Search Documents

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the' variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By Massimo Concilia, Remo Grandori, Paolo Nardone

Paul Y. – SELI Joint Venture had been contracted to build the longest section of the Strategic Sewage Disposal Scheme (SSDS) – Stage I. This involved two tunnels under urban and marine areas excavated by high performance hard rock open type TBMs operated from deep shafts. A specific ground treatment program was developed using advance probing and grouting to control water inflow into the excavations. The article describes: the technologies adopted, the experienced problems, the encountered productions and their interrelation with the water inflow amounts, the possible improvement in the technologies for the excavation of the future stages of the same project as well of any other project under similar conditions.

Jan 1, 2001

By F. D. Wang

This paper presents an innovative mining method with the application of the water jet. The basic principle of this mining method is to mine a thin panel slice with a water jet system and to allow the roof to deflect elastically and subsequently to be supported by the coal floor without artificial roof support. Through the sequential mining of layers from top to bottom, the entire seam is extracted and the roof rests upon the mine floor. The advantages of this method are that the safety of underground operation can be greatly increased and the surface overburden disturbance will be markedly reduced. . An economic evaluation of such a system is presented for the total cost estimated per ton of coal mined at the face. This evaluation is then compared to that of a continuous mining section utilizing a room and pillar mining method.

Jan 1, 1991

By E. C. Watkins

The fiber glass industry is an industry that. hopefully is still in its infancy and far from a mature business. Fiber glass, as will be discussed in this paper, deals with continuous strand glass as used in the textile laminate and reinforced plastics industries. More specifically, we are speaking of glass used for printed circuit boards, tapes, paper, cloth, pipes, tanks, boats, recreational equipment, roofing shingles, and automotive applications. Compared to the flat, container and decorative glass industries, we are very young. The early patents on fiber glass applications were issued in the 1930's. The type of glass most commonly used in the world and that discussed in this paper is designated as "E" glass. This is a boro-silicate type glass having specific chemical and electrical resistance and low thermal expansion properties.

Jan 1, 1986

By W. Edwin Dill

For the mining industry, the Internal Revenue Code and regulations offer a range of choices in arriving at the allowable depletion. Each case is essentially unique. Two prerequisites can optimize these opportunities: communications between the mining company's tax specialists and its technical staff; and an understanding of IRS definitions. For the latter, a logical starting point is consideration of exploration and development, since they precede production and depletion is unallowable prior to production. Criteria for selecting engineering and accounting options for exploration and development indicate the necessity of interaction between these company functions to achieve the most favorable tax position.

Jan 1, 1982

By Ernest Bohnet

Each mining operation is unique in some aspect ownership; ore body location, size, geometry, grade, mineralogy, hydrology, or geotechnical parameters; or constraints such as environmental regulations. However, all mining operations are alike in one aspect; the prime objective of any mining project is to maximize the return on the investment. This is the golden rule, or in the language of mining, the investor?s law of conservation. A mineral resource, by definition, does not become a minable reserve unless the mineral or minerals can be extracted economically (and legally). The three preceding sections have covered the various types of surface mining options. The choice of the most economic method is dictated primarily by the type of de-posit to be mined, the mining rate, and the physical characteristics of the deposit.

Jan 1, 2008

By A. L. Slaughter

A mineral deposit has been discovered and explored sufficiently to establish the presence of ore in ?commercially marketable quantities," This is the point at which exploration ends and development begins, Of course, when the presence of commercially marketable quantities of ore are thought to be present the deposit had to be evaluated before this decision could be reached. If, on the other hand, it was thought that commercially marketable quantities of ore are not present, either more exploration has to be done or the project must be abandoned. It is this decision with which this paper is concerned, more particularly, the influencing factors behind this decision. The final question to be answered is: what profit can my company reasonably expect to make by developing this property and putting it into production? The answer must be expressed as a figure for final profit per ton, money which can be used to pay dividends or to build up cash reserves. Some acquisition cost has probably been paid and the exploration cost incurred at the time of decision, (abandonment or development). In addition to returning these acquisition and exploration costs, the deposit must pay development, mining, milling, capital expense of new plants and equipment, taxes, and various other related costs.

Jan 1, 1958

By William N. Poundstone

Since World War II, when off-track mining became popular, mining machinery has undergone much change. However, the change has been basically to make the machines more powerful, more productive and more reliable. Little change has been made, in this period, in the basic mining system. While steady improvement was made in productivity until the passage of the new Federal Coal Mine Health & Safety Act, I believe that the cost Co benefit ratio of further improvement from this basic approach of improving the existing extractive tool is not as promising as I believe may be obtained from a new approach. Consequently, six years ago Conoco and Consol undertook a comprehensive long-range R&D program to see if improvements of a more basic nature could be made in underground mining. We concluded early in our program that while many things currently limit the rate of production such as the rate at which roof can be supported, time needed to advance ventilation systems, time required to clean up and rock dust, time required to maintain and service equipment as well as time lost due to haulage deficiencies, that the key to improvement was a truly flexible continuous high capacity haulage. With face equipment in use today, mining rates can be increased with such a haulage system where the ability to support the roof exceeds the ability of conventional haulage equipment to remove the coal. More importantly, if we could develop such a system, it would set the stage for development of far more sophisticated methods of mining at the face than exist today, and as new and more dependable mining machines and methods are developed, continuous transportation will enable the gains envisaged in production to be realized.

Jan 1, 1974

By S. S. Wang

Dialkyldithiophosphinates are a new class of flotation collectors for base metal sulfide ores. Structurally, they are quite different from the conventional collectors such as mercaptans, xanthates, thionocarbamates and dithiophosphates. Collectors Structures [Mercaptans R-SHS Xanthates R-OCS-M+ Thionocarbamates R-OCNH-R Dithiophosphates 2 R-CCNH-R' Dithiophosphinates (R) 2-PS-M+ ] In the above structural formula, R and R' stand for a hydrocarbon radical, and M+ is an alkali metal or ammonium cation.

Jan 1, 1982

By R. E. J. Putman

Rising demand, artificial market conditions, increased overseas competition, and a fluctuating international situation have brought ever increasing pressures to bear on the nonferrous metals industries, and particularly in the United States, Although capacity is being expanded by the construction of new plants and the development of new ore deposits, increasing attention is being focused on the possibilities of improving the performance of the existing installations and of getting the most out of the new equipment now installed. At first sight the task appears formidable. Based on raw materials which are nonhomogeneous, and possessing characteristics which are hard to quantify, even the processes by which the values in the ores are concentrated and extracted are in many cases not fully understood. The necessary analytical equipment and transducers demanded by these industries have also been slow in development and their earlier absence has hampered the application of modern control technology, This is reflected in plants which have been designed for ease of manual rather than automatic control, and in which the application of control techniques at first sight appears economically prohibitive. However, in any industry progress often comes only in small steps, It may be that by the wise choice of limited objectives and perhaps only partial solutions, substantial improvements in plant performance can be implemented now, and with only a modest investment. If modern control equipment is chosen of the type which can be reprogrammed, advantage can be taken later of more sophisticated solutions as the technology of the industry advances. This task of improving plant performance can and must be commenced even though our knowledge is incomplete. The experience of a related mineral consuming industry, with similar problems in the past, can be encouraging.

Jan 1, 1967

By Glenn J. Phillips, Debra L. Musick

The operating mine is dynamic, everchanging, and a continuous moving target. The only way to effectively manage such a creature is to be able to evaluate the cost of operation over short enough time periods that rapid effective controls can be implemented before loss can erode the marginal profits in todays market place. Such short term evaluations can provide the basis for the long range planning that can keep an operation healthy in the future. The spreadsheet programs on small computers (PC's) offer the possibility of such evaluation by accumulating data in a useable format, providing timely cost reporting and providing a tool for use in evaluating the day to day alternative choices of the real mining world.

Jan 1, 1987

By William G. Schultz

Sylvite of Canada, a wholly owned subsidiary of Hudson Bay Mining and Smelting Co., operates an 8000 TPD potash mine and refinery located nine miles North East of Rocanville, Saskatchewan. Prior to Hudson Bay's entry in 1968 into potash mining and refining, it was one of the more traditional and conservative Canadian Mining Companies whose principal business had been for many years a successful copper-zinc mining and smelting operation located at Flin Flon, Manitoba. The potash reserves being mined by Sylvite were acquired through the acquisition of Francana Oil and Gas. This acquisition was at the time when several major potash mines were being developed or had recently been brought into production in the Province. These mines are owned by either very substantial Canadian Mining Companies or Multi-National Mining Companies with considerable potash mining experience. At that time, it became very apparent because of the new mines coming into production, potash mining and refining would quickly become a very competitive industry. Because of long term considerations, Hudson Bay decided to proceed with the development of its potash reserves, recognizing the Mine and Refinery would have to be the most advanced available in order to successfully operate. This report deals with the mining operation at Sylvite and the degree of success Sylvite has achieved.

Jan 1, 1972

By Jeffrey A. Holcomb

INTRODUCTION The passage of Comprehensive Environmental Response Compensation and Liability Act (CERCLA/Superfund) as well as the Resource Conservation and Recovery Act (RCRA) and state laws, have placed added regulatory pressures on the mining industry. These laws which focus on the regulation of hazardous substances and wastes for the protection of the public health and welfare and the environment, present the potential for tremendous financial impacts and liabilities on existing mine operators and owners and/or potential mine operators/owners. This paper takes a brief look at these laws and presents an environmental audit procedure to identify environmental liabilities prior to mine land transactions. The environmental audit approach presented is an overview of the procedures that could be used to document, evaluate and inventory existing and/or potential environmental concerns. This audit procedure can be applied to developed or undeveloped properties and at active or inactive mining sites. REGULATORY OVERVIEW Mining environmental liabilities have been addressed in RCRA, Superfund, the Clean Air Act (CAA) and the Clean Water Act (CWA). Even though the U.S. Environmental Protection Agency (EPA) has determined that mining wastes will be treated as solid wastes under RCRA and not as hazardous wastes, these wastes could still bring about a great deal of financial liability under Superfund. The catch is if the mine wastes generated contain hazardous substances such as the heavy metals arsenic, beryllium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, thallium, zinc and others as well as cyanide. Thus, it is not only important for a mine operator/owner or a potential mine operator/owner to know if the mine wastes generated are hazardous, but it is important to know if the wastes contain hazardous substances. Following is a brief overview of RCRA and Superfund and their potential implications. RCRA RCRA, which provides the basis for the regulation of solid and hazardous wastes, is applicable to active mining and milling sites. Within RCRA the definition of a hazardous waste is provided. This definition applies to owners and operators of mining and milling sites if the operator has stored, disposed or treated hazardous wastes on-site. If this is the case and if strict process control and waste management activities are not adhered to, environmental liabilities may be associated with the site. Superfund The 1980 Superfund law can be applicable to inactive mining sites or to inactive sections of an active facility. The provisions of Superfund call for the regulation of hazardous wastes and hazardous sub- stances disposal and release not only by the existing owner, but also for any previous owner. This concept of joint and several liability means that one party, as among many, can be held totally responsible for the costs of hazardous waste cleanup (Haller, 1987). Furthermore, liabilities under Superfund have also been applied back to past acts; thus, several mining properties, active or inactive prior to the 1980 Superfund law, are at risk of being placed on the EPA's National Priority List (NPL) for cleanup. Last years amendments to Superfund, known as the Superfund Reauthorization Act of 1986 (SARA), provided some significant developments for the mining industry. The major requirement of the amendments as it pertains to owners or operators of mining sites is that the EPA must revise its present Hazard Ranking System (HRS). This is important be- cause in most cases the primary reason for several mining sites having been included on the NPL was due to the large volume of wastes generated. As is typical at most mining sites, large volumes of low toxicity wastes are generated and the current HRS model prejudices against this. It should be noted that this provision only applies to sites that are not already on the NPL or have not been proposed for inclusion on the list.

Jan 1, 1987

By M. T. Webster

Views about the proper aim of public policy are, of course, matters of perspective and debate. Regardless of perspective, one would assume some consensus around the view that public policy ought to encourage mine operators to seek independent and critical assessments of worker safety and health at their operations through voluntary auditing. However, a review of the law on this topic shows that there is little to no manifestation of such a policy. Indeed, the balance of this paper, with a couple of exceptions, is devoted to the existing legal pitfalls that should be considered before a safety and health audit is conducted at a mine. While attorneys, particularly litigators like the author, might tend to focus on the potential problems that could arise from any given situation, the fact that most of this paper is devoted to potential legal concerns associated with auditing is a realistic reflection of the current state of the law. Specifically, this paper addresses the interplay between voluntary safety and health audits conducted at mines regulated by the Mine Safety and Health Administration (MSHA), and the administrative and civil legal issues related to such audits. The paper first provides an explanation of how and by whom an audit is conducted. The paper also addresses whether voluntary safety and health audits may be considered privileged and kept confidential in administrative and civil proceedings. Finally, selected legal issues related to such audits that could arise in administrative and civil litigation are discussed.1

Jan 1, 2012

By Stephen Utter

This report summarizes the results of preliminary investigations concerning the influence of block caving mining upon adjacent mine openings and discusses possible methods for reducing critical rock pressures and damage to these openings. These investigations are one part of a general study of the rock mechanics of block caving by the Denver Mining Research Center of the Federal Bureau of Mines. The purpose of this part of the study Is to obtain an estimate of the stress concentrations around mine openings adjacent to block caving stopes for use in developing better designed openings and improving mining methods. When mine openings such as slusher drifts, grizzly drifts, and haulage drifts are damaged by rock pressures induced by block caving mining, the mining cost increases, mine production decreases, and ore recovery may be consider- ably lessened. Methods of mining that result in lower rock pressures and methods of design that enable mine openings to withstand these pressures are desirable. The development of these methods, in turn, requires a fuller understanding of the following: The stres concentrations around the mine openings and the changes in stress induced by adjacent mining; the physical properties, such as the compressive strength and modulus of elasticity of the rock surrounding the openings; and the support supplied by the concrete lining, timber sets, or other types of supports used in the openings.

Jan 1, 1962

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By B. S. Pierce

The National Coal Resource Assessment – 2000 project was a multi-year effort by the U.S. Geological Survey to identify, characterize, and assess the coal resources that will supply a major part of the Nation’s energy needs during the 21st century. The purpose of the USGS National Coal Resource Assessment (NCRA) was to (1) digitally assess selected coal beds and zones that will be the most important in the next few decades, (2) create publically available stratigraphic, geochemical, and geographic information system (GIS) databases to answer a variety of questions of importance to government, industry and public decision makers, and (3) provide interpretive geologic and geochemical information for the primary coal resources of the Nation. Five priority regions were assessed: the Appalachian Basin, Illinois Basin, Gulf Coast, Illinois Basin, and Northern Rocky Mountains and Great Plains. The NCRA was a cooperative effort between the USGS and a number of State geological surveys in these coal-bearing regions. A study of coal resources on Federal lands was also conducted. Adequate energy supplies and the efficient use of those supplies are critical to the economic well being of a country. Affordable and reliable coal supplies are essential to the interests of our national and local policymakers. Policy makers require a range of information on the energy supply, as well as the economic and environmental issues associated with that energy source and its use. Formulation of an effective national energy policy and development of energy resources requires that we understand the geology, distribution, quality, and size of the national energy endowment.

Jan 1, 2001

By Brian W. Mackenzie

The mine development decision is made on completion of exploration to determine whether or not a mineral deposit should be developed to production and, if so, how. This involves the selection of an optimum mine development alternative from a number of technically feasible alternatives and the comparison of this optimum with those of other available investment opportunities. If the optimum is sufficiently attractive, the deposit is developed to production. The selection process is carried out within a framework of corporate objectives and resources. The mine development decision is based on the balancing of two parameters - - rate of production as reflected in plant capacity and cut-off grade. On the basis of available information and experience, detailed revenue and cost 'estimates are made for each feasible combination of plant capacity and cut-off grade. What economic evaluation techniques should be applied to these estimates to reduce each alternative to economic indicators that will enable meaningful comparisons and an informed investment decision? This is the essence of the paper. The determination of optimum plant capacity and cut-off grade has been the subject of intensive research efforts by economists and mining engineers (1-7). Their studies are based on marginal analysis and assume that, at the time of decision, certainty conditions prevail with respect to ore reserves, mining costs and mineral markets. The optimum mine development alternative is defined as that which maximizes profitability.

Jan 1, 1969

By W. L. Price

The intelligent selection of wire cloth and perforated plate for screening surfaces seems a rather confusing subject to the newcomer in aggregate processing. The proper application of various screening surfaces is a complicated one and one could consider himself an expert only after many years of working with all applications. However, part of the subject matter could be simplified considerably for, the average screen user. In this paper an attempt will be made to do this, by presenting some comparative specification data along with cost figures Unfortunately, it is impossible in the limited scope of this paper to give actual service comparison records between different cloths or cloth and plate. Anyone who has considered making actual service comparisons for competing screening media is well aware of the almost insurmountable problems Their solution would form the basis for a separate paper on that subject alone. Therefore, this paper will be limited to comparative data up to the point of installation.

Jan 1, 1961

By A. W. Khair

This paper deals with the causes and mechanisms of pillar failure in a southern West Virginia coal mine. The conclusions are based on in-mine observations and analysis of mining methods, eyewitness account of the sequence of events, topographic and geologic conditions, and mechanical properties of mine roof, coal, and floor. The study indicated that massive pillar failure was caused by the collapse of the mine roof. The collapse of the mine roof was due to the combined effects of high lateral compressive stress and high extraction ratio causing excessive bending of the roof beyond its limit. It was assumed that the higher lateral compressive stress under such a shallow cover was probably due to the drastic change in the structural geology of the area and possible residual stresses. Eased on the analytical study it was concluded that the sudden release of elastic energy (shock) due to the rupture of the roof caused the squeezing of approximately eighty mine pillars.

Jan 1, 1983