Search Documents

By Lewis L. Oriard

The authors outline the development and application of blasting methods put into use 11 years ago at the Berkeley Open-Pit Mine, Butte, Montana. The blast design uses a very short delay (5 milliseconds) between detonation of explosives charges, a feature challenged several times in principle despite its success for Anaconda. Concern is expressed over the categorical rejection of very short delay blasting which can make the difference between success and failure of major mining operations. There is ample evidence to show that the method can be used successfully and not violate the concerns of the public.

Jan 1, 1980

By Russell J. Sheets

Reactivation of highwall slope failures during adverse weather had intermittently impacted haul road access into a previously mined open pit. These impacts ranged from limited access to full closures; however, the greater impact was to an underground mine that was developed within the open pit. Following several significant precipitation events, a rapid snow melts greatly accelerated movements finally closing the haul road and destabilizing other past failures. In addition to re-designing the overall pit access, the decision was made to relocate the primary portal to a more stable highwall. An accelerated surface geotechnical review was required to advance the portal relocation; however, only existing information from past investigation, existing geology model, visual inspections, and slope monitoring data were available for the assessment - no new investigations or data collection could be completed within the allowable timeframe. The evaluation included a review of the geology, an assessment of the current highwall condition and previously observed performance, and a rockfall analysis to evaluate existing catchment above the proposed new portal location.

Feb 1, 2024

By Dave Southworth

After Abe Lee discovered gold (in April 1860) near the site of present-day Leadville, Colorado, he and is group staked nearly all of California Gulch with "speculative claims." They did so in an effort to grab any property that might be potentially profitable. But the plan did not work. New prospectors demanded a miners' meeting, from which arose the official "Bylaws of California Mining District, California Gulch, Arkansas River." These bylaws, adopted on May 12, 1860, established provisions as to the number, size and type of claims that could be filed. Fair laws invited more newcomers. By mid-summer, 5,000 people with tents and wagons were scattered from one end of the gulch to the other.Among the earliest arrivals to the region that spring were Horace Austin Warner Tabor and his wife, Augusta. H.A.W. Tabor, who was to become a pillar in the development of Leadville, arrived at California Gulch during a food shortage. He sacrificed his oxen so that hungry miners could eat. By doing so, he immediately became the friend of many. Augusta established a little store where she sold her baked goods and provided meals. Like most of the men, Horace prospected the surrounding hills. He only did so, however, for a short time. California Gulch yielded more than $5 million in gold during the next five years. By 1866, however, the placer gold was gone and most of the miners had packed up and left. Charles J. Mullen and Cooper Smith, who were grubstaked by a Philadelphian named J. Marshall Paul, found a new, rich lode at the Printer Boy Mine in 1868. It was the first underground gold mine in the Leadville area and marked the transition from surface mining to underground hard rock mining. Its discovery created a new but modest flurry of activity. Heavy black sand covered the region and made gold mining difficult. In 1875 William Stevens and Alvinus Wood decided to have the sand assayed. They discovered that it contained 15 ounces per ton of silver and was rich in carbonate. Stevens and Wood kept their find a secret for nearly two years. When the word spread in late 1877, the silver boom was on. In 1878 prospectors, merchants and others trickled into town from all directions. Dr. David H. Dougan closed his office. in Alma, crossed Mosquito Pass and set up shop in Leadville. Nobody seemed to need a doctor, however, and Dougan sat in his office for 28 days without a customer. On the 29th day he received word that there had been a mining accident and he was needed immediately. -That was the begin¬ning of his illustrious career in Leadville. Dougan was a successful physician, became mayor in 1881 and was later president of the Carbonate National Bank. Leadville was a simple community of log structures in 1878. By June of the following year, however, it had blossomed considerably. According to Cass Carpenter, as of May 1,1879, Leadville had "...19 hotels, 41 lodging houses, 82 drinking saloons, 38 restaurants, 13 wholesale liquor houses, 10 lumber yards, 7 smelting and reduction works, 2 sampling works for testing ores, 12 blacksmith shops, 6 livery stables, 6 jewelry stores, 3 undertakers and 21 gambling houses where all sorts of games are played as openly as the Sunday School sermon is conducted." Additionally, there were 36 brothels. When George E. King and other architects arrived, Leadville took on an air of elegance and sophistication. In sharp contrast to some of the Victorian-style, gingerbread-laced homes in Leadville, its suburbs were comprised of many tenement shacks and plain cabins mixed with a few commercial buildings, many mines and smelters. Mines sprinkled the area east of Leadville like pepper from a pepper shaker. Wherever there was a cluster of mines, a camp usually sprang up. Most were very close together. South of Leadville the giant Arkansas Valley lead smelter sprawled out between Stringtown and Bucktown in an area known as Smelter Valley. Founded in 1879 as the Billing and Eilers Smelter, the Arkansas Valley plant was operated by the American Smelting and Refining Company. Several other smelters operated in the vicin¬ity. In April 1878, Horace Tabor grubstaked prospectors August Rische and George Hook. For $64 worth of supplies and tools, he was guaranteed a one-third interest in their findings. Rische and Hook discovered the Little Pittsburg (often spelled Pittsburgh) Mine and made Tabor an instant millionaire. Tabor once purchased a "salted" mine, the Chrysolite; but instead of considering it a bad deal, he further developed the property and struck rich silver ore. Later, Tabor purchased the Matchless Mine for $117,000, possibly the only investment he made without partners. During its peak years, the Matchless yielded $1 million worth

Jan 1, 1998

By C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 RC was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique and weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure errosion it was found that there was a synergistic effect between corrosion and erosive wear. Erosive wear rates are given as a function of pH and mineral type.

Jan 1, 1984

By J. Y. Lee, J. Kang

"A selective chlorination process using cuprous chloride (CuCl) was investigated for producing high-grade chalcocite (Cu2S) from chalcopyrite (CuFeS2) feed. The chalcopyrite feed was reacted with CuCl in the presence or absence of sulfur (S) at temperatures between 900 and 1,100 K for five hours under an argon gas atmosphere. The experimental results indicate that iron (Fe) was selectively removed from the chalcopyrite feed as ferrous chloride (FeCl2) at 1,100K and the mass percentage of Fe thus decreased from 31.5 percent in the feed to less than 0.05 percent in the residue, under certain conditions. As a result, high-grade Cu2S was obtained from chalcopyrite in a single step. This new selective chlorination of chalcopyrite using CuCl as a chlorinating agent is therefore feasible for producing high-grade Cu2S.IntroductionCurrently, blister copper (Cu) is commercially produced from sulfide ores by pyrometallurgical methods. These methods entail matte smelting and converting, with the removal of iron (Fe) and sulfur (S) as slag — mainly Fe2SiO4 — and sulfur dioxide (SO2) gas, respectively.In the pyrometallurgical method, as shown in Fig. 1 (Schlesinger et al., 2011), Fe is removed through two steps at high temperatures of around 1,500 K to reduce the loss of Cu during slag formation. However, the slag still contains 1 to 8 percent Cu. Therefore, Cu in the slag is recovered by slag treatment processes, after which the concentration of Cu in the slag decreases to around 0.4 to 1.3 percent. Although Cu is recovered, the slag that had undergone the treatment processes is difficult to use as a feedstock for ironmaking owing to the small amount of Cu remaining in the slag (Schlesinger et al., 2011).In addition, large amounts of SO2 gas are generated by the oxidation of S in the current Cu production process. The SO2 gas generated is captured and used to produce sulfuric acid (H2SO4). However, despite the development of SO2 gas-capture technologies, the emission of SO2 gas is still a problem in terms of environmental considerations.Several studies had been carried out in the past to overcome the drawbacks of the current process. The extraction of Cu from sulfide ores using a chlorination process is one alternative that had been investigated by several researchers. Most chlorination processes used chlorine gas (Cl2) as a chlorinating agent at temperatures between 573 and 1,023 K under an inert atmosphere (Donaldson and Kershner, 1962; Olsen et al., 1973; Kumar, Li and Warren, 1985, 1987; Kanari et al., 1999; Kanari, Gaballah and Allain, 2001)."

Jan 1, 2017

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By Felicia F. Peng

The naturally occurring aged manganese oxide coated on the granular media was found to have a catalytic effect on the removal of low concentration of Mn(II) (-1 ppm) from drinking water. Applying this principle, a manganese removal technique was developed for removal of higher concentration of Mn(II) (-100 ppm) from mine drainage by using various aged filter media and synthesized granular media with manganese oxide coatings. Laboratory-scale continuous granular media column experiments were conducted to assess the feasibility of manganese oxide-coated granular media for Mn(II) removal from synthesized mine drainage. The removals of Mn(II) were evaluated as a function of operation parameters including solution pH, manganese oxide concentration coated on the media, interstitial velocity, and oxidant concentration of influent. Higher solution pH and/or higher manganese oxide concentration promoted the removal of Mn(II) on the oxide-coated granular media under low interstitial velocity. Addition of sodium hypochlorite as an oxidant in the influent resulted in continuously regenerated oxidized surface to serve as the catalyst for Mn(II) oxidation reaction on the surface of oxide-coated media.

Jan 1, 1994

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By William A. Wallace

Common mineral resources (sand, gravel, crushed stone, etc.), which are so necessary for the construction of metropolitan areas, are rapidly being depleted or otherwise rendered unavailable in the very areas that need them most. However, the problem of planning for these resources involves a number of independent and dependent variables that must first be defined and related. Finally, a dollar value must be assigned where possible. Complex interrelationships between the variables and their dependence on outside factors has made mathematical "solution" of the problem of planning for non-renewable mineral resources difficult at the present time. Therefore, the use of computer simulation is suggested as a means by which this complex problem can be investigated. The purpose of this paper is to report on a continuing research program whose objectives are: (1) to delineate the factors involved in planning for the utilization of common mineral resources in urban-suburban environs; (2) to construct a planning model for these materials amenable to computer analysis, (3) evaluate the model by using test cases, and (4) perform a sensitivity analysis to determine the initial parameters in future planning for these materials.

Jan 1, 1968

By J. Y. Hwang

Coal cleaning with traditional magnetic separation usually yields unsatisfactory results because minerals associated with coal, such as quartz, clay, pyrite and calcite, are weak-or non-magnetic. Magnetic reagent technology is a new mineral processing technology with the capability to enhance the magnetic property of minerals selectively. This reagent can be adsorbed selectively on minerals through the control of surface chemistry and, thus, result in selective magnetic enhancement. The application of this technology on coal cleaning has been experimentally demonstrated. Good separation results can be obtained at low to medium magnetic field strength. Comparison with other processing technologies is included.

Jan 1, 1992

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By L. Alagha, L. Sanchez-Calderon, M. Silwamba, W. Kirk

Selenium-rich metallurgical waste, also known commercially as “crude selenium,” is a byproduct of the copper (Cu) refining process. This by-product, contains ~ 90% selenium (Se), precious metals, platinum group metals (PGMs), and other critical elements. This study investigated the leaching efficiency of Se from the sludge under alkaline conditions using different oxidizing agents to enrich PGMs and precious metals in the leach solid residue. The effectiveness of each oxidizing agent during leaching was assessed and compared. Additionally, Eh-pH diagram for Se was established under specific experimental conditions and utilized to inform process optimization. Key variables, including leaching time, temperature, and oxidant concentration, were evaluated for their impact on the efficiency and the selectivity of the oxidative alkaline leaching process.

Feb 1, 2025

By J. E. Sepulveda

Tar sand deposits in the. Stare of Utah contain more than 25 billion barrels of in-place bitumen, Although thirty times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion barrels), The term "tar sand" refers to a consolidated mixture of bitumen and sand, Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water extraction process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique., Experimental results indicated that, for a given tar sand sample, percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage, These variables were identified by means of an experimental, factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence gathered in this investigation seems to indicate that a hot-water extraction process for Utah tar sands would allow for the efficient utilization of this important energy resource.

Jan 1, 1978

By D. Lauriski, E. D. Thimons, A. C. Smith, D. C. Fredley

The National Institute for Occupational Safety and Health (NIOSH) and Northwest Barricade LLC (NWB) conducted a study to evaluate the effectiveness of a novel fire blocking gel for use in underground coal mines to extinguish or retard the growth of a coal fire. The gel agent was subjected to controlled laboratory testing to assess its ability to delay coal ignition. It was then evaluated to determine if manual fire hose application could be used to apply the agent to mine roofs and ribs to provide a safe egress for mine rescue teams from a fire area. The gel agent was also evaluated in a water sprinkler system to determine its potential for use in conveyor belt fire suppression systems. The agent was then tested in live-fire exercises to examine its effectiveness in retarding and extinguishing a deep-seated coal fire and wood fire. Lastly, the ability of a mine rescue team to quickly and safely apply the gel agent to a mine entry during a simulated mine fire exercise was determined.

Jan 1, 2011

By J. Allen Hennessy

INTRODUCTION The increasing price of gold and silver over the past 10 years has caused increasing activity in the exploration, evaluation and development of precious metals projects. Many of these deposits are relatively low grade and short lived which makes them economically sensitive to the major project variables such as metal price, capital cost, operating cost and of course, tonnage and grade. These deposits often have a high variability (a coefficient of variation -- o/u -- of 2 to 5) and an intermixing of ore and waste, making ac- curate ore reserve estimation difficult, especially when using traditional estimation techniques. Often, the estimation errors are not the 10-20% that we see in base metal deposits, but the errors in grade and tonnage can be as high as 50%, which can obviously have a very substantial impact on project Recent developments in geostatistics when coupled with a sound geologic under- standing of the deposit can significantly improve reserve estimates of these variable precious metals deposits. Examples will be given of actual deposits where the traditional estimates were significantly different from the mining reality. An attempt will be made to explain the applicable geostatistical tools with a minimum of geostatistical jargon and without complicated formulas. The key to improving the reserve estimates is a clear understanding of the deposit geology and especially the structural controls, the use of local estimation techniques that recognize the intermixing of ore and waste and the effect of selective mining on recoverable reserves, and the use of a global reserve estimation technique to check the results of local estimation. Geologic Controls The vast majority of gold and silver deposits being mined or developed in the western United States would be classified as epithermal deposits. These are formed by hydrothermal fluids (hot water) flowing upward through the rocks and depositing the precious metals as the fluids cool or reach areas of lower pressure or favorable chemical sites. These environments are similar to present day hot springs-type environments with some deposits being clearly associated with surface hot springs such as the Homestake McLaughlin deposit in northern California. These hydrothermal deposits can occur in sedimentary rocks resulting in deposits such as those of the Carlin district or the Jerritt Canyon deposit or the hydrothermal systems can occur in volcanic rocks forming deposits such as Round Mountain, Manhattan or Paradise Peak. The mechanisms of formation were similar in either case with the solution flow controlled by geologic structure and precious metals deposited when the conditions of temperataure, pressure and chemical environment were favorable. The gold and silver hearing solutions travel through permeable faults and fracture systems depositing the metals along these channels. The grades are often highest in the central parts of these conduits (veins) with lower grades in the surrounding rocks. An understanding of the nature, distribution and orientation of these plumbing systems is important to a realistic reserve estimate. The point to be emphasized here is that, good, sound geology in the form of geologic mapping, logging of rotary chip samples and a few carefully logged core holes can signifi- cantly improve an ore reserve estimate.

Jan 1, 1987

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels, as related to maintenance (service) intervals, during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type (technology) and tuning of the engine, the type of work performed as related to the engine workload, suggested maintenance intervals, the altitude, the temperature and the humidity of the atmosphere of the underground mine, the properties of the fuel, the operator's training and experience level. Necessary ventilation quantities were calculated based on exhaust gas concentration measurements, site specific relationships between pollutants and adjusted air quality indices. Diagrams comparing necessary and recommended air flow for several equipment groups featuring two engine types and for different maintenance intervals are presented.

Jan 1, 1998

By C. S. Thompson, P. A. Ciullo

Pyrophyllite is a naturally occurring hydrous aluminum silicate with the molecular formula SiO,,AI,,(OH), or, as more commonly expressed, the oxide formula A120,~4Si02~H20. Pyrophyllite is rarely found in deposits as the pure mineral and is often intimately associated with quartz, sericite, kaolinite, and diaspore. These associated minerals, to a large degree, help determine the most appropriate commercial application for a given pyrophyllite ore. Structural similarities plus the generally soft platy nature of pyrophyllite has in the past caused it to be included with talc in applications and production data. The Minerals Yearbook, published annually by the US Bureau of Mines (USBM), still reports on talc and pyrophyllite together, although admitting that they do not share the same uses. Pyrophyllite has also at times been considered a clay mineral because of its structure and chemistry. The refractory properties of pyrophyllite have been known for nearly 200 years, but it has only been in the past 60 to 70 years that a variety of applications have been developed to exploit the unique characteristics of this mineral. Worldwide, pyrophyllite is a component of refractories, whiteware, foundry mold dressings, pesticides, paint, plastics, rubber, cement, fiberglass, and soap. Historical Overview The most salient refractory features of pyrophyllite are its low coefficient of thermal expansion, high thermal conductivity, low moisture expansion, and good resistance to corrosion by molten metals and basic slags. One of the first recorded uses of this mineral was as firebrick in Japan in the early 1800s. This followed its discovery in 1797 on Mount Omotoyama at the site of the present Mitsuishi mine. In addition to firebrick, sawn blocks of ore were used for carvings and in the manufacture of slate pencils and signature seals. The Mitsuishi mine is still one of Japan's largest. By the mid-1800s, refractories were being made in Japan from roseki (a pyrophyllite-bearing ore) for the construction of metal melting furnaces. The mineral did not get its name until 1829 when R. Herman, testing a sample of supposed talc from the gold-quartz veins at the Berezovo deposit in the Urals, showed that it was actually an aluminum silicate and designated it pyrophyllite. This name was derived from the Greek pur for fue and phullon for leaf, in allusion to the effect of heat in causing separation of the laminae in foliated varieties (Mellor, 1927). The exact date of the discovery of pyrophyllite in the United States is uncertain, but it is believed that the talc and soapstone deposits noted in an 1827 report on the geology of the slate belt of North Carolina were actually pyrophyllite occurrences (Olmstead, 1827). Pyrophyllite was first used in North Carolina on a local basis in the early 1800s. Blocks were sawn and cut for use as stove linings, mantels, chimneys, fireplaces, and gravestones. This was the material of choice because it did not shrink when heated, but cut easily and hardened as it weathered. Pyrophyllite crayons were sold commercially by local gold miners for steel marking and as tailor's chalk from about 1800 until 1922. It was during this period that pyrophyllite was discovered near the town of Hemp (later renamed Robbins), NC. The large quantity of scrap resulting from the sawing of crayons at this deposit prompted the construction in 1921 of a grinding plant. The ore scrap was ground to fine granules and sold to asphalt producers to prevent shingles from sticking together. By the mid-1930s, milled pyrophyllite from North Carolina was also being successfully utilized by the ceramics industry in whiteware for its low cost and ability to shorten firing time. Also during the 1930s, pyrophyllite was first used in kilncar furniture in the United States. Canada was another early entrant in the pyrophyllite business. Mining at the Foxtrap deposit on the Avalon Peninsula of Newfoundland began in 1904, with ore shipped to the United States. Production from this deposit was mostly sporadic in the ensuing years until 1956 when mining began for shipment and captive use in US tile manufacture. This production has remained continuous and still essentially captive to the present. The Foxtrap deposit is currently the sole commercial source of pyrophyllite in Canada.

Jan 1, 1994

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By D. I. Hoyer

A preliminary model has been developed for autogenous pebble milling using information obtained from studies on ball milling and SAG milling. The model treats the breakage as the weighted sum of first-order breakage of smaller particles by tumbling pebbles, non-first order breakage of larger particles which are too large to be nipped properly by pebbles, autogenouS fracture and chipping of larger lumps to form pebbles, and autogenous fracture and abrasion of pebbles. The model includes the effects of residence time distribution, classification through the exit grate, and a mass transfer relation which describes the accumulation of fine material in the mill. Example simulations are given, based on breakage parameters determined from batch grinding tests in laboratory mills. fracture breakage and abrasion. In the development of these preliminary mass balance equations it will be assumed that breakage by fracture is first-order, but this assumption will be modified later in the paper. It will also be assumed that the residence time distribution of a long autogenous mill can be described by an equivalent series of m fully-mixed mills, with a classification action imposed on the mill contents by the discharge grate. Size distributions are expressed as a v2 geometric series, numbered 1 for the top size down to n for the fines, or "sink" interval. If the holdup in the mill is W then the rate of breakage of material in size interval i is given by SiwiW, where wi is the fraction of material in size interval i, and Si is -the overall specific breakage rate of size i material (fraction per unit time).

Jan 1, 1985

By Steve Axen

In situ mining is now considered an alternative mining method for some ore bodies. The in situ operation consists of a well field designed from reservoir properties and geological information; the wells for such a field are then drilled, cased, and cemented, using good designs and practices to eliminate future problems. Injection and production (recovery) systems are required to be corrosion resistant. Hand in hand with the mining operation is the metal extraction plant, the entire operation offering an environmentally acceptable method for metal recovery. Great opportunity exists in this field for mineral engineers; presently, they must borrow knowledge from other fields, since the schools have not yet addressed this specialty.

Jan 1, 1979