Search Documents

By M. H. Morcali

Pistachio nut shells, an agricultural waste biomass, and Lewatit TP 214, a commercial sorbent, were investigated as adsorbents for the adsorption of platinum from dilute hexachloroplatinic acid solutions. Before the pistachio nut shells were carbonized, adsorption percentage was 65%, whereas Lewatit TP 214 ensured almost 100% adsorption. However, after the pistachio nut shell was carbonized at 1,000° C under an argon atmosphere, the platinum adsorption (%) increased two-fold. The effects of such parameters as sorbent dosage, contact time, temperature and solution pH on adsorption were studied in detail in batch mode. The adsorption equilibrium data were best fitted with the Langmuir isotherm model. The maximum adsorption capacities, Qmax, at 25° C were found to be 38.31 and 33.22 mg/g for the carbonized pistachio nut shell and Lewatit TP 214, respectively. The adsorption of platinum on both sorbents was found to be described by the pseudo-second-order kinetic model. The results indicated that the activated carbon prepared from pistachio nut shells can be effectively used for the removal of platinum from acidic solutions.

By R. Du Plessis, J. D. Miller, D. G. Kotlyar

The low potential hydrophobic state of pyrite in amyl xanthate flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at Newmont’s Lone Tree Plant in Nevada. The N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Each of these issues is being studied in detail and research progress is discussed herein.

Jan 1, 2002

By Michael Harris, David Mosch

The numerous small high grade gold and silver deposits of the Front Range Mineral Belt have been uneconomical because of the high costs of mill construction, transportation, and smeltering. Processing of these ores must be simple, cheap, with satisfactory recoveries, and be environmentally acceptable. Vat leach with direct electrolytic recovery satisfies these parameters. A battery of testing was conducted utilizing bottle and bucket tests. A five ton vat leach with direct electrolytic recovery gave excellent results while a five ton heap leach proved impractical due to channeling.

Jan 1, 1987

By Rodrigo Peroni, Euler Victoria

Knowing the depth of contacts between weathering zones in phosphate mines is determinant to define the stripping ratios and the mineralized zones. Contacts are gradational and difficult to define even in the drillhole samples, so the combination with geostatistical simulation techniques helps to define the contact zone and the grade distribution, providing a way to assess the probability of the occurrence and the positioning of contacts between the barren waste and the ore zones. These inputs are used in the scheduling, anticipating risks associated with mine planning scenarios. The results from an application to a case study showed a good improvement when compared to traditional techniques.

Jun 25, 2023

By K. Perry, B. Lusk, Q. Huang, R. Honaker

"Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. The application is conducted either dry or wet. Both methods have advantages and disadvantages however the formation of caked rock dust particles is cited as a significant concern for wet applications. A study was conducted to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid (OA) and sodium oleate (NaOL). At a NaOL dosage of 2 lbs/ton, a contact angle of 112o was measured indicating strong surface hydrophobicity and ability to repel water. FTIR studies indicated a chemisorption mechanism which is necessary for long term stability of the surface modification. The dispersion rate of the modified rock dust samples was elevated by the application of both OA and NaOL thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed a 79% reduction in the dust explosion potential relative to untreated rock test applied by the wet technique. INTRODUCTION Mine explosions have been a long-time threat to underground coal miners attracting significant attention to the accumulations of combustible dusts and gasses. In the presence of sufficient oxygen and heat, the accumulations of combustible dust and gass can lead to large-scale underground coal mine explosions [Harris et al., 2010]. To alleviate the problem, rock dust such as limestone can serve both as a thermal inhibitor and a heat sink to inert the coal dust explosibility thereby prohibiting the occurrence of dust explosions [Richmond et al., 1975; Amyotte et al., 1995; Dastidar et al., 1997; Man et al., 2009]. The dispersibility of the rock dust is an important characteristic that determines the degree of explosion prevention [Greenwald et al., 1938; Mozumdar et al., 1974; Amyotte et al., 1995]. Unfortunately, the environmental conditions of an underground mine has the potential to cause caking of the rock dust which reduces the dispersive characteristics needed. The dispersive property of rock dust can be enhanced by modification of the particle surface properties by the application of chemical additives [Greenwald et al., 1938; Mozumdar et al., 1974; Spence, 2004; Vogt, 2011; Doidge et al. 2014]. The major mechanism for rock dust caking is the adsorption of water which forms liquid bridges at the particle-particle contact points where saturated solutions of soluble powder ingredients are present. Changes in temperature or relative humidity result in solvent (water) evaporation and the formation of dry bridges [Rumpf, 1958; Specht, 2006]. One method to prevent caking is creating hydrophobic rock dust to repel water from the solid surface thereby preventing the formation of liquid and solid bridges."

Jan 1, 2015

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be "land poor" but "coastline rich," meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. The Independent State of Papua New Guinea (the State) recognizes this tremendous opportunity and is taking a leadership role in this emerging industry by becoming a 15% partner in Solwara 1 (with an option to increase their investment to 30%).The Solwara 1 Project has been gaining momentum since Nautilus Minerals and the State signed an Agreement on April 24. This new agreement with the State in which they have staked a minimum 15% interest as a meaningful partner, underscores the State’s continued and widespread support for the Project. Signing of this Agreement was a historical occasion and a milestone achievement for Nautilus Minerals and the people of PNG.The machinery being built for the Solwara 1 Project is taking shape. The Seafloor Production Tools are now over 90 percent complete. Assembly of the biggest tool, the Bulk Cutter, was completed in April this year and assembly work on the Collecting Machine and the Auxiliary Cutter commenced in May and June this year respectively. The Riser and Lifting system, which will be used to transfer the mined material from the seafloor to the surface within an enclosed system, is over 50 percent complete. The critical path for the Solwara Project is to secure a suitable vessel arrangement. Nautilus aims to have this completed by the end of this year."

Sep 1, 2014

By Oluwasegun Samuel Odebiyi, Shaona Wang, Feng Gao, Biao Liu, Hao Du

Recovering vanadium from vanadium titanium-magnetite (VTM) ore using ( NH4)2C2O4 is a clean hydrometallurgical process, but the drawback is the low recovery and slow kinetics due to the formation of inhibitor. A novel energy-efficient mathematical model was derived for green leaching of VTM in which the mechanical activation (MA) removed the inhibitor “δ” (formation of impermeable product layer of CaC2O4) covering the reacting core of the CaV2O6 leaching process in ( NH4)2C2O4 solution. Before the MA processing, the formation of the CaC2O4 layer affects the kinetics (slow) and NH4VO3 leachability (low recovery). The dissolution rate enhancement and economic importance (in terms of leaching kinetic/recovery) of mechanical activation (MA) pretreatment in hydrometallurgical processing cannot be overemphasized. It is shown from the experimental and developed mathematical model results that the rotating speed of the ball mill (ωb) has a significant effect on the NH4VO3 recovery. At 360 rpm, the experimental result gave an 82% optimum recovery rate and a reaction rate constant of 0.01889s−1 with close correlation with the present models at 82.8% and 81% for liquid-to-solid layer diffusion and chemical reaction controls, respectively, with a reaction rate constant of 0.018883s−1. The close correlation between the experimental recovery rate results and the diffusion recovery rate model result justifies that the leaching process is diffusion control shrinking core kinetic with experimentally measured activation energy (Ea) value of 19.502 kJ/mol . This present model proved that MA enhances the dissolution rate regardless of the formation of a passivation layer on the material and best describes the kinetics of the MA hydrometallurgical processes compared to the shrinking core model.

Nov 3, 2023

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By W. K. Callaway

The need to increase ore recovery and pillar stability caused the Magmont Mine staff to investigate the use of sandfill to accomplish both tasks. The use of hydraulically stowed classified mill tailings as a subsidence preventative will be discussed as well as the use of sandfill in pillar recovery and as a part of the regular mining cycle.

Jan 1, 1986

By Heiner J. Sander

Stanford University operates the National Research Facility which is located at the Stanford Linear Accelerator Center (SLAC) in Menlo Park, California. In order to improve and allow for enhanced experiments, the current facilities required expansion. A1500 foot long tunnel (20 ft wide by 21 ft high) and a 220 foot long underground cavern (49 ft wide by 32 ft high) were excavated through the Ladera Sandstone formation which is an intermediate geo-material with week rock properties. The overburden between surface and crown of the structures varies from 10 to 80 feet. The underground structures were excavated according to the principles of the NATM (New Austrian Tunnel Method). This paper addresses the challenges that were encountered during the construction phase of the project and how construction issues were resolved mutually by the owner, engineer and contractor. The implementation of geotechnical instrumentation, recorded data and interpretations, soil conditions and behavior encountered during construction are also presented.

Jan 1, 2008

By H Vigil, G. Peach

Long tunnels with only one access shaft pose many program problems for logistics, combine these with the requirement to drive directly out under the seabed for 10.2 km, and the program issues become even more challenging. The Musaimeer outfall tunnel was one such tunnel and to meet and eventually improve on the planned completion date required a complex and extensive management of all tunnel logistics required to support consistent tunneling for a two-year period. This technical paper will discuss the management issues and solutions implemented to meet the challenges of the Outfall tunnel construction.

Dec 1, 2022

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By LUIS ALBERTO TORRES-CRUZ

The Plewes method is relatively well known among geotechnical engineers interested in assessing the liquefaction potential of soil deposits. Furthermore, it was one of the four methods considered in the post-failure investigation report of the Feijao Dam I, also known as the Brumadinho Dam, in Brazil. The inclusion of the method in that report is likely to increase its visibility among geotechnical practitioners tasked with assessing the liquefaction potential of tailings. While the authors of the method duly presented it as a screening method, more recent technical literature contains conflicting views on its reliability. Considering the popularity of the method and that the safety record of tailings dams is a cause of great concern, this study assessed the uncertainty of results from the Plewes method. The study concludes that, even under optimistic assumptions, the results of the method are too uncertain for detailed characterization of tailings deposits.

By William R. Bush

This paper is a presentation of findings based upon an econometric model of the world zinc industry. The model was developed as a simple but useful aid for long-run forecasting and planning purposes. A structure was developed for both simulating real zinc price effects on production and consumption, and for forecasting long-run annual zinc prices and supply/ demand levels. Moreover, a methodology is provided to incorporate the effects of: (1) historic technological advances in zinc supply, and (2) the development of the competitive plastics industry. Finally, reduced form equations are used to generate ex post forecasts to evaluate the model's performance.

Jan 1, 1979

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By John Kinneen, Sunghoon Choi, Arne Fareth, Edward S. Barboe, Kyle R. Ott

A new water treatment plant is to be constructed for a portion of the water supply system of New York City. The project includes construction of new water conveyance tunnels crossing perpendicular and sub-parallel to the existing pressurized water tunnel at two locations. A study was conducted to evaluate the impact of new tunnel construction on stability of the existing tunnel and hydrojacking potential in the surrounding rock mass. This paper introduces a practical approach to evaluate tunnel interaction, expressed in terms of rock-liner interaction, stress-induced stability and hydrojacking failures. A simple method to evaluate hydraulic and mechanical properties of concrete liners and jointed rock mass is also presented.

Jan 1, 2007

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By S. Ersayin, I. Iwasaki

Application of a magnetic field was shown to be effective in controlling iron losses in pilot-scale cationic silica flotation in the processing of magnetic taconite concentrates. The design of a magnetic field distribution device and batch flotation test results using a 1.42m3 (50 cu. ft.) WEMCO cell are reported. Major losses of iron units in froth products were in the -25µm (500 mesh) fraction, and the application of a magnetic field decreased the flotation of fine magnetite, thereby improving the selectivity of separation. The “as received” sample was sufficiently magnetized and no further benefit was gained by magnetizing treatment. Selectivity was somewhat adversely affected by demagnetizing the sample, though its effect was minimal due to the magnetic field. The device is simple in construction, low cost and may be installed readily in existing equipment.

Jan 1, 2002

By Robert E. Mclvor

Classification system efficiency (CSE) is a simple metric that can be used to measure and increase ball milling circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target (oversize) particles. This paper describes CSE analysis conducted for a variety of operations with related improvements in circuit efficiency ranging from 3 to 30 percent. The achievable CSE for any given ball milling circuit is described, providing the means to determine the extent to which every plant can benefit from increasing grinding circuit CSE.

By W. Collingwood, K. V. Raj, S. Bandopadhyay

In the mining industry, computational fluid dynamics (CFD) modeling is used extensively to simulate air flow in underground mines. CFD modeling of pollutant transport in openpit mines is relatively new. Modeling the actual pit geometry of an openpit mine and the open domain is complex. The complexity is primarily due to the faceted geometry of an openpit mine with its numerous associated sharp features. Important issues that are not considered carefully at the geometry level are generally propagated to the subsequent processes. Several challenges and pitfalls are encountered in modeling pollutant transport in openpit mines. These challenges and pitfalls are related to the geometry, meshing, boundary conditions and turbulence modeling parameterization. An appropriate mesh selection is critical. A detailed discussion of the meshing of the domain of an openpit mine is presented in this paper. The selection of an appropriate turbulence model, such as kappa-epsilon (κ-ε), large eddy simulation (LES), Reynolds stress model (RSM), etc., to obtain the best possible solution is equally significant. This paper discusses the various challenges in modeling the pollutant transport process in an openpit and some of the approaches adopted to address these challenges.

Jan 1, 2013