Search Documents

By Linda Frederick

In July 1997, Krupp Canada obtained the contract to design and supply the conveyor system for Chile's Los Pelambres copper mine expansion project. Progress on the overland conveyor system is currently on schedule. It is a challenging task to convey copper ore from an open-pit mine located on a mountain site 3,000 m (9,840 ft) above sea level down 1,300 m (4,265 ft) to the processing plant at the valley floor below. The Los Pelambres conveyor system moves copper ore at a rate of 8.7 ktlh (9,600 stph) and at a speed of 6 ml sec (1,180 ftlmin) for 12,750 m (41,830 ft). The distance is divided in three conveyors, each 1,800 mm (71 in.) wide. The largest conveyor is 6 km (3.7 miles) long. To protect against avalanches and rockslides, the conveyors run through a 12-km- (7.4-mile-) long tunnel system. The lowest of the three conveyors is equipped with a shuttling head end. With this, the conveyor discharge point can be moved back and forth by 100 m (330 ft), allowing it to build up a longitudinal stockpile at its end. To meet the extreme design parameters, the limits of conveyor design had to be pushed to record-setting marks. For instance, the ST-7800 steel cord conveyor belt is the strongest belt ever installed in a conveyor system. A total drive power of 25 MW (33,535 hp), consisting of 10 2.5-MW (3,352-hp) drives, is included in the design plans. In loaded condition, the electric motors act as generators and feed electric energy back into the power grid. The motors are controlled by variable frequency inverters that provide an infinite adjustment of motor speed. This technology allows starting and stop- ping the conveyors precisely along predetermined acceleration and deceleration ramps. This is done so harmful belt jerking and stress waves can be avoided.

Jan 1, 1999

By J. A. Barsin

Stationary air pollutant sources established prior to the New Source Performance Standard (NSPS) are not, at present, subject to federal emissions regulations. However, proposed legislation could require many existing stationary sources to reduce emissions. This paper will report upon the laboratory work undertaken to date by B&W to commercialize a limestone system for sulfur capture both in pulverized coal and cyclone coal-fired utility boilers. Updates will be provided on the US EPA/State of Ohio/Ohio Edison/B&W sponsored pulverized coal full-scale limestone injection demonstration, and on the EPRI/Baltimore Gas 8 Electric, Atlantic Electric/B&W sponsored laboratory-scale cyclone coal limestone injection investigations.

Jan 1, 1986

By C. A. Young

Cyanide is a toxic species that is found predominantly in industrial effluents generated by metallurgical operations. Cyanide's strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent accidental spills. Various methods of cyanide remediation by separation and oxidation, including photolytic advanced-oxidation processes, are therefore reviewed. Reaction mechanisms are presented throughout the paper. The methods are compared in regards to their effectiveness in treating various cyanide species: free cyanide, thiocyanate, weak-acid dissociables, and strong-acid dissociables.

Jan 1, 1996

By Saul J. Esdalera

The flotation response to amine collector and its adsorption on the mineral surface was studied as a function of pH and collector concentration. The flotation response increased in the order anorthite + intermediate plagih clases + albite, while adsorption of amine obeyed the Freundlich equation r = A.Cn. This adsorption is proposg to be due to a covalent bonding between the AlOH surface pups of the plagioclase altered outer layer and the amino group of the collector. Finally, the study showed thatmtial dissolution of the solid phase provides the necessary conditions for amine attachment on the mineral particles and consequent flotation.

Jan 1, 1980

By B. Denby

Recent advances in Virtual Reality (VR) technology have resulted in major opportunities to improve safety training of mine workers, supervisors and managers. The hazardous nature of both surface and underground environments limits the type of safety training that can be carried out. VR offers the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 1998

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone's lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China's dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996

By R. V. Ramani, K. V. Raj

"The air flow problems in open pit mines are complex. Computational fluid dynamics (CFD) models provide a detailed knowledge of the airflow pattern and velocity distribution, temperature, and pollutant concentration within an enclosed domain of the open pit. A range of turbulent model can be selected for varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithm they use; as a result, prediction varies from model to model. This paper presents a study of pollutant transport in an actual open pit mine under stable boundary layer. The objective is mainly to test two turbulence models using the same input conditions, model constants, and similar geometry. Measured data are used to compare results of the two CFD models, namely, the kappa-epsilon (?-e) model and the Large Eddy Simulation (LES) model. Despite the complex synoptic situations, different meteorological input data and the fast changing conditions, the simulation results from both the models are in good agreement regarding the dispersion of pollutants.INTRODUCTION Modeling of contaminant transport under Arctic air inversion is an important step for an assessment of the amount of pollutants within the open pit. The Airflow in open pit mines is of larger scale and does not follow the principles of pipe flow. The air flow problems in actual open pit mines are thus far more complex. CFD models provide a detailed knowledge of the airflow pattern and air velocity distribution, temperature, and pollutant concentration within an enclosed domain of an open pit. There is no known application of CFD in three-dimensional modeling of air flow in large open pit mines. Two equation RANS kappa-epsilon (?-e) and Large Eddy Simulation (CFD) models, however, have been developed to solve the stable boundary layer (SBL) problems in Atmospheric Sciences (Baklanov 2000, Basu and Porté-Agel 2006, Dop and Axelsen 2007, Bandopadhyay et al. 2014). Because an exact flow situation in open pit mines is not known a-priori, it is therefore, necessary to investigate various turbulent models to identify the appropriate model that would simulate the flow phenomena with reasonable accuracy, and predict the contaminant distributions within the pit. Dispersion models differ in their assumptions and structures as well as in the algorithm they use and, as a result, predictions vary from model to model. Furthermore, it is also important to investigate the behavior of a CFD model in simulating a complex phenomenon such as the transport and distribution of contaminants in open pit mine under Arctic air inversion. The simulation of an enhanced period of turbulence in SBL is of particular interest because traditional air pollution dispersion models cannot explicitly treat such intermittent events, and yet the SBL is often the worst-case scenario in an open pit pollution transport"

Jan 1, 2015

By James P. Odendahl

Missouri is a state rich in mineral commodities. There is a variety of types of mining as well as minerals in the state. Different phases of mining are controlled by a variety of state and federal laws. What I hope to do today is to present briefly some of the interaction and interplay that has occurred in the recent years between the mineral industry and the Missouri regulatory agencies, as well as some of the interactions by federal agencies. First a little history which dates back to the late 1600's. For many years Missouri has been a leader in the production of lead and zinc. In fact, recent studies have indicated that Missouri produces better than three-fourths of the nation's present lead supply. Less well known but important resource is iron mining. Some of these operations were the source of confrontation during the Civil War. Major battles were fought in and around Ironton, Missouri where iron mining has occurred for many years. One of the largest pelletizing operations in the state is currently located within the city of Ironton. Joplin, Missouri, the home of Thomas Hart Benton, the famous Missouri painter, has a history of lead and zinc mining, going back to the later 1800's. Many of the paintings by Benton contain reference to the early days of mining in Missouri. There is a Benton mural in the City Hall at Carthage depicting the early days of lead mining in that area. Later, the center of lead mining moved to southeast Missouri near Bonne Terre and Flat River. The names of the towns in this area reflect the history of mining, examples - Leadington, Old Mines, Rivermines, etc. The history of lead mining in Missouri has been referred to in some detail in various publications(l).

Jan 1, 1977

The Functional Performance Equation for ball milling circuits provides plant staff with a new means to improve circuit performance. However, successful execution of a plant project, with verifiable circuit processing performance improvements, requires a significant number of accompanying steps beyond the equation alone. In order to identify and articulate all these steps, a study with plant staff from two milling operations and a grinding media supplier was undertaken. ?Task analysis? of improving plant grinding performance was carried out. This analysis called for the development of a number of system components, and ultimately yielded a ?Plant Grinding Circuit Processing Performance Management/Improvement System.?

Feb 23, 2014

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

By R. J. McLaughlin

Acid mine drainage (AMD) can occur as a natural phenomenon through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhibit low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations -the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiquitous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treatment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper.

Jan 1, 1996

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By James J. Guesk, Robert W. Reisinger, Timothy C. Richmond

A high-altitude (2,900 m [9,500 ft]) historic underground copper mine in Wyoming is discharging copper-laden water with a neutral pH into an otherwise pristine creek. The Wyoming Abandoned Mine Land program is reclaiming the site under a CERCLA deferral agreement. The clean-up goal is to reduce copper in the mine discharge so that the creek can eventually support a trout fishery. A pilot-scale passive treatment test utilizing sulfate-reducing bacteria has been conducted at the site beginning in summer 1997. Test results show significant reduction in copper concentrations in near-freezing mine water at flow rates ranging to 19 liters per minute (5 gpm)

Jan 1, 2000

By Q. Xu

The adsorption behavior of gold in ammoniacal solutions on to activated carbon has been studied. The gold loading capacity of the activated carbon used in the system and the recovery efficiency by the adsorption were examined. The parameters affecting the adsorption of gold on to activated carbon included temperature, agitation speed, concentration of 'cation and anion as well as that of ammonia. It was found that the maximum gold loading on activated carbon used was about 10 kg of gold per ton of carbon. The recovery of gold by the adsorption from ammoniacal solutions was dependent upon the initial gold concentration in the solution. A recovery of 98% of gold was obtained on to the activated carbon under experimental conditions after 120 hour adsorption. It was also found that the initial adsorption rate was relatively fast compared to the whole period of the adsorption. The apparent activation energy for the adsorption was measured to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on activated carbon was controlled by pore diffusion.

Jan 1, 1995

By Saul J. Escalera

Mechanisms involved in the depression of the sulfides: pyrite, chalcopyrite, galena and sphalerite with potassium permanganate have been investigated. Flotation tests were conducted using potassium amyl xanthate, Z-6, and pine oil in the absence and presence of potassium permanganate at around pH = 6. 5 naturally yielded by the sulfides in the pulp. On the basis of crystal chemistry considerations, the amount of xanthate adsorbed by the sulfides depends on the amount of sulfur and metal ions present on the surface; thus, the avidity of the sulfides for xanthate should increase in the order: sphalerite C chalcopyrite 4 galena 4 pyrite, and the ease of depression response to the permanganate action should be in the same order. Depression of the sulfides in the system occurs primarily due to the removal of the collector ions by the permanganate ions to form manganese dioxide and dixanthogen according to the reaction: 3 M(RX)2 + 2 Mn04 + 4 H20 2 ? MnO2 + 3(RX-XR) + 3 M+2 8OH where M represents the metal ion, RX the xanthate ion and (RX-XR) the dixanthogen molecule. Results seem to indicate that the permanganate ions play a triple role in the system: (1) they convert xanthate ions into dixanthogen, (2) they further oxidize the mineral surface and (3) if present in excess, they may oxidize the xanthate beyond the dixanthogen stage with the formation of CO2, H20 and SO4. All sulfides, except for chalcopyrite, showed a depression response in the order predicted regardless of the order of addition of xanthate and permanganate reagents. Chalcopyrite did not depress as easily; this behavior may be due to the avidity of the colloidal MnO2 to adsorb Cu+2 ions on its surface, this would destabilize the colloid making it coalesce with the formation of a layer of precipitated MnO2 on the surface of the mineral. The presence of this layer would prevent further action of the permanganate ions on chalcopyrite.

Jan 1, 1970

By John W. Rold

These encompass all adverse effects of oil shale mining, processing, and ancillary developments on the environment. Specific problems concern: land, vegetation, wildlife, water, air, population growth, aesthetics and public emotion; and fall into four categories of: land, water, air and emotion. Land includes excavations, spent shale disposal, loss of vegetation and impact on wildlife and domestic grazing, plant sites, buildings and roads, necessary urbanization and the total aesthetic or visual Impact. Water considerations are: requirements for Industrial and domestic supplies, adverse effect of underground water on mining, avoidance of pollution or adverse effect on surface or near-surface water, and the utilization or safe disposal of liquids. Air problems include dust, smoke and stack gas, Public emotional problems include reaction to the above problems, and misconceptions of oil shale country and an oil shale Industry. Government and industry are aware of the problems, and are seeking solutions. Last year, the three affected states studied oil shale environmental problems and solution costs. Colorado estimated environmental costs would add approximately 7% to construction and 7% to operation. The report suggested research in: (1) Water availability and impact; (2) Disturbed lands revegetation and rehabilitation, including spent shale; (3) Environmental inventory and impact; and (4) Regional development and land use planning. Governor Love appointed a 47-person committee representing Industry, government and environmentalists to attack the problems. Research pro-posals were prepared to focus on each problem. $715,000 state, federal and industry money is being committed. Results should provide data for industrial solutions and equitable agency administration.

Jan 1, 1972

By L. J. Habegger

This paper considers the potential water quality impacts of future energy scenarios which project an approximate doubling of coal utilization from 1975 to 1985. The major impacts estimated for coal extraction are related to effluents from unregulated activities (reclaimed areas prior to stable vegetation) and pollutants (e.g., metals and ammonia). Where applicable, the EPA effluent guidelines to be in effect by 1983 reduce the impact of individual sources to low levels. For example, total suspended solids and acidic discharges are to be regulated to levels generally below recommended water quality standards for receiving streams. However, implementation of these guidelines, particularly for coal extraction, has not been demonstrated on a wide scale. Water quality is not expected to be a major constraining factor for increasing capacity of coal fired utility and industrial boilers. Water quality control has not been demonstrated on a commercial scale for coal conversion to synfuels, but adequate control technologies appear to be feasible.

Jan 1, 1978

By T. G. Hayes

Economic and environmental regulations in the coal industry have required companies to evaluate their current blasting method of loosening in-situ coal. This paper will review ripping vs. blasting thick in-situ coal seams, handling frozen active coal stockpiles and proper stockpile conditioning and reclaiming. How basic operating technique can improve job efficiency, productivity and cost per ton.

Jan 1, 1995

By Michael F. Gleason

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek Mine In northern Nevada. After the long negotiations reached an impass over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position.

Jan 1, 1990

By Lawrence L. Davis

This paper describes current research by the Bureau of Mines to develop technology for improving efficiency and productivity in metal/ nonmetal mines. The research program addresses a wide variety of problems associated with each of the major categories of mining: underground mining, surface mining, in situ mining, and premining investigations. An overview of the Bureau's research activities is given with emphasis on underground mining. In particular, two innovative and promising concepts currently under development are described: a unique shaft sinking system that uses an impact hammer for rock fragmentation, and a low-profile, portable crusher for underground hard-rock applications.

Jan 1, 1979