Search Documents

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels1. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m(26.5 ft) above the miner’s head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roofbeam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999

By H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of handling bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at approximately the same speed and with minimum impact, then most of all belt conveyor problems disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. This paper will establish and discuss some general design criteria required for proper loading and transfer of materials from one conveyor to another. Specific attention is given to loading points, chutes, skirt board length and general design of transfer structures.

Jan 1, 1971

By Roger Malmström, H. Heden, Kjell Lidin

INTRODUCTION LKAB was formed at the turn of the century when the railways between the ore fields and harbors were built. The mines are situated north of the Arctic Circle in Sweden. Kiirunavaara is the largest mine, with a pro¬duction capacity of approximately 30 Mt/a. Malm¬berget has a capacity of about 12 Mt/ a. Both are under¬ground mines. Svappavaara, the only opencast mine currently in operation, has a capacity of about 4.5 Mt/a. The ore harbors are at Narvik for the Kiruna and Svappavaara mines and at Lulea for the Malmberget mine (see Fig. 1). Production in the form of finished products is shown in Fig. 2a, b, c, and d. Due to poor ore markets in re¬cent years, production and shipments have been cut back, but there was a positive swing in 1978. LKAB has been 96% state-owned since 1957. In addition to the iron mines in northern Sweden, LKAB has subsidiaries in central Sweden which produce sulfide ores, quartz sand, and uranium (Fig. 3). The mining methods employed are opencast bench stoping at Svappavaara and sublevel caving at Kiirunavaara and Malmberget. GEOLOGY The Kiirunavaara ore body is 4000 m long and av¬erages about 90 m wide, with variations in width from a few meters to around 150 m. The ore has been ex¬plored by deep drilling down to about 1000 m, but mag¬netic measurements indicate a depth of at least 1500 m. The Kiirunavaara ore is oriented in a north-northeasterly direction with a number of ores in the boundaries be¬tween the wall rock types. The ore in Kiirunavaara is mainly a fine-grained magnetite with a varying content of fine-grained apatite. The apatite content of the ore decreases with increasing depth. The other ores are all apatite-bearing and a couple are hematite ores (Fig. 4a, b). The ores are sedimentary, tilted, and tectonically de¬formed. They have a lateral dip of 0.87 to 1.2 rad (50 to 70°). The contacts between ore and wall rock are distinct and sharp, but both the hanging wall and the footwall are brecciated and impregnated with magnetite. The footwall of the Kiirunavaara ore consists of syenite porphyry with a low quartz content and rela¬tively good strength; the hanging wall consists of quartz porphyry. Both types are known as Kiruna porphyries. The ore at the boundary with the hanging wall is often rich in kaolin. There are a few veins of syenite porphyry running through the ore, which has a few major faults (Fig. 4c, d). There are two sharply delineated ore grades in Kiirunavaara: low phosphorus ore with less than 0.1 % phosphorus (about one-third of the ore) and high phos¬phorus ore with greater than 0.5% phosphorus. The iron content is 67% in the low phosphorus ore and 60% in the high phosphorus ore. These ore types are sold as different grades and so are kept separate during mining. MINING AT KIIRUNAVAARA The Kiirunavaara and Luossavaara ores were first mined using opencast bench stoping in 1902. When mining costs rose owing to higher waste removal, under¬ground methods were adopted. In the mid-1950s, the ores were still being mined on the surface at the same

Jan 1, 1982

By J. Castaneda, J. Schmidt

"INTRODUCTION Chino is an open-pit copper mining complex faced with intricate material routing requirements. Historically, this was challenging at the mine, in part because the shovel dig plan, haul plan, and dump plan were prepared completely separately. The mine now uses an integrated workflow for faster evaluation of schedules, which facilitates preparing balanced cutoff grade-to-equipment requirements, supports better mineral production, and improves schedule viability, while considering operational implications. Located in the state of New Mexico, Chino is one of nine Freeport-McMoRan mining operations in North America. This presentation discusses the benefits of implementing an integrated approach to tactical mine planning, and shares practical examples that were learned as Chino implemented an integrated tactical planning method. This includes improvements in completion time for preparing a schedule, minimal risk from manipulating Excel macros, data integration required to make short-term planning decisions, and better understanding of the mine plan’s effect in relation to the business’s key performance indicators. Ultimately, the integrated approach to tactical mine planning at Chino has led to production forecasts which are more achievable and reduced planning and execution variance. PROJECT OVERVIEW Chino mine is a porphyry copper deposit wholly owned by Freeport-McMoRan, the largest publicly traded copper producer in the world. Chino mine is located in Grant County, New Mexico, a short distance east of Silver City. Ore material mined from the pit today includes oxides, primary sulfides, and secondary sulfides. The mineralized material is sent to a mill, with a rated throughput of 42,000 tons per day, or to ROM leach pads with variable dumping capacities. At Chino, the short-range objective is to maximize total copper pounds sent to the mill, but no fixed cutoff grade accomplishes this for all periods. Instead, 12 different material classifications, including four sulfide classes that can feed either the mill or other destinations, and 38 cutoff bins, are aligned with the needs from operations, leaching, and the concentrator to create a schedule. Cutoffs vary from one week to another to cope with a highly intermittent ore body."

Jan 1, 2018

By Emily Wortman-Wunder

As the 2011 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2011 issue of the Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 330. A significant portion of the contribution that we as a professional society make is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2011 Transactions is the second Transactions to take advantage of new publication technologies. It appears solely in electronic format. The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which will better serve the mining community. Based on the feedback from the 2010 Transactions in e-book format, I believe that the transition to the all-digital format was the proper decision. The 2011 Transactions contain some of the most interesting research from the past year, including a 10-year profile of roof and rib fall trends from the National Institute of Occupational Safety and Health (NIOSH) and a new cross-disciplinary application of the tools of epidemiology to assess and mitigate risk in coal mines . This 2011 Transactions comprise of a total of 82 technical papers (626 pages including index), including all 19 papers published in 2011 in the Technical Papers Section of Mining Engineering magazine (Vol. 63) and all 32 papers published in 2011 in Minerals & Metallurgical Processing (Vol. 28). Additionally, this volume contains 31 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 82 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2011 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2011

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

By E. C. Skinner

As the program says -we'll he talking about the expectations of the Management of an Industrial Mineral enterprise relative to the activities of geologists engaged in that enterprise. Industrial Minerals is such a large industry both in tons produced and in value of product -and of such diversity and complexity of participating enterprises, minerals and products that I doubt if anyone person can speak for the entire industry as to the expectations of management with respect to the geologist. I'm sure there are major differences in emphasis between segments of management as to the relative importance of the different aspects of the geologists' role in the scheme of things. However, we will try to generalize concerning what we consider to be important factors and to be more specific perhaps of some of the factors with which we have had direct assessable experience.

Jan 1, 1972

By P. M. Soupios

The study of soft soil (wastes above the rock bed) an issue of great importance in civil engineering, is usually addressed by drilling boreholes. This method is rather expensive and time-consuming and although the information obtained is usually accurate, on the other hand it is much localized. Recently published researches have demonstrated the ability of the combination of geophysical exploration methods to estimate the thickness of deposited wastes, which provides the layered structure of the study area and certain, method depended, mechanical parameters as well. By theory, the frequency of resonance of an upper layer is a function of its thickness and the average shear velocity in it. Furthermore, the application of H/V spectral ratios of micro-tremors is a fast, straight forward and cost effective methodology, yielding the determination of the main resonant frequency of the soil. Based on this framework, 20 microtremor measurements have been carried out in a Landfill in Heraklion-Crete. Some of these measurements were deliberately close to drilled sites, where the basement had been reached. Three electrical resistivity tomographies were also used, in order to define the landfill structure such as, thickness, determination of different wastes distribution in the study area and other parameters. In addition, estimation of predictive Vs using empirical relationship between shear velocity and penetration resistance (SPT?s) were also conducted. Knowing the thickness and the resonant frequency, we estimated the shear (Vs) velocity of the waste cover. The final Vs model was confirmed using the results from the Vs-SPT correlation. The combinative implementation of the above mentioned geophysical and geotechnical methods have successfully defined geometrical and geotechnical/geophysical characteristics of the area under investigation in a fast and cost effective way.

Jan 1, 2005

By C. R. Peterson

A cutter vibration monitoring system is described which would map seam strata non-uniformities to permit guidance within the seam. An extremely simple and rugged transducer is used which is compatible with conventional cutters and cutter replacement practices, and believed to be suited to the mining environment. Laboratory tests show that the system can detect bedding planes in otherwise homogeneous material. A data display system which would employ the human operator's natural pattern recognition skill and judgement will be developed, Intended for remote control applications in general, the system is of direct interest for today's continuous excavators in coal or in any other machine excavated bedded deposit.

Jan 1, 1985

By Stig Premfors

Lamco Joint Venture is operating a Dravo Pelletizing machine to produce pellets from the natural slimes of an earthy hematite ore. The grate area of the machine 3.3 x 106 m equal to 350 m2 (3800 sq. ft.) and the installed fan capacity is 8200 HP. The limiting factor for production is normally fan capacity. This means that the processing fans can not pull the additional air (i.e the additional calories or BTUs) through the bed which would be required for increased production. A way to increase production without major modifications is to supply the additional calories needed for increase production by adding coal to the pellet feed. After successful laboratory tests following method of coal addition has been chosen and the following results have been obtained. 1. The ground coal is added to the slurry prior to the filters and the rotary dryer. 2. By adding 0.6% coal, an increase of about 15% in production rate has been obtained. 3. No significant changes of metallurgical properties have been observed (i.e. tumbler index, compressive strength, ferrous iron content, reducibility, Linder degradation and swelling). 4. No unexpected operation problems have been experienced. The pellet discharge temperature increases and is the limit for how much production can be increased by coal addition without making plant modifications.

Jan 1, 1971

By G. A. Rowell, T. M. Barczak, J. C. Zelanko

The US Bureau of Mines conducted a multifaceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps because the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements and microseismic monitoring, as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading and microseismic activity were monitored prior to, during and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and following the face bump. Shield load data, evaluated in an effort to identify trends that could be used to forecast coal bumps, appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source-location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1992

By M. F. Gleason, S. Burns, J. R. Arnold

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek mine in northern Nevada. After the long negotiations reached an impasse over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably, and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position. History In the spring of 1986, Davy McKee Corp. was contracted by Gold Fields Mining Corp. to provide design engineering and construction management for the chimney Creek Mine. Chimney Creek is located about 50 mi northeast of Winnemucca, NV in a remote part of Humboldt County. The nearest industry using utility power was the Pinson Mine, about 13 mi from the proposed plant site. The existing electric line was not capable of carrying another mine the size of Chimney Creek, which required 29 million kwh per year. There were three options available to Gold Fields for the power supply: 1 )Power could be supplied by the public utility from a coal-fired plant about 30 mi away by constructing a new line to the mine,

Jan 1, 1991

By Ray E. Harris

All of the major raw materials (silica, soda ash, limestone, and feldspar) needed to manufacture most grades of glass are found in Wyoming. Additional advantages for the manufacture of glass include the state's geographic location, a well-developed transportation network, a favorable tax structure (no corporate or personal-income tax), and low energy costs. Inadequate local markets and prohibitive transportation costs to other markets have been the major obstacles to developing a glass industry in Wyoming, the least- populated state in the nation. The Rocky Mountain region only recently became a major market for glass, especially for the Colorado Front Range and Utah's Wasatch Front. Currently, changing costs of the production of glass, an increased market for con- tainer glass in the Colorado Front Range, and innovative production and transportation ideas (e.g., production of selected types of glass and bulk shipments of specification-glass pellets) favor developing a glass plant in Wyoming. Thus, the Wyoming State Geological Survey (WSGS) and other state agencies have been conducting studies and contacting investors in an effort to attract a glass-manufacturing plant to the state. Between 1987 and 1993, three locations of silica-sand and -rock deposits were studied in Wyoming (Cassa, Plumbago Creek, and John Blue). Funding was provided by the WSGS operating budget and local and state Department of Commerce economic- development grants. The reports on these areas were released between 1988 and 1993. In 1988-89, a California-based company conducted additional drilling and feasibility studies and prepared to construct a glass plant in Cheyenne, using the Cassa silica source. However, due to losses incurred by some of their other investments, the company did not proceed. In 1997, the Wyoming Science, Technology, and Energy Administration (STEA) contracted a market study for glass manufactured in Wyoming, using information provided by the WSGS. The STEA contacted several major glass producers, and a major glass-producing company began feasibility studies in January 1998, for the construction of a glass plant. In June 1998, bids to supply brown beer bottles to the Budweiser brewery northeast of Fort Collins, Colorado, were submitted by at least two companies that were considering glass-plant sites in Wyoming.

Jan 1, 1999

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By H. W. Judges

A 16.5-kt/day underground molybdenum mine is being developed at Questa in Northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Construction of the underground mine began in 1979, and first production is scheduled for early 1983. A gravity block caving method has been selected for mining the ore. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. The shafts are being sunk under contract and the conveyor decline is being driven by Molycorp. The driving of the decline began in February, 1979 with a 10-man mining class. By the first of May, enough men had been trained to begin a continuous operation and by March 1, 1980 the face had reached the 1500 m mark. The heading is being driven with trackless rubber-tired equipment using a three-boom drill jumbo, 2.7 m3 LHD units and 7.3 m3 trucks. Ground support has been by rock bolts and wire mesh, followed by Fibercrete. A 16.5-kt/d underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. The new $200-million underground project will revitalize mining and milling activity at Questa, where small scale underground mining first began in 1920. Large scale open-pit mining was initiated in 1965 but now, because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for early 1983. The company expects full capacity - 9 Gg of molybdenum per year - to be reached in 1984.

Jan 1, 1980

By C. R. Tinsley

In maybe the world's first in a mine project financing, a US $55 million Rehabilitation Indemnity was given on behalf of the banks in a US $250 million loan to develop the Ranger uranium mine, Northern Territory, Australia. The basis of the financing was an estimate of removal of the tailings and replacement into the pit. The Indemnity was amortized by a sinking fund from the mine's revenues. Such a concept could be valuable for mineral developments in sensitive areas or jurisdictions such as British Columbia or Alaska.

Jan 1, 1992

By J. W. Leonard

Gravity based coal/mineral preparation plants must be operated to yield products of a quality satisfactory to existing markets; but, because of historic control problems, recovery is frequently sacrificed to achieve quality resulting in losses of valuable product. Plant control has ranged from intuitive in-plant spot quality judgments made by various operators to gross methods involving such devices as density gauges, floats, grab-sample on-the-spot sink-float tests, etc. Millions of tons of quality coal/minerals are lost to refuse each year, because of the historic lack of a continuous and dependable control system. The result is both serious economic as well as environmental losses. While the economic losses are obvious, less obvious environmental losses, in the case of coal, result from the misplacement of more ignitable quality fuel to refuse banks. A control system capable of supplying a market-grade coal/mineral product, while continuously minimizing product losses to refuse, has until recently escaped technology.

Jan 1, 1991

By J. A. M. Cano

An extensive research work was developed by Samarco Mineracao S/A to study the quality characteristics of blast furnace pellets produced with high content of MgO. Comparative blast furnace simulation tests were conducted both in Samarco and foreign laboratories. The objective was to evaluate the behavior of high MgO and normal Samarco pellets in the blast furnace operation. Additives such as dolomitic hydrated lime, dunite and magnesite were used for increasing pellet MgO content. The test results showed that pellets produced with high MgO content are similar in quality to normal Samarco Pellets.

Jan 1, 1991

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By M. J. Sanzotti, C. J. Bise

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing waste rock into the void created by mining. The paper also examines scheduling the process as a unit operation of the mining activity. Based on a review of background literature and interviews with representatives of various mining companies, public-interest groups and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing at a southwestern Pennsylvania mine was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of longwall systems in the United States. Further, at the mine used in this case study, concomitant stowing would reduce subsidence by only 50% of what would normally be incurred during full longwall caving, and the longwall coal-production rate would decrease from 3,630 t (4,000 st) per shift in the nonstowing case to 1,360 t (1,500 st) in the stowing case. A preliminary cost analysis reveals that pneumatic stowing would add from $5.79 to $11.57 per t ($5.25 to $10.50 per st) to the operating cost of producing coal at the case-study site.

Jan 1, 1997