Search Documents

By L. R. McCullough

To compete in Today's Market, Mine Managers have two, often conflicting tasks. They are to improve productivity, allowing the mines to compete in our world markets and to improve the environment in which our miners must work. To Maintain and improve the environment to ever increasing acceptable levels requires monitoring. In years passed this required considerable labor, which was provided by the Ventilation Department. They continuously took manual samples using hand-held instruments, sampling gas level such as CO for fire and methane for explosive risks. In addition they took continuous air velocity readings with hand-held instruments which allow them to calculate the ventilation air movement in each area of the Mine. This manual gathering of information was not only expensive and slow but marginal at best. It was marginal because the gas sampling was sporadic rather than continuous, as sample reading taken in one part of the mine would likely not be repeated for another 8 hours. If problems did occur, they likely went unobserved until they reached crisis proportion.

Jan 1, 1990

By Stanley V. Lachmansingh

Bauxite can be regarded as a mixture of hydrated aluminium oxides the predominant constituent - and oxides of iron and titanium, silica and silicates. Heterogeneous and non-crystaline, most bauxites vary in average composition from one deposit to another both in terns of impurities as well as the proportion of Gibbsita and the Monohydrates Diaspore and Boehmite. Iron levels (as Fe2O3) can vary from less than 1% to as high as 30% with the alumina content ranging from 40 to 6o%,. Gore than 90% of all bauxite mined in Guyana is used as feed for the - production of refractory grade calcined bauxite. There are -however, several speciality grades used in various industrial applications and these are characterised by the quality of the bauxite in particular ;,with regards to iron and silica levels which generally have to be low. The main speciality grades are designated Refractory, Abrasive and Chemical. Bauxitte is also used in the production of nigh alumina cements,, activated bauxite end in the manufacture of electrical insulators.

Jan 1, 1977

By K. G. Wallace

In 1982, the US Congress passed the Nuclear Waste Policy Act (NWPA) to provide for the development of an underground repository for spent nuclear fuel. This development will be managed by the US Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository. Those sites were: (1) a site in volcanic tuff located at Yucca Mountain in Nevada, (2) a site in bedded salt located in Deaf Smith County in Texas, and (3) a site in basalt located in Hanford, WA. At present, conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation system designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be reestablished to allow reentry into previously closed rooms for the purpose of inspection, maintenance, or retrieval.

Jan 1, 1988

By Peter I. Brooker

The semi-variogram, the basic tool of geostatistical estimation procedures, must itself be estimated from the available data. From a numerically simulated two dimensional deposit, with known variability expressed through its semi-variogram, the standard arithmetic mean estimator is used to calculate experimental semi-variograms. These are determined on a series of data sets obtained from the deposit with various sampling grids which cover different areas of the deposit and which have a wide range of available data. The orders of discrepancies between estimated and theoretical semi-variograms are determined in this idealized situation; and this provides a basis against which to assess experimental semi- variograms made on field data.

Jan 1, 1982

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By C. E. Jordan

The Tuscaloosa Metallurgy Research Center of the Bureau of Mines, U.S. Department of the Interior, is investigating the recovery of phosphate from beneficiation slime, as part of the Bureau's efforts to conserve mineral resources through increased use of wastes. Phosphate equivalent to about two-fifths of U.S. production is discarded annually in the wastes. Exploratory flotation tests on the plus 5-um fraction of a slime sample showed promise for a classification-flotation technique. Onsite classification tests at six phosphate washing plants were conducted with a two-stage hydro cyclone system designed to recover the plus 5-um material. The cyclone underflows contained 8.3 to 19.1 percent P2O5, and the recovery of the plus 5-um PZOS values ranged from 81 to 95 percent. The percent P2O5 recovery from the total slimes ranged from 38 to 47 percent. Batch-flotation studies are currently being conducted.

Jan 1, 1978

By G. Deschenes, W. Yen

Ammonium thiosulphate is a non-cyanide lixiviant for gold leaching. The major problem is the high reagent consumption. A combination of 0.3M (NH4)2S2O3, 0.03M CuSO4, 3M NH3 was used to leach a copper-bearing gold ore at pH 10.2 for 24 hours. 30 kg/t of thiosulphate was consumed. Oxygen and copper species were found to be responsible for thiosulphate decomposition. The thiosulphate consumption could be reduced to around 17 kg/t by adding chelating agent, reducing copper sulphate concentration to 0.001 M and replacing CuSO4 by NiSO4. The increase of pulp density might reduce the thiosulphate consumption to around 17 kg/t. By regulating the oxygen supply, the thiosulphate consumption could be reduced to 10 kg/t.

Jan 1, 2002

By Earle Faig

Along with other transportation modes, the barge industry will be greatly effected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events have caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of our long experience in moving large quantifies of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to the barging industry. Barge companies operate on a 40.23-Mm (25 000 mile) river system which includes the East and West Coasts and the Mississippi River System. Included in the Mississippi River System are the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior - Tombigbee and Mobile Rivers as well as some smaller tributaries. The Gulf Intracoastal Waterway, which stretches along the Gulf Coast from Brownsville, Texas to Apalachicola, Florida, is also considered part of the inland waterway system.

Jan 1, 1981

By James A. Bloom

To operate the Morris Fork Preparation Plant with a closed water circuit has been an elusive goal for Union Carbide. The benefits of a closed circuit have never been questioned. The removal of fine solids from washery water makes possible the recirculation and reuse of the water. Heavy media drag tanks and other separating machines perform better and more consistently with washery essentially free of fine solids. Finally, the production of a clarified effluent makes unnecessary the sludge ponds usually associated with a coal preparation plant. Why then do I say elusive? Because, since plant design was completed in 1970 we have been in hot pursuit of an ever-growing fine solids problem. In four years the minus 28 mesh material in the plant feed has nearly doubled. The replacement of conventional sections with continuous mining machines has led to a lowering in size and quality of product from the mine. In addition, increasing emphasis underground on roadway clean-up has contributed to the fines problem.

Jan 1, 1975

By Otto E. Zwanzig

You may think long before this talk has been completed that the speaker is belaboring the obvious. Please let me put to rest here and now any doubt which you may have in this regard by assuring you that is precisely my intent, and for a very specific reason. We all profess to know and recognize the obvious, but I am impressed increasingly how often we forget or fail to act upon the obvious. Shortly after starting my first job upon graduation from college, I was asked by my boss to participate in a course on practical communications, particularly as applied to conveying proposals effectively to the client -- be he customer or company president. The concept or philosophy underlying this program was so simple and obvious that in my youthful brashness I saw only a gross waste by the company of e good, solid $1930 in compelling me to take the course. The sequel to this experience occurred about five yews ago when I was directing a 300-man marketing group. At that time I enrolled a dozen of my department heads, and subsequently about a hundred other personnel, in the contemporary version of that sane program. Why? -- because they all knew the obvious, but I could see how imperfectly they were implementing it. Truly, a wide chasm exists all too often in our beliefs on the one hand and our practices on the other.

Jan 1, 1962

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

By D. Jacobson

There are many different machine setup parameters and variables that affect the production of cone crushers in a mineral processing plant. One of these variables is the eccentric speed at which the cone gyrates. In June 2012, pilot tests were conducted on a 200 hp high speed cone crusher to determine the production and operating conditions over a wide spectrum of eccentric speed. Every plant will have variations in the ore characteristics and feed rates throughout the life of the mine, and at times throughout a single shift of operation, which result in non-optimal use of the crushing energy and inconsistent process control. For high speed cone crushers, the crusher will exhibit a different capacity, power required, and discharge size distribution as the speed ranges over the design limits of the machine. This study documents the measured variation in production and energy efficiency both when the crusher was ran at full capacity as well as when the feed to the crusher was not sufficient to run at full capacity. Overall, the results match theory and the capacity and power fluctuated by 25% and 17%, respectively, over the speed range when operated full while there was an overall trend of slightly coarser discharge size distribution as the speed decreased. The results with the fixed feed rate were more telling, as the crushers had 4-14% higher production when making a theoretical minus 12.5 mm product when operating at the optimal speed as compared to the worst speed in the ?typical? speed range for this application. Secondary analysis of the fixed tonnage testing also showed that the power draw was more consistent with lower magnitude spikes at the higher speeds (higher cavity level), as on average the standard deviation of the power draw increased from 7% to 18% and the peak power spikes from 20% to 48% over the speed range tested. The findings lay groundwork for more efficient plant design. Varying the speed of the crusher can be used to tune the crusher speed during commissioning, adapt to changing ore conditions over long periods of time, or be used as a dynamic input into an advanced control system. Each action above would serve to make the crusher(s) more productive and more energy efficient, and would also have mechanical benefits for the machine. Key Words: cone crusher, ore reduction, process control, crushing efficiency

Feb 27, 2013

Newmont has been producing gold from the Carlin Trend for over 45 years. Naturally the focus, scale and complexity of the operations have changed considerably over this time. Newmont discovered and developed the Carlin Main ore body which is located about 32 km (20 miles) north of Carlin Nevada. The property was developed as a one mine one gold mill treatment plant operation which produced about 6,200 kg (200,000 Troy ounces) of dorè gold bars per year. The initial mine, mill and gold refining facilities were relatively small in comparison to today?s standards. The milling circuit used the Merrill-Crowe zinc precipitation process to recover dissolved gold and prepare a concentrated precious metal ?precipitate? to be melted into a dorè bar for sale.

Jan 1, 2012

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By Reul A. Dejú

The mineral olivine has been the subject of continued research by various authors. Paik (1967) conducted infrared and flotation studies of the adsorption of sodium alkyl benzene sulfonates on olivine. These studies are of interest from two points of view. First, in the metallurgical field it is of interest to understand the mechanism of silicate flotation using sulfonate collectors and second to a hydrologist studying the pollution of surface or subsurface waters it is of interest to study the reactions taking place when water plus sulfonates encounter a porous (silicate) medium. On the basis of Paik's study he was able to postulate a possible mechanism for the attachment of RSO3 (sulfonate radical) to the olivine surface. Parks (1969) has been studying the important influence of the structure of a silicate such as olivine on its dissolution mechanism and its related surface charge. Also Luce, a student of Parks (1964, 1965) has been studying the kinetics of dissolution of olivine using the techniques of direct solution analysis and infrared analysis. Certainly a classic in the study of silicate dissolution is the work of Murata (1940) on the reaction of orthosilicates (olivine in particular) with strong acid solutions. Many authors (Dejú and Bhappu, 1966. 1967. 1968, Dejú, 1969; Rhoades and Krueger. 1968, and Faust and blunter, 1967) have reported studies of the behavior of silicates immersed in water (especially orthosilicates) and have found that there is an exchange of cations from the silicate surface for H+ from the water. Studies by Dejú and Bhappu have also included the system olivine-water-amine.

Jan 1, 1971

By Gordon O. Prickett

In two case studies we look at strategies of acceptance that the analyst can employ to gain entrance and to see his problem solution out to use. The first example comes from metal mines. The problem area was excessive usage and cost of wear parts in the concentrator and an atmosphere of crisis over frequent and unexpected breakdowns. The second case pertains to coal exploration. Better methods were being sought for representing coal quality in developing reserve tonnages. The first strategy is - Develop a detailed Human Impact Statement. The second strategy is - Write down in plain language with the keeper of the problem what he will consider as success in dealing with his problem.

Jan 1, 1978

By V. Bush, T. G. Killingsworth, E. P. Ruffel

Effective and sustained corporate energy management programs are becoming a necessity for energy users as electricity deregulation laws are enacted on a state-by-state basis across the country and environmental regulations pertaining to emissions become more prevalent. The “Total Energy Asset Management” (TEAM) approach has been developed to assist energy end users with the development and implementation of corporate energy management programs designed to reduce energy risks and increase energy cost savings. This paper highlights the ways in which this approach can be applied to the mining industry while minimizing initial program implementation costs and increasing potential program benefits. Nearly the entire mining industry has become very focused on identifying opportunities to reduce costs per unit of yield. The industry as a whole has increasingly faced pricing pressures in large part due to the effects of global competition. The result of international marketplace participation and the emergence of higher efficiency recovery techniques have resulted in flat or even decreased prices for mining products. Thus, opportunities to reduce costs are actually opportunities to gain a competitive edge over similar mining operations. Due to the energy-intensive nature of many mining operations, the costs associated with energy are often a substantial percentage of operating costs. Therefore, it becomes very important to develop the corporate mentality that energy is an asset whose use should be optimized globally. In addition to the cost benefits of the TEAM approach, other benefits may occur such as reductions in facility greenhouse gas emissions.

Jan 1, 2002

By Osvaldo A. Bascur, J. Pat Kennedy

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. The lack of an integrated approach makes the profitability of metallurgical plants lag behind that of other industries despite technical advances that have occurred in recent years. This results in significant deterioration in the ability to maintain a "smart” operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. Combining real-time infrastructure with portal technology is becoming an accepted methodology. This paper introduces real-time portals and team sites to support decision making by work- groups which require both real-time and documentary information from manufacturing assets, vendors, head office and the Internet. Workers get insight from the overall process effectiveness index based on key variables such as losses due to plant availability, performance efficiency and rate of quality. Real-time portals and smart clients are part of any real-time performance management (RtPM) solution. Three case studies in large metallurgical complexes are presented. PLANTS ARE YOUR STRATEGIC HANDICAP Information technology is arguably one of the fastest moving technologies used by the mining/metallurgical industry. However, the business model for managing that

Jan 1, 2004

By D. A. Shock

Utilizing the technology developed for oil well stimulation by hydrofracing, a disposal system which permanently fixes the waste has been proven. Large quantities of radioactive waste can be processed by a single well system making this method an attractive method for permanent radioactive waste disposal. The system depends on locating a relatively thick formation of impermeable, but easily fracturable rock such as a shale, creating a horizontal fracture, pumping the waste into the fracture in a form which will subsequently solidify and seal the fracture from the well system. The paper presents the theoretical considerations from creating and extending horizontal fractures and how these considerations were used in designing a waste disposal system which is now operating.

Jan 1, 1964