Search Documents

By John E. Young

United States Steel Corporation's Winifrede Mine is operated by Lynch District in the mountainous region of Eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slows which present both an opportunity and challenge in the design and selection of coal handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of underground haulage and, thereby, presented the opportunity to use high capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Winifrede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 feet from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede Mine coal handling facilities.

Jan 1, 1970

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By Michael F. Werneke

While the use of synthetic polymers for solid/liquid separation is not raw technology (1)(its history goes back to the mid 1950's), its importance has increased dramatically over the past decade. This can be attributed to two major factors. The first of these was a change to mechanized mining (strip mining and continuous underground miners) which resulted in a lower quality (higher reject) preparation plant feed, as well as a higher percentage of smaller size particles in the feed. The second factor has been the greater restrictions imposed by governmental agencies on effluent discharge and solids impoundment, requiring pre-treatment of recirculating water before reuse and treatment of refuse before disposal. Today, synthetic polymers find utility in almost all applications requiring separation of solids from aqueous suspension, including "in-process" as well as waste treatment applications. In spite of the fact that there are over several hundred commercially different flocculants available in the marketplace (2), there are a limited number of chemically different materials available which are useful from a cost/performance standpoint. The potential reasons for using flocculants in a coal preparation plant are summarized in TABLE 1.

Jan 1, 1979

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By N. Gritzuk

The area of Canada with which we are here concerned consists of Yukon Territory and Northern British Columbia. Generally it lies west of the coastal mountain range and access to the sea can be gained at only selected points which are relatively few. It is served by the Alaska Highway as well as a provincial and territorial system of roads permitting transport of mining products to Whitehorse in Yukon Territory. This town it the northern terminus of the White Pass and Yukon Route, which system provides a rail service between Whitehorse and Skagway, Alaska a distance of 110 miles, and thence to Vancouver, British Columbia, by the coastal Motor Vessel C. J. Rogers, a distance of an additional 890 miles. At present the service between Vancouver, B.C. and Whitehorse, Y. T. is on a fourteen day basis. The coastal vessel, capable of carrying 3,200 tons of cargo, was specially designed and built in 1955 for handling containerized cargo and general cargo northbound, and containerized and palletized asbestos fibre, and palletized lead and zinc concentrates southbound.

Jan 1, 1961

By I. L. Jennings

In most industrialized countries, the largest element of the mining industry in physical volume is that devoted to the extraction and processing of materials for use as construction aggregates. Required for all developments in industry and commerce, power and transportation, and housing and public services, their use is so widespread that possible sources are exploited throughout all geographic regions, as close as possible to the point of use. Thus, it is also the most frequently encountered form of mining throughout the world. These materials come from four main sources:- (a) Excavation of unconsolidated deposits of sand and gravel (b) Stone quarrying. (c) Processing of slags and other mineral wastes. (d) Manufacturing from clays and shales by heat fusion. The major uses are in: (a) Portland cement concrete, that most versatile of construction materials, including the many concrete products in current use. (b) Asphalt cement concrete; widely employed for paving roads, parking lots, airfields, etc. (c) Foundation materials, such as road base, granular backfills, railway ballast, etc.

Jan 1, 1968

By Earle Bagley

In late 1971, the Sun Company, then known as Sun Oil Company, acquired a large surface mineable federal coal lease with the thought that those coal measures within its boundaries would provide a future feedstock of either coal or coal liquification. Our Cordero lease was one of the last Federal coal leases let before the recent decade long leasing moratorium. Because of the tremendous demand for compliance steam coal for the electric power industry, a decision was made to develop the property to serve that market. In 1974, Sunoco Energy Development Company (SUNEDCO), the non- oil and gas energy unit of the Sun Company, began engineering studies for development of the lease. The mine was originally designed at a 12.0 million ton per year capacity. The Cordero Mining Company was formed to mine and operate the property. Construction of the facilities adjacent to the lease began in January 1975. Due to the Sierra Club versus Department of Interior Secretary L. B. Morton suit, work within the lease was delayed until mid-1976 when pre-stripping of the overburden began.

Jan 1, 1982

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By G. S. Austin

New Mexico produced 83% of domestic potash and 27% of domestic consumption in 1992. The potash industry of New Mexico produces sylvite (KCI), langbeinite (K2SO4-2Mg(SO4)2), and artificial K2SO4. Average sylvite grade in New Mexico today is about 14%. The average grade of langbeinite is 8-10% Kp. Commercial potash occurs in the middle or McNutt Member of the Salado Formation (Upper Permian Ochoan Series). The 120-m-thick McNutt Member dips about 1° east and contains 11 of 12 potential ore zones in the Salado. The mineralogy and proportion of clay minerals, up to 7% of the ore, influence optimum milling procedures and ore grade cutoff.

Jan 1, 1994

By Ramkrishna Agarwal

A low grade iron ore is mined underground at Grace Mine using the panel caving method. Most of the development work is located in footwall. The runways for LHD equipments are heavily supported with steel sets on five foot centers. The sets are embedded in two to three feet of concrete. The initial cost of support is one of the largest single costs of production. During the process of ore-win¬ning, supports frequently fail, necessitating expensive repair. There is no systematic pattern to the failure of supports. A rock mechanics program was launched to isolate causes and their relative contributions to the failure of supports. The preliminary results are presented. A typical portion of a runway is instrumented to monitor rock mass movements around the runway and the corresponding response of supports as various mining activities are carried out in the neighborhood. We believe that such a program is a prerequisite to any remedial measure to alleviate pressure problem at Grace Mine.

Jan 1, 1973

By Robert Stefanko

The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given elsewhere (1,2). The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania.

Jan 1, 1969

By Frank Matter

The production of ultrafine slurries and powders is possible with small media made out of Si02, A1203, Fe203, Zr03 or other raw materials due to the fact that since approximately 12 years from now, entirely new machines have been developed which allow to use this small media for the production of ultrafine pigments. Basically we distinguish between two grinding methods which are: A.) Dry Grinding with Air Classification: This method is used for more than fifty years but only since four years this technology is realized with small grinding media. Many problems like cooling, abrasion, control of the media flow, separation media from product, grinding media recycling etc. had to be resolved before it was possible to get in full production with this new system. Hereafter a flow-sheet of such a TRZK mill with an air classifier especially designed to produce end products with a top size between 2,5 and 3,0 micron and with an average particle size between 0,3 and 0,5 micron.

Jan 1, 1983

By Samuel M. Brock

Problems related to strip and auger coal mining have grown with the development of the industry and the economy. New technology has produced equipment that has made mining by surface methods not only highly productive, but potentially highly destructive of water resources and natural environments. On the other hand, growth of the economy has produced an increased demand for clean water, and created new demands for amenity values that natural environments provide. Thus, opposing forces have created conflicts in resource use. And these conflicts have made surface mining highly controversial. Resolving the controversy will require the solving of complex economic and social problems. The essence of the economic problem created by surface mining is that, in the absence of proper regulation, substantial costs resulting from the process are borne by the public rather than the mine operator.

Jan 1, 1968

By Alexander Pomerantsev

In recent years, bucketwheel excavators have found wide application in open pit surface mining not only because of their large production capacities, but also because they easily lend themselves to automation. Krupp, Orenstein & Koppel, Buckau-Wolf, Mechanical Excavator, Lauchhammer, Manufacturers in Eastern Europe designed and installed many models of bucketwheel excavators that can excavate any type of materials, could be used in any climate conditions and for any type of technological schemes in open pit surface mining, (Photo I, II and III)

Jan 1, 1979

By A. Bruynesteyn

Results are presented from a series of tests designed to determine the beneficial effects of the microorganism Thiobacillus ferrooxidans upon the leaching of uranium from a pyritic uranium ore. Minus 1-inch (-25mm) 0.0711 percent uranium containing, pyritic ore from the Rio Algom Mine at Elliott Lake, Canada was leached with lixiviants of various Eh and pH as well as being subjected to a biologically-assisted ferric iron leach. In all cases, the biological leach gave superior extraction. At pH 1.6, the biological leach gave 100.6 percent extraction and the ferric iron leach 69.8 percent. This improvement in extraction is associated with a relatively rapid biological breakdown of the pyritic material, thus liberating uranium mineralization associated with these pyritic materials and regenerating the ferric sulphate lixiviant in situ.

Jan 1, 1981

By Robert A. Westin

Polychlorinated biphenyls (PCBs) are a group of chlorinated chemicals that were used in many different fire resistant hydraulic fluids, heat transfer fluids, and in electrical equipment as dielectric liquids. PCBs were manufactured primarily by Monsanto Chemical Company under the tradename Aroclor, and were used by many different electrical equipment manufacturers. PCBs are noted chiefly for their extreme chemical inertness. This resulted in exceptional fire resistance and long life in applications involving exposure to high temperatures and intense electrical fields. This combination of properties resulted in PCBs being widely used in electrical equipment used in mines, including transformers, capacitors, and some electric motors. PCBs were also used as working fluids in some heat transfer and hydraulic sys terns. The same chemical resistance that gave PCBs long life in industrial applications give PCBs essantially eternal life when they are released into the environment. PCBs are not highly toxic in the sense that exposure does not cause immediate health problems. However, PCBs accumulate in the human body and neither degrade nor are eliminated from the body, and long-term exposure to PCBs can result in changes in liver function which may increase susceptibility to the carcinogenic effects of other chemicals. PCBs also accumulate in the food chain; the concentration of PCBs in fresh water fish may be several hundred thousand times as high as in the water the fish are taken from.

Jan 1, 1981

By N. B. Aughenbaugh

A study was made to determine those petrographic parameters that are correlative with carbonate-aggregate quality as indicated by the Los Angeles abrasion and absorption tests. Samples collected at 28 sites in northern and eastern Indiana were analyzed petrographically, chiefly for void content, grain size, grain-size variation, grain shape, and grain interlock. Most of the sampled sites are in the belt of Silurian rocks of east-central and north- western Indiana. Though a few sites lie outside this belt, most of these have only a thin Devonian section above the Silurian. Three sites are non-Silurian and are included for comparison. Most of the samples studied are from Middle and Upper Silurian units. Both biohermal and nonbiohermal facies are included. The biohermal rocks are typically dense but vugular, finely crystalline granular dolomite. Nonbiohermal facies are porous, medium to coarsely crystalline, granular dolomite with dolomite rhombs The Los Angeles abrasion losses ranged from 20 to 46 per cent, the rocks in the eastern part of the state showing the higher values. Absorption tests indicate the same general quality trend. Comparison of petrographic studies with Los Angeles abrasion- and absorption-test results indicate the following correlations. (1) As per, cent of voids increases, quality decreases. (2) As average grain size increases, quality decreases. (3) Variations from mean grain size appear to have no effect on the quality. (4) As angularity and roughness of the grains increase, quality increases. (5) As grain-to-grain interlock increases, quality increases. Variations in the calcium-magnesium ratio have no apparent effect on aggregate quality, except as they affect the texture.

Jan 1, 1966

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By Da-Rong Chou

An optimum method for selecting exploratory drilling locations has been developed. The process has been modelled as a highly non-linear programming problem subject to constraints. Solution involves an iterative algorithm which converges rapidly and procedures have been developed to distinguish between local and global optima. The algorithm has been implemented as an interactive computer program which allows the user to influence directly the solution process and to evaluate the effect of any manual adjustments to the optimal solution.

Jan 1, 1984

By E. Neumann

With fuel costs unstable but escalating, solid fuels are playing an increasingly larger part in industrial concerns. Coal, petroleum coke and wood are examined from a burner system design viewpoint and from operational experience in kilns, hot gas generators, etc. The burner of today must also handle multi-fuel tasks and allow immediate, painless switching from one fuel to the next as well as the simultaneous burning of two or mope fuels. The paper discusses the principle of burning alternate pulverized fuels as well as the practice both in the United States and around the world.

Jan 1, 1983