable manner. The costs and economic impacts associated with various access routes, production rates, equipment mixes, and stoping methods are projected.

Jan 1, 2002

By D. III Earley, R. L. Blake

The Bureau of Mines is investigating the potential for in situ mining (ISM) of gold and silver mineralization. This preliminary study examined samples from several types of deposits. It used light optical microscopy and the electron microprobe to characterize the ore and gangue minerals and textural features of these samples. This included the spacial relations between the target minerals and likely natural fluid channel ways. Low-grade disseminated deposit types from the western US were found to contain fracture- hosted or matrix-hosted gold and silver minerals, some of which are encapsulated by quartz or pyrite. Successful ISM application to gold and silver deposits needs this data in order to understand potential problems of the lixiviant reaching the ore minerals.

Jan 1, 1991

By K. Terhaar, K. Prisbrey

The objective was to determine operating protocols for a lead and silver column flotation cleaner being considered for installation at Sunshine Precious Metals Inc. 's Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause-and-effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feed grade. The results were that xanthate, zinc sulfate and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences are useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training and provide a foundation for future on-line control.

Jan 1, 2002

By A. I. Makhin, S. M. Sablukov, V. K. Sobolev, V. A. Larchenko, V. S. Shchukin

The kimberlites of northern Europe are related with a large crustal block having a northwest-southeast orientation. Kimberlites penetrate the Archean formations of crystalline basement, Late Proterozoic rocks, which are overlapped by Middle Carboniferous and younger deposits. The kimberlites bodies include pipes, dikes and sills of Upper Devonian age. Within the region, rocks of two magmatic series form diamond-bearing kimberlites. Aluminum rocks form a new type of diamond-bearing rock that is not found in other diamond provinces. Kimberlites of this region are characterized by highly developed deuteric alterations, a low content of associate minerals, the presence of two diamond generations and an increased content of jewelry-grade diamonds.

Jan 1, 1997

By D. J. Kennedy, W. G. Klinowski

Over the past few years the Cape Breton Coal Research Laboratory's staff designed, built, tested and proved the necessary hardware, software and methodology of tracer gas based surveying techniques applied in the field of mine ventilation. These methods are now used routinely in a variety of applications where traditional anemometric methods do not provide the required accuracies or cannot be effectively employed. Irregular or highly turbulent flows, leakages, geometrically complicated or highly obstructed airways are just a few examples where traditional anemometry can produce unacceptable errors in calculated ventilation parameters. Tracer gas based ventilation techniques have been used in many problematic situations where the standard ventilation methods are inadequate. One such problem, faced by many mine operators, is the emergency imposed by the ever present threat of a mine fire. An understanding of the propagation of smoke contaminants and the demonstrated integrity of appointed escape routes can save lives and property during a fire. That knowledge can be gained quickly and inexpensively by the application of tracer gas smoke simulation methods. The concept of controlled air recirculation has recently gained considerable attention in the mining industry. While mathematical models can be used to predict performance, the ultimate proof of a ventilation system's performance can best be provided by a tracer gas based simulation of contaminant levels. Fan performance tests and assessment of auxiliary ventilation systems are highly dependent on accurate definition of airflows; precise data can be easily obtained by tracer gas based volumetric surveys. This paper contains a brief description of the equipment and the methodology of tracer gas based ventilation techniques and presents typical examples of their use

Jan 1, 1991

By J. A. Finch, J. Yiantatos, A. R. Laplante

This paper re-examines the mixing conditions in the collection zone of flotation columns. These have in the past been characterized with a single uniaxial dispersion coefficient, E. The relationship between E and column diameter, Dc, is examined based on residence time distributions (RTDs) in columns of Dc ranging from 5.lcm to 184cm. Results agree with published correlations in chemical engineering, i.e. E a Dc '" , Data explain why pilot columns display significant upgrading between the feed level and the interface, whereas plant columns do not. It also suggests that, for plant columns, the full collection zone (up to the interface) can be considered when calculating the residence time. A mathematical model considering two regions of different mixing was compared to the single E model. Both models adequately fitted measured age distributions inside the column and overall RTDs. Measured and simulated mixing characteristics are compared to those of flotation banks, using a tanks-in-series approach; banks of comparable mixing to columns are identified.

Jan 1, 1988

By Tso-Min Shih, Ching-Hua Liu, Chung-Jen Lin, Hsi-Chiang Fang

This paper presented herein, describe the special design of an open type coal dust explosion apparatus and the laboratory works for investigating the effectiveness of the parameters on coal dust explosion and the prevention of the propagation of the coal dust explosion flame. Coal sample which were taken from the San-Ying collieries, were passed through the process of crushing ,grinding and screening to get the required particle size, ranged from 40 mesh to 200 mesh under size for testing purpose, the rock dust spreaded on the surface of coal dust and water mixed with coal dusts were employed for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1991

By I. Iwasaki, K. A. Smith, X. Cheng

The reaction mechanism for the cathodic decomposition of pyrrhotite in deoxygenated solutions at natural, near neutral pH levels was studied using potential and cyclic voltammetric measurements. Reaction products on the pyrrhotite surfaces were examined by Auger Electron Spectroscopy (AES), by X-ray photoelectron spectroscopy (XPS) and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using an ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least-squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by performing microflotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1995

By J. B. Hiskey, S. Chander, B. J. Scheiner

The use of selected iron complexing agents in preventing or ameliorating acid mine drainage was investigated. The experiments were conducted in weathering columns using refuse samples from a coal cleaning plant. It was observed that the treatment with iron complexing agents significantly altered the rate of oxidation. Some of the reagents tested reduced the rate of oxidation whereas the others even enhanced it. The results showed that a commercial reagent containing oleyl imidazoline was most effective in retarding the oxidation rate. In addition, a simple treatment with this reagent substantially decreased the rate of oxidation of pyrite in a column that was generating acid at a high rate. The effect of this reagent on the surface properties of pyrite was studied by cyclic voltammetry and zeta potential measurements. The decrease in the rate of oxidation resulted from suppression of both anodic and cathodic reactions at the surface of pyrite.

Jan 1, 1993

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov, D. V. Magazanik

Based on theoretical and experimental researches of phosphate and carbonate minerals flotation in the presence of soluable glass at various pH values and sodium silicate concentrations, it has been established that the presence of soluble glass in solution leads to formation of silicate compounds on the surface of phosphate and carbonate minerals causing change in their floatability for the worse. The harmful influence of soluable salts is done by tying of collector as metallic soaps, forming precipitates on the surface of minerals to be floated and causing their depression of flotation, and breaching of the froth etc. Depressing action of slimes and products of interaction with collector depends on the ratio of values and signs of potentials of the mineral surfaces. The possibility of phosphate and gangue minerals separation can be evaluated by comparing the minimum-necessary concentrations of collector required for their flotation.

Jan 1, 2002

By Samuel Frimpong

In this paper, the authors present a typical mine profitability model. The method of generating system moments is used to examine the sensitivity of the profitability function to changes in the dependent variables, and to express the expected risk associated with undertaking the project in a predicted economic and technical environment. Profitability of a mining venture is a function of many variables ore grade, capital and operating costs, milling efficiency, ore reserve tonnage and annual tonnage, equity - loan structure, tax regime, etc. Estimates of the expected value and the variance of the profitability function are obtained by calculating the partial derivatives of the function with respect to the dependent variables, using the Taylor series expansion method to the second order. Sensitivity analysis is carried out by examining the effects of each variable on the profitability function, which is determined by the magnitude of the product of its partial derivative and variance. An appropriate probability density function, based on the expected value and the variance of the profitability function, is assumed to estimate the expected risk associated with the project. This expected risk is a measure of the area under the profitability density function below the appropriate, selected discount rate or the cut-off net present value (NPV). The results are compared with those obtained by using the Monte Carlo simulation technique, and they show that either of the two methods could be used to evaluate the probability of project failure or success with no significant difference.

Jan 1, 1992

By A. Cordonnier, Ch. Obry, R. Evrard

In spite of the large annual expenditures and the vast field of activity covered, it cannot be said that many new grinding machines have actually come to light and modified the existing market for more than half a century. Manufacturers have mainly made advances in increasing machine sizes, efficiency and reliability, and in machine automation. The relatively recent emergence of roller presses is the only exception to this homogenisation of machine ranges. The development of roller presses in pregrinding has shown the advantages of compression grinding over the ball mill from the power consumption point of view. But classical roller presses still have maintenance problems due to the high grinding pressure. The FCB Research Centre has carried out much work in this field and in particular has studied the advantages of this process in pregrinding and integral grinding. These researches lead to the development of two new compression grinding machines. The first one, HOROMILL®, presented for the first time on the 8th European symposium on comminution at Stockholm, finds its application in the field of fine to very fine grinding in dry process. The second one, RHODAX®, presented at INTERMAT in Paris, covers the field of secondary and tertiary crushing and the first stage of grinding for most of the minerals in dry or wet process. Its high reduction factor permits to do with only one machine the work realised today with two or three crushing/milling stages. These two complementary machines offer a wide range of combination summarised on [Figure 1].

Jan 1, 1995

By S. A. F. Murrell, M. Hong, L. J. Bond

This paper investigates the propagation, interaction and scattering of explosively generated seismic waves with discontinuities in rock masses using numerical models which employ a finite difference method. The models consider 2-D systems and give a full solution including mode-conversion in the mid-frequency scattering region where feature dimensions are of the order of the wavelengths involved. The paper has two parts, the first of which considers wave propagation and diffraction by simulating an explosive body source in a half- space containing a step or a slot on the surface which represent a cliff and a rift valley that has dimensions of the order of the wavelengths in the source. The second part of the paper reports a hybrid technique which combines a perturbation method and the finite difference method for wave propagation again caused by an explosive body source in a 2-D half-space system but with a shallow surface obstacle, such as a smooth ridge, with elastic constants slightly different from bulk material and the slope of this surface topography are shallow. This hybrid technique is also reported being applied to a half-space with a horizontal void or insert.

Jan 1, 1986

By Todor P. Stefanov

The thermal draught within ventilation networks of underground mines depends to a great extent on the shafts depths and degree of change of ventilating air density. When the topology and space orientation of a ventilation network are constant, the dynamics of thermal draught is determined mainly by the variations of the heat- and mass-transfer processes in the openings. This conclusion follows from the well known basic theoretical notions about the thermal draught-aerostatics and thermodynamics [1]. Quantitative evaluation about the influence of heat- and mass-transfer processes on dynamics of thermal draught could be made through: direct mine measurements, special experiments and with the aid of mathematical models. The first two methods produce sufficiently accurative results, however it is very difficult to perform such studies, particularly when these processes are evaluated within a large scope and multifactor aspects. Mathematical models of thermal draught allow to overcome easily these difficulties. The degree of accuracy of results, obtained by this method, depends to a great extent on the degree of approximation achieved by the model to the real heat- and mass-transfer processes. In this paper, with the aid of Bulgarian developed method, algorithm and computer program V WT-4 - for complex evaluation of ventilation parameters in active mine ventilation networks [2], the authors investigate some changes in the thermal draught. Basically, the method is an iterating evaluation of an open set of equations, which represents relationships between the following basic parameters of a mine ventilation network: [ ]

Jan 1, 1980

By K. Y. Haramy, E. C. Westman

Anomalous geologic or stress conditions ahead of a longwall face have the potential of causing great harm to both the individual miner and the mining operation as a whole. NSA Engineering has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of afield effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration that was likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with the laboratory measurements.

Jan 1, 1997

By Andrew I. Hustrulid

The discrete element method has successfully been used to model the behavior of material flow in transfer stations. With position, velocity, and applied forces for every particle and boundary in the simulation available at increments of 10-5 seconds, the next critical step is the presentation of this data in a concise and beneficial form. This paper discusses several methods of presenting the data from discrete element simulations that are used to improve the performance of a transfer station. These measurements are also used as a learning tool to better understand and visualize how material transfers from one belt to the next.

Jan 1, 1998

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979