Search Documents

By A. L. Boerner

Off-highway tire costs represent a significant portion of the total mining costs in openpit, truck-shovel operations. To extend the lives of tires, the site-specific factors influencing tire life should be investigated Valuable data can be obtained by combining historical operational data captured by a mine dispatch system with detailed tire and maintenance histories. Assuming that failure counts satisfy a Poisson distribution, F-tests can be applied to determine significant deviations from desired or target counts. The methodology developed in this paper can be used to identify the haul routes and loading and dumping zones that have significantly higher incidences of tire failure. Corrective action can then be targeted at these zones by modifying the shovel or truck operator practices; changing the haul route maintenance and clean up practices; or altering the bench, ramp or waste dump design parameters. An example is given of the correlation of tire separation and tire impact failures with haul routes for a fleet of nine Caterpillar 793C trucks in operation at the Chuquicamata Mine in northern Chile. A high incidence of impact failures was observed for the ex pit ore crusher and for tires installed in the left outer rear position on the trucks. The latter was postulated to be due to a preference for drivers to execute right-hand turns prior to dumping. Recommendations were made to revise crusher and dump cleanup practices and investigate the feasibility of super-elevating the surface of dumping zones to reduce ground pressure on the left rear tires.

Jan 1, 2002

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By David Wilburn

Recycled materials are increasingly being used in road construction to supplement natural aggregate derived from crushed stone, sand, and gravel. An understanding of the amount of substitution that is taking place, its economics, and factors affecting the level of substitution is useful in estimating the potential for recycling and in assessing the total supply of aggregate. While U.S. consumption of recycled aggregates from crushed concrete is estimated to have increased 160 percent between 1994 and 1996; it comprised less than 5 percent of total aggregates consumed in 1995. Construction waste supply is regional, and is determined by infrastructure decay and replacement rates. Aggregate recycling rates are greater in urban areas where infrastructure is being replaced, natural aggregate resources are limited, disposal costs are high, or strict environmental regulations prevent disposal. Recycling is expected to increase as construction contractors attempt to save on transportation, disposal, and new material costs. Aggregate producers include recycled material as an option to consumers in order to prolong the life of their reserves and improve their range of products. Recycled aggregates can be a supplement for natural aggregates in selected applications, but their use should be evaluated locally based upon relative cost, quality, and market factors Because aggregate recycling is often affected by local and regional transportation systems, disposal and tipping fees, resource supply, the market for specific products, and municipal support, costs for three representative fixed site operations of different sizes were modeled. Under study conditions, all were found to be profitable, but highly dependent upon local tipping fees and market prices, which can differ significantly by location. Smaller operations were found to have different operational dynamics, often requiring creative marketing or incentives to maintain profitability.

Jan 1, 2001

By David B. Campbell

INTRODUCTION This submission was made to the Royal Commission of Inquiry into uranium mining in British Columbia. It discusses the stability of waste rock piles that might be developed in conjunction with uranium mining and the control of leachates that might be generated within these waste rock piles over the short and the long term. Short term refers to the interval during which a waste rock pile undergoes either continuous, or alternatively intermittent development, and in general can be considered to extend over the operating life of the mine. Long term refers to the postmining period, i.e. after the ore-body has been exhausted, and mining operations have ceased. Two major classes of waste material are generated in the course of mining and milling operations. Tails, which are the solid waste materials produced by the milling operations commonly exit the mill in slurry form and are stored in tailing retention ponds. Management and control of these slurried wastes are the subject of other papers to the Commission and this conference. In the course of the mining operations, it may be necessary to remove rock materials that are below cut-off grade. That is, ore concentrations within some of the mined rock may be lower than the concentrations which on the basis of economic considerations justifies milling the material. Rock which is removed in the course of the mining operations, but which is below cut-off grade is referred to as waste rock. This waste rock is commonly consigned to a specific area for disposal where it is placed in a mound or pile, i.e. a waste rock pile. Ore concentrations within the waste rock may vary from zero to just below cut-off grade. Since an increase in the market value of uranium could at some time in future result in reduction of the cut-off grade, it follows that waste rock containing ore concentrations slightly below today's cut-off grade could become ore grade rock at some time in future. For this reason, the mine operators may deem it advisable to separate waste rock according to grade, and to consign the waste rock to two or more individual waste rock piles. For purposes of clarity and simplicity, this submission treats the stability of waste rock piles and leachate control in a manner which assumes that these potential problems are isolated and separate from other aspects of the mining and milling operations. For many site specific cases, the problem of potential leachate control might be integrated with the tailings management aspect of the project, thereby realizing economic benefits while at the same time reducing the potential for adverse environmental impact.

Jan 1, 1980

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By Ronald E. Yarbrough, Theodore L. Triplett, Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from a high-extraction retreat room-and-pillar operation in southern Illinois. The objective of this monitoring program is to study the inter- action between the ground surface and a structure during a subsidence event. Data from such a study should enhance the understanding of the mechanisms that produce structural damage and aid in the design of structures that resist such damage. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tiltmeter to detect and follow the tilt of the foundations caused by the mining subsidence sequence is demonstrated. Using data from this tiltmeter, the development of curvature in the foundations as they conformed to the displaced ground surface is shown. This curvature is rep- resented by differences in tilt at various points on the foundations, indicating a change in tilt over a horizontal distance. Also, even though subsidence damage has not been fully analyzed, preliminary observations of the cracks that formed in the foundations are reported. These cracks resulted in the separation of one footing into distinct pieces; therefore, their effect on the tilt readings is cited.

Jan 1, 1986

By A. Adhikari, P. Tukkaraja, S. Jayaraman Sridharan

Shafts are critical components of the mine ventilation systems and contribute significantly to the mine ventilation pressure. Estimation of shaft pressure losses is an important aspect of mine ventilation planning and shaft frictional pressure losses are extensively studies. Shock losses contributed by shaft buntons are estimated using the interference factor model developed half a century ago. This study aims to develop a better performing prediction model for shaft buntons using state of the art experiment and numerical data, and machine learning techniques. Results show that the present prediction model is performing poorly, and the prediction performance can be improved by incorporating additional predictor variables. The Artificial Neural Network standardized Machine Learning model developed in this study is able to predict the shaft bunton shock loss with high accuracy (R2 = 0.956).

Jun 25, 2023

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By Walter C. Jr. Sherman

6.1-SOIL MECHANICS WALTER C. SHERMAN, JR. 6.1.1-DEFINITION Soil mechanics is concerned with the behavior of soils in relation to the design, construction and performance of engineering works. In this context, soils include all uncemented materials, such as, gravels, sands, silts and clays, either naturally or artificially deposited, and, under certain conditions, weakly cemented, badly broken or weathered rocks. Many types of mine wastes have physical properties similar to those of soils and thus are amenable to analysis by the principles of soil mechanics. The principles of soil mechanics are used to solve such problems as the stability of various types of structures with respect to failure of the supporting soils, determination of soil pressures and deformations in the design of foundations and retaining structures, analyses of seepage and under seepage, and stability with respect to sliding of excavated and natural slopes and embankments. 6.1.2--SOIL PROPERTIES Soils are classified on the basis of index properties, such as, particle-size distribution and plasticity characteristics. The Unified Soil Classification System1 used to classify soils for engineering purposes is shown in Table 6-1. Other physical properties important from an engineering standpoint include natural water content, density, permeability, shear strength and compressibility. Physical properties are evaluated on the basis of carefully conducted laboratory tests. Procedures for laboratory testing are presented by Lambe. 2 Soils, either of natural or artificial deposition, are complex three-phase materials consisting of solids, water and gas (usually air or water vapor). One of the most important principles in soil mechanics is based on the concept of effective stress in the soil-water system. A stress, a, applied to a saturated soil is taken partly by the soil particles (effective stress, a'), and partly by the water in the voids (neutral stress or pore water pressure, u,) so that a' = a - u,. Only the effective stress affects the mobilization of frictional resistance between soil particles. In partially saturated soils, the pore-water pressure is negative due to capillary effects. The effective stress relation remains valid for small negative pore pressures, but anomolies arise if the soil is significantly unsaturated. In this case, the pore pressure is commonly assumed as equal to the pore air pressure, u,, so that [ u' = u - u..] 6.1.3--SOIL EXPLORATIONS Soil explorations are carried out by borings or test pits. Hvorslev3 has reviewed procedures and boring requirements, such as, type, depth and spacing employed. In general, soil strata are logged and representative exploratory samples are recovered for classification purposes and for determining the subsurface soil profile, which is constructed utilizing also knowledge of the geology of a site. Undisturbed samples are recovered if the properties of the undisturbed soil are required, as generally is the case. The undisturbed soil sampler consists of a thin-wall tube

Jan 1, 1973

By K. H. Nimerick

A unique freeze conditioning agent (FCA) which functions by forming structurally weak ice rather than suppressing the freezing point of water has been successful in alleviating frozen coal problems. Frozen coal treated with FCA has been quickly unloaded at temperatures below -17.SoC (O°F). Other areas where FCA has found utility has been de-icing conveyor belts, idler, idler arms and other moving parts that have been impeded by ice.

Jan 1, 1977

By Robert H. Carpenter

Downstream dispersion curves for certain trace metals were obtained from two mineralized areas in the southeastern U. S. In Lincoln Co., Georgia, 7 sample sets were collected downstream from the Magruder mine, a polymetallic sulfide deposit (Zn-Cu-Pb-Ag-Au) in metavolcanic rocks. Five sample sets were collected along Joe Mill Creek in Grainger Go., Tennessee, downstream from a zone of zinc mineralization in carbonate rocks (Mississippi Valley-type). In both areas, analyses were made of Fe-Mn oxide coatings on lithic fragments and quartz pebbles, and the -80 mesh fraction of the stream sediment. A comparison of the dispersion curves reveals the following: 1.) the anomaly/background ratio is markedly higher in the Fe-Mn oxide coatings for zinc and copper; 2.) the anomaly/background ratlo is markedly higher in the -80 mesh fraction for lead which is not concentrated in the coatings; and, 3.) the Zn/Mn and Cu/Mn ratios in the coatings are useful in that they enhance downstream derectability of mineralization as well as provide for a simpler analytical procedure. There are several potential advantages of using coatings vs. the conventional -80 mesh fraction in stream sediment surveys. Because soluble metal is brought into the stream mainly in groundwater, deeper anomaly sources may be detectable from the oxide coatings than from clastic fractions of alluvium where much of the metal is derived from erosion of soils. Variability due to sampling may also be reduced, providing better discrimination of anomalies. In areas of glacial or alluvial cover, coating surveys may be particularly applicable.

Jan 1, 1975

By Luis R. Bittencourt

Research efforts have been made to characterize a refractory Brazilian bauxite ore composed basically of gibbsite, kaolinite and quartz. Detailed polished-section microprobe analysis of the unbroken ore has been used to describe the liberation characteristics and the association between mineral phases. The linear grade distributions for selected particle size fractions were determined by means? of a particular implementation of King's Random Fracture Model that uses the exponential model for the distribution of linear intercepts through both dispersed (kaolinite) and continuous (gibbsite) phases. The corresponding volumetric grade distributions were then determined by means of a constrained optimization technique for the solution of the transformation equation. Batch flotation experiments were carried out to determine the kinetics for particles of different sizes and the results correlated with the liberation spectrum for each size class.

Jan 1, 1991

By G. R. Green

The centre of the mining operations of the International Nickel Company, Ontario Division is Sudbury, a city of 160,000 population located 240 miles northwest of Toronto (Fig. 1). Within thirty miles of this city and located around the rim of the geological formation known as the Sudbury Basin are the ten underground mines and one open pit operated by the Company (Fig. 2). There are also four developing mines, three in the Sudbury area and one at Shebandowan, near the city of Thunder Bay, Ontario and approximately 150 miles north east of Duluth, Minnesota. In 1971 the mines produced 22,800,000 tons, 20,600,000 tons from underground and the balance from open pits. Also located in the Sudbury District are facilities to extract and refine the metals contained in the ore. There is a nickel refinery located at Port Colborne on Lake Erie. An additional nickel refinery is under construction near Sudbury. Fifteen elements are recovered from the Sudbury ores, nickel, copper, iron, sulphur, gold, silver, cobalt, tellurium and the six platinum group metals, platinum, palladium, iridium, rhodium, ruthenium and osmium. In 1966 a major expansion program was undertaken to meet increasing market requirements. Coinciding as it did with a severe

Jan 1, 1972

By Preston McGrain

Geologic maps are indispensable tools in the modern search for mineral and fossil-fuel resources. They are the first essential step in understanding the lithologic nature and structure of rock units that form the land surface and that lie beneath it. They provide the basic foundation for planning mineral resource exploration programs and form the superstructure from which subsurface investigations are projected. In view of the economic application of such maps, the Commonwealth of Kentucky and the Federal Government entered a formal agreement in 1960 to map Kentucky geologically on a scale of 1:24, 000, or one inch map distance equals 2,000 feet on the ground. A 7. 5-minute quadrangle would comprise the unit map area. A resolution which urged the preparation of a new geological map of the entire State was passed by the Kentucky Society of Professional Engineers in February 1959, and was presented to the Governor of Kentucky, the Legislative Research Commission, Kentucky Department of Economic Development (now Department of Commerce), Kentucky Chamber of Commerce, and Kentucky Geological Survey with a request for support and action. The request was subsequently endorsed and actively supported by numerous civic and professional societies as well as representatives of various facets of Kentucky government, commerce, and industry. Monies to initiate the program were appropriated by the next session of Kentucky legislature; this appropriation was matched by federal funds (Hagan, 1961). Kentucky's state-wide topographic mapping project was completed in 1956, just four years prior to starting the geologic mapping program. The recently completed modern 7. 5-minute, 1:24,000 topographic maps made ideal bases for plotting areal geology. Had they not been available, it is doubtful if a geo- logic mapping program so large and comprehensive could have been undertaken.

Jan 1, 1966

By Ed Schodowski

Wireless technology is a hot topic for anyone involved in the design, operation, maintenance or upgrading of mines or mineral processing plants because wireless technologies overcome barriers that have prevented many useful data inputs. Wireless communications can contribute to worker safety, satisfy environmental concerns, support plant security, track human and physical assets, and improve equipment maintenance. The cost structure of wireless is compelling and users can realize savings ? up to 90 percent less installed cost than wired instruments ? since wireless technology eliminates the need for expenses associated with cabling, engineering, construction and documentation. Many applications previously considered too expensive have become economically feasible with wireless. Two examples are continuous monitoring of safety showers to notify operators when one has been activated, and monitoring effluents to ensure environmental regulations are being met. In many cases, wireless transmitters can be installed where wired devices were too expensive to justify, or were not feasible due to physical or technical barriers. Examples include monitoring temperature measurements inside a rotating reactor or monitoring process variables in a tough, corrosive environment too challenging for a wired solution. Wireless also gives operating personnel mobility with the ability to communicate from remote or hard-to-reach zones. According to a recent Venture Development Corp. survey covering radio frequency (RF) of microwave industrial monitoring and control products, these features are contributing to the expected nationwide growth rate for industrial wireless applications of 19 percent annually from 2007 to 2012 (Taylor, 2008). At the same time, mineral producers have many questions about wireless systems including their applicability, reliability and security in this industry. Just what can wireless do? Is it secure and reliable? Can these instruments stand up to the rigors of the industry? Can wire-less technology provide the flexibility needed for mining applications?

Jan 1, 2009

By Derek J. McCracken, William G. Holroyd

Emery is a rock that at one time held a large share of the abrasives market. The introduction of synthetic abrasives, however has forced it to settle for only certain niches in the marketplace. This loss of market share is due mainly to the higher amounts of impurities and weaker internal structure that naturally occurring minerals have compared to manmade materials. The use of rocks and minerals as abrasives dates back to early man, who used flint, quartz, and other natural materials to fabricate various tools. During the 19th century, with the Industrial Revolution imminent, the character of the abrasives industry was changed forever as synthetics were introduced. Frank B. Norton is credited with producing the first manmade abrasive when, in 1855, he manufactured a vitrified grinding wheel using emery grit and clay. Before Norton's accomplishment emery had been the only commercially available abrasive. The latter part of the 20th century has seen synthetics capture an increasing share of the abrasives market from natural materials. The term emery is believed to have been derived from the words emeri (French), smeriglio (Italian), and smiris (Greek). The term corundum, for the principal mineral of emery, seems to have originated from kauruntaka, the Indian name for the mineral. GEOLOGY Emery is a gray to black, granular rock comprised of various minerals including corundum (A1,0,), an iron-bearing mineral (usually magnetite-Fe,O,, hematite-Fe,O,, or hercynite- FeAI,O,), and several trace impurities such as mullite, titania, silica, and magnesia. The hardness of emery normally ranges between 7 and 9 on the Mohs scale, depending on its mineral com- position and level of impurities. Corundum, the hardest mineral in emery, typically has a hardness of 9. The specific gravity of emery ranges from 3.2 to 4.5, also depending on mineral composition and purity. The crystallography of each mineral contained in emery differs somewhat. Corundum exhibits an hexagonal crystal structure, whereas magnetite forms within the isometric system, frequently as octahedral crystals. Hercynite, an iron spinel, is also isometric. Hematite has an hexagonal structure but often is found as botryoidal and reniform masses. Principal deposits of commerical emery are found in the United States, Turkey, and Greece. In the United States two emery producers in the Westchester County-Peekskill area and one in the Cortlandt County area of New York closed their mines in the late 1980s. Commercial production in the United States now comes only from the western Cascade Range in Oregon. The emery in New York has a typical A1,0, content of 41.5%. Most of the rock is not true emery because it contains a mixture of spinel and magnetite but very little corundum. The deposits are of Late Ordovician-Early Silurian age and consist of veins in which emery is mixed with olivine, pyroxene, and hornblende. The veins evidently were formed by contact metamorphism and are surrounded by Precambrian schists that contain mica, sillimanite, cordierite, garnet, and quartz. The deposits in Oregon were formed during Miocene time by the contact metamorphism of ferrunginous bauxite by intrusive lamprophyric dikes and plugs. Emery is found in thin layers bordering these tabular dikes, which are usually oriented perpendicular to bedding, and in "surficial placer deposits. The emery deposits in Turkey occur as small, massive, lens- shaped bodies and as surficial placers. They are believed to have formed during Permian and Triassic times. In Greece the principal site of emery production is at Cape Emeri on the Island of Naxos. These deposits consist of lenticular masses of emery surrounded by marble. They originated during Mesozoic time, evidently by metasomatic replacement. Smaller deposits on several other Aegean islands were formed by the metamorphism of bauxite or other alumina-rich materials.

Jan 1, 1994

At present the feasibility of developing underground facilities for the storage of a number of products including toxic waste, oil, nuclear waste and low pressure gas is under investigation in e number of countries. A possible method of storage is in large excavations, Preliminary ventilation design work has identified that the climatic conditions encountered within these large excavations are a limiting ventilation pollutant within the ventilation system. This paper examines the design of a variety of sizes of excavation from a ventilation viewpoint. The main phases of an excavations lifetime can be divided into four main phases, these being construction, civil and mechanical fitting, storage, full and sealed. The paper details ventilation design options for the first two phases of e vaults lifetime, giving climatic simulations to assess the likely climatic conditions within the excavations for e number of facility depths. The options for climatic control are given and analyzed by means of climatic simulations techniques. l. INTRODUCTION The feasibility of developing underground facilities for the storage of a number of products is under investigation at present in a number of countries. This paper details a possible design for such a facility where the product is to be stored in large underground excavations. A facility layout has been designed with the aim of allowing concurrent construction and storage operations. Thus from a ventilation perspective the facility consists of two circuits , a construction ventilation circuit and a product ventilation circuit both of which are served by an intake and a return surface connection The construction and storage circuits are considered as independent of each other , any interaction in the form of leakage must be from the construction to the storage circuit. From the facility design a ventilation network was developed to assess the ventilation requirements of the facility. In analyzing the pollutant loads for the construction circuit two pollutants were recognised to be critical to the ventilation design , these being diesel exhaust fumes and heat end humidity. In this paper ventilation design options for the construction and civil and mechanical fitting phases of the excavations are analyzed by means of climatic simulation and options for climatic control within the vaults are outlined . 2. FACILITY DESIGN A schematic diagram of a facility design is illustrated in Figure 1. There would be two distinct ventilation circuits , one to service the construction operations and the second to serve the storage operations which occur concurrently with construction , the circuits are separated by ventilation bulkheads . Access to the facility for intake air is provided by two drifts, one to serve each circuit. Two shafts act as returns to surface. The facility consists of two distinct zones for the storage of two types of product. One type is to be stored in smell linear excavations. The second zone is for the storage of a second product in larger excavations. The maximum cross-sectional area and perimeter for the smell linear excavations are 456.25 m2 and 83.2 m, while for the larger excavations they are 440.1 m2 and 86.4 m. Excavation construction consists of three phases: 1. Initial pilot tunnel development between main intake and return to provide through flow ventilation. 2. Enlargement to produce the required finished cross-section. 3. Civil and mechanical engineering work to fit out the excavation ready for storage. It is proposed to excavate the excavations using drill and blest methods utilising diesel equipment. Spoil is to be transported to surface by a conveyor belt system. At any one time the maximum number of working places requiring ventilation will consist of ; 3 storage sites, 2 excavations under construction, 2 excavations undergoing civil and mechanical fitting. [ ]

Jan 1, 1993

By Robert Marks, Enrico Dal Negro, Richard Schulkins

"In July 2012 construction started on the Grosvenor project, a five million tonne per annum underground longwall mine planned for Moranbah in Central Queensland. Grosvenor is located immediately to the south of the existing Moranbah North mine which has been in operation since 1998. EPBM technology is being used for the first time in Australia for excavation of a coal drift. The TBM was used to build two drifts on the project, one for the coal conveyor which will transport to surface, and another for people and equipment to access the underground once the mine’s operational (as shown in figure 1). The TBM will pass beneath a steel archway roof that has been installed at the drift’s entrance and begin drilling into the ground to build the seven metre diameter tunnel, descending at an angle of one in eight until it reaches the depth of the coal seam approximately 160 metres below.INTRODUCTION AND BACKGROUND The first TBM used in a coal mine was in 1962, a Wohlmyer, in Westerholt, Germany. A further 75 km of tunnels were excavated in coalmines within Germany between 1971 to 1983. This paper will review the Grosvenor Mine project (Grosvenor) owned by Anglo American Metallurgical Coal (Met Coal) includes the construction of a new underground coal mine and surface facilities on the northern boundary of the town of Moranbah in the Central Queensland Bowen Basin coal precinct. The contract to undertake the underground development works was awarded to Redpath in 2012. The scope of the Grosvenor Project was to construct temporary office and workshop facilities, install 2 portal arches, backfill boxcuts and infrastructure, excavate by EPBM method 967 m of 1:6 gradient Conveyor Drift and 1,258 m of 1:8 gradient Transport Drift, development of 2,520 m of pit bottom area roadways and development of 10,550 m of the first longwall tailgate. In the following figures 2 and 3, is possible to see the aerial view of the job-site."

Jan 1, 2016

By L. Alan Weakly

The Powder River Basin of northeastern Wyoming and southcentral Montana contains the largest strip minable reserve of compliance coal (0.27 kg or 0.6 or less Ibs of sulfur per million Btu) in the United States. In mining parlance, it is the mother lode. Wyoming's portion of the Basin is called the Southern Powder River Basin (SPRB). It has been the nation's top coal producer for the past nine years. And based on 1997 production statistics and estimated strippable compliance coal reserves, Wyoming should remain the nation's top producer for the next 51 plus years. In August 1994, ME featured 10 articles that covered all aspects of coal production in the SPRB. In this issue, five authors update the 1994 articles and provide a pre- diction of what the Basin will look like at the turn of the century. In addition to this article, the titles and authors of the other five articles include: ? "Geology of Wyoming's Powder River Basin coal field," by Gary B. Glass and Robert M. Lyman. ? "Coal quality challenges in the Powder River Basin," by Sharon Roness, Richard A. Turpin and Robert A. Young. ? "Markets for Southern Powder River Basin coal," by , Patti J. Best and Patrick W. Wright. ? "Evolution of mining equipment in the Powder River Basin," by Kenneth R. Miller and James L. Long. ? "Hauling coal into the 21st century," by Dave Willis and Will Cunningham.

Jan 1, 1998

By Dean H. Herrick

The production of crushed stone in the United States has exceeded 1.0 Gtpy since 1987. Eighty percent of the crushed stone produced is used in the aggregate industry, accounting for over half of the quantity of natural aggregate consumed in the United States. Approximately 718 of the crushed stone produced in 1989 was limestone and dolomite followed by granite, traprock, sandstone and quartzite, miscellaneous stone, marble, shell, calcareous marl, volcanic cinder and scoria, and slate in order of descending volume (Table 1). Of the remaining 20% crushed stone produced in the United States and not used as aggregate, 12% is used in the manufacture of cement which is an important construction material. Only 8% of crushed stone is used in specialty products not associated with the construction industry. Therefore, this chapter will concentrate on crushed stone as used in aggregates, with occasional reference to other uses or to chapters which discuss specific nonconstruction uses of crushed stone. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass by the addition of cementing or binding materials that produce a concrete by compaction, or by natural weight to produce a road or foundation fill. Aggregates are usually from 80 to 100% of the material volume of the construction masses in which they are used. Conditions necessary for a rock deposit to be developed for construction crushed stone include: Quality-should pass rigid specifications for strength and durability; Quantity-adequate volume of rock is needed to have a production life of at least 10 years, preferably 20 or more years; Market-must have adequate market to support a new crushed stone operation; Transportation-transportation cost must be competitive for the intended market; Environmental-the impacts of mining, processing and transportation of crushed stone on the environment at or surrounding the mine site must be within acceptable limits; Permitability-mining, processing and transportation of crushed stone must usually be permitted by governing agency. The following discussion will touch upon all facets of crushed stone operations from the mineral deposit and its geology to technology, uses, economic factors and end with governmental regulations of mining crushed stone. The sections are not designed to answer all questions, but rather to be an introduction to the crushed stone industry. Where more information is required, The Aggregate Handbook by Barksdale (1991) is recommended as the best general source.

Jan 1, 1994