Search Documents

By E. V. Bowman

This paper is intended to deal with the material handling aspects of fine coal cleaning as applied to a recently built plaint in: southern West Virginia. This plant is processing 160 tons per hour of 1/4" x.0 coal on a two shift basis. Past experience with this very friable low volatile metallurgical coal indicated that its plastometer readings, varied directly with the size and length of time elapsing between mining' and ultimate consumption. Due to the mines location with, respect to its consumers, little could be done to decrease the time element. Studies indicated that the plastometer readings are considerably less in the minus 60 mesh range than that experienced in the plus 60 mesh sizes. Therefore, handling the coal in such a manner as to have the least amount of degradation became extremely important.

Jan 1, 1961

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By R. Freer

Recent developments in expanded PTFE membrane filter cloths offer high flow rates and sub-micron particle removal. These high strength, industrial grade filter cloths can be tailored for tubular filters, leaf filters and rotary vacuum drums. Filtration techniques using tubular filters make possible filtration of difficult slurries with the elimination/reduction of filter aids and chemical additives. This paper describes principles of surface filtration, applying the membrane filter cloth and comparisons to gravity separators. Benefits to the mining industry include clear effluent, enhanced solids recovery and accelerated cost payback.

Jan 1, 1996

By W. Lin

When a large area of open gob collapses suddenly, a windblast is produced that can cause considerable damage throughout the infrastructure of a mine. In a few cases, the windblast has been accompanied by ignitions of methane and/or coal dust. This paper describes the conduct and results of laboratory tests involving the compression of mixtures of air, methane and coal dust under a falling weight and while allowing controlled escape of the mixture. The transient responses on pressure and temperature sensors were recorded. In addition to an analysis of those records, the paper highlights those conditions in which ignitions occurred.

Jan 1, 1997

By Dan Norrgran

In recent years, a great deal of attention has been focused on developing mill liners to increase wear resistance, improve grinding efficiency and reduce energy consumption in milling applications. The installation of an appropriate mill liner is critical as it affects the overall cost and product quality. A mill liner has two specific functions. The first is to protect the mill shell and mill ends from direct contact with the abrasive grinding media (in this case, the liner serves as a wear surface). The second function is to transport the grinding media, creating energy for size reduction. The liner acts as a lifter, mechanically transporting and cascading the grinding media. The mill lining is a major cost in the milling operation. The costs associated with the mill lining include the capital cost of the lining, downtime required to replace the worn liner and the labor for installation. Generally, in hard rock mining, the life of a mill liner in secondary ball mills is 12 to 24 months.

Jan 1, 2009

By V. K. Kakaria

As you know most of the gold and silver is produced by one of the following processes: (1) Agitated Leaching - Carbon adsorption or Merrill-Crowe (2) Heap Leaching - Carbon adsorption or Merrill-Crowe The figure 1 shows a typical flowsheet for recovery of gold and silver using Agitated or Pachuca Leaching Operation. The ore is crushed and ground and then leached in cyanide tanks solution using either Pachucas with air agitation or tanks with mechanical agitation. The soluble metal values are separated from the pulp by counter-current washing. The precious metals from cyanide solution are either recovered by zinc dust (Merrill-Crowe Process) or by loading on carbon and stripping with hot caustic cyanide solution. Gold and silver are electrowon on steel wool cathodes.

Jan 1, 1981

By C. M. Walck

The Rosebud district is located in the Kamma Mountains, southeast of the townsite of Sulphur, Nevada. Since discovery in 1989, LAC Minerals, in joint venture with Equinox Resources, has delineated a resource containing approximately 570,000 ounces of gold and 5,500,000 ounces of silver. The deposit is of the volcanic-hosted epithermal quartz-sericite type. Mineralization occurs in tabular zones in and along the hanging wall of the South Ridge fault, and in cross-cutting high-angle structures. Multiple stages of discontinuous stockwork gold-and silver-bearing quartz-calcite-clay veins cut variably clay-altered, silicified, and sericitized rhyolitic Miocene volcanic rocks.

Jan 1, 1993

By D. W. Jahn

Road construction in the near future will require contractors to guarantee that a project will remain trouble free for years after the project has been completed. These guarantees will challenge aggregate producers to become technically proficient in judging performance of their products. Testing procedures are described that may be used to predict performance of concrete and asphalt pavements before being committed into a construction project, and may also be used as quality assurance tools during construction to monitor performance as construction proceeds.

Jan 1, 1995

By Clement K. Chase

Although flotation is the generally accepted process employed to recover gold and silver as well as copper, lead, and zinc from primary sulfide ores, the metallurgical requirements for the treatment of massive sulfide ore deposits differ markedly in many respects from those employed for the more common disseminated porphyry deposits. In Arizona, some properties classified as other then massive sulfide deposits because of mining and geological characteristics have produced mill-feeds similar to those from massive deposits. Several such occurrences are noted. The process requirements for massive sulfide deposits and unique mill-design implications are discussed in the perspective of world-wide economic considerations and the individual regional metallurgical and economic constraints in the United States.

Jan 1, 1986

By Donald M. Ulbrich

As all of us know, the "heat" is on for western coal. The need for western coal is critical if the nation is to reach the goals of Project Independence by 1985. Without the development of western coal, the goals will not be met. It's that simple! That's because 50 percent of our nation's coal reserves lie in the states of North Dakota, Montana, Wyoming, Colorado, New Mexico, Arizona and Utah. And surface mining is the key to unlocking these reserves. Of the nine states in the coal provinces, five-Wyoming, Montana, New Mexico, North Dakota and Arizona-are the best examples since surface mining accounts for 88 to 100 percent of the coal mined in each of these states. Collectively, their annual production more than doubled between 1969 and 1972, rising to 35 million tons per year. And, taken individually, each state's production has more than doubled, also. Total annual production from these five key states could very well exceed 180 million tons per year by 1980-four times the 1972 production level. The biggest producer among the five is Wyoming. Wyoming's production tripled since 1969 to nearly 14 million tons in 1973. So the heat is on for western coal, especially from Wyoming. Now we come to the question of how to mine this increasingly precious mineral. What are the available methods? First, let's take a brief look at several characteristics of western coal deposits.

Jan 1, 1975

By Farlow C. Davis

Magma Copper Company, San Manuel Division, is a wholly owned subsidiary of the Newmont Mining Corporation and located at San Manuel, Arizona. The ore body is a dessiminated porphry copper deposit in quartz monzonite. The primary copper mineral is chalcopyrite with minor amounts of chalcocite, bornite, and covellite. The molybdenite occurs mainly on fracture faces or else associated with quartz veinlets. Pyrite is the major sulphide mineral in gangue. The feed to the concentrator from the underground mine is approximately 0.720 percent copper and 0.029 percent molybdenite. The concentrator has a design capacity of 62,000 tons of ore daily. After a standard ore treatment circuit consisting of grinding, rougher flotation, regrinding, and cleaning, a bulk concentrate is produced which contains 27 to 29 percent copper and 1.0 to 1.2 percent molybdenite. This concentrate is pumped to the molybdenite plant feed thickener.

Jan 1, 1977

By E. B. Graves

I have been asked to talk to you this morning about phosphate marketing and distribution. In discussing this I will attempt to answer such questions as: What is phosphate? Where do we get it? What form is it and how do we sell it? How do we distribute it? How is it applied? And last, but not least, What about the future? To start with, phosphate is one of the three primary plant nutrients. It is the element essential for root structure of plants. Plants, like humans, need a balanced diet. Thus, the amount of phosphate required by individual plants is, in part, related to how much of the other nutrients are used. Virtually all soils contain a certain amount of available phosphates. Back at the turn of the century the most common source of additional plant nutrient, including phosphates, was from cattle manure. The use of chemical fertilizers is something that has grown significantly during the last half century, and in particular, the last 20 years.

Jan 1, 1977

By D. Marsh

The feasibility study for the Grasberg Block Cave mine, finalized in May 2008, indicated a production capacity of 160,000 tonnes per day. A rail haulage system was an integral part of the mine design. This paper describes the simulation process used in optimizing the design and discusses the key factors and variables that impact the capacity of the system. The final recommendations for the haulage level layout and associated equipment are also included.

Jan 1, 2010

By Alexander N. Winchell

"The waters of Lake Superior flow into those of Lake Huron through the St. Mary's river. The rapids in this river are about half a mile wide and three-quarters of a mile long, in which distance the fall amounts to about twenty feet. Since this was the only obstacle to navigation between the west end of Lake Superior and ports on any of the other Great Lakes except Ontario, attempts were made many years ago to permit the passage of small boats from Lake Huron to Lake Superior by means of canals and locks. The first canal was built on the Canadian side of the river by the Northwest Fur Company in 1797-98. The lock was 38 feet long, 8 feet 9 inches wide and had a lift of 9 feet. A tow path was made along the shores for oxen to track the bateaux and canoes through the upper part of the rapids., The lock was destroyed during the war of 1812 by United States troops from Mackinac Island.The first ship canal, known as the State Canal, was built on the American side of the river in 1853-55, about 750,000 acres of land in Michigan having been granted by congress to a private company as a 'concession for its construction. This canal was more than a mile long, 65 feet wide at the bottom and 100 feet wide at the water's surface. It had two locks, each 350 feet long by 70 feet wide, with a lift of about 9 feet. The depth of water in the canal was about 13 feet and in the locks about 11 1/2 feet."

Jan 1, 1920

By J. E. Bevan

Once mining compromises the stability of a rock mass, the dangerous task of roof bolting begins. Many attempts have been made to automate this process, but there are still many refinements that need to be made. In the past, roof bolting modules were designed around the abilities of a human operator. Currently, researchers are taking a new approach that focuses on designing modules that can utilize bolting methods that are easily automated. A non-rotating anchor that is locked into position by a linear force (as opposed to a rotational force) was designed by researchers at the U.S. Bureau of Mines. Once the bolt is secured in the bolt-hole by the anchor, the bolt is tensioned and a collet is used to secure the other end of the bolt. This process replaces the traditional bolt-nut fastening method. This program is part of an effort at the U.S. Bureau of Mines to automate the coal mining process.

Jan 1, 1994

By T. B. Szwilski

The paper gives an account of the development of a mine health and safety program in China from 1987 to 1996. The project was funded by the United Nations Development Program and managed by the International Labor Office (ILO). The objective was to strengthen the capability of the National Safety Training Center (NSTC), located near Beijing to train more than 2,000 engineers per year, and provide consulting and informational services to 39 safety training centers and coal mines. Presently China has the highest mortality rate in the world for coal mine operations, the greater incidence occurring at the many thousands of small, unlicensed underground mines.

Jan 1, 1998

By A. M. Gaudin

At the 1971 Annual Meeting we presented a paper on the results s obtained by wet magnetic separation on very fine, slightly magnetic material . Considerable interest was shown in a corollary subject, namely; on the type of magnetic con¬struction of the Magnetic Engineering Associates (MEA) high-intensity magnetic separator (HIMS). it is the purpose of this paper to describe the principles of this separator and to give answers to many of the questions directed at us both in session and privately since the March 1971 meeting of the AIME. It is well-known that passage of a direct electric current through a wire shaped in the form of a loop results in a magnetic field being created in the volume enclosed within the loop. The magnetic field is proportional to the amperes of electric current passing through the wire. If the wire is in the form of a solenoid consisting of 11 turns, the magnetic field is n times larger. Hence the expression ampere-turns commonly associated with magnetic separators. If a particle, free to rotate and of higher magnetic susceptibility than the medium, is placed in a magnetic field, it will orient itself within that field, and it will move within the field in such a way as to go into a more intense part of the field. The traction on the particle is proportional to its inherent magnetic property which depends on its magnetic susceptibility and its volume, to the mag¬nitude of the field at the spot where the particle is situated, and to the magnitude of the field gradient at that spot. Of the three factors that control traction on a particle in a magnetic field, the magnet designer can effectively control two, the magnetic field and the field gradient. In a wet magnetic separator such as the HIMS magnetic separator, there is another force exerting traction on the particle, and that is the force of the fluid (liquid) on the particle. It is, therefore, essential to examine the relationship of the fluid to the magnetic field. First, assume the water in which magnetic and non-magnetic particles are suspended to be stagnant. In the absence of magnetic field, the only forces acting on the particles are those due to gravitation on the particles and on the fluid displaced. This is the subject, so important in gravity concentration, discussed in elementary texts of mineral engineering'.

Jan 1, 1972

By S. J. Jung

The stability of underground openings for deep mines is critical, since incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress concentrations. Current state-of-the-art procedures for the design of underground openings are largely based on rules of thumb, experience, and trial and error. Rules of thumb are invariably based on the past experience of the designer and may not remain optimal as the depth and complexity of mine workings increase. Often, as conditions change, and as the interaction between geology, in-situ stress conditions, and mine openings grows more complex, the cost of maintaining structural integrity becomes prohibitive. Existing design procedures for deep mines are rapidly becoming inadequate as mines are worked at greater depths. For example, in the Coeur d' Alene Mining District, several million dollars are spent for inspection, repair, and maintenance on a regular schedule, largely as a result of inadequate design. In these types of situations, it is of critical importance that a new design methodology be developed for the layout and design of underground openings.

Jan 1, 1994

By A. E. Michon

My comments today are directed toward western coal and its impact on Burlington Northern. I will be discussing three major topics. These are: location and extent of mining activities, the flows of this coal traffic into the various market territories, and finally the interaction of this western coal with coals found in the balance of the United States. When we at BN speak of western coal, we refer to those substantial deposits lying in southeastern Montana and north-eastern Wyoming. This territory covers many different coal formations. For the sake of simplicity, I will be referring to this general area as the Powder River Basin (or the "western" coal fields). This slide highlights the area overlayed by a map of the BN rail system. The U.S. Bureau of Mines estimates the demonstrated reserve base of Montana and Wyoming to be approximately 176 billion tons. Of this figure, about 73 billion tons is minable by surface methods. This is roughly 72% of the total strippable reserves in the western united states, BN does not have sole access to this coal for there are deposits in southern Wyoming near the union pacific railroad. I will say more about this later.

Jan 1, 1978

By H. Ankara

Determining the identicalness levels of the same model trucks working in open pit mine transportation system by means of statistical analysis methods is very significant in terms of availability analysis. In this study, the identicalness levels of two trucks picked randomly from the 170-short-tonne truck fleet working in open pit coal mine over one-year period were examined through a non-parametric test, Mann-Whitney U test for two samples. Time to failures (TTFs) and Time to Repairs (TTRs) of the trucks were analyzed with this test technique and then whether they were identical or not was determined. In order to determine whether the trucks identified to be identical at the end of this test displayed the same mining performances within the same open pit transportation system, the availability analysis of the identical trucks was carried out. As a result of the availability analysis, it was observed that the trucks had availability values that were very close to each other. It was also determined that Mann-Whitney U test could be employed together with availability analysis. Finally, it was observed that Mann-Whitney U test for two samples could yield rapid results in the performance analysis of complex systems like open pit mines.

Jan 1, 2010