Search Documents

By M. Ahmadiantehrani

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, concentration, hypochlorite consumption, and bed height on the total gold extraction. At high pH, the hypochlorite stability increases and thus, hypochlorite consumption is decreased. At room temperature, the total gold extraction is proportional to the hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10 and 80 percent are obtained for 12 and 167 lbs/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption gold extraction was increased by shortening the ore column height. Finally, calcium hypochlorite is more effective than sodium hypochlorite.

Jan 1, 1990

By David P. Kimball, Dalva L. Moellenberg

On May 21, 1990, EPA released its Strawman II draft program for mining wastes. It proposes to expand RCRA regulation of mining operations to include materials other than wastes. Strawman I1 would establish strict standards for the states to follow, rather than technical guidance. It proposes to establish performance standards; design criteria; monitoring requirements; and corrective action, closure, post-closure, and financial assurance requirements. It suggests "pollution prevention" concepts for mining operations. This paper explores the Strawman II proposals, particularly the technical criteria, and addresses several of the important concerns raised by industry.

Jan 1, 1991

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 2,903 t (3,200 st) of ore per day, with an average gold grade of 0.4 opt. The mine’s horizontal extent is large, 762 by 152 m (2,500 by 500 ft), while its vertical extent is 6 to 61 m (20 to 200 ft). A high density of joints occurs within the host rock. Based on rock mass rating and field observation, the ground conditions at Leeville can be characterized as poor to very poor. As such, heavy ground support is required for its mining operation. Ore zones with a height in excess of 10 m (35 ft) are considered for longhole stoping. A typical stope measures 6 m (20 ft) wide, 30 to 55 m (100 to 180 ft) long, depending on the ground conditions, and 10 to 30 m (35 to 100 ft) high, depending the thickness of the ore body, yielding 9,100 to 18,000 t (10,000 to 20,000 st) when completed. Narrow ore zones, less than 10 m (35 ft), are mined using cut and fill. Drifts at the Leeville Mine are 4.6 m (15 ft) wide by 4.6 m (15 ft) high. Because of poor ground conditions at this mine, the establishment of a ground control monitoring system is key to operating both safely and successfully. This monitoring system is composed of comprehensive instrument design and installation. Instruments include multi-point borehole extensometers (MPBX) and “stretch measurement to assess reinforcement tension” (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two years’ application and measurement, useful data has been collected and continues to be collected; this information will be used to design future stopes and infrastructure. The system makes engineering and operation teams able to do their job with more confidence and efficiency.

Jan 1, 2009

By P. T. Luckie

The selectivity curve -- a continuous function which predicts the expected proportion of feed material of a particular size that will appear as coarse material -- is the preferred model for describing classification. In a previous paper (I), the authors presented a technique for determining the selectivity curve of a classifier from experimental data. The separation process is defined by a binomial distribution of the form [ ] where s(x), the probability of particles of size x reporting to the coarse stream, is obviously the selectivity value for material of size x.

Jan 1, 1975

By F. W. Brackebusch

Paste is a high density mixture of water and fine solid particles with a relatively low water content (10-25%) such that the mixture has a consistency as measured by the ASTM slump cone test from slightly greater than zero up to nearly 12 inches (305mm). Particles of different size classes will not segregate or settle when the paste is not being agitated or when it is stationary in a pipeline. Cement may be a component of paste. Larger particles of aggregate can generally be added to a paste without greatly changing the pipeline transport characteristics. A paste may bleed water slightly when it is allowed to be motionless for periods of up to several hours, but the solids do not become so dense that the paste cannot be easily re-fluidized. The dividing line between the definition of a high density slurry and a paste is not sharp. It is a practical matter that must be considered when designing a pipeline transportation system. If the pipeline is very short, there is very little risk of plugging the pipeline with a high density slurry when flow is stopped for short time periods. With longer pipelines the mixture must remain stable without motion for periods as long as several hours to avoid pipeline plugging. The fine particles in a paste mixture can be composed of mine tailings or naturally-occurring clays, silts and fine sands. The mineralogy of the particles thus can have a wide variety from quartz and feldspar to clays, micas and even salts.

Jan 1, 1993

By A. House

Newmont Mining Corporation owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006. Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix needed a process option to treat lowgrade transition and oxide copper ores. This meant that potentially revenue generating ore was being mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a run-of-mine (ROM) heap leach pad and solvent extraction/electrowinning plant (L-SX/EW). This paper will discuss the synergies and challenges of developing a copper L-SX/EW plant at the Phoenix copper-gold mill.

Jan 1, 2010

By Charles H. Greene

This paper will describe briefly the steps taken in the development of a Central Florida phosphate ore deposit from acquisition to mining. Further, the design and early operation of the mining and beneficiation facilities will be depicted. During the 1950's, with confidence in the continually increasing requirement for phosphate fertilizer materials essential for producing food, I'. R. Grace & Cc acquired the Hookers Prairie tract containing approximately 45 million metric tons o. (50 million short ton~ of potential phosphate rock product. In 1973, at a point when the Grace captive need for rock was being greatly enlarged by a planned doubling of its Bartow phosphate chemicals plant capacity, the decision was made to expand existing phosphate rock production by building a new mine and plant. The initial annual capacity was to be 2.3 million tons (2.5 million st); however, subsequent investigation pointed to a higher than estimated dragline operating factor 'and the forecast of annual capacity was set at 2.5 million tons (2.8 million st).

Jan 1, 1977

By Matthew Preedy, Anthony Pooley, Mike Wongkaew, Dirk Bakker, Raghu Bhargava

Sound Transit’s ST3 program will add 62 miles of light rail to the Puget Sound area, including connections to the neighborhoods of West Seattle and Ballard. These connections include considerations for both elevated and tunnel alternatives in West Seattle and Ballard, as well as a new tunnel and six underground stations in the densely developed downtown Seattle. This paper describes the conditions and constraints along the corridor, and the latest development in the ongoing process to plan the underground guideways and stations.

Jun 13, 2023

By H. M. Castrantas

Caro's (peroxymonosulfuric) acid has been reported to destroy WAD (weakly acid dissociable) CN-but, until recently, the technology has not been demonstrated in other than a laboratory setting. During the last two years, Caro's acid has been shown to successfully detoxify WAD CN-in tailings at two large North American gold mines. Using on-site FMC generators, Caro's acid reduced the WAD CN-from 40-55 ppm to below 20-35 ppm WAD CN-, the target range for the two mines. The detoxification costs using Caro's acid were less than 50% of the treatment cost of using hydrogen peroxide, the previous oxidant of choice. In addition to the considerable savings in CN-detoxification costs, lower WAD CN-values were achieved and the detoxification time with Caro's acid was greatly reduced compared to hydrogen peroxide.

Jan 1, 1995

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By G. M. Wilemon, B. J. Scheiner

The Bureau of Mines conducted investigations on extracting phosphate values from fine-particle wastes generated during the mining and beneficiation of phosphate ore by leaching dried wastes using a H2SO4-methanol mixture. Although phosphatic clay waste contains up to a third of the phosphate originally present in the ore, recovery of these values represents a significant challenge due to the fine grain size of the material, the particles averaging less than one micrometer in diameter. Waste samples obtained from two Florida producers yielded phosphate extractions of 71 and 84 pct, respectively, when leached under ambient conditions and at a stoichiometric acid ratio of 1.4:l. Elevated temperatures did not improve the amount of phosphate extracted. Undesirable A12O3, Fe2O3, and PlgO impurities were largely rejected; higher grade wastes gave acids that meet established industry impurity standards and lower grade samples yielded acids that marginally fell short of the standard. Separation of the crude acids from the insoluble residues was accomplished via vacuum filtration through either filter paper or commercial filter cloths. Both filtration rates and solids retention were improved by the addition of 0.5 lb/ton of poly(viny1 acetate) (PVAc) or poly(ethy1ene oxide) (PEO) to the methanol-acid slurries. These results show potential for substantially increasing the reserves of an important domestic resource.

Jan 1, 1989

By John D. Hanifin, C. Kevin Moon, Eric C. Wang

Value Engineering on Connecticut DOT’s Walk Bridge selected the trenchless option for utility relocation to address the channel crossing’s environmental concerns. The design and construction considerations of the twin micro-tunnel drives and associated shafts are presented. Key challenges included vertical alignment selection to achieve minimum one-tunnel diameter stable cover within thin glacial till underlying extremely soft clay, limited choice of pipe and joint materials meeting stringent non-metallic conduit requirements, thermal grout backfill application, and the close proximity of temporary trestle piles. Mitigation measures were developed for potential point loading pipe damage from remnant boulder fragments in the annular space.

Dec 1, 2022

By Eoin Murphy, Stephen Beauchamp, Steven Cowell

"INTRODUCTION Electrification of the heavily trafficked Manchester to Preston route by Network Rail required the rehabilitation of the Victorian era Farnworth Tunnels to accommodate 21st century high speed trains. Network Rail, J. Murphy and Sons Ltd (JMS) and OTB Engineering Ltd (OTB) collaborated closely to complete these works in close proximity to heritage infrastructure whilst maintaining a rail service on the route. This significant challenge has been mastered by a combination of detailed investigation, complex modelling, robust design, extensive monitoring, ground treatment, secant piling, sprayed concrete, steel arches and segmental lining techniques. Investigation of the “Down” Tunnel found deformation and cracking of the lining and this was reconstructed during 11 weekend possessions. The “Up” Tunnel was filled with low strength concrete and a 9m diameter open face shield was used to construct an 8m diameter segmental lined tunnel during a 23 week blockade whilst traffic was maintained in the “Down” Tunnel. ELECTRIFICATION OF THE RAILWAY The Farnworth Tunnel project is part of the UK wide £1bn Railway Upgrade Plan to provide improvements throughout the rail network which includes the Manchester to Preston route. The project also supports the UK Government commitment to build a “Northern Powerhouse” by improving links that bind northern England together and which will help it release its full potential with a more balanced, healthier economy. The majority of the current UK rail network infrastructure resulted from the rapid growth of the railways in the mid to late 19th century which means that most of the existing tunnels are over 120 years old. Over the centuries the introduction of larger rolling stock has reduced the original clearances provided in tunnels. The electrification of a route requires that any over-line structures provide clearance for Overhead Line Equipment (OLE), new rolling stock and to meet modern standards. As part of Network Rail’s current electrification programme a further 36 tunnels have been identified on routes requiring electrification. Not of all these Victorian structures will require alterations to provide OLE clearance but the condition of the existing tunnels and modern fire / waterproofing requirements may ultimately dictate the need for rehabilitation."

Jan 1, 2016

By S. Partney

Waste clay ponds are a necessary part of the phosphate rock beneficiation process. They are large, averaging a square mile in size; unsightly, in that they protrude 20 to 50 feet (6 -15 meters) above natural grade; stabilization and reclamation is slow; and they have had a history of catastrophic failure. The State of Florida has never published a specific rule regarding the configuration or height of these ponds, but has enforced numerous policies along these lines. The current rules are given and interpreted, along with the reasoning for current policy. In addition, an overview of the history of the policies, and an attempt at explaining the reasons for the changes that have occurred is given. The industry has been forced to make major monetary decisions, having effect for decades on mine economics, in a constantly changing regulatory environment. The Bureau of Mine Reclamation is confident that a direction of regulation has been solidified, but changes are still to be anticipated.

Jan 1, 1998

By Theodore H. Budd, Austin M. Cooney

The paper discusses the background and theories of the conditions that led to the settlement of a Lovat TBM mining in an earth pressure balance mode on a recent project in Milwaukee, Wisconsin. The settlement occurred independent of human error and caused the cost of the project to increase 50 percent. The project was mined in the highly congested downtown area in alluvial and estuarine deposits, 7.6 m below the water table with a prescribed contract requirement that precluded dewatering in deference to concern for foundations of adjacent existing buildings.

Jan 1, 1989

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010

By Mike Wongkaew, Brandon Kluzniak, Per Vilhelmsson

Rail access to Ontario International Airport (ONT) has long been a goal of San Bernardino County Transportation Authority (SBCTA) to increase public transit options to ONT and provide incoming ONT passengers improved access to San Bernardino County and the greater Southern California region. This paper describes the planning for the Design-Build-Operate-Maintain (DBOM) delivery of an emerging technology tunnel connection between the Rancho Cucamonga Metrolink station and ONT. The paper discusses key technical considerations, challenges, and opportunities; conceptual configuration development; and construction planning and establishment of the footprint for the underground connection.

Dec 1, 2022

By John J. Stetler

Introduction Samarco Mineracao S.A. is a Brazilian corporation jointly owned by S.A. Mineracao da Trindade (SAMITRI) and Utah International Inc., with 51% and 49% interests respectively. Headquartered in Belo Horizonte in the state of Minas Gerais, Samarco owns and operates an open-pit mine capable of producing 10 Mt/a (11 million stpy) of iron ore; a concentrator rated at 7 Mt (7.7 million st); a 12-Mt (13.2-million st) capacity pipeline transportation system; a 7 Mt (7.7 million st) filtering and pelletizing plant; and a harbor facility. The mine, concentrator, and initial pipeline pump station are located at Germano, near the town of Mariana, about 300 km (186 mi) north of Rio de Janeiro by air. The pipeline terminal, pellet plant, and harbor are at Point Ubu, 70 km (43 mi) south of Vitória the capital city of Espirito Santo State, and about 300 km (186 mi) by air east of the mine. The 396-km (246-mi) pipeline uses 508-mm (20-in.) pipe except for a 53-km (33-mi) section where 457-mm (18-in.) pipe is used to absorb and control slack flow through increased velocity in one of the areas along the route. Iron Ore Slurry The hematite iron ore concentrate produced at the Germano plant is processed by grinding the average 53% run-of-mine itabirite iron ore to -150 µm (100 mesh) for gangue liberation. It is treated further by cyclones to remove the 10 µm (1250 mesh) slimes to prepare the ore for flotation. During the multistage cationic flotation operation, the silica is reduced to make low silica (-0.9%) concentrate for the direct reduction (DR) iron-making process or to make normal silica (-3.5% +2.5%) concentrate for the blast furnace (BF) iron-making process. The concentrate then is reground further to meet the particle size requirements for pelletizing. The reground hematite concentrate is screened in closed circuit with the regrind mills for close control of the maximum particle size, not to exceed 3.5% +75 µm (200 mesh) for pipeline wear protection. Thickened concentrates at 70% solids are pumped to four 5-kt (5,510-st)(dry) agitated slurry storage tanks that hold the feed before it goes to the first pipeline system pumping station. Pipeline Capacity The pipeline system was designed to transport 12 Mt/a (13.2 million stpy) at 65% solids with an average minimum safe operating velocity of 1.5 m/s (5 fps). The pipeline will transport 5 Mt (5.5 million st) in 1982. The system, therefore, is moving the slurry in 13-kt (14,330-st) batches, dispatched at intervals to move 20 kt/d (22,050 stpd). In operation, the pipeline has exceeded its 93% availability design factor. Pipeline Facilities Pump station No. 1 is located at the Germano minesite 1 km (3,330 ft) above sea level. It has the following principal equipment: • four 5 kt (5,510-st) (dry) agitate slurry storage tanks; • two centrifugal charge pumps (one stand-by); • a 217-m (712-ft) safety loop; • seven mainline positive displacement triplex plunger pumps (189 m3/h, or 832 gpm, at 14.9 MPa, or 2,162 psi, maximum output pressure); • four corrosion-erosion spools; • a control and command center. Operation The output at pump station No. 1, with 66% solids, is pumped 151

Jan 10, 1982