Search Documents

By M. Gorman

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately 74 miles southeast of Las Vegas, Nevada. The property has been owned by the Duval Corporation, Cyprus Mining Company and Equatorial Mining of Australia. Mercator purchased Mineral Park from Equatorial in 2003. Mineral Park commissioned a 25,000 tpd copper and molybdenum concentrator in November and December of 2008. The process includes two stage milling (SAG and Two Ball Mills) fed by primary crushed ore. Metals are recovered in a copper-molybdenum flotation circuit consisting of mechanically agitated roughers and cleaners. The copper- molybdenum flotation concentrate is thickened and further processed in the molybdenum flotation circuit which separates the copper and molybdenum minerals into salable concentrates. The molybdenum circuit also uses mechanically agitated cells. This paper describes the plant and some of the highlights of the commissioning process.

Jan 1, 2010

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

By R. H. Kuhlman

The purpose of this paper is to describe the roles of cement and concrete in construction in general and, more specifically, as construction materials of the Southeast. For purpose of this discussion, the Southeast will include the geographic area composed. of the following 13 states: Alabama, Arkansas, Florida, Georgia, Kentucky, Louisiana, Mississippi, North Carolina, South Carolina, Tennessee, Texas, Virginia and West Virginia. In one sense, cement by itself is not a construction material. It is a finely ground manufactured mineral product, usually gray in color. Cement is mixed with water and sand, gravel, crushed stone, or other aggregate to form concrete, the rock-like substance that is the most widely used construction material in the world. Because cement is seldom used by itself for construction but is usually a component of concrete, there is no such thing. as a "cement" sidewalk, a "cement" highway, or "cement" building. Neither is "portland" a brand name. It is a generic term used to describe any cement that hardens in the presence of water and is made to standard specifications .. For all practical construction purposes, therefore, all cement is "portland." The name "port-land" was selected by the English inventor of the product in 1824 because concrete made with his product resembled natural building stone quarried on Portland, an English island. Although portland cement is not the final material which finds its way into completed construction, as the principal component of the most widely used construction material in the world, the location and process of its manufacture warrant some discussion

Jan 1, 1977

By J. L. Thompson

Lime made in a coal-fired, rotary kiln has two distinct parts: the interior of the pebble which constitutes about 90% to 95% of the mass, and the surface dust layer which is the remaining 5% to 10%. Uncalcined carbonate and impurities in the product may be present and will not contribute to the hydration reaction. Sulfur, in the form of calcium sulfate, inhibits the hydration reaction out of all proportion to its actual weigh-percent concentration (perhaps more than 100 times). If the stone contains dolomite, this will also inhibit the reaction as its rate of hydration may be nearly 3 orders of magnitude slower than that of calcium oxide. Early in the hydration reaction dolomite appears practically inert, but given sufficient time, it will hydrate. The heat of reaction is nearly the same as for calcium oxide, but the time necessary for complete hydration may be hours; whereas for calcium oxide it is only fractions of a second. The dust layer on the surface also inhibits hydration as it contains a collection of compounds which have low heats of hydration. This layer can tie up additional calcium and delay or prevent its reaction. In addition to these chemical processes, an important physical characteristic of the lime is its specific surface area. This is effected by the thermodynamics of calcination and the original stone grain chemistry. All of these factors are agglomerated in the gross slaking rate of lime. The total hydration of the chemical complex that is called commercial lime can be more easily understood by considering the individual reactions and combining them to form a more comprehensive picture of the situation. Calcium oxide and magnesium oxide hydrate similarly, differing only in their reaction kinetics. Dolomite, however, reacts differently than a simple mixture of calcium oxide and magnesium oxide as its hydration is strongly influenced by calcination thermo-dynamics and stone grain structure. Finally, the dust hydration and composition should be examined Understanding these reactions enables one to examine hydration reaction graphs with more insight into the factors which determine their shape.

Jan 1, 1978

By Hans Svensson

INTRODUCTION The Alimak method of raising (Fig. 1) was intro¬duced in 1957. Because of its flexibility, economy, and speed, it soon became the most used system of raising in the world. With the same unit, raises of various areas, inclinations, and lengths can be driven. Air-motor¬-driven raise climbers normally are used in mines with short raises (Fig. 2). For longer raises electric or diesel-¬hydraulic drives are used. The Alimak raise climber is designed entirely in ac¬cordance with the instructions of the Swedish Board of Industrial Safety (Arbetarskyddsstyrelsen). There are good margins of safety concerning the breaking strength of the material and the raise climber comprises safety devices and features that practically eliminate the risks of accidents. The drive gear of air-driven climbers is equipped with an air-operated brake which is automatically activated when air for the motors is shut off. There is a safety device which activates automatically at overspeed and a speed-regulated brake for descent by gravity, by which the raise climber can be taken down to the bottom of the raise in case of cutoff of the air supply. The raise climber climbs along a pin rack welded to a guide rail which also comprises pipes for air and water. The guide. rail can be extended by using 1- or 2-m (3.2¬or 6.4-ft) sections as the driving progresses. Each guide rail section is bolted to the rock wall by special expan¬sion bolts of Alimak design. Men ride up to the face in the cage, traveling com¬fortably and easily while material is transported on the platform. There is no dangerous climbing up ladders. The men are well protected during ascent and arrive in good condition at the face. The greatest advantages of raise climber systems are flexibility and versatility. The equipment provides a comfortable working position in vertical as well as in¬clined raises of any area and length. The direction may

Jan 1, 1982

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985

When I reached Warren after the "de luxe" South American expedition I had little idea what was in store for me. From the large check Thayer had handed me just before I left New York I was pretty sure the future would be good, and that before long it would involve Anaconda. Evidently, Mr. Thayer had left it to Dr. Ricketts and John Greenway to work out the details The next morning Greenway asked me to come to his office and told me that he and Dr. Ricketts had discussed the question and that Anaconda would make me an offer I could not refuse. They proposed to pay me almost $1000 a month, more than twice my current salary. They had agreed that I should stay with Calumet and Arizona for the rest of the year to help with Bisbee development and anything I could to assist with the New Cornelia plans and construction Of course I could not turn down such a flattering offer, as I had about reached the limit of advancement with a much smaller company in anything save a high executive job, and it would be a long time before I could be ready to change from exploration and geology to operating. Greenway and I agreed that I would stay with him for the remaining eight months of 1916 without any particular title but helping in any way I thought would be most useful. Bisbee and Ajo Study It turned out to be a busy half year, in addition to many good times with my Bisbee friends. The Uplift Club did not meet as regularly as in earlier years, but Mason Ross, Jim Lewis, Bill Gohring, Roy Mitchell, Hubert d'Autremont, Arthur Notman, and I did have many "bull sessions" and poker games. I saw much more of Greenway than before and made many trips with him to Ajo and later to the new

Jan 1, 1976

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 µ m fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 µ m. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1993

By N. Kuyucak

Uranium ores leached with sulphuric acid typically have poor dewatering properties. Applicability of controlled neutralization where gypsum precipitates as crystalline particles, improving dewatering properties of material was examined. Neutralized material was then dewatered using paste thickener to increase underflow density. The objectives are to maximize water recovery due to water scarcity and to produce suitable cemented paste fill material for optimizing underground ore recovery. Work was performed on acidic slurry samples collected after leaching but before the resin-in-pulp uranium recovery. Controlled neutralization greatly reduced volume of neutralization precipitates giving higher densities and improving the dewatering (filtration) properties. As a result it would be possible to increase the water recycled to the mill. Another benefit is that sulphate in the recycled water was reduced to saturation limit minimizing scaling of process equipment. Additional test work is needed; however, Unconfined Compressive Strength results imply that controlled neutralization increases the strength of paste fill and possibly offers opportunities towards a viable backfill option.

Jan 1, 2010

By Sadatoshi Ohmori, Karen Shinoda, Nobuharu Isago

Method of tunnel excavation is generally classified such as full-face excavation, bench-cut excavation, diaphragm with center pillar excavation, center drift advancing excavation and so on. These excavation methods should be selected properly in terms of ground condition, the area of tunnel section, the arrangement of construction. Center drift advancing excavation method in mountain tunnel construction, is often applied under quite weak ground condition, prior to the main tunnel widening excavation. Recently, the advancing drift is for the excavation of extreme larger section in main tunnel to confirm the stability of face. In addition, we make advancing deformation occur in drift when the construction was done in poor ground like squeezing and swelling ground, and the force occurred in main tunnel was expected to reduce by the effect of ‘dodging’ for support structure. Mechanical relation between drift and main tunnel has been mainly grasped on past experiences in Japan. However, the characteristic of tunnel enlargement was partially discussed by using the three dimensional analysis and the result was grasped by past experiences on the basis of each tunnel construction. It is considered that the natural ground stress is normally released as the advance displacement, but it was released after the main tunnel widening, causing a displacement and deformation increase. Up to now, the construction practice has shown the reduced displacement during the main tunnel widening excavation by the drift, and the numerical analysis agreed with above observation. However, there is no report found that the displacement and deformation at the time of widening excavation of the main tunnel become larger in case of a drift application. In Kyusyu area, western part of Japan, the northern part of Yoshinomoto tunnel was applied an advancing bench-cutting method for a center drift for the purpose of obtaining the geological information for support selection of the main tunnel in widening excavation. The shape of center drift was a perfect circle with a diameter of 4.0 m or 6.0 m and the same temporary support regardless of the geological situation. As a result, the displacement and deformation of the main tunnel after widening excavation were larger than the section where the center drift was not applied. Furthermore, the displacement and deformation of the main tunnel after its widening excavation was considered larger in the section where the cross-section of the center drift with 4.0 m diameter was applied than one with 6.0 m. Therefore, the center drift with a high rigidity support structure had the effect of suppressing the advancing deformation prior to the main tunnel widening excavation.

Jun 13, 2021

By C. I. Richman

The E h potential during of a iron reducing bacteria such as Aquaspirillum Magnetotacticum (A.M.) can be predicted by a growth model. It also reflects the adsorption of Fe+2 Cu+2 and Mn +2 ions, that can be incorporated into magnetic material called magnetosomes. The Ferric ion concentration during controlled growth of Thiobacillus Ferrooxidans (T.F.) is a function of the bacteria population curve, while A. M. ferrous ion concentration is a function of the integral of the population curve. Charting of the redox potential of T.F. during batch oxidation of refractory ores such as pyrite and pyrrhotite can be helpful to establishing onset and rate the bulk bio-oxidation rate. The onset of biooxidation is marked by an increase in Fe +3 ions that can be correlated with increased growth due to adsorbed electrons.

Jan 1, 1998

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

By Olivier Martin

In busy and historic cities, traditional open box metro stations are becoming outrageously difficult, unacceptable for the citizen and uneconomical. Hybrid stations provide an interesting alternative. In-house experience of Gautrain (South Africa), West bay (Qatar), Cairo line 3A (Egypt), and Melbourne (Australia) all aim to reduce disturbance to the city and its inhabitants during construction. Constructed in rock or in deep soil under water table, they take advantages of the latest construction techniques from cement grouting to freezing, and from traditional excavation of cavern to large tunnels constructed by sophisticated tunnel boring machines (TBM). Today, they form the ultimate construction challenge.

Jun 13, 2021

By N. Del Bel Belluz

Drilling underground in the Grasberg De-watering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are utilized; pilot-holes to probe ahead of the tunnel development to intersect aquifers ahead of the face; and de-watering holes to de-water rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, rates of 1050 psi static pressure have been recorded with flows from a NQ hole measured at 1350 gpm (US). The water flows can be slightly acidic, necessitating the use of stainless steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early to deal with these conditions. The collar gear is used to control water flows whereby the water is treated as an important resource. As a result, pm has established procedures to maintain safety of the drill crews, enable coring of the rock and to maintain safety of the miners who are driving the drifts.

Jan 1, 1998

By Peter G. Chamberlain

The Bureau of Mines is conducting research to boost domestic production of manganese. Virtually no mining exists in the low grade and/or small deposits that occur in this Country. One large, low-grade manganese deposit located in westcentral Arizona--The Artillery Peak district--was extensively studied and sporadically mined during the 1940's and 1950's. Although manganese mining in the district has been long dormant, recent studies indicate that the deposits may be amenable to economical production by heap and/or in situ leaching methods. A conceptual design for an in situ leaching system features undercutting and blasting a block of ore, leaching with SO2, and extracting the manganese as a sulfate or oxide. Possible applications to other manganese deposits depend upon formation permeability and specific manganese mineralogy.

Jan 1, 1981

By W. H. Renison

This paper will discuss the operation and maintenance of Molycorp's Quests Mine ore conveyor system. The 1.2 m wide, steel cable-reinforced conveyor belts are capable of transporting 1089 kt/h of ore over a belt line distance of 3124 m with a vertical rise of 518 m. A portion of the conveyor runs in a 2057 m long underground decline on a 10° slope. Six 448 kW motors power the main 1.2 m wide belts.

Jan 1, 1984

By A. D. Davis

The Bear Butte Creek watershed, in the northern Black Hills of South Dakota, shows the effects of past mining activities in the form of dissolved metals and arsenic in stream water. Bear Butte Creek, during normal flow periods, loses all of its discharge to sinkholes that recharge the Madison Limestone aquifer. This work focused on the geochemical transport and fate of arsenic and on understanding ground-water flow conditions in the Madison aquifer through development of a three-dimensional ground-water flow model that was coupled to a geographic information system (GIS). Stream sampling and discharge measurements helped determine sinkhole losses and loading rates. Column laboratory tests provided data on arsenic adsorption and the mixing of stream water with aquifer water, which also was simulated with the geochemical models, pHREEQE and NETPATH. The models and GIS can be updated with new information and will be useful in managing the water quality of the Madison aquifer.

Jan 1, 1997

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept's economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

By J. E. Spencer

Mesozoic and Tertiary mineral deposits in west-central Arizona are commonly associated with Mesozoic thrust faults and Tertiary detachment faults, respectively. Quartz-kyanite rocks and pyritic quartz-sericite schists with local anomalous gold are the product of probable Jurassic argillic alteration of Jurassic volcanic, sedimentary, and plutonic rocks followed by Cretaceous thrust burial and associated metamorphism. Slivers and sheets of Paleozoic carbonates along Mesozoic thrust faults were locally sites of syn-and post-thrust mineralization. Widespread brecciation along Tertiary detachment faults resulted in increased permeability along fault zones. Elevated thermal gradients also resulted from detachment faulting and apparently caused convective aqueous-fluid circulation along detachment faults and associated Fe+Cu±Au mineralization.

Jan 1, 1988