Search Documents

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By Steven Hart, Graeme Hill

Boddington Gold Mine is situated 130km South-east of Perth, WA. The operation is managed by Worsley Alumina Pty Ltd. The Direct Leach plant was commissioned in mid 1986 at a rate of 3 million tonnes per annum. The plant was upgraded to 4.5 mtpa in 1988 and almost immediately to 6mtpa in 1989. Subsequent debottlenecking resulted in further increases in throughput up to 7mtpa by 1991. The SupergenelBasement Plant was constructed in 1990 and commissioned in early 1991. It was designed to process both copper-gold-silver anomalies within the laterite gold orebody and future hard rock ores. The Supergene plant incorporated control potential s­ulphidisation (CPS) and flotation ahead of CIL to remove a host of copper minerals. It operated in that configuration for 2 years at rates up to 350,000 tpa and average grades of 6.0 git gold and 1.2% copper. Gold recovery averaged 90.7% and copper recovery averaged 80.0% before the flotation circuit was decommissioned in March 1993. Quartz hosted high grade, free milling oxide and basement ores were discovered at the northern end of the orebody in 1990 and now comprise the major feed source to the basement plant. Oxide ores are currently milled at a rate of 550,000 tpa, while basement ores are milled at a 420,000 tpa rate. Metallurgical testwork during the feasibility stages indicated that up to 30% of gold in plant feed could be recovered by gravity separation methods. It was also highlighted that signifi­cant improvements in overall plant recovery and reduced operating costs would be achieved by maximising gravity gold recovery ahead of cyanidation. To achieve this, rec;iesign and upgrade of the gravity circuit was necessary.

Jan 1, 1995

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By R. H. Mozley

It is not my intention in this paper to review recent developments in the mineral processing industry which might fall under the above heading, but to refer to some of the research that I have done over the past 25 years or so. To begin with then, my student days at the Camborne School of Mines, the year 1952. Equipment from the last century was still in everyday use at the local tin mines. At South Crofty Ltd a steam beam engine 100 years old was pumping mine water from 2000 feet, the motive force being conveyed from surface to the pump at the bottom of the mine by a 14 inch square pitch pine rod joined with forged iron straps, steam winders were still in use, and in the mills, stamps ground the ore, and the cassiterite was recovered by equipment with exotic names like "buddies, kievs, and round frames." And to equip us students for the brave new world, we included in our practical mineral dressing a day's test programme with a Californian stamp -- experience that I am still waiting to put to good use!

Jan 1, 1984

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

By Brad Grothen

What is the most economical way of tunneling in mixed ground that may experience high pressures? Non-continuously pressurized, mixed ground Tunnel Boring Machines (TBMs) are being utilized to deal with a wide range of geology. Continuous improvements in these mixed ground machines allow for ever-increasing efficiency and reduction of project risk due to unexpected conditions. We will explore the performance of recent mixed ground machines throughout the world and then look at how new improvements to mixed ground machines will enable excavation of an expanded range of ground conditions. These conditions include mixed ground with low fines, mixed face rock, and fracture/fault zones with high pressures where in the past a Slurry TBM may have been utilized.

Dec 1, 2022

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By E. T. Pecina

Bioleaching is a viable option for the processing of auriargentiferous refractory ores with high arsenic content. The application of mesophilic (A. ferrooxidans and ?L. ferrooxidans?) and thermophilic bacteria of the genus Sulfolobus (S. solfataricus and S. acidocaldarius) as oxidant treatment before the cyanidation of an industrial arsenical pyrite concentrate is presented. The results show that extraction of gold and silver increases due to bio-oxidation caused by mesophilic bacteria and results in a maximum gold recovery of 68%. In all strains studied, biooxidation resulted in an average silver recovery of 50%. The results showed that all evaluated strains were sensitive to solids content (5 to 20%) and average particle size (75 and 38 µm) of the concentrate.

Jan 1, 2010

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By Andrew B. Allen, Charles W. Robinson, Robert L. Schneider

In April, the US Synthetic Fuels Corp. broke a three-year silence and made its first financial award by approving a $820,750 loan for the First Colony peat-to-methanol project in North Carolina (ME, May, page 403). Peat Methanol Associates (PMA), a partnership between Koppers Co., ETCO Methanol Inc., Transco, Peat Methanol Co., and l. B. Sunderland, broke ground at First Colony last year and plans to begin production in Dec. 1985. Although the award is only a small part of Synthetic Fuels Corp.'s $15-billion budget, it does signal the corporation's intention to move aggressively ahead. It also is a positive indication that First Colony will be completed and operated successfully. This article describes the methods and equipment that will be used to harvest peat at First Colony, as well as how the peat will be converted to methanol. Introduction Peat deposits found along North Carolina's coastal plain contain high-quality fuel-grade peat with an average heating value of more than 23.3 MJ/kg (10,000 Btu/lb) (dry), with a low sulfur and ash content. The deposits differ from other US peats in that they contain large, sound Atlantic White Cedar and Cypress logs, stumps, and roots that may extend throughout the full depth of the deposit. A second difference is that these deposits are much more highly decomposed and, in the raw state, have the appearance and feel of a heavy, reddish-brown grease. These factors make it impractical to use standard production equipment so a new line was developed. Also, because of these conditions, techniques were modified to facilitate production. First Colony Farms, located near Creswell, NC, developed and evaluated a milled peat program. Equipment for this production method was designed and built, production rates were established from field operations, drying rates were established, weather data were analyzed, and total operating and capital costs were estimated. The method depends on the sun and wind for drying peat to the desired moisture content, in this case around 40%. Therefore, field preparation is actually the construction of a large solar collector to dry the peat so it can be harvested and stockpiled. It is essential that this collector be properly profiled initially and maintained during production to prevent precipitation from ponding. Initial Field Preparation Initial field preparation includes cleaning existing canals and constructing ditches and water control structures for proper drainage of rainwater run-off, building adequate roads for site access, removing surface vegetation, and profiling and sloping the fields. At First Colony, the 60.7-km2 (15,000-acre) harvesting area was divided into 129.5-hm2 (320-acre) blocks about 1.6 km (1 mile) long and 805 m (0.5 mile) wide. This was accomplished by cleaning main outfall canals with adjacent roads built from canal spoil at 1.6-km (1-mile) intervals. Existing intermediate canals that feed into main outfall canals at 805-m (0.5-mile) intervals also are cleaned. Headland roads are constructed from canal spoil along each side of each intermediate canal. This 129.5-hm2 (320-acre) block is then divided into 32 harvest strips by small V-ditches constructed at 50-m (165-ft) intervals. At the end of the field with the lowest elevation, corrugated steel pipe culverts are installed under the headland road in each V-ditch to control rainwater runoff into intermediate canals. Runoff water from the fields is diverted to a holding pond to prevent any increase in peak water runoff rates and to allow for more uniform drainage rate than experienced to date. After the drainage system is installed, harvest strips are ready for grinding and sloping operations. Surface vegetation, made up of small, waxy-leafed shrubs such as Gallberry, Bayberry, Magnolia, and scattered pond pine, can be effectively ground and incorporated into the upper surface of the peat layer. Here, it will rapidly decompose and have little effect on overall peat quality, thus eliminating the standard practice of pushing the vegetation and upper wood layer into long windrows with bulldozers and hauling this debris from the fields. Incorporating vegetation into the upper surface is known as the initial 102-mm (4-in.) surface vegetation grind and is accomplished by using a modified Bros Rota Mixer. Following this operation, and by using the same unit, a sec¬ond grind with a depth of 200-255 mm (8-10 in.) is made. This reduces the debris to a finer consistency, mixes it with the upper peat layer, and grinds any wood found in the upper 200-255 mm (8-10 in.). After initial grinding operations are completed, the augering or sloping operations can be accomplished with little or no hin-

Jan 7, 1983

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By Gordon T. Clark

The preliminary design of four mined stations and 7.2 km (4.5 miles) of tunnels for Seattle’s light rail transit system is described. Constraints that influenced the design and options that were studied are discussed. The hilly post-glacial soft-ground geology of the Puget Sound Region pushed the alignment deep. Mined underground stations at depths up to 75 m (250 ft) and shafts with excavated diameters of 20-m (65-ft) are required. A 460 m (1,500 ft) sub-aqueous crossing of Portage Bay and undercrossing of an active 12-lane multi-level freeway were two of the more significant design constraints.

Jan 1, 2001

By Th. Petropulos

The Zn-Ag-Pb mineralization zone near Molai (Greece) was explored by more, than 60 drillholes. Promising results led to the decision of additional drillholes in order to confirm the expected spatial extension of the deposit. A multiobjective approach is described which optimizes the location of a set of 5 additional drillholes. The decision is based on estimation errors for grade, thickness and depth of the main ore bearing layer, with respect to cut-off values for grade and thickness. The linear combination of these variables defines a favorability index which is used for mapping optimal drillhole locations. The map shows several clusters of favorable cells. A declustrering algorithm is used to select a representative cell for drilling in each cluster.

Jan 1, 1989

Crushing and grinding The Crushing and Grinding Technical Committee There was substantial activity in the area of crushing and grinding with the improved outlook in the industry. The Crushing and Grinding Committee's theme of 1987's Annual Meeting in Denver was Fundamentals of Mechanical Design for Crushing and Grinding Mills. At the meeting, the concept of gearless sag mill variable speed drives was taken out of the closet, dusted off, and a wraparound motor was put on hard copy with the ordering of a 9.7- x 4.5-m, 8.2-MW (32- x 15-ft, 11,000-) sag mill. Additionally, comparisons were provided to the mill design of the gearless drive sag mill and the twin 4.5 MW (6000 hp) do variable speed drives placed on the drawing board for the Kennecott UCD Expansions. This involved a 10- x 4.5m, 8.9 MW (34- x 15 ft, 12,000 hp) sag mill. Differing opinions were also expressed in technical presentations pertaining to the need for quality mill specifications in design and manufacturing. J. Berney-Ficklin of Bechtel presented a paper outlining the need for quality design and manufacturing specifications in large scale grinding mills, and the overall cost reduction in capital and operating costs. Others presented differing specific views, but all emphasized a central theme. Quality and reliable designs in large mills should not be compromised. In-pit crushing applications continue to increase, overseas and in the US, in both mining and quarrying. Different in-pit crushing units have been classified as mobile, with integral transport systems; semi-mobile, typically modular systems that use separate transporters for repositioning; semi-stationary plants that must be dismantled before transporting and typically require earthwork and concrete foundation work; and stationary in-pit crushing plants, which remain in place for the life of the pit. The majority of equipment sales of conventional crushing and grinding circuits in 1987 were to gold mining operations. There have been two areas of end use: • conventional jaw/gyratory or impact crushing circuits preparing low grade ores for heap leaching; and • small scale sag/ball mill circuits preparing higher grade ores for classical cyanide leach/ recovery circuits. There was also continued interest in ABC and SABC circuits for both base and precious metals plants. High pressure roll crushers continue to attract considerable interest in the cement industry. There, they are used to prepare raw materials or clinker for subsequent ball/tube milling. However, they have apparently been less successful in the mineral industry where the energy savings/ capacity gains have been much less dramatic. Several papers covering the theory and application of these machines were presented in an industrial minerals session on cement at the SME Annual Meeting. The Third International Conference on Hydrocylones, held in England in October produced several papers of interest on classification and screening to the mining industry. In particular, a new cyclone apex, developed by Mt. Newman Mining, shows promise of reducing water flow to the cyclone underflow stream and, therefore, increased underflow pulp densities and reduced fines recycle in grinding circuits. A twin vortex hydrocyclone was also described and shown to give a sharper split than conventional units. Similar double cyclones were introduced in the 1950's, but failed to achieve widespread acceptance. This was due mainly to a proneness to blockage in the transitional zone. It will be interesting to see whether this latest variant can overcome this problem in the typical operation. A number of North American iron ore plants installed the capability to produce fluxed iron ore pellets. Most chose to grind the stone on site with circuits designed to grind taconite ore. Methods employed to grind this material included single-stage ball mills closed with fine screens, rod and ball mill circuits - both open and closed with cyclones - and semiautogenous mills, followed by ball mills closed with screens or cyclones. Dewatering and tailings disposal B.M. Moudgil and D.L. Sober, University of Florida Due to tightened environmental regulations and the need for more efficient land use, a greater interest in dewatering and waste disposal has developed. As a result, research efforts in flocculation, surface chemistry, and polymers science have focused on the problems related to the dewatering of solid mineral wastes. A few studies have been conducted to examine the flocculation process. Hogg et al., (1987) discussed the formation and growth of flocs. They determined the size and density of flocs was controlled by the physical conditions of the system (e.g. agitation,

Jan 5, 1988

By Jon C. Volkwein

The U. S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography at the Pittsburgh Research Center. These gas results were analyzed for explosibility. Personal exposure to carbon monoxide was also monitored. The highest methane level observed was 9.55 pct. The Inert gas levels, (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were non-explosive. The maximum personal time weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining. INTRODUCTION The auger highwall mining method is an effective method to recover coal from a reserve when removal of the overburden by surface mining equipment becomes uneconomical. In this method of mining, a horizontal auger enters the coal seam from the surface mine bench under the highwall and the coal is drilled in a series of parallel holes. Historically, coal mined from the surface is relatively shallow, and over time, methane associated with the coal has dissipated through the surface. In most circumstances, little methane has been found associated with auger mining. However, mining technology has enabled surface mining of deeper reserves of coal. Furthermore, environmental constraints have forced the highwall extraction method to be used to remove coal under wetlands, further increasing the chances of encountering methane. Recently incidents of methane explosions at a few auger mining operations have resulted in injuries and increased testing for methane at the collars of auger holes. The fuel source of the reported explosions was not necessarily limited to methane, but may also have involved coal dust. The Mine Safety and Health Administration (MSHA) met with the Bureau to discuss what technology might be available to enable the safe resumption of mining. The discussion included the difficulty of ventilating through the solid shafts of the augers, that steel bits probably created the ignition source, and that perhaps inerting the holes with low oxygen and high carbon dioxide concentrations from the machine's diesel exhaust was a potential solution. Considering the ventilation aspects of the problem, it was not clear If ventilation could be reliably established. If some degree of ventilation to the front of the mining head is achieved, it may combine with methane to bring the hole atmosphere from a rich, nonexplosive mixture to an explosive mixture. Furthermore, it may not prevent a dust explosion in such a mining configuration. Lack of access through the shafts of auger type mining machines further limits the ability to add water or air to cool bits to prevent an ignition source from developing. Either of these approaches would also be expensive. The process of mining coal In an inert atmosphere has been considered in the past, but to our knowledge, never implemented (Department of Interior, 1970). Clearly, implementation in underground mining would be more complicated. On a mine bench open to the atmosphere, however, adding inert gas to the mining head could provide a quick, feasible method to prevent explosions at auger highwall mining operations. Also the problem of how to move the inert gas to the cutting head of the machine had to be considered. Preventing explosions on auger mining machines using inert gas requires three primary considerations: first is the source of inert gas; second, placing the inert gas at the cutter head; and third, monitoring the hole atmosphere. Any gas source having an effective inert gas concentration of 34 volume pct or greater will prevent methane from Igniting (Zabetakis, 1965). Sources of inert gas considered for this application included liquid nitrogen, modified shipboard inert gas generators (for hydrocarbon shipping and transfer), jet turbine engine (Paczkowski, et. al., 1982), the auger's diesel engine and a gasoline engine. Operation cost, purchase cost and availability limited our testing to the diesel and gasoline engines. This work tested each engine, separately and combined. To ensure effectiveness, both company and enforcement personnel need to know how to monitor the condition of the inerted hole. Measurements at depth inside the hole are possible by remote sampling through rigid tubing, but this method is Impractical for routine monitoring. Continuous monitoring of the exhaust gas stream is an alternative. The U. S. Bureau of Mines evaluated an inert gas system at an auger mining operation at a surface mine near Owensboro, KY. Coal was mined from the Number 9 Coalbed in Henderson Co. KY. Tests were conducted in January and March of 1992.

Jan 1, 1993

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023

By D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming mineral. A polymeric depressant is then added to attach to this re-surfaced mineral. Nearly 200 flotation tests with a 11 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother-collector system, grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1994

By Jessica Elzea, Haydn Murray

The term bentonite was first proposed in 1898 by Knight, a year after he had named this clay taylorite, because taylorite had been previously used for another mineral. The name taylorite was after the Taylor ranch, the site of the first mine, near Rock River, WY, and the name bentonite is from the Benton Shale in which the clay was thought at that time to occur. The Benton Shale was, in turn, named after Fort Benton, MT, located more than 640 km miles north of Rock River. Early in the 20th century, several geologists recognized that bentonite, mainly in beds in Cretaceous and Tertiary rocks, originated from transported volcanic materials. This recognition led to definitions based on origin, the one most widely quoted and generally accepted by geologists is the following definition by Ross and Shannon (1926): "Bentonite is a rock composed essentially of a crystalline clay-like mineral formed by devitrification and the accompanying chemical alteration of a glassy igneous material, usually a tuff or volcanic ash; and it often contains variable proportions of accessory crystal grains that were originally phenocrysts in the volcanic glass. These are feldspar (commonly orthoclase and oligoclase), biotite, quartz, pyroxenes, zircon, and various other minerals typical of volcanic rocks. The characteristic clay-like mineral has a micaceous habit and facile cleavage, high birefringence and a texture inherited from volcanic tuff or ash, and it is usually the mineral montmorillonite, but less often beidellite." The difficulty in applying the foregoing definition to bentonite as an industrial mineral commodity is that it is based on origin and is restricted to an ash, tuff, or volcanic glass parent material. Therefore, deposits consisting of the clay minerals required by this definition, but having uncertain origin or parent materials, cannot properly be called bentonite. Furthermore, many deposits in the western United States and in other countries that have formed from rocks other than the types required by the definition are being mined and sold as bentonite. Perhaps the best definition of bentonite as an industrial mineral is one given by R.E. Grim in a plenary lecture at the International Clay Conference (AIPEA) at Madrid, Spain, June 27, 1972. According to this redefinition, which will be used in this chapter, bentonite is a clay consisting essentially of smectite minerals (montmorillonite group of some usages), regardless of origin or occurrence. This definition solves the problem of the difference between the geologic and industrial usages of the term and overcomes the difficulty in assigning a name to smectite clay that formed from igneous rock other than ash, tuff, or glass, or those of sedimentary or uncertain origin. However, bentonite, when used with this meaning is still a rock term (consisting of more than one mineral), and it will not be possible to distinguish it from fuller's earth in many instances. One way of classifying bentonite is based on its swelling capacities when wet or added to water. Bentonite having sodium (Na+) as either the dominant or as an abundant exchangeable ion typically has very high swelling capacities and forms gel-like masses when added to water. Bentonite in which exchangeable calcium (Ca++) is more abundant than other ions has much lower swelling capacities than sodium varieties. Some calcium types swell little more than common clay, and most crumble into granular masses in water. Intermediate calcium-sodium bentonites, the so called mixed types, tend to swell moderately and to form gels of lesser volumes than equal masses of the sodium type bentonite. Because of the general relationship of swelling and exchangeable ion characteristics bentonite is commonly divided into the high swelling or sodium, low swelling or calcium, and moderate swelling or intermediate types. The term sub-bentonite (Davis et a]., 1940) is used inconsistently in industry for the low or moderate swelling varieties. The authors believe the use of this term should be discouraged because of its implication of low quality or low value and the lack of a mineralogical or use basis for it. In the United States bentonite is also classified by geographic location and the uses for which it is sold. Inasmuch as most of the low swelling calcium type occurs in states bordering the Gulf of Mexico, this variety is commonly called Southern bentonite. The largest high swelling sodium bentonite deposits and the major producing districts are in Wyoming and adjacent states. Therefore, this bentonite is commonly called the Wyoming or Western type. Such terms as drilling mud bentonite, foundry bond bentonite, and taconite bond bentonite relating directly to use are applied in marketing. Other terms including high and low yield bentonite, high and low gel bentonite, and high and low strength bentonite are also used to distinguish different grades. The varied classifications notwithstanding, bentonite occurs in so many different varieties that some cannot logically be classified according to any of the foregoing groupings. One of these types is hectorite, which is a high swelling lithium-bearing variety of smectite occurring mainly in California and adjacent states. It is, therefore, not a Wyoming type, and it occurs even farther west than the so called western bentonites. Others are bentonites having magnesium (Mg++) or hydrogen (H+) as the most abundant or dominant exchangeable ion. These types are neither sodium nor calcium varieties, and apparently some are low swelling, whereas others have rather high swelling capacities. Still another type of bentonite, the so-called potassium type, K-bentonite, or metabentonite, occurs in Ordovician and other Pa-

Jan 1, 1994

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993