Search Documents

By John L. Schroder

The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same seam in nearby properties. Such mines may indicate in advance much about roof control, drainage, ventilation, and other mining problems.

Jan 1, 1981

By William M. Greenslade

As the search for minerals leads to deeper mines the need to control water inflow into mine shafts and mine workings will grow. As shal¬lower more readily available minerals are exploited, ore bodies which were previously uneconomic be cause of their depth will now become attractive targets. In known mining districts new ore bodies are being discovered down dip of existing ones. In the west many metal deposits are being developed in rocks of the mountain front pediments, frequently covered by several hundred feet of saturated alluvium. Greater depth often means that workings are developed well below existing water tables, creating high hydrostatic heads adjacent to mine workings. The purpose of this paper is to review some of the methods available for determining if water control will be necessary and to present some of the techniques for locating water bearing zones and the amount of water to be expected. The paper will concentrate on problems associated with water control in mine shaft development, although many of the exploratory techniques are similar to those needed for assessing overall mine water inflow problems. A brief case history on water control problems in mine shafts in the Grants mineral belt of northwestern New Mexico is presented. Water control during shaft sinking presents some unique features. First, the problem is a relatively short term one, since water control is often necessary only while the shaft is being sunk. Control measures may be necessary only while the shaft is open into the water bearing zone and the lining installed and cemented. Secondly, limited working space within the shaft area presents difficulties in handling large amounts of water inflow. The presence of water in the shaft working area increases sinking time and the potential hazard to miners. Finally, there is the economics of shaft sinking. While the shaft is being sunk no ore is being produced and there is every incentive to minimize costs.

Jan 1, 1979

By Ibezim J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous content and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, Alabama and FMC Corporation in Pocatello, Idaho were investigated using physical separation techniques to recover the elemental phosphorous in the sludge and to render the residual material non-hazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69 -90% P4 with a recovery in the range of 60 -87%. Dispersed air oxidation of the fines and tailing products was effective in removal of an additional 10 -15% of the P4 in the sludge.

Jan 1, 1991

By J. S. Wozek

In metallurgical applications, coal fulfills dual roles as a chemical feed stock and as a fuel source. These applications range from cokemaking, ironrnaking (including pulverized coal injection), foundry, basic oxygen furnace / electric arc furnace coal additions, direct ironrnaking, Corex, and the futuristic direct steelmaking. In all steelmaking related processes, chemical reactions are simultaneously temperature and chemical dependent. Therefore, coals used in these processes must consistently comply with specific quality parameters in order to promote efficient operations. This paper limits discussion of Metallurgical Coal Quality to cokemaking and ironmaking applications. Its purpose is to present the customer's perspective on the control of critical coal and coke properties.

Jan 1, 1994

By Jr. Moulton

Extractions of minerals from Searles Lake brines have taken place since 1873. Early operations were for borax and raw trona found on the surface, expanded after 1914 to include potash, salt cake, and soda ash. A new soda ash plant now in operation will double area production. The evaporite beds were formed by desiccation of Eastern Sierra runoff. The resulting series of brine-bearing salt beds supply the fluids necessary to feed the area chemical plants. Production methods include evaporation and crystallization for potash, borax, and salt cake; carbonation of brine to recover soda ash; and organic extraction of borax.

Jan 1, 1980

By Dal Negro Enrico, Andrea Picchio, Boscaro Alessandro

"The Doha Metro Project is one of the most relevant ongoing tunneling projects. The whole project consists of about 100 km of tunnels with 21 EPB TBMs working in the same period. Due to the variability of the geological formations, the soil conditioning is a relevant aspect of this project because the parameters should be frequently adjusted to achieve the best performances of the TBMs. The study of the soil conditioning has been carried out accurately to obtain the best results on site. The study of the geotechnical data, the choice of the most suitable foaming agents and polymers and the laboratory study of the soil conditioning has been a fundamental part of the job. The application of the soil conditioning products on site with the analysis of the TBM data have confirmed the preliminary study results with some correlation between the features of the ground and the soil conditioning parameters to be used. INTRODUCTION Phase 1 of the Doha Metro Underground project is composed by 3 lines able to bring passengers to all the points of interest in the Qatar capital city. The Red Line, also called coastal line, connects the north of the city to the south, and to the new Hamad International Airport, following the coast line. The Golden Line, called Historic Line, will connect the southern area of Doha to the “Aspire zone” the area of the city where many state of the art sport centers are located, passing through the old city center. The Green Line, named education line, will connect the old city center to the Doha Education City. All the lines are realized with 2 tubes, single track. The whole underground project is realized with 21 TBMs, excavation diameter of 7.10 m. The project has been divided in 4 packages, for a total excavation length of more than 100 km. The need to underpass roads, existing buildings, and to excavate, in some areas, at less than 100 m from the coast line, forced the choice of a tunneling system with Earth Pressure Balance (EPB), that involves in the project another fundamental aspect of this tunneling system: the soil conditioning. The soil conditioning has multiples functions in the EPB system such as to make the soil suitable to properly apply the pressure on the tunnel face and to be extracted effectively with the screw conveyor. To properly study this topic it was necessary to study the geological formations to be excavated, the hydrogeological conditions of the underground, the foam injection systems of the EPB TBMs and to perform specific tests to evaluate a suitable conditioning to be verified and adjusted during the real scale application."

Jan 1, 2016

By Palmer C. Sweet

Kyanite. andalusite, and sillimanite are anhydrous aluminum silicate minerals, and they have the same chemical formula, Al2SiO3. Dumortierite and topaz are also classified as aluminum silicates although they contain boron and fluorine respectively. Mullite (a rare mineral named for its discovery site, the Scottish island of Mull) is produced when kyanite, andalusite, or sillimanite are heated. Synthetic mullite, also classified as an aluminum silicate, is formed by melting alumina and silica, bauxite, and kaolin or alumina, kaolin, and kyanite, depending on the type of synthetic mullite desired. These materials are either sintered in rotary, periodic, or tunnel kilns, or fused in an electric arc furnace. The world's largest producer of kyanite is the United States. Domestic kyanite is presently produced from one company at two sites in Virginia; Kyanite Mining Corporation mines kyanite from Willis Mountain and adjacent East Ridge in Buckingham County in the central Piedmont province of Virginia. Internationally, kymite is produced in Australia, Brazil, India, Kenya, Sweden, and Zimbabwe; the former USSR also produces kyanite (Fig. 1). Andalusite is produced by Piedmont Minerals Company, Inc. in the Piedmont province near Hillsborough, NC. Andalusite is also produced in France, India, the Republic of South Africa, and Spain (Fig. 1). Sillimanite is produced in Australia, Brazil, India, Spain, and the Republic of South Africa; the former USSR is also thought to be a major producer (Fig. 1). Some of the countries produce only for domestic use. Synthetic mullite, made by sintering and by electric arc fusion, is produced by Mulcoa (Mullite Company of America) in Andersonville, GA, and by Washington Mills Electro Minerals Corporation in Niagara Falls, NY. Annual world production of kyanite, andalusite, sillimanite, and synthetic mullite is approximately 672 727 tons (Potter, 1988). GEOLOGY Mineralogy Kyanite is a blue to light-green, triclinic mineral that occurs in long, thin-bladed crystals and crystalline aggregates in gneiss, schist, and pegmatites. The mineral has a hardness of 5 parallel to the long axis of the crystal and a hardness of 7 across the crystal. Andalusite is a yellow, brown, green, or red orthorhombic mineral that occurs in thick, almost square prisms in schist, gneiss, and hornfels. Gem quality andalusite exhibits a strong pleochroism; brownish-green in one direction and brownish-red perpendicular to it. Andalusite also occurs in placer concentrations where it has weathered out of rock. Sillimanite is a brown, pale-green, gray, or white orthorhombic mineral that occurs in long, slender, needlelike crystals in schist and gneiss. Chemical and Physical Properties Chemical and physical properties of kyanite, andalusite, and sillimanite are noted in Table 1. Kyanite is the only mineral that irreversibly expands when heated (calcined to produce mullite) and may offset the shrinkage of most ceramic or refractory ingredients when heated.

Jan 1, 1994

By A. L. Anderson, J. T. Rybock

KEECO has developed the Silica Micro Encapsulation (SME) technology for the treatment of acidic, metal-laden waters. Utilizing a silica-based chemical formulation that entails chemisorption and micro-encapsulation of heavy metals in a permanent silica matrix, encapsulated particles settle quickly and are effectively isolated from the surrounding environment, producing a stable sludge that is characteristically non-hazardous. In a number of independently-verified pilot and full-scale applications (including the Bunker Hill Mine, Leviathan Mine, Wheal Jane Mine, and Meldon Quarry), SME has been proven highly effective. The technology has been featured in a number of mining publications and selected for innovative technology awards.

Jan 1, 2000

By P. Bester, G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26million tons of ore of which 16 million is mined and milled onsite. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centred around the Pyroxenite ore. This will lead to substantial increases inproduction costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

By Richard H. Johnson

White Pine Copper Company, a subsidiary of Copper Range Company located in Michigan's Upper Peninsula, mines a Precambrian sedimentary deposit containing finely disseminated chalcocite, native cop- per and native silver. Silver occurs predominately in certain strata and presently provides a mill head averaging 0.25 ounces per ton. This technical publication traces the development of silver recovery at White Fine beginning in early 1961. White Pine refined copper contains an excess of silver over and above that required to impart Lake Copper properties. The copper does not require electrolytic refining to meet industry purity requirements, nor is there sufficient silver to justify electrolysis.

Jan 1, 1970

By F. J. Klingler, R. Hausmann, K. M. Swaffar, J. C. Neyer

This paper presents the results of a study of case histories of projects on which sinking caissons were used to construct shafts for tunnel construction and other underground works. Design methodologies are reviewed with respect to the impact of soil and groundwater conditions on the performance and constructability of sinking caissons. Factors which have led to success or failure are reviewed and evaluated, and recommendations for future investigation, design and construction activities are presented. Cost data for five recent projects are reviewed and compared to the cost of shaft installation by other means.

Jan 1, 1997

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By T. O. Llewellyn

The Bureau of Mines, U.S. Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8 to 10.2 percent P205 and 1.7 to 1.8 percent MgO. Chemical analyses of sized fractions indicated that no pebble concentrate (plus 1.2 mm) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid-fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0 to 31.3 percent P205 at flotation recoveries ranging from 72.4 to 96.1 percent of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36 percent. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3 percent P205 and 0.55 percent MgO could be produced with a flotation recovery of 89.9 percent. The MgO content of concentrates obtained from the Manatee No. I and Hardee samples was 1.20 to 1.36 percent, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 percent, but with a concomitant loss in phosphate recovery.

Jan 1, 1983

By Rodolfo V. de la Cruz

The broad front concept is based on the principle that gasification can be achieved more efficiently and completely from a plane broad combustion front in contrast to other geometries obtainable with current methods of gasification. By restricting combustion to a plane broad front, the ideal condition for gasification is achieved. A plane broad combustion front can be developed in coal by initiating and propagating combustion from the walls of an oriented channel and collecting product gases from another similarly oriented channel. Flow will then be directed along the highest permeability of the coal bed, the available cross-sectional area for fluid flow is substantially increased and, more importantly, the increased flow will be uniformly distributed throughout the whole mass of coal. The success of the method is greatly dependent on how well an initial and rigorous permeability survey and associated corrective measures yield a well-characterized coal bed. To maintain uniform reaction rates, the advance of the combustion front is located with pressure- or mass flow-transducers. These sensors are then connected to servo-controlled mufflers for controlling segments of the fire front which are advancing ahead of others. Finally, the development of the concept to overcome problems of roof collapse, reactant and product gas leakages, and water invasion are briefly summarized.

Jan 1, 1976

By Charles R. Boardman

Recent underground nuclear tests in tuff, alluvium, salt, and granite have yielded data essential to the evaluation of mining applications of contained nuclear detonations. The data indicate that for these media the cavity radius is predictable within ±20% without regard to the properties of the rock in the immediate shot environment. Properties of the chimney of broken rock resulting from collapse of the cavity, on the other hand, are found to be related to the properties of the rock and its preshot structural weaknesses. Seismic effects and radioactivity distribution are sufficiently documented to serve as a basis for predicting the safety conditions associated with detonations for a variety of yields.

Jan 1, 1964

By Edwin A. Harre, John J. Mortvedt

Plants obtain nutrients from both air and soil. They absorb carbon dioxide mainly from the air, although some carbon dioxide may be dissolved in soil water which is absorbed by plant roots. Carbon dioxide, a gaseous form of carbon and oxygen, supplies the carbon which usually makes up 50% or more of plant structure. Growing plants use water more than any other biological substance. Plant nutrients dissolve in soil water and enter the plant via root absorption. Water is then given off into the air as the plant breathes or transpires. Water also supplies hydrogen and oxygen to plants. Plant roots absorb nutrient cations or anions by contact exchange with soil clay particles. Inorganic or mineral nutrients essential to plants are supplied through the soil. Inorganic or mineral composition of plants usually is less than 5% of their weight. In most crop-growing areas, much of this nutrition is inadequately supplied from soil reserves and must be provided by fertilizers. The role of the fertilizer industry is to provide economical, efficient, good quality fertilizers to improve or maintain soil productivity for optimum crop production. The essential plant nutrients other than carbon, hydrogen, and oxygen which often must be added to soils or plants are categorized as primary nutrients (nitrogen, phosphorus, and potassium), secondary nutrients (calcium, magnesium, and sulfur), and micronutrients (boron, chlorine, copper iron, manganese, molybdenum, and zinc). These classifications are based on quantity of nutrients utilized by plants and do not imply their function or degree of necessity. One point of major significance to the fertilizer industry is that not all fertilizer minerals contain the plant nutrients in a chemical form available to the plant. A product which may be considered a fertilizer mineral may require substantial processing or treatment before it becomes useful as a nutrient source or fertilizer.

Jan 1, 1994

By Robert E. Ennis

The somewhat misnomered "continuous" face section is in most mines today still far from perfect continuity. Achieving uninterrupted flow of coal from the mining machine to the outside has been a long sought for goal. Clearly, the largest problem to be solved in continuous mining today is one of increasing the cutting time of the miner. Full machine utilization can never be achieved with the new high capacity miners, as long as their performance is tied to that of the shuttle car. Figure No. I illustrates the point at which shuttle car haulage distance determines unit productivity rather than the productive capacity of the miner. Continuous mining is never realized. A recent development has proven, however, that truly continuous mining and haulage is possible. The Bell & Zoller Coal Company working with the Research and Development Department of Hewitt-Robins Inc. developed and perfected a new mining system which offers advantages in terms of increased productivity at reduced mining costs and enhances the safety of personnel at the face. This new system involves the use of two pieces of equipment that form a unbroken link, at all times, between the mining machine and the mine belt haulage system. These pieces are a Mobile Bridge Conveyor, and an extensible panel conveyor. The following areas of discussion will be covered during the review of this development. I. The design and operating features of the new system. 2. Its application in underground mining 3. The performance of the system to date 4. Operation and maintenance cost considerations 5. Safety features of the system

Jan 1, 1965

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By Thomas C. Atchison, James J. Olson

INTRODUCTION Technologic progress depends on new and innovative ideas, the practical application of these ideas, and finally as the technology is developed and demonstrated, the engineering improvement or replacement of existing capabilities. In many areas the new ideas, although known, are not immediately put to practical use in all applicable fields. Good technologic forecasting for research and development within the excavation field coupled with adequate technology transfer is necessary to ensure timely application of innovative ideas to remove bottlenecks in the total system. The purposes of this paper are (1) to show the potential ability of technologic forecasting to meet future demands in rapid excavation through the acceleration of excavation rates by research and development in several related technologic fields, (2) to provide a brief review of the initial development of the ARPA (Advanced Research Projects Agency) Rock Mechanics and Rapid Excavation Program, (3) to draw attention to the research projects completed or underway in the FY 1970-1972 ARPA program and explain where information or program results can be obtained, (4) to summarize the progress and accomplishments of applied research contracts in the rock disintegration element of the ARPA program, and (5) to discuss the research directions planned for the remaining years of the program. The Advanced Research Projects Agency (ARPA) is a group within the Defense Department responsible for conducting basic and applied research and development for advanced projects assigned by the Director

Jan 1, 1997