Search Documents

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production; however, the thermal state of pellets in drying section is still unclear. In this study, the temperature distribution of drying section was investigated using computational fluid dynamics (CFD). Based on the calculated results of airflow velocity, space temperature distribution, and the temperature change of pellets, it concluded that there is a coupling effect in drying section in traveling grate. The gas with higher temperature in DDD transfers heat to UDD through the gap of the insulation board, and the temperature gradient of the pellet bed changed before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD was displayed in UDD in advance. Moreover, a contrast experiment was conducted to verify the model.

Feb 1, 2021

By Terry A. Rightnour

Multiple seam mining is predominant throughout the central Pennsylvania Appalachian coal fields. Wide ranges in individual seam thickness, coal quality, and overburden characteristics are common throughout the region. On typical mining permits, ranging from 404 x 103 to 2023 x 103 m2 (100 to 500 acres), often as many as eight seams are concurrently mined, with each interburden requiring unique economic and environmental consideration in the mine plan. Specifically, this paper presents several planning tools and operational guidelines developed in response to current regulations for the special handling of potentially acid-forming materials as they are related to development and operation of multiple seam mines.

Jan 1, 1984

By W. G. Kegel

The past few years have produced a rash of demands for changes in America's way of doing things. From manufacturer to consumer, the rules have been changed. Some of the demands were needed and, when legislated to requirements, did manage some good for all concerned. Other demands made by zealots and taken up by regulatory agencies have forced costly changes on our way of life. No segment of industry has been exposed to more new rules and regulations than the deep coal mining industry in the United States. There is no denying that some good has evolved, but most mining men know that the effects have done more to reduce production and increase cost than they were ever intended to do.

Jan 1, 1975

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By C. Waddell

PDMI mines five different grades of ore. Shovel operators were experiencing problems differentiating one material type from another. In 1997 PDMI decided to try GPS ore control to aid operators in identifying material boundaries. Computer generated ore control maps and GPS data defining the shovels' position is fed to a computer on board the shovel. A monitor, located near the shovel operator, displays material types, their boundaries, and the shovels' position and movement in relation to the mining face. This information has reduced errors in material identification by 50%.

Jan 1, 1998

By W. W. Dudley

The U.S. Geological Survey, in support of underground testing of nuclear explosives, has developed a technique (Dudley, 1910) to predict the inflow of ground water to large underground chambers that are cylindrical in shape. By treating the chamber as a large-diameter well pumped at constant drawdown, the nonsteady discharge can be computed by the method of Hantush (1961) for analyzing flowing wells under leaky artesian conditions. In mining applications, whether for mineral recovery or for nuclear testing, the most serious departure from the conditions of Hantush's model results from the gradual enlargement of the opening under drained conditions. Inherent in the analytical technique is that the "well" is fully completed at the time that dewatering begins. Because safety is the prime concern, however, initial pumping systems or personnel evacuation procedures must be designed to handle the greatest conceivable inflow. DEFINITIONS Because somewhat different meanings are attached to similar words in different technical fields, the U.S. Geological Survey definitions (Lohman, 1970) of several hydrologic terms used in this report are given below. An aquifer is a formation, group of formations, or part of a formation that contains sufficient saturated permeable material to yield significant quantities of water to wells, and springs. A confining bed is a body of material lying stratigraphically adjacent to one or more aquifers and having a hydraulic conductivity distinctly lower than that of the aquifer. The total head (dimensions L) of a liquid at a given point is the sum of three components: (1) elevation head, he, which is equal to the elevation of the point above a datum; (2) pressure head, hp, which is the height of a column of static water that can be supported by the static pressure at the point; and (3) velocity head, hv, which is the height the kinetic energy of the liquid is

Jan 1, 1971

By J. W. Motter

Currently, virtually all new electric power generation systems under construction are designed with natural gas as the primary fuel. Factors driving these construction decisions involve sustained low prices for natural gas, environ-mental (and consequent regulatory) risks associated with the use of coal for power generation, and relatively high costs of construction for conventional coal-fired power plants. Despite the unarguable abundance of coal in the US. and worldwide, a fundamental question arises: What will be the role of coal in electric power generation in the 21st century? Congress, recognizing the vital and strategic importance of preserving the coal option for electric power generation, authorized the Clean Coal Technology Program. This pro-gram, with original funding in excess of $2,500 million, is intended to promote the demonstration and commercialization of a new generation of clean, efficient coal-based energy technologies through collaboration and partnering with private industry. The two technologies being demonstrated under this program which are the key to the continued use of this nation's huge coal reserves are coal gasification and the pressurized fluid bed. Either or both of these technologies, coupled with a combined cycle will pro-vide the continuing future coal option, while responding to increasingly more restrictive environmental standards. Recent Congressional budget-cutting efforts, however, could threaten the effectiveness of that model program, and ultimately other subsequent government-industry collaboration.

Jan 1, 1996

By G. V. Henderson

Large reserves of high calcium limestone have been outlined in the Redwall formation at Nelson, Arizona. Geologic mapping, core drilling and shallow seismic refraction studies have outlined more than 100 million tons of high quality, chemical and metallurgical grade limestone in the Mooney Falls member of the Mississippian Redwall Limestone. Well developed Karst zones in the Redwall were delineated by field mapping, seismic profiling and core drilling. Development of large reserves of high quality, thick beds of limestone near the present mine and rail facilities was the basis for the current mine and plant expansion. When completed in 1978 the planned 1800 Tpd production will represent the largest lime operation in the Western United States.

Jan 1, 1978

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By K. A. Natarajan, S. Usha Padukone

"An industrial waste liquor having high sulfate concentrations was subjected to biological treatment using the sulfate-reducing bacteria (SRB) Desulfovibrio desulfuricans. Toxicity levels of different sulfate, cobalt and nickel concentrations toward growth of the SRB with respect to biological sulfate reduction kinetics was initially established. Optimum sulfate concentration to promote SRB growth amounted to 0.8 - 1 g/L. The strain of D. desulfuricans used in this study initially tolerated up to 4 -5 g/L of sulfate or 50 mg/L of cobalt and nickel, while its tolerance could be further enhanced through adaptation by serial subculturing in the presence of increasing concentrations of sulfate, cobalt and nickel. From the waste liquor, more than 70% of sulfate and 95% of cobalt and nickel could be precipitated as sulfides, using a preadapted strain of D. desulfuricans. Probable mechanisms involving biological sulfide precipitation and metal adsorption onto precipitates and bacterial cells are discussed.IntroductionIndustrial effluents from hydrometallurgical and mineral processing operations often contain high sulfate and metal concentrations posing significant disposal problems, which require urgent solution to avoid serious environmental contamination. In such waste liquors, sulfate and heavy metals such as cobalt, nickel, zinc and iron originate from the chemical or biological oxidation of exposed sulfide minerals. Reduction of sulfate and precipitation of toxic metal ions from industrial wastes is essential from the viewpoint of environmentally acceptable waste disposal and recovery of associated strategic metals.Many of these heavy metals are essential for metabolic activity of bacterial cells at low levels. But they exert toxic effects at concentrations encountered in polluted water. Removal of toxic metals through biological reduction of sulfates from industrial waste waters have been practiced for several decades. Metal remediation through common physicochemical techniques such as oxidation-reduction, chemical precipitation, filtration, electrochemical treatment, evaporation, ion exchange and reverse osmosis processes is expensive and not suitable in the case of voluminous effluents containing complexing organic matter and low metal concentrations. Further, strong and contaminating reagents are used for desorption, resulting in toxic sludge and secondary environmental pollution. Biotechnological approaches can be more efficient and cost effective for detoxification of such effluents. Biotreatment/ bioremoval offers several advantages over conventional chemical and physical treatment technologies, especially for diluted and mixed contaminants. Biological detoxification, which involves the use of microbes to detoxify and degrade environmental contaminants, has received increasing attention in recent years (Iwamoto and Nasu, 2001). In addition, valuable metals can be recovered from metal sulfide sludge (Boonstra et al., 1999)."

Jan 1, 2015

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By B. A. Barnum

The Chino mine is an open pit copper mine located in southwestern New Mexico, at an elevation of 1890 m (6200 feet) above sea level, approximately 117 km (70 miles) north of the Mexican border. It is owned by Chino Mines Co., a Phelps Dodge Corporation-Mitsubishi Minerals partnership, and is operated by Phelps Dodge Corporation. As part of an effort to maximize production and minimize costs, a computerized truck dispatching system was approved for purchase and installation at the Chino mine in March. 1984. Modular Mining Systems, Inc. was commissioned to install their system, trade named DISPATCH. The system installation was completed and operation began in July, 1985. Installation and operation of the system has presented some interesting challenges and problems, which have been overcome, resulting in increased productivity for the haulage truck and shovel fleets.

Jan 1, 1987

By John M. Hird

Texas Gulf Sulphur Company's Lee Creek Mine has opened a major phosphate mining district in the Central Coastal Plains of North Carolina (Fig. 1). The ore deposit as it is now known was roughly outlined in 1961 by a Texas Gulf geologist using wire line exploration methods. Slightly uraniferous phosphate materials were detected by a slim-hole gamma ray probe run in numerous farmers' water wells penetrating the formations. A follow-up-core drilling pro- gram determined the economic ore limits to lie in the south central section of Beaufort County beneath 70 feet to 120 feet of unconsolidated sediments. The 50,000 acre deposit is known to contain over two billion tons of phosphate ore amenable to strip mining methods. A part of the deposit underlies several thousand acres of the Pamlico River estuary. The 90 million dollar capital investment plant built by Texas Gulf during 1965-66 included a strip mining operation using a 72-yard walking dragline, a three million product ton per year flotation concentrator, four fluid bed calciners, a sulphuric acid plant (acid for captive use), a phosphoric acid plant, and three solid fertilizer material plants. Shipment to domestic markets is by rail and truck and to over- seas markets by barge to a transshipment terminal at Morehead City, North Carolina. Early mining investigations were conclusive first that the phosphate ore could economically be recovered only by dry strip mining methods, and second that artesian ground waters in the formation (Castle Hayne limestone) underlying the ore would have to be controlled. This report will relate the application of ground water hydrology in depressurizing the Castle Hayne aquifer to facilitate dry strip mining at depths 130 feet below sea level at the Lee Creek Mine.

Jan 1, 1970

By Paul C. Schmall

In recent years, several geotechnical methods have been successfully applied to ash pond closure. These include modified dewatering techniques with wellpoints and wells to physically drain the material, soil mixing to create a soil-concrete material for improved accessways as well as improved ground structures within ponds to act as barriers or gravity dams, and geotechnical instrumentation to serve as an early warning of the potential for liquefaction. Given the parallels between fly ash and sluiced in place mine tailings, the application of fly ash remediation method to mine tailings shows significant potential, as illustrated in this paper.

Feb 1, 2024

By Cleland N. Conwell

Intermittent coal mining has been conducted in Alaska for over a century. The first report of coal in Alaska was by the Veechy expedition of 1826 and 1827. Whaling ships used coal from Corwin Bluff near Cape Beaufort during the early and latter parts of the 19th century. The first coal mine in Alaska -- and probably the oldest in the Pacific coast of North America -- was opened by the Russians at Port Graham on the southwest tip of the Kenai Peninsula. The mine was operated from 1855 until 1867 when the United States took possession of Alaska. From 1880 to 1915 coal mining was carried on intermittently at several localities including Unga Island, Herendeen Bay, Chignik Bay, Kachemak Bay, and several points along the Yukon River. Small coal mines along the Yukon River provided fuel for the river steamers traveling from St. Michaels to Whitehorse. The area of sustained coal production began with the completion of the Alaskan Railroad from Anchorage to the Matanuska coal field in 1916 and to the Nenana field in 1918. Coal production continued to increase until 1953, at which time the oil and gas fields in Cook Inlet were developed. Oil and gas eventually replaced- the Matanuska coal as a means of providing heat and power. The military in the Anchorage area shifted from coal to oil in 1967 causing a decrease in production. The increased demand for electric power in the Fairbanks area offset the decline and coal production started to increase. In 1969-1970 the Golden Valley Electric Association constructed a mine-mouth power plant 70 miles southwest of Fairbanks near Healy and a power line to Fairbanks. LOCATION OF COALS IN ALASKA Coals are found in all geographical subdivisions of Alaska. Coal in Alaska ranges in age from Carboniferous to Tertiary, and grade from lignite through anthracite. Figure 1 shows the locations of Alaskan coal fields. The only fields that have been developed extensively are the Matanuska and Nenana. Figure 2

Jan 1, 1972

By T. W. Flemal

Good afternoon gentlemen. To begin, may I say ?thank you? to the AIME for the invitation to be here today to talk about my company's experience with shovel, truck, pocket, to car loading. The other author of this paper is here today. (Introduce John Sweet). Before we get to the details of this paper I want to tell you a little about Erie Mining Company. Erie Mining Company is located on the east end of the Mesabi Range in northern Minnesota and is engaged in the business of processing taconite rock into iron ore pellets. In 1970, the twelfth year of production, Erie will produce its rated capacity of 10.3 million tons of high grade iron ore pellets. The plant is the first of five iron ore pelletizing operations managed by Pickands Mather & Co. with a combined annual production capacity of 21 million tons. This plant began producing high grade iron ore pellets in 1957 placing it among the earliest of taconite production facilities in North America. Historically Pickands Mather & Co. had been a leading natural ore mine managing firm in the Great Lakes region for more than 70 years. Pickands Mather & Co. moved into the new field of taconite mining and processing with management and operational experience from the open pits and underground mines. We were to learn much of volume taconite handling requiring new equipment and new procedures. A trial and error period through the early years of taconite processing developed through the operation of an experimental sized preliminary plant near the present Erie Mining Company site.

Jan 1, 1970

By M. B. Freeman

Acrylic polymers have been found to be effective dispersants and stabilizers in a wide variety of mineral processing applications including rheology control in concentrated slurries. This paper will describe these low molecular weight, water-soluble polymeric dispersants and provide a basis for how they function in concentrated slurries based on computer molecular modeling and applications results. Data on homopolymers as well as copolymers of acrylic acid will be presented to demonstrate the optimization of a polymeric dispersant in preparing high solids slurries of inorganic materials such as kaolin, calcium carbonate, lime, and magnesium hydroxide.

Jan 1, 1996

By W. D. Delahaut

Sampling tests performed at the Paradise Peak Mine compared various blasthole samplers and reverse circulation sampling methods. Statistical analysis of the data indicates that be-low-the-deck bag sampling produced a 24 to 29 percent error when compared to bulk sampling methods. Use of a chip pile wedge sampler reduced error to 17 percent. Reverse circulation sampling upgraded over bulk blasthole sampling by 7 percent for gold and 11 percent for silver. These results indicate that bias sampling conditions exist when small volume bag sampling is employed in production blasthole drilling.

Jan 1, 1991

By C. A. Oestreicher

For sulfide minerals, the presence of dissolved oxygen in the water phase is an influencing factor for separation by flotation. Klassen and Mokrousov(I:217l distinguish three stages of oxygen adsorption; namely, reversible adsorption, activated adsorption and, finally, surface oxidation. While contraversial, limited adsorption of oxygen is believed to improve the interfacial reactivity between collector and mineral. Intensive surface oxidation of sulfide minerals usually results in unsatisfactory flotation with collectors of the xanthate type. The influence of dissolved oxygen in the water phase has received consideration for sphalerite, galena, chalcopyrite, arsenopyrite, chalcocite, and covellite(2,3,4,5,6). However, the nature of surface oxidation products of sulfide minerals has received very limited investigation(6,7). Lightly oxidized galena promotes the adsorptive reaction of surfactant (xanthate or dixanthogen). Tolun and Kitchener(8) state that limited interaction occurs between galena and xanthate under relatively reducing conditions. And, that exposure to oxygen raises the electrochemical potential of the galena to that required for reaction with xanthate or dixanthogen. In the latter condition, the galena has an "effective flotation surface". On the other hand, intensive oxidation of galena reduces the chemical reaction with xanthate collectors (9) . Complete flotation with xanthate-type surfactants with increasing oxygen content in the water phase has been determined to have the following sulfide mineral sequence(3): galena, pyrite, sphalerite, chalcopyrite, pyrrhotite and arseno-pyrite. The work of Cusack(4) suggests that some threshold amount of oxygen is necessary for flotation to occur, but heavy oxidation hinders flotation with xanthates. According to Tolun and Kitchener(8) catalytic oxidation of xanthate to dixanthogen occurs. From infrared studies, Poling and Leja(IO,II) found that in the absence of oxygen in solution, xanthate ions do not adsorb either on

Jan 1, 1972