Search Documents

By Thomas P. Oxford

The impact of recent legislation on Florida phosphate industry operations has been dramatic. The most significant influences are described: the National Environmental Policy Act of 1969; the Federal Water Pollution Control Act Amendments of 1972; and implementation of the Florida Environmental Land and Water Management Act of 1972. Further discussion includes: critical examination of the recently completed EPA Areawide EIS; potential effects of the Resource Conservation and Recovery Act of 1976; the Surface Mining Control and Reclamation Act of 1977; current local and state laws; and summary of studies on radiochemical effects of mining, seepage from gypsum ponds, and dewatering of waste clays.

Jan 1, 1979

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The STG integrated method of grouting can be divided into the several phases as outlined in preceding chapters. For convenience in describing technical procedures, they can be grouped as: 1. Investigations in non-geotechnical, exploration bore¬holes. 2. Drilling the holes necessary for geotechnical investiga¬tions and for grouting. 3. Conducting appropriate hydrogeologic tests in those holes and consequent calculations. 4. The preparation of a clay mortar. 5. The preparation of a clay-cement grout with additives. 6. The injection of the grout. 7. Checking the quality of the grout curtain. Items 2, 4, 5 and 6 are discussed below. These activities contain the procedural aspects of grouting. 7.1 DRILLING GROUT HOLES Grout holes belong to a very select class of drillholes. The necessary drilling equipment must enable the operator to drill the holes in inclined, twisting directions. In addi¬tion, the equipment must permit drilling under structurally and hydrogeologically complex conditions. The equipment must permit the operator to conduct specific testing activi¬ties in the drillholes. These activities include hydrodynamic analyses, flowmetric analysis, and the installation and re¬moval of deflectors, packers, grouting plugs, casings, lin¬ers, pumping facilities and other work. As explained in Chapters 5 and 6, the grouting of sat¬urated rock is conducted both through holes drilled from the surface and through holes drilled from the face of a shaft, drift, or tunnel. The drilling of grout holes from the surface can be carried out by an aggregate of equipment that can be the same equipment used for drilling exploration boreholes. Depending on the projected depth of the holes, the STG ZIF- 1200MR and ZIF-650 drilling rigs (or modifications of them) are used. The SKB-4, SKB-5 and SKB-7 high-output drilling rigs (workover rigs) have been used in recent years. The STG BMP-24 drilling rigs are used for carrying out the descent-lifting operations for drilling holes from the sur¬face. In a number of cases, the UKB-500C, URB-3AM and URB-2A power-fed drilling equipment is used for drilling holes from the surface. It should be noted that the drilling of grout holes usually requires an electric drive assembly. Drilling with diesel drive assemblies would be used only to preclude the possi¬bility of losing electric power during drilling operations. Turbine drilling would be used only for appropriate techni¬cal-economic reasons. The selection of the grout hole design is determined by the hydrogeological and structural geological conditions at the site as interpreted in Chapters 2 and 3. The design of grout holes must be as simple as possible in order to min¬imize costs. Hole design guidelines can be adopted as a basis for this purpose, unless site-specific conditions require otherwise. The mouth of the drillhole must be outfitted with a guide-pipe having a length of at least 2 m and an outside diameter from 219 to 234 mm. The upper part of the hole must be attached by a jig consisting of borehole casing that has a diameter ranging from 108 to 146 mm. The length of the jig h is determined by the equation [ ] where k = 1.1 to 1.2 is the load factor; P,, is the injection pressure of the grout into the mouth of the drillhole; D is the external diameter of the jig pipe; m = 0.6 to 0.7 is the work condition factor; T[ ].1 MPa is the bonding value of the rock cemented to the jig. The grout hole is drilled from the jig shoe to the de¬signed depth using a rock-crushing bit with a diameter of 93 mm or more. However in complex hydrogeological condi¬tions when the shaft intersects unstable rock, other hole designs can be used. The diameter of grout holes must permit an aggregate of investigations to be conducted in them using down-hole borehole geophysical and flowmetric logging instruments. It is necessary to cement the casing strings reliably in the grout holes, thereby permitting the injection of the grout under high pressure through the pres¬sure tight mouth of the borehole. Technological details for drilling grout holes such as the rotational rate of the drill bit, the axial load on the rock¬crushing bit, and the drilling fluid flow rate are optimized for the specific rock-hydrogeological conditions largely by experience. The hole diameter and type of rock crushing bit are important variables in these details of drilling. It is advisable to drill holes using water as the drilling fluid. However in those cases where the hole walls are unstable or under very high ground water pressure, the use of a well¬ engineered drilling mud should not be precluded. Unfortu¬nately, drilling mud can influence test results. When steeply dipping fractures with inclination angles of more than 60 to 70° are encountered, it is necessary to drill guided, inclined grout holes. This procedure permits the maximum number of fractures in each hole to be stu-

Jan 1, 1993

By Johann Steynberg

The design and construction of a Concentrator based on initial pilot plant work is rarely perfect. Palabora's plant was no exception although the basic objective to produce copper in a safely conservative manner was certainly achieved in a profitable manner. identification of the metallurgical and mechanical deficiencies of the plant through operating experience and a better concept of the minerology of the orebody enabled the development of a more efficient process both in terms of the metallurgical performance and cost effectiveness. To maintain and improve this level of efficiency, continuous inspection and revision of the plant metallurgy and engineering standards is required. In this presentation a few of the investigations and changes are described: 1.0 Alternative methods to restrict and eliminate the detrimental effect of critical size material on the performance of an autogenous mill. 2.0 An analysis of the environmental condi¬tions in Palabora's grinding circuit and the introduction of high chrome balls as grinding media. 3.0 The role of magnetite in the beneficiation process at Palabora. 1.0 Alternative methods to restrict and eliminate the detrimental effect of critical size material on the performance of an autogenous mill.

Jan 1, 1985

By T. H. Parker

The Guasare Coal Project is located a short distance from Lake Maracaibo, in the Northwestern region of Venezuela. In 1987, Carbones del Guasare, a joint venture comprised of Carbozulia, ACC Venezuela, a subsidiary of ARCO, and AGIPCoal of ENI Group, Italy, was formed to develop the Guasare coal reserves for world markets. Drilling with the Venezuelan state of Zulia has indicated a coal resource of over 6 billion metric tons. Further exploration has delineated the Guasare deposit as an area particularly suited for cost-effective surface mining. The calculated mineable reserves of this area (300 million metric tons) and the coal quality characteristics are based on extensive core drilling programs.

Jan 1, 1989

By Barnettm Ray R.

As a result of the Farmington explosion, the U. S. Bureau of Mines commissioned the National Academy of Engineering to a determine what steps could be taken in a short time frame to significantly reduce fatalities as a result of underground fire and explosion in coal mines. Three areas were named by the Academy as having the greatest potential; survival, communications, and rescue. The Bureau subsequently awarded a $3-5 million contract to the Special Systems Division of Westinghouse Electric Corporation for the development of prototype equipment and procedures. These were recently tested in a simulated emergency situation and will be delivered soon. Contractor recommendations for utilization and for further development effort will be studied and appropriate action taken.

Jan 1, 1971

By Schebek, J. Warsen

"Data and information from sustainable development (SD) reports can be seen as a promising and easily accessible source for an Life Cycle Assessment (LCA), i.e. for generic Life Cycle Inventory (LCI) data in particular. The reliability and comparability of LCA results crucially depends on the quality of LCI data, that is defined by specific normative requirements. In parallel the GRI (Global Reporting Initiative) provides a set of guidance documents for enhancing the quality, rigor, and utility of SD reporting with specific reporting principles that address similar issues on a company level comparable to LCI data quality requirements on the process level. In order to assess the general suitability of the fundamental reporting principles for LCI data quality purposes selected reports from mining and minerals (M&M) sector are assessed within a detailed analysis."

Jan 1, 2005

By Juan L. Sepulveda

An MPSI KW-20 Tower mill has been tested at the Butte Molybdenum plant of Anaconda Minerals Company, as a substitute for the conventional 1.5x3.0 m (5x10 ft) tumbling ball mill currently used for regrind purposes. The Tower mill was operated in both open and closed continuous circuits. These results were complemented with a series of batch grinding tests to determine some of the operational features of this mill. The relative grinding efficiency of the Tower mill with respect to the tumbling ball mill was determined and the applicability of this new mill to a plant/heavy duty environment was assessed. Experimental results obtained on the regrind of moly concentrates indicate that approximately 40% energy savings can be realized by using the Tower mill instead of the ball mill.

Jan 1, 1984

By B. Listerud, G. Zhan, M. A. Jones

Barrick Goldstrike Mines Inc. (BGMI) operates the Betze-Post openpit and the Meikle and Rodeo underground mines. Because the majority of the orebody is located below the water table, mining at BGMI requires a significant dewatering program. BGMI has a comprehensive dewatering and water management system that experienced a peak dewatering rate of 4,400 L/s in the mid 1990s. Changes to the hydrologic/hydrogeologic system caused by the mine dewatering have been monitored by an extensive network of groundwater monitoring wells and surface water monitoring stations, which cover about 1,550 km2. In addition to the monitoring program, a new tool, called Interferometric Synthetic Aperture Radar (InSAR), has also been used to enhance the evaluation of changes. Finally, a groundwater flow model has been developed that successfully simulates and predicts aquifer responses in the mine area and region. The well-calibrated flow model has served as a reliable tool to develop dewatering and mining plans, and project post-closure hydrologic conditions in the region. This paper introduces the BGMI dewatering and water management system and the means used by BGMI to evaluate and anticipate hydrologic responses in the region. The water management and analysis system has been and continues to be an integral part of managing ongoing operations, planning and pricing out future activities and evaluating the long-term effects of mine water handling.

Jan 1, 2011

By James K. Hallenburg

Geophysical borehole logging is a valuable and inexpensive tool for coal deposit evaluation, development, and production. In addition to the usual determinations of depth and seam thickness, geophysical borehole logs can effectively and accurately determine the coal ash, moisture, and heat contents in situ. Location and evaluation of the partings can be done quickly and accurately. Overburden character determination, such as roof competence, dewatering parameters, ripability, trace element content of the coal and overburden, and sulfur content can be done with existing tools and techniques. The quality of such determinations depends upon the quality of planning and calibration.

Jan 1, 1984

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are sometimes large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy/Bureau of Mines- sponsored subsidence study currently underway at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County), West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar retreat mining. The initial findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water bevels at shallower depths.

Jan 1, 1985

By Anibal Gajardo

Clays for building bricks and roofing tiles in Chile are classified as common clays and ball clays, with deposits of sedimentary and residual origin, both Cenozoic in age. Deposits are known from north to south, through 11 of the 13 Chilean Administrative Regions, 18° to 39° South latitude, and from west to east, through three of Chile's main geomorphic features, namely the Coastal Plains, Coastal Range, and Intermediate Depression. Alluvial and lacustrine sedimentary common clay deposits are located in the northern and southern Intermediate Depression. The average chemical composition of clay deposits in I and I1 Regions, is 58 percent Si02, 16 percent A1203, and 4 percent Fe203 by weight; the primary minerals are sericite, quartz, feldspar, and albite. The average chemical composition of clays in Metropolitan, VI, and VIII Regions, is 52 percent Si02, 16 percent A1203, and 6 percent Fe203 by weight; the primary minerals are montmorillonite, quartz, and plagioclase. Residual common clay deposits occur in the Intermediate Depression and in the Coastal Range internal basins, VII, VLII, and IX Regions, and they represent surficial alteration of pumice beds and crystalline rocks. The average chemical composition of clay deposits derived from crystalline rocks is 58 percent SO2, 17 percent A1203, and 9 percent Fe203 by weight; the primary minerals are sericite, quartz, and clinochlore. Clay deposits formed from pumice beds contain 47 percent Si02, 24 percent A1203, and 10 percent Fe203 by weight; the primary minerals are kaolinite, feldspar, and cristobalite. Sedimentary ball clay deposits are located in the Coastal Plains and Coastal Range, VI, VII, VIII, and IX Regions, between 34" and 39" South latitude. The average chemical composition of the ball clay deposits is 51 percent ,902, 28 percent A1203, 5 percent Fe203 by weight; the primary minerals are kaolinite, quartz, and sericite (illite?). These clay deposits supply the Chilean building sector with over one million metric tons (mt) (1.1 million short tons [st]) of material per year. The average growth rate of clay consumption during the period 1993 through 1997 was 10 percent annually. The clays are used by both mechanized plants and handcraft facilities.

Jan 1, 2001

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By Earl R. White

In 1950 Kaiser Steel Corporation acquired control of the Utah Fuel Company, a pioneer Utah coal concern owning large reserves of high volatile coking coal near Sunnyside, Utah. The mines at Sunnyside have been producing high quality coking coal since the late 1890's. Kaiser Steel acquired the coal deposits at Sunnyside in order to supply the necessary coke for its steel plant at Fontana, California. The Sunnyside coal deposits are made up of two mineable beds, the upper and lower Sunnyside seams. Both seams outcrop along the southward facing escarpment of the Book Cliffs. The coal seams dip under the massive sandstones of the Book Cliffs to the northeast at 5 to 22 pct., with the steepest-part being near the outcrop. Mining at Sunnyside up to 1961 had been carried on with room and pillar methods. The deep cover and rotten roof conditions, along with the need of increased tonnage, required a change of mining technique. Numerous ideas were presented, discussed, and economically analyzed. Several people involved in these discussions, with the aid of W.W. II, had been introduced to the European methods of coal mining, namely the longwall technique. The European mines had long been plagued with near similar conditions as those at Sunnyside, particularly the deep cover problem. The longwall method seemed to be working very well under these conditions, and with the extensive studies given longwalling by the Kaiser Steel mining officials, it was decided to give longwalling a try.

Jan 1, 1976

By P. E. Damon

An arsenal of isotopic techniques is avail-able that can date the full range of hydrothermal ore deposits. The following are prerequisites for ideal results: (1) Careful collection of samples that are related to the event in a field and process context; (2) Optical examination of the component selected for dating to be sure that it has not been altered; (3) Careful preparation of a pure component of the sample selected for dating; (4) Precise and accurate measurement; (5) Knowledgeable interpretation of the data with reference to decay systematics, properties of the component analyzed as well as the field context and thermochemical environment of the ore process.

Jan 1, 1992

By Phillip R. Moyle

Voluminous deposits of commercial-grade phosphate occur in sedimentary strata in a 350,000 km2 (135,000 mi2) area of the middle Rocky Mountains of North America known as the Western Phosphate Field. The Permian marine strata that host the phosphate were deposited on the western margin of the North American craton and subsequently deformed, first by folding and thrust faulting of the Laramide orogeny, and then by Cenozoic Basin and Range block faulting. Carbonate fluorapatite is the primary phosphorus-bearing mineral. Organic matter is abundant in some strata, and both biogenic and non-biogenic pyrite are also present. Certain strata are enriched in several trace elements, especially in arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), molybdenum (Mo), selenium (Se), vanadium (V), uranium (U), and zinc (Zn). Phosphate has been mined from the Western Phosphate Field for nearly 100 years. Phosphate mining and processing constitutes the largest mineral industry of Idaho, producing more than $600 million in processed mineral value in 1997. Resource management agencies, phosphate producers, and others are concerned about the release of Se from phosphate mine wastes, especially at Maybe Canyon, and the potential effects that Se and other trace elements may have on the environment and on human health. U.S. Geological Survey (USGS) Mineral Resources Team scientists initiated a multidisciplinary study of the Permian Phosphoria Formation and related rocks in the south- eastern Idaho sector of the Western Phosphate Field in response to a request by the U.S. Bureau of Land Management (BLM). Studies to date reveal that Se is present in several phases, including native Se, and in an as yet unidentified form, possibly an organo-Se compound. Selenium is also present in pyrite and sphalerite. Selenium concentrations range from 1.2 to greater than 1,000 parts per million (ppm) in samples collected from exposures of the Meade Peak Phosphatic Shale Member of the Phosphoria Formation (Meade Peake) at Enoch Valley. The results suggest that Se concentrations vary spatially across strata and with depth, perhaps comparable to spatial variations of phosphate and organic carbon concentrations throughout the Western Phosphate Field demonstrated in previous studies. Some Se-enriched strata may be of adequate dimension to allow selective extraction during mining. Such units could be handled separately from the main ore process or waste streams and isolated in order to reduce the potential for release of Se to the environment

Jan 1, 2001

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

By O. E. Wheeler

The use of the walking dragline as a stripping tool has increased dramatically in the past two decades. The reasons for its increased popularity and some historical background on its introduction into the mines are given in a recent paper by Learmont. (l)* The history need not be recounted here except to show the trend to longer booms which has accompanied the growth in machine size. Figure 1 shows the change in maximum operating radius on Bucyrus-Erie machines which has occurred over the years and Figure 2 shows the corresponding change in maximum boom lengths. Reference 1 also presents some of the reasons for expecting this trend to longer booms to continue. There are many design parameters affected by the increase in boom lengths; swing power, hoist and drag rope lengths, and drum capacity, to list just a few. The purpose of this paper is to discuss only the structural implications of using longer booms. As in the design of any structure, the various facets of boom design are interrelated and a process of optimization between them must be worked out either by evolution or by conscious iterative effort. The decisions we have reached about such things as material selection, structural arrangement, and applicable criteria, have not come into being overnight but represent instead many years of design experience and a fair amount of recent concentrated analytical effort. In the following pages an attempt will be made to first, state those decisions, second, explain how we arrived at that particular result; and third, describe what we expect future developments to be which might influence us to change those decisions.

Jan 1, 1976

By Allan G. Provost

Shaft construction is assuming ever increasing importance when new mining enterprises are considered. The reasons for this increased emphasis is the much greater depths at which many new ore-bodies are being developed and the rapid depletion of near surface reserves requiring mines to go to greater depths on existing deposits. These greater depths increase the probability of exposure to unfavorable geologic conditions and it is more likely that high ground and/or water pressures will be experienced at these depths. The large capital costs involved and the critical position of a shaft in the overall mining program necessitate that this element of project development be given careful and critical consideration. The Henderson No. 2 Shaft is located in the Rocky Mountains of north central Colorado (See Figure I), about 55 miles west of Denver, near the community of Empire in Clear Creek County. At the 10, 442 foot collar elevation, winter arrives in late September and brings snow to contend with until May. The labor force for Shaft No. 2 is approximately 90 men. They are provided access to the project via all-weather U. S. Highway 40. SHAFT DESIGN The Henderson No. 2 Shaft is a 28-foot I. D. circular, concrete lined (1 foot thick) vertical shaft. The final depth will be approximately 3100 feet

Jan 1, 1972

By Kevork Chouzadjian, Gary Davis, Nicholas Katsikaros, Bruce Kelley, Mellie Mavatoi

A process has been developed to recover gold and copper from two waste materials at the Bougainville Copper Limited mine in Papua New Guinea. It involves the bioleaching, in reactors, of a pyrite concentrate to liberate refractory gold and generate sulphuric acid, ferric sulphate and biomass for bacterial leaching of a chalcopyritic waste rock dump. Gold is to be recovered by cyanide leaching and copper by solvent extraction/electrowinning. The reactor bioleaching was developed in continuously operated reactors of 1 m3 capacity by CRA Advanced Technical Development at Cockle Creek, while the dump leaching was developed in 750 kg columns on site at Bougainville Copper Limited. The process was to be piloted on site.

Jan 1, 1990

By C. E. "Sam" Lovewell

In approaching a discussion of production of cement, I hope I won't be like the porter in the bank who was asked if he could give some details on the rediscount rate. He replied, "Boss, when I said hello, I told you all I know." Need for change every so often is illustrated by the story of the little boy four years old who had not spoken a word in those four years. One morning he said, "This damned oat meal is burned'." His Dad was amazed and said, "Son, how come you haven't said a word for four years and now out of a clear, blue sky you say, "The oat meal is burned." Johnny said, "Well, up to now everything has been all right." Not being a mining engineer myself, and my subject not dealing with mining engineering directly, I can only hope that you will agree that the subject has current relevancy by the feet that it can materially improve our environment by putting to good use a potential environmental polluter; namely, fly ash. The profitable utilization of fly ash can reduce cost of use of coal as an energy source. Therefore, it behooves us all to explore to the greatest depth, the pluses and minuses occasioned by its use wherever possible. My particular subject and my particular interest lie in its utilization as a blend in the production of Type IP Portland-Pozzolan Cement meeting requirements of ASTM C-595, Type IP.

Jan 1, 1974