Search Documents

By Jack G. Crump

Nuclear radiation systems for gauging solids content in process slurries and level in crushers has demonstrated acceptance in ore processing. The use of nuclear radiation for moisture analysis of bulk materials is presently receiving acceptance in beneficiating and agglomerating processes. On the horizon is the use of nuclear activation methods for continuous, qualatative and quantitative analysis of concentrate. The common characteristics of these uses of radiation is the non-contacting nature of the measurement. Unquestionably, this is the dominant reason for acceptance of nuclear methods in level and slurry-gauging. Moisture activation analysis of a product using nuclear methods retain this advantage. However, and: more importantly, they offer new solutions to old problems. The nuclear method in addition to being non-contacting, is non-destructive and provides a continuous measurement of the process variable. The system responds: to the fundamental makeup of matter, mass and elemental composition, not to secondary properties such as temperature, resistivity, or dielectric constant. Measurement is a volume rather than a surface phenomenon, thus the results can provide a truer pricture of the measured variable.

Jan 1, 1965

By Franklin H. Sharp

During the last few years the New Lead Belt of South- eastern Missouri has become the main source of lead in the United States. It also produces significant amounts of zinc, copper, and silver. The mines are located on a narrow, mineralized trend extending southward from Viburnum, Missouri for about thirty-five miles. The area is part of the Ozark uplift and consists of steep-sided, heavily wooded hills with narrow valleys. Surface streams are very erratic, normally having low flows but becoming rushing torrents during the violent thunderstorms that occasionally occur. Because of the pristine nature of the country and the newness of the mining developments, the environmental impact of all phases has been closely watched.

Jan 1, 1973

By A. J. Rergis

During the past ten years a number of papers have appeared describing zeolite occurrences in the western United States in Mesozoic sedimentary rocks, altered bedded Tertiary pyroclastics, playa lakes, hot springs, and amygdaloidal basalts. With the emergence of natural zeolites as economic industrial minerals it appears, useful to develop a system of classification to delineate those zeolite deposits of economic interest which were not discovered until the middle 1950's. The first attempt at a classification of naturally occurring zeolites was made in 1914 by Lindgren l when he classified the zeolites into eleven groups based on their mode of occurrence. The zoned zeolites in the Mesozoic rocks of New Zealand and elsewhere were classified according to the mineral assemblages by Fyfe, et al.2 in 1958 as a zeolite facies corresponding to low grade regional metamorphism. In 1966, Hay suggested as an alternative to the preceding classification one which would "classify as diagenetic all mineral assemblages produced in sedimentary rocks under conditions in which zeolites are formed." In this paper a classification is proposed with the objective of providing an overall perspective of the zeolite occurrences in the western United States.

Jan 1, 1967

By J. M. Mutmansky

A number of previous publications have attempted to provide the practicing ventilation engineer with simple guidelines on the optimal velocity to be used in mine openings. Some of these velocities were meant to be used in metal mining operations and some were meant for coal mining. A careful review of these publications reveals that the optimal velocities were determined based upon assumptions that are not existent today. As a result, they are not suitable for use in a modern coal mine. This paper takes a new look at this problem and determines a statistical relationship for optimal velocity that can be applied under both current and future conditions. The analysis performed here is based upon the determination of the optimal velocity for coal mine entries under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. A total of 8400 different conditions were analyzed for optimal velocity using computer calculation of the capital and operating cost values. Using the individual values of the optimal velocity derived in the calculations, a linear regression equation was fitted to the data to relate the optimal velocity to the other six variables outlined above. This regression relationship allows the ventilation engineer to make an easy, rapid determination of the optimal velocity.

Jan 1, 1984

By Randhir S. Sehgal

After some decades of lying low and being treated as a second rate fuel, coal is back in the news. Production is rising. Predictions are for an ever expanding use, and they differ only in their rates of increase. Even the FBI is involved in trying to stop fraudulent sales of non-existent coal lands and leases to the innocent. In short, we have a nearly chaotic boom on our hands. Obviously our energy production base is in the process of undergoing a major shift, and the process will present many problems. However, there is little doubt that the industry has the basic strength and organization to be able to deal with the new issues that will arise as a result of these shifts in production and use of coal. After all, it does produce nearly 800 M tpy now, and coal is the single biggest fuel for generation of electricity. This role of coal is illustrated in the table below, which shows the coal equivalent quantities of various fuels used in the production of electricity.

Jan 1, 1980

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993

By R. Klimpel

Recent work has shown that the measurement of flotation kinetics in the laboratory is useful in providing guidelines on how operating sulfide flotation plant performance can be improved. This work outlines the influence of various factors on flotation kinetics such as collector/frother type and concentration, particle size, and frother blending.

Jan 1, 1981

By John B. Goddard

The discovery of rhenium on the ion exchange resin used at the uranium in-situ leach operations at Palangana (Texas) led to a laboratory study on the possible methods of recovery. Rhenium, present in small amounts in the ammonium carbonate leach liquors as the perrhenate anion, Re04-, concentrated on the anion exchange resin, which was a factor of ten more selective for rhenium than for uranium. Various elution systems were investigated for stripping the rhenium from the columns after the uranium had been eluted with chloride or nitrate solutions. Although the perchlorate ion was most efficient on a molar basis, nitrate ion combined the benefits of efficiency and low cost. A 3[N] or stronger concentration of nitrate containing up to 0.5[N] H+ was found to be the system of choice. A rhenium sulfide concentrate containing up to 14% Re was obtained from these effluents by hydrogen sulfide precipitation. Preliminary experiments were run to produce rhenium metal powder by oxidation of the concentrate to NH4Re04 followed by hydrogen reduction at elevated temperature.

Jan 1, 1982

By B. Pesic

This is an extension of the work on recovery of silver and manganese from Ag-Mn ores, and recovery of silver and gallium from flue dust from phosphate industry. Carbon adsorption was considered as the most adequate method for recovery of silver from thiourea leach solutions. For this reason it was decided to examine the characteristics of adsorption of silver on activated carbon. Coconut hard shell activated carbon was used for this study. Ag(TU)2C1 complex was dissolved into thiourea solution to give 2 gpl stock solution. Thy studied parameters were: loading isotherms at 25°C, 35°C, and 45°C, initial kinetics as a function of thiourea concentration, temperature, pH, N2, and O2. It was found that the loading capacity of carbon for silver and thiourea was 137-150 mg/g and 514 mg/g, respectively, at 25 °C.

Jan 1, 1986

By F. M. Benavides

The mining complex being analyzed consists of four mines and two processing plants located in an area where there are several existing modes of transportation. Figure 1 shows a map of the general layout of the four proposed mines and the two existing processing plants. The mines are identified by the numerals "I" through "IV" and the plants by the letters "A" and "B". A proposed overland conveyor would collect the product from all four mines and convey it to Processing Plant A. Alternate transportation systems are as follows: Railroad transport from Mines I and II to Plant B; Highway trucking from Mines I and II to Plant A; Off-the-road truck haulage from Mine III to Plant B and from Mine IV to Plant A. River transportation from the mines to the processing plants was not considered in this study under the assumption that the high capital investments for the loading and unloading facilities, in addition to difficult traffic problems, would make this mode of transportation unattractive.

Jan 1, 1980

By Dean Treweek, Anthony Harding

"Creating stable, safe, constructible and cost effective support to openings in segmental linings is often an important component of successful delivery of a tunnel project. The many constraints on successful implementation include operational, spatial, geotechnical, structural, and constructability. Failure to address these adequately can lead to significant impacts on cost, schedule, and safety. With reference to past project experiences, this paper provides a guide to the most commonly deployed solutions and their pros and cons to help designers quickly identify the most appropriate solutions for a particular project, or act as a starting point for developing new and/or project specific solutions. It highlights the challenges that designers and contractors must address together for successful support of tunnel openings, and the constraints that arise. It then describes the common structural forms of support, and how each form can mitigate the constraints, allowing an effective opening support system to be implemented. INTRODUCTION While only a small portion of the total excavated volume of a typical tunnel, cross passages are often one of the most complex elements of a bored tunnel to construct. Cross passages in soft ground typically involve ground improvement, groundwater control, and multiple temporary support measures to ensure safe construction in ground that has been overstressed due to the construction of the running tunnels. Permanent lining construction requires careful detailing of waterproofing and reinforcement to support both long term ground and water loads and support the broken out rings of the main lining. While there is not a great deal of literature specific to cross passage construction, the main issues are discussed in some detail by Lawrence and Taylor (2011). However, the temporary support of the running tunnel segmental linings during cross passage construction is not always given the attention it deserves. The authors have been unable to find much literature on the design of such systems, much less the considerations that have led to a particular solution. Lawrence and Taylor only mention two potential methods of support. It may be easy to dismiss the opening support as an inconsequential item, but selection of the wrong support type can have significant impacts on both cost and schedule."

Jan 1, 2016

By Young C. Kim

Use of geostatistics to solve mining problems is gaining importance as the cost of developing new mines is increasing and there is a need to mine more marginal deposits. But, until recently, coal companies have shown little or no interest in geostatistics. However, the stringent quality controls on coal burning has led to a surge in interest in improved methods for estimating clean coal characteristics. Until now, most of the geostatistical applications have centered on the problems of estimating in-situ coal characteristics (Sabourin, 1975; Wood, 1976, 1979; Fang and Stark, 1976; Pauncz and Nixon, 1979; and Knudsen et al., 1980). Little work has been done in applying geostatistics to coal washability, except that by Armstrong (1980). Applying geostatistics to coal washability basically means the estimation of cleaned coal characteristics, with the aid of geostatistics. Cleaned coal estimation plays a very important role in overall emission control strategy, as can be seen by the general flow diagram of such a strategy shown in Figure 1. The scope of this paper is limited to one aspect of the overall emission control strategy shown in Figure 1; namely, the prediction of cleaned coal characteristics using geostatistics.

Jan 1, 1982

By L. G. Austin

A simple finite difference algorithm has been used to compute a simulation model for unsteady-state ball milling. The model considers the mill to act as if it were three fully-mixed reactors in series (one-large/two- small), it incorporates the-Rogers-Austin mass transfer law relating mill hold-up to flow rate through the mill, and it allows for the reduction in breakage rates caused by over-filling of the mill at high flow rates. The computation is rapid and requires only small storage space. Examples are given of use of the model.

Jan 1, 1984

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

By George K. Martin

This paper deals primarily with roof bolting in Kentucky coal mines from January 1, 1949, through December 31, 1954, a six year period. The Consolidation Coal Co? (Ky.), a division of the Pittsburgh Consolidation Coal Co., began systemmatic roof bolting in November 1948 in Mine #204, Elkhorn #3 Seam, at Jenkins, Kentucky, After the efficiency of roof bolting had been proven by the Consolidation Coal Co., this procedure was adopted by other companies throughout the state. In December 1954, approximately 46.4 percent of Kentucky's total production of coal from underground mines was obtained from roof-bolted areas. Statistics in this report will show the progress made in roof bolting during the six years, in addition to the roof bolting being done as of December 31, 1955. Significant progress has been made in the coal mines of Kentucky in reducing the roof-fall fatality, rates, during the past several years by adopting systemmatic roof bolting. The ground work by the Consolidation Coal Co, (Ky.) in cooperation with the Federal Bureau of Mines was based upon the previous experience of the St. Joseph Lead. Cc, in its Southeastern Missouri Mines and The Tennessee Coal and Iron Division of the United States Steel Corporation. The author gratefully acknowledges the cooperation and assistance given by officials of the various mining firms using roof bolts, the Kentucky Department of Mines and Minerals, and the Federal Bureau of Mines in furnishing photographs and information.

Jan 1, 1958

By I. Iwasaki

The effects of autogenous grinding and conventional grinding on the floatabilities of copper-nickel sulfides were investigated as a part of a pilot-plant development project on the differential flotation of Duluth gabbro. At the same mesh-of-grind copper, nickel, and cobalt recoveries were higher and residual sulfur in the flotation tailings was lower with the autogenously-ground pulps. With the ball-mill-ground pulps the residual sulfur in the tailings could not be lowered to the level attained by the autogenously-ground pulps even at increased levels of the collector addition. From mineralogical examinations of concentrate and tailings samples, an electrochemical interaction between grinding media and sulfide minerals was thought to have a greater effect on sulfide mineral flotation behavior than the breakage characteristics of the ore samples in these two types of mills.

Jan 1, 1981

By P. D. Morrell

Jetbelt is the trade name for the air supported belt conveyor. It does not use troughing rollers. Jetbelt conveyors support the conveyor belt on a thin film of air. The belt rides in a steel trough which has small holes equally spaced along the bottom of the trough. Air comes through the holes under the belt, thereby supporting the belt. The air pressure is provided by a single centrifugal blower that creates very low pressure, between 249 Pa and747 Pa [10" and 30" water column], depending upon the tonnage being conveyed. The volume of air required ranges between .001415 m3/S and .00283 m3/S [3 and 6 CFM] per lineal foot of conveyor. Therefore, depending on tonnage being conveyed, a 304.8m[1000'] conveyor might require as little as 1.415m3/S [3000 CFM] or as much as 2.83m3/S [6000 CFM.]. (See Figure 1) Horsepower requirements can be less than troughing idler conveyors and considerably less than some other forms of bulk conveying. Savings are most significant in horizontal and down hill (regenerative) conveyor designs. Horsepower to lift material, of course, does not change.

Jan 1, 1984

By Joseph O. Cook

I know this is, at best, a frustrating period for the coal mining industry. About 20,000 miners have been laid off, mostly in the Appalachian and mid-western areas, and several mines are working less than 5 days a week; however, the industry is experiencing modern growth and, at least, there is the potential for future growth. The coal industry is probably only operating at about 80 percent of its present capacity, and it is certainly capable of helping this country solve its energy problems. Growth, as a rule, does not come easy, and growth in the coal industry is no exception to this rule. Many formidable challenges have to be overcome. As we all know, mining relies very heavily on the earth sciences, which have advanced significantly in the past few years, but we are always working in a changing environment which in most cases is a hostile environment. Large quantities of material are quickly extracted and rapidly moved in, generally speaking, a very confined area. The very nature of the mining business directly and constantly impacts our environment during this period in which the Nation and the world has become increasingly smaller and more concerned about protecting our environment. In addition, growth brings about an expanding work force which is increasingly younger and less experienced.

Jan 1, 1980

By Alcides Freitas

The great importance of aggregates as a basic building and maintenance material for both public and private projects makes the identification and availability of this valuable resource imperative for our economic and social well being. This was one of the main reasons that led the California Legislature to enact the Surface Mining and Reclamation Act of 1975 (SMARA). The Act requires the State Geologist to classify mineral areas in the state and the State Mining and Geology Board to designate mineral deposits of regional or statewide significance. What is the "Classification and Designation" process and how is it working?

Jan 1, 1984