Search Documents

By Maurício L. Torem, Isabella A. Scorzelli

Taboca Mining is one of the largest producers of tin in the world. In its pilot plant, significant amounts of a middling of 90% xenotime (YPO4) and 10% zircon (ZrSi04) are produced. Until now, these minerals of this ore body could not be separated successfully. This paper presents some aspects of the fundamentals of xenotime and zircon flotation with anionic (fatty acids) and cationic (amine acetate) collector, as well as the influence of the superficial leaching of the minerals with cold HCI and HNO3 on the floatability. The mineralogical studies showed that both minerals are optically liberated in -212+106 µm size fraction. Surprisingly, SEM analysis indicated that both xenotime and zircon contain very small inclusions (1-5 µm) of thorite (ThSiO4). On the other hand, zircon is fairly metamictizated giving rise to malacon. Zeta potential tests showed that the isoelectric points of xenotime and zircon correspond to a pH value of 4.5 and 4.7, respectively.The pretreatment with HCI and HNO3 displaced the isoeletric point (IEP) of the minerals to the left. The microflotation tests indicated that the floatability of both untreated and treated minerals are quite similar in the presence of the collectors studied in this work. Adsorption mechanisms are also suggested.

Jan 1, 1995

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By J. Smolensky, M. Paul

The Nordhalde is a waste rock pile resulting from uranium mining near Ronneburg, Germany. The pile contains over 27 million m3 of waste rock. Typical seepage water has a pH of 2.7 and a sulfate concentration of 10,000 mg/L. Geochemical investigations of the Nordhalde from 1993 to 1996 included drillholes, test pits, ABA and metals analyses, column tests, and a detailed review of the construction history of the pile. In 1996, eight drillholes were instrumented for monitoring oxygen and temperature. Monitoring continued for a fill year. Hourly temperature and pressure readings were taken by automated data recorder. Oxygen concentrations were measured three times per week, and periodic gas samples were obtained for complete analysis. The resulting data set is believed to be one of the most comprehensive of its kind. Effects noted elsewhere, such as thermal convection, are evident. However, unlike other data in the literature, the NordhaIde data shows a strong seasonal effect, with convection dominating oxygen transport only in the winter months. Analysis of the data allowed the amount of contaminants associated with ongoing and historical oxidation to be compared, and results were used to assess the potential effectiveness of proposed remediation measures.

Jan 1, 2000

By P-M. Dupond, S. Lowrie, C. Tauziéde, Z. Pokryszka, A. D. Jones

A physical model has been developed to simulate the flows and mixing of gases in the waste of a longwall retreat coalface. The model is used in conjunction with computational modelling, and the distributions of permeability and gas emission in the model waste follow those in computer simulations (Pokryszka et al 1996). The physical model represents at 1170th scale a 200 m long, 3 m high coalface with a waste extending up to 280 m to the face start line. The model is tilted to the same seam slopes as the real face, e.g. 22° ascensional ventilation along the face and 7" slope to the dip. The purpose is to investigate the flow of three components: ventilation seepage flow through the waste; methane; and nitrogen injected to quell spontaneous combustion. A heavier-than-air surrogate gas (SF,) is used in place of methane, and therefore the model is inverted so that gas layers form along the 'roof". The main forces driving the flows in the waste (pressure gradients due to ventilation and the density difference of gas layers) are kept in proportion by appropriate scaling of the permeability. Calibration and validation used data from a coalface at a mine in the Lorraine coalfield. The model is now in operational use.

Jan 1, 1997

By William P. Diamond

Production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 m' to 10.1 x 106 m3. Peak production rates were generally about 0.03 to 0.06 x 106 &/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to several factors including: completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance, is hole location. Holes on the ends of the panels, where overburden strata are in tension due to the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location which is in compression. Analysis of gob gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1995

By William A. Kneller

Fifteen samples of chert from seven localities in Ohio were tested for potential durability and reactivity in concrete. The tests determined are porosity, pore-size distribution, relative degree crystallinity, specific surface area, and degree of dissolution according to the ASTM C289-71, Potential Reactivity of Aggregates, Chemical Methods. The results of these tests were compared with petrographic, electron optical, physical-chemical, and engineering properties of the chert samples. Based on these tests, the important properties that affect the durability and reactivity of chert in concrete were observed to be: (1) porosity, (2) pore-size distribution or pore spectra, (3) relative degree of crystallinity, (4) grain size, (5) specific surface area, (6) impurities, and (7) amount and species of quartz present-all of which are functions of original composition, time (geologic age), depth of burial, tectonics, and diagenesis. Preliminary results of this study indicated that the geologic history and physical-chemical properties of chert vary from one sample to another, and any one or combination of these parameters affect the performance of the chert in concrete. These complex interrelationships are difficult to ascertain; if the performance of the chert in concrete is to be predicted, it is necessary to study in detail this enigmatic material.

Jan 1, 1978

By Steven R. Wardwell, Gerald G. Stokes

INTRODUCTION A compaction grouting program to control ground loss, and to minimize surface settlement, was developed for the West Tunnel of the Phoenix Storm Drain Tunnels. The West Tunnel was 4,200 m long, 7.56 m in excavated diameter, and was excavated with shallow cover through the central Phoenix business district. The tunnel could not have been successfully excavated without the compaction grouting program. HISTORY After heated political debate over a ten year period, the Arizona Department of Transportation (ADOT) was granted approval to build the Papago Freeway, an extension of Interstate 10, through central Phoenix. To comply with environmental constraints, a portion of the Freeway was depressed, requiring an excavation 10 meters in depth, thus intersecting surface run-off from the northern section of Phoenix. This required that ADOT and Project Design Consultant, Howard, Needles, Tammen & Bergendoff (HNTB) design a drain system to collect run-off and transport it approximately 4 kilometers to the Salt River through the City of Phoenix. Tunnels were chosen for the main discharge conduits because depth and location of the system made cut and cover construction impractical. A contract for construction of the tunnels was awarded to Shank-Artukovich-Ohbayashi (S-A-O) on May 24, 1984.

Jan 1, 1987

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

Jan 1, 2006

Semiautogenous (SAG) ball mills are being increasingly used today for the coarse grinding of a range of ores, including gold, copper and iron. Larger mines are demanding mills with larger throughputs. This has led to some remarkable developments in mill diameters and installed powers. Conventional design principles - mills with trunnion bearings - have reached their limitations. This article describes one SAG mill with a slide-shoe arrangement and Krupp Polysius' Combiflex twin drive. In August 1997, the world's largest SAG mill with a slide-shoe arrangement was commissioned in Queensland, Australia, operating as a wet mill. The inside diameter is 10.4 x 5.1 m (34 x 17 ft) effective grinding length. The 1.36-ktlh (1,500-stph) SAG mill is driven by two Combiflex drives (twin drives with 2 x 5,500-MW or 7,375-hp installed motor power) in conjunction with a girth gear (outside diameter 11,890 mm or 468 in.). Commissioning of the SAG mill was completed with no notable technical difficulties. The plant runs continuously except for planned maintenance stoppages and process-specific reasons. As this article is written, the machine has been in operation for about 8,000 hours without major problems.

Jan 1, 1998

By Andreas G. Mueller

Gold-silver and copper-gold deposits with high-temperature wallrock alteration of Ca-Mg-Fe-Al silicates occur in ca. 3.0 Ga old greenstone belts of the Yilgarn Block, Western Australia. The deposits are hosted by amphibolite-facies komatiites, basalts and BIF, controlled by ductile shear zones and located within the contact-metamorphic aureoles of composite granodiorite-granite batholiths. Disseminated sulfides and free gold form foliation-parallel ore zones in a gangue of anhydrous silicates (garnet, clinopyroxene, olivine), hydrous silicates (amphibole, biotite) and calcite. The deposits may be classified on the basis of their dominant economic metals as: 1(1) Gold skarns with substantial silver as by-product, represented by the Marvel Loch mine (production: 2,200,000 t at 3.5 g/t Au), and characterized by the mineral association pyrrhotite, loellingite, arsenopyrite, galena, gold and magnetite. (2) Gold skarns with low silver contents, represented by the Nevoria mine (production:1,850,000 t at 3.4 g/t Au), and characterized by the mineral association pyrrhotite, chalcopyrite, arsenopyrite, gold, Bi-tellurides and magnetite. (3) Copper-gold skarns, represented by the Elverdton mine (production: 850,000 t at .7 5 Cu, 0.81 g/t Au), and characterized by the mineral association magnetite, chalcopyrite, pyrrhotite, pyrite, gold and Ag-Bi tellurides.

Jan 1, 1990

By J. Philip Bromberg

Any effectuation of a viable program of air pollution control will' require a basic understanding of the chemistry of atmospheric processes, the fate and migration of SO2, and the ultimate health effects of the sulfur oxides themselves. The migration and ultimate fate of Sop discharged into the atmosphere will be discussed with particular emphasis on the various conflicting views and how these relate to our present emission control regulations. Our present lack of knowledge is a severe detriment, and consideration will be given to those particular areas where future research may best be directed to provide the answers to a number of perplexing questions.

Jan 1, 1976

By Gordon Cook

American Electric Power Company (AEP operates 31 coal mines in three states, and some 26 electric generating stations (19 coal-fired) located in the Ohio River Basin. Normally the system burns over 36,071,600 tonnes (40,000,000 tons) of coal and generates in excess of 3.6 X 1018 J (100 billion kwh) of electricity per year. In 1975, AEP, in response to the progressively more stringent air quality requirements of the clean air act, acquired large low-sulfur reserves in Carbon County, Utah (Figure 1. Location Map). Price River Coal Company (PRCC) is the operator OF this multi-seam complex, which is part of the Book Cliffs coalfield at an elevation exceeding 1,829 m (6,000 ft.). The topography is mountainous and divided by numerous canyons. Flat areas are at a premium (Figure 2. Castle Gate Area). Modern high production longwall mining takes in some top and bottom waste, and in this particular operation, it amounts to about 14% of the ROM tonnage.

Jan 1, 1983

By F. Milton Lewis

Several alternatives are available for treating lover grade gold ores averaging 0.04 to 0.10 ounce per ton. These include heap, vat and agitation leaching and may involve conventional zinc precipitation or carbon adsorption-electrowinning systems. Each of these processes have their inherent economic and operating advantages and disadvantages and the selection of the optimum method for a given gold ore is solely based on economic evaluation of the applicable processes. In this paper an effort is made to provide engineering feasibility estimates for the above processes under varying operational conditions such as ore grade and price of gold.

Jan 1, 1974

By D J. Bradshaw

It is well known that the chemical environment determines the success of the flotation process, however its characterization and control is difficult to achieve. This work evaluates the use of various measurements, including mineral potential measurements, in gaining an understanding of the influence of varying parameters such as the milling media and the reagent suite composition on the flotation performance of a platinum group metal (PGM) bearing ore. The results showed differences in the response of the various mineral electrodes to the different conditions, however the changes in flotation performance of the different minerals in the ore could not be wholly described by the electrochemical changes, demonstrating the limitations of these measurements.

Jan 1, 1999

By D. M. Thayer

Laboratory and pilot plant investigations have indicated that copper recoveries of 50% can be achieved with fine grinding and flotation of a copper reverberatory furnace slag, Microscopic and microprobe studies indicate that the recoverable copper is in the form of matte, chalcocite, and metallic copper; the percentage of copper in particles appearing to be copper-free was from 0.23 - 0.54%.

Jan 1, 1969

By Charles J. Johnson

The United States is totally dependent on imports for all primary chromite and most ferrochrome supplies. Although the United States imports chromite and ferrochrome from a number of countries, the long-term future of chromite supplies appears to lie in southern Africa (Republic of South Africa and Zimbabwe) where 88 percent of known world reserves exist. Floreover, low mining costs and the availability of low-cost electricity for ferrochrome production gives South Africa a comparative advantage over most other chromite and ferrochrome-producing nations. A well-known problem faced by the United States is that when viewed from a longer-term perspective, the major sources of supply of metallurgical grade chromite and ferrochrome may be subject to disruption. The three countries that have caused the greatest concern have been the Republic of South Africa, the Soviet Union, and Zimbabwe. South Africa presents a particularly difficult problem because it may be subject to internal political unrest and/or U. N, economic sanctions. South Africa has increased its share of world chromium production from about 30 percent in 1968 to 62 percent in 1978.1

Jan 1, 1982

By R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in Carbon in Pulp and Carbon in Leach circuits has been investigated. Carbons from four U.S.A. mines, one Canadian mine and one South African mine were characterized before and after regeneration. The use of thermal gravimetric analyses demonstrated the presence of inorganic compounds on the surface of the carbon. Thermal regeneration was investigated using factorial' analysis to determine the effect or interaction of furnace temperature, retention time and the use of supplemental steam. The operation of acid leaching prior to or after gold elution was investigated. The effect of water quenching, regenerated carbon was also studied. From the data obtained in this investigation, guidelines are given for effective regeneration operation.

Jan 1, 1985

By Patrick Sullivan

Over the past few years, successful operations for processing phosphates employing the Grate-Kiln System have been achieved. Control and instrumentation philosophy followed in these installations are described and analyzed. Concepts utilizing digital techniques and computer systems appropriate for similar installations are also discussed.

Jan 1, 1967

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry - a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal increasingly emphasizes protection of the environment as well as economics of refuse handling. Coal companies are responding to the environmental control needs by devising new systems and adapting well-known techniques to refuse handling systems. Monterey Coal Company has operated a non-polluting refuse disposal system at its No. 1 Mine for over two years. The purpose of this paper is to describe the design considerations given to the planning of that system and the operational experience gained during its construction

Jan 1, 1973

By A. D. Pernichele

Four types of slope failures in waste dumps are recognized; debris flow, foundation failure, edge slump and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is considered to be the most dangerous because of its explosive mode of failure and lack of forewarning. The December failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicated that the impounded water was due to a zonal accumulation of Jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1971