Search Documents

By G. J. Joy, J. P. Rider

Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 30 m/min (100 fpm). This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the U.S. National Institute for Occupational Safety and Health (NIOSH) is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research (OMSHR) Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities — 152, 213 and 274 m/min (500, 700 and 900 fpm)— and at water pressures of 689, 1,034 and 1,379 kPa (100, 150 and 200 psi). Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Average reduction efficiencies of at least 90 percent were seen at the three sampling locations closest to the shearer for all three manifold systems at nozzle spray pressures greater than 689 kPa (100 psi). Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer, a spray manifold was fabricated and evaluated at an underground operation.

Jan 1, 2016

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By K. Fleck

Energy West Mining Co. (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, UT. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the in situ coal strength and load transfer mechanisms for improving two-seam designs and support systems.

Jan 1, 2012

By Brian Fulcher, Matthew Bartlett, Jarrett E. Carlson

This paper discusses the challenges to complete the construction of two large underground Metro stations and connecting tunnels in the Tren Urbano system. The completion work includes the installation of specialized mechanical and electrical systems, extensive architectural finishing as well as coordination with systemwide power and controls installed by others. A unique feature of this project was the simultaneous design and construction of the structural/civil/architectural/mechanical/electrical works by KKZ separately from the power and control systems under the management of the Owner, its consultants and other contractors. Completion of this project comes after almost six years of continuous design and construction in a dense urban environment. The project was confronted by many challenges that could only be met with the combined efforts of the Joint Venture team in close cooperation with the Owner and its System wide Contractor. This paper will also address many of the major design and construction changes implemented to suit the Owner’s requirements.

Jan 1, 2003

By I. Mikov

Established in the 60-ies, the Zlatna Panega quarry is a cement raw materials quarry supplying 95% of the needs of the Zlatna Panega Cement Plant with limestone, marl and other silica-aluminates. The two major types of raw materials are formed by accordingly dipping strata of Upper Jurassic limestones and lower Cretaceous marls. Between them there is a ?transition-zone? or ?contact-zone? of a high-silica content layer, about 5-m thick, defined as ?flint? by investigations including spot sampling throughout the quarry. For many years this ?contact-zone? layer was neglected due its negligible thickness. Further, with the increasing demand on the quality of the raw materials feed to the Plant and the focus on variability of the chemical and mineralogical components, it was decided not to mine any of the parts of the quarry contaminated by this material, for about three years. The latter had an impact on the availability of operating benches that could result in a substantial decrease in the total recoverable re-serves of Zlatna Panega, particularly with respect to marls. There were considerations for resorting to a partial, selective excavation of the quarry pit with a reduced lifetime for the lime-stones and re-opening of an other (currently in-active) marl quarry at a distance of 6 Km from the Plant. The Quarry Team of the Zlatna Panega quarry was assigned to study the problem. The ?contact? layer was duly confirmed with systematic geological (including mineralogy) studies, statistical analysis of available data, surface sampling and shallow exploration drills, resulted into distinguishing a third type of reserves and their credible subsurface delineation by means of geological 3-D modeling and quarry design. A new quarry design was finally elaborated with a view of providing flexibility in mining, utilization of the total volume of all available reserves and maximizing the mine life of Zlatna Panega quarry. An industrial test took place in December 2005, by using the contaminated parts of the quarry (co-mining of the ?contact-zone? materials) at a contribution of 15-20% in the raw materials mix, as dictated by their contribution in the total recoverable resources of the quarry. The purpose was to investigate the viability of this solution ? in line with improved quarry planning ? without compromising the quality of cement production and the efficiency of Plant Operations. Results were overall successful.

Jan 1, 2006

By Peter L. Hofmann

Significant quantities of nuclear wastes were first generated in 1944 as a byproduct of the national defense program. To establish the current inventories and future projections of nuclear waste products is not a simple task. The Oak Ridge National Laboratory recently issued a report which now constitutes the official basis for nuclear waste inventories and projections. Radioactive wastes originate from five major sources (U .S. Department of Energy, 1980b) : (1) From the commercial nuclear fuel cycle related to the production of electricity , (2) From defense related activities, (3) From institutions such as hospitals, universities, and research foundations, (4) From industrial uses of radioisotopes, and (5) From mining and milling of uranium ores.

Jan 1, 1981

By Richard E. McGee

The paper presents a description of the procedures that were used to generate a ventilation criterion based on measurements of ambient mine air exhaust pollutant gases and ventilation airflow quantities. Today's economics dictate that a ventilation requirement be based on actual operating conditions. This will assure optimum economics and a safe working environment at the same time. The paper presents a methodology by which a ventilation requirement is based on the average maximum expected concentrations of nitric oxide (NO), nitrogen dioxide (NO2), carbon monoxide (CO), and carbon dioxide (CO2) that equipment operators in one of our Southeast Missouri mines will be subjected to. A graph has been generated whereby the expected maximum levels of NO, NO2, CO and CO2 are plotted against the ventilation quantity of a mine stope.

Jan 1, 1982

By R. R. Swanson

Liquid ion exchange is becoming more and more important in hydro-metallurgical processing and recovery of metals. The key to success for this process are reagents which have suitable operating characteristics. One of these important characteristics is a relatively fast phase separation rate in the extraction and stripping circuits, as this greatly affects the size of plant required. A test for measuring phase separation rate is needed to help evaluate liquid ion exchange reagents. Such "a test also would be useful for evaluating carrier solvents that are used for diluting the re-agents. In fact, one standard test method would be very desirable as it would provide a common basis for comparing reagents and sol-vents. The phase separation test described in this paper has been used successfully for several years with the copper reagent, LIX®64N. The test is set up for feed liquors containing low copper concentrations. For other types of systems, modifications in procedure probably would be necessary. However, this test and the associated apparatus could be the basis for a standard phase separation test.

Jan 1, 1972

By Finn E. Bronner

HISTORICAL PERSPECTIVE "Blessed be the Lord my strength, which teacheth my hands to war and my fingers to fight." Thus sang David three thousand years ago, in tacit acceptance of the condition of war, and in praise of the exceptional military skills with which this warrior king of Israel was endowed. He had cause to exult, for he had consolidated King Saul's conquests and added new ones of his own, not least of which was the capture of Jerusalem. David revealed in this operation that his mastery of the military arts embraced not only the weaponry and tactics of his day, but also strategy and that oldest of intelligence techniques: spies. The Jebusites, who built Jerusalem, had encompassed the city with the first of its many walls, but had neglected to incorporate the sole reliable water supply within its perimeter. This was Ain Gihon, today called the Fountain of the Virgin, which bubbled out on the east slope of Mount Ophel, one of the ridges on which Jerusalem was built, and drained eastward into the Kidron Valley. Water was brought into the city in the traditional manner: by women descending the stony trail outside the wall to fill their jars at the spring. But this essential daily activity was vulnerable to interruption by a hostile force outside the walls. To remedy this weakness, the Jebusites had driven a gallery from the spring a short distance into the water-bearing limestone under the city, and there cut a small collecting basin in the rock, a common way to develop springs throughout this arid region. But then the Jebusites dug a small vertical shaft from the roof of the gallery above the cistern upward about 15 m. From the upper end of this shaft, they constructed a narrow inclined tunnel with rock-cut steps leading up to the city streets. Thus the water supply could be reached even in time of siege.

Jan 1, 1979

By M. D. Loy

In addition to products available from private vendors, many useful programs are developed at universities - in fact, many of these programs led the way to commercial development. Other projects are assigned to consultants with backgrounds in system design and mining. Both types of development have led to programs that can be acquired for the cost of a tape or disk. This paper highlights several underground mining packages. These programs consist of: ? USBM model-developed by the United States Bureau of nines. ? PSU model-developed by Pennsylvania State University. ? VPI model-developed by Virginia Polytechnical Institute and State University. ? NUS model-developed by NUS Corp.

Jan 1, 1987

By James W. Cooksley

Through the early stages of metamorphism, when diffusion is the predominant mineral forming process. there is a tendency toward homogenization of rock units; but there is also zoning resulting from differing primary lithology and structure. Later stages of metamorphism, when infiltration occurs, tend to intensify zoning within the rock mass. The above concepts have been borne out in exploration of talc deposits and skarns. Initially, geologic mapping and soil sampling are directed to understanding mineralogy and petrology. Later, seismic methods are employed to further define lithology in the subsurface. Magnetometer surveys can also define some metamorphic units efficiently. Then, drilling must ensue to confirm lithology and determine extent of mineralization.

Jan 1, 1992

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By Roshan B. Bhappu

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientific research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump leaching process and discusses salient features and parameters that may be helpful in improving such operations.

Jan 1, 1968

By Edward J. McNamara

Sulphur as an element has been used for centuries. The technique of storing, handling and transporting it in its various forms has changed through the years. Freeport Sulphur Company, a division of Freeport Minerals Company, has produced sulphur since 1912. The first storing and transporting of this product as a liquid began in 1947. Significant environmental problems occurred in the handling of solid sulphur in the late fifties and early sixties. Since the sulphur WAS produced in the liquid form and the major customers used it in the liquid form, it became obvious that a liquid transportation system was the solution. The liquid sulphur delivery eliminated the dusty and hazardous handling problems and the contamination of the sulphur by dirt, acid, moisture and other materials. The remelting by the customer to use the sulphur is thusly eliminated with a savings in energy. In addition, this change in the mode of handling permitted a broad development of new sulphur mines in the marshy coastal area of Louisiana and offshore in the Gulf of Mexico.

Jan 1, 1978

By J. M. Smith, T. R. Horton, R. L. Blanchard, T. W. Fowler

INTRODUCTION Uranium mining operations release radioactive materials into both air and water and generate large quantities of solid wastes containing low levels of radioactive materials. Solid wastes produced by mining operations remain on the surface at many inactive mining sites in the Western United States. These mining effluents may present a potential health and environmental hazard. Therefore, Congress, in Section 114(c) of the Uranium Mill Tailings Radiation Control Act of 1978, instructed the Administrator of EPA to prepare a report identifying the location and potential health, safety, and environmental hazards of uranium mine wastes and to recommend a program to eliminate these hazards. Several facts and limitations helped shape the method and approach of the EPA study. Little information on uranium mines was available; measurement information that was available on uranium mine wastes was frequently influenced (biased) by nearby uranium mills; time and resources did not permit comprehensive field studies to provide additional data; and there are inherent variations between uranium mines and sites that complicate generic assessments of mine wastes. To accommodate these facts, the EPA developed conceptual models of uranium mines and made health and environmental projections from them. The models were based upon available data from the literature, supplemented with information from discussions with persons inside and outside the EPA, and by doing several short-term field studies in Texas, New Mexico, and Wyoming. When necessary, conservative (maximizing) assumptions were employed. This paper presents a brief account of a part of the EPA study dealing with the potential health and environmental effects caused by active surface and underground uranium mines. Airborne contaminants are emphasized, although solid and liquid effluents are also included. Due to the limited space, only the methods and parameters used and the results of the assessments will be presented here. Anyone interested in the source of the data used and the development of the parameters should refer to the EPA report (Blanchard et al., 1981). The occurrence and emissions of stable elements were included in the EPA report, however, due to space limitations and their apparent small impact, except for possibly at some specific mines, only radioactive sources will be included in this presentation. MODEL URANIUM MINES The model surface mine was located in the South Powder River Basin of Wyoming and the model underground mine was located in the Ambrosia Lake area of New Mexico. These are the prevalent type mines in those areas. The model mines were based on the average production parameters of the 63 open pit mines and the 256 underground mines that were operating in the United States in 1978 (Department of Energy, 1979) and on a report of an extensive study of open pit mines in Wyoming (Nielson et al., 1979). Information contained in environmental impact statements and in reports from federal and state agencies was also used. Parameters for the model mines are listed in Table 1. The surface mining scenario is that 7 pits are opened in the 17-year mine life with overburden from each successively mined pit used to backfill a previously completed pit, resulting in an equivalent of one pit of overburden (2.4 year production) stored on the surface. No backfilling is assumed at the underground mine. Overburden or waste rock, ore, and sub-ore are separated into separate piles that are either rectangular in shape with length twice the width or in the shape of a frustum of a regular cone. Both shapes have 45 degree sloping sides. To account for bulking, the volume of the material comprising the piles was considered to be 25% greater than the volume of material removed from the ground. It was assumed that dewatering was required at both mine sites. Wastewater discharge rates at the surface and underground mines were assumed to be 3.0 and 2.0 cu m per min, respectively. SOURCE TERMS The following radioactive contaminants at active uranium mines were assessed in the EPA report: 1. Radioactive particulates in a) wind suspended dust from waste rock (overburden) pile, sub-ore pile, ore stockpile, b) suspended dust from mining activities (rock breakage, loading and unloading ore and wastes), and c) vehicular dust, 2. Rn-222 emanation from waste rock (overburden) pile, sub-ore pile, ore stockpile, and mining activities, 3. Rn-222 emanation from mine surface areas, and 4. Radionuclides in wastewater discharged to land surface. Estimated average annual dust emissions (item 1 above) from the model mines are listed in Table 2. Emission factors and the assumptions used to estimate these dust emissions are described in detail in the EPA report. Radioactive source terms were computed for each of the sources; dust emissions were multiplied by the concentrations listed in Table 1

Jan 1, 1981

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

By R. J. Weigel

The Santa Fe Railway serves the dominant U. S. potash producing region which is centered at Carlsbad, NM. This rail system extends over 12,000 miles stretching from Chicago to the Texas Gulf Coast to the state of California. (see Figure 1) Since Carlsbad mining operations began in the 1930?s, Santa Fe has been transporting potash to many of the important grain producing areas of the country and to the major ports in Texas and California. Santa Fe has maintained a close relationship with the potash companies and has adopted a marketing philosophy of attempting to maximize opportunities for the Carlsbad producers where it is mutually beneficial. Potash has been an important commodity for the Santa Fe. It accounted for 8% of our revenue in 1965 and 3% in 1984. In the 1950?s, Carlsbad became the second largest revenue producing point on the Santa Fe. But this prominent position has diminished as ore reserves became depleted, imports flooded the U. S. market, and truck transportation developed.

Jan 1, 1985

By R. Bruce Thorndycraft

This paper will describe several modifications to design of con­ventional oxide gold heap leaching. They are targeted at reduc­ing costs and simplifying heap operations. These modifications were conceptualized during consulting work on over 90 differ­ent heap leaches. In 1995, a unique opportunity arose to imme­diately apply all of these design concepts to the permitting and construction of a new facility at the American Girl Mine in southeastern California. American Girl Mine has operated since 1987. In April 1995, the mine faced a situation with grave consequences for cash flow. Approval for mining of a new ore zone, Oro Cruz, had just been granted, after lengthy delays by California regula­tors. All existing pad space would be filled by October. Only 6 months were available, and new pad siting and design were still undecided. Permitting of a new pad had not begun. Options were quickly reviewed. A strong criteria for pad site selection and design was ease of permitting. There was also a strong desire to install a system that would achieve better met­allurgical recovery and reduced operating costs, compared to previous heaps at this mine. One site offered the best chance for rapid permitting. It was the site of the original 1987-90 heap leach. This already dis­turbed ground contained 1.6 million tons of heaped ore. The old heap had just completed detoxification and was about to be signed off as a Group C waste, ready for reclamation. Instead of recontouring and revegetating the old heap, which the reclamation plan anticipated, we offered BLM and the County something even better. We proposed to off-load much of the detoxed old heap, and reuse the space. The off-loaded material would be back-filled into the original open pit, imme­diately adjacent. While the footprint of the proposed new pad was much larger, the reuse of disturbed ground, and backfilling of the open pit, had very strong appeal to the regulators. Our permitting strategy included the technical design of the proposed new facility. Many of the new design details also appealed to the regulators, particularly the "zero active ponds" concept.

Jan 1, 1996

By T. Stuczynski

In the past ten years about 3000 wastewater treatment plants have been built in Poland. The result of this development has been a massive increase in overall sludge production. According to data supplied by the Ministry of Environmental Protection, 400,000 dry tons of sludge are generated every year in Poland (Koblak-Kalinska 1996). Still it is difficult to estimate the amount of sludge, which is used in agriculture or for reclamation purposes. However, it can be assumed that this comes to no more than 10 percent of all sludge produced in Poland on a yearly basis. Thus it became obvious that an urgent solution to this problem was needed. Local authorities in Silesia realized in the early 90?s that a demonstration was necessary to encourage the proper utilization of sludge. This was the basis for establishing the Biosolids Subpart of the Silesia Project, which addressed the use of biosolids in the reclamation of mining and smelting dumps (Stuczynski et al. 1996). Metal waste sites themselves are known to contain more than 87 million tons of waste (Pistelok et al. 1995). Each year this amount increases by approximately 400,000 tons. We realized that a simple solution for stabilizing these sites would be to cover them with vegetation in order to reduce leaching of toxic elements, as well as to keep metallic fugitive dust from entering the environment. The reclamation of smelter waste sites, which was carried out within the framework of the Silesia Project was a joint effort of local government, industry and international research institutions/agencies, including the US Environmental Protection Agency (EPA), the Center for Research and Control of the Environment (OBIKS), Virginia Polytechnic Institute and IUNG. One of the goals was to evaluate the possibility of adapting the rules of sludge management currently used in the United States to conditions commonly found here in industrial regions of Poland. However, the main objective of the Silesia Project was the development of guidelines concerning all aspects of sludge use for the reclamation of degraded lands and waste sites. Biological aspects related to reclamation of metal waste with the use of biosolids will be discussed in this paper.

Jan 1, 2002

By Xiang He, Xinzhong Wang, Ning Li, Bao Cao, Hongyang Bai, Zhigang Du

Revealing the periodic fracture pattern of the main roof and the key influencing factors of the support resistance is crucial for strata control and support selection of the shallow buried working face with large mining height. Based on the cantilever beam theory, an improved step rock beam model, and the measured strata pressure data of the 12,401 working face in Shangwan Mine, the mine pressure behavior law of the shallow buried with a large mining height working face was analyzed. The results show that both ratio of maximum principal stress to load (σ1/q) and ratio of maximum shear stress to load (τmax/q) inside the main roof increase with increasing periodic advancing distance, while the ratio of maximum shear stress to maximum principal stress (K) is the opposite, indicating that the increase rate of σ1/q is higher than that of τmax/q. K is less than 1 when the periodic advancing distance exceeds 8 m, indicating that the periodic fracture of the main roof will be dominated by tensile failure. Support resistance increases with increasing immediate roof thickness, main roof thickness, periodic fracture step distance of the main roof, and mining height, and decreases nonlinearly with increasing friction coefficient of periodic fracture rock block hinge surface. The main roof thickness, the periodic fracture distance of main roof, and the friction coefficient of the hinge surface of the periodic fracture rock block are the key factors influencing the support resistance. The advance breaking of the main roof and increasing the friction coefficient of the hinged surface of the main roof can reduce the support resistance of the working face. The support resistance of the 12,401 working face in Shangwan Mine presents an arch distribution characteristic. The average periodic weighting step interval, average support resistance, and dynamic load coefficient are 15.6 m, 17,552 kN, and 1.3, respectively. Finally, the rationality and validity of the model are verified by comparing the measured and theoretical values of the support resistance in the 12,401 working face of Shangwan Mine and other shallow coal seams with large mining height.

Apr 22, 2024