Search Documents

By G. E. Karantzavelos

Introduction Pure alunite (KAl3 (SO4 )3 (OH)6 ) contains 37% A1203. In the alunite ore found on Milos Island, Greece, opal is the principal gangue while some aluminum, iron, and titanium oxides are also present. Processing of alunite ore leads to the recovery of potassium sulfate, alusil (alumina-silica mixture), and sulfur dioxide. An interesting process has been developed in Greece (Svoronos, 1977) consisting mainly of roasting the alunite ore mixed with KCl to disrupt the mineral lattice in preparation for separating its components. The thermal decomposition of alunite at approximately 600°C occurs by the reaction: KAl3 (SO4)3 (OH)6 + nSiO2 + 6KC1 - 4 K2SO4 + 3 A1203 . nSiO2 + 6 HCl + 3H20 According to the process pure alunite mixed with 543 kg KCl, 840 kg K2SO4, 370 kg alusil, 264 kg HCl, and 65 kg H2O are produced. The roasted calcine is leached in hot water. The potassium sulfate leach slurry is then thickened and washed to obtain a solid residue (alusil) plus a solution rich in potassium sulfate. Assuming the alunite ore feed consists of 50% to 60% alunite, the solid residue might consist of approximately 22% to 27% A1203, silica, iron, and titanium oxides. This leach residue could be digested in a hot sodium hydroxide solution to dissolve alumina. An amount of the alumina (approximately 10%) would not dissolve. In addition, part of the silica would dissolve requiring removal from the solution in a subsequent desilication operation. The same leach residue could be attacked by mineral acids such as a diluted hydrochloric acid to extract aluminum chloride (Sawyer et al., 1983). Alumina and aluminum are presently produced from bauxite of which Greece has important reserves. If this aluminous material (alusil) could be beneficiated by any physical process, then it would be considered as a raw material for the production of fire-clay refractories instead of an alternate source of alumina. Experimental procedure Extensive laboratory work (mineralogical and chemical analyses) indicates that alusil is a mixture of liberated (mostly) alumina and silica particles, not a natural silicate mineral. Table 1 shows the chemical assays of two alusil samples that were obtained from a roasted alunite ore leaching pilot plant. The samples used for the experiments were a very fine alusil powder (K80 = 400 mesh, 38 µm). These were pulped in tap water. Desliming of the pulp before each flotation test was ineffective. Flotation tests were performed in a 2000 ml Denver cell. A standard 500-g sample was first conditioned at a pulp density 50% solids for 5 min with hydrofluoric (HF) acid solution (40%). The temperature of the conditioned pulp was measured and kept nearly constant at 50°C. The pH of the conditioned pulp was also regulated to 2.5-3 with HF solution. Then ARMAC C solution (2%) as well as two drops of fuel oil and one drop of AEROFROTH 65 were added and the pulp was reconditioned for 2 min. After conditioning, the viscous pulp was transfered to the flotation cell. It was then diluted with warm water to about 15% solids and floated to separate silica from alumina particles. A rougher froth product that was cleaned and recleaned was obtained from the flotation tests.

Jan 1, 1987

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

By D. C. Torre

Since the early 1960s, there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the successful continuous haulage systems were placed in operation in the early 1970s. These were all of the bridge conveyor type. They usually consisted of bridges and mobile bridge carriers (MBC) attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor continuous haulage systems are either of the belted or chain type. The most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Co. Until early 1977, Jeffrey Mining Machinery Division manufactured and marketed the most successful chain conveyor type haulage sys¬tems. In 1977, Long-Airdox reentered the market with a chain-type system to complement its belted system. The original bridge-type continuous haulage system was introduced to the coal mining industry in the early 1960s by the old Long Co., a predecessor to the current Long-Airdox Co. These original units were of the chain conveyor type. In the early 1970s, there were also developments in continuous haulage, employing different material handling media. These in¬cluded the Serpentix, a flexible type belt, introduced by the Joy Manufacturing Co. There was also a serious attempt to introduce hydraulic-type continuous haulage by Consolidation Coal Co. and Conoco Research. Despite some startling successes, particularly with the bridge-type haulage systems, the general and widespread application of continuous haulage has eluded the mining industry. Some of the problems are related to underground conditions; others to people, both management and labor. One of the greatest obstacles to universal success continues to be the difficulty of accepting the philosophy as well as the machinery of continuous haulage. Nevertheless, efforts continue to spread the success of commercial and viable systems in the industry. There is also effort to improve on these systems, and on methods for their successful use. In addition, efforts continue, with private and public support, to develop new types of continuous haulage equipment and systems. Bridge Type System Developments Because they have already been successful in some US and overseas mines, new developments in bridge-type systems will first be touched on. The Long-Airdox Co. has continued to improve both its belted and chain continuous haulage system. In the belted system, the company recently introduced a new design that will be mainly applicable in higher coals and in noncoal mining applications, as shown in the accompanying figure. This new system is equipped with 305-mm-diam (12-in.-diam) pulleys in the bridges and mobile bridge carriers, in place of the 150-mm-diam (6 in.-diam) pulleys in the standard system. The modification is designed primarily to improve belt life and keep belt problems to a minimum. An operator, the Clinchfield Coal Co., a Division of Pittston Coal, developed the detaching of the bridge-type continuous haulage system from the miner by placing a mobile bridge carrier at the head of the string. However, Long-Airdox and Jeffrey have now made this an option to their at¬tached-type system. In the US, there are many chain type haulage systems detached from the miner with an extra MBC at the head. There are two such belted systems

Jan 7, 1982

By D. M. Bodily, V. J. Hucka

INTRODUCTION Interest in the recovery of methane from coalbeds has increased rapidly over recent years, because of its potential as an energy resource and to alleviate pollution and safety problems. The resource base of coalbed methane in the United States has been estimated at 11.2 Gm3, roughly equivalent to 20 years consumption (Mroz et al., 1983; Kuuskraa and Brandenburg, 1989). Methane contributes to the adverse environmental impacts of global warming, tropospheric ozone formation (smog), and potentially stratospheric ozone destruction. Association of methane with coal has always presented a safety problem in mines due to the potential for explosions. The rate of release of methane depends on the amount adsorbed by the coal, the adsorption isotherm for the coal, and the size of the coal particles. Mining operations can affect the particle size distribution and the production of fines and therefore the rate of release. The time the mined coal remains in the mine may also be important in determining total emissions. The methane content of some Utah coals was determined in this study. The methane content of the coals is compared with the chemical and physical properties of the coals and the properties of the seam and neighboring strata. Correlations are developed to better understand the formation and retention of methane by these coal seams. METHANE FORMATION IN COALBEDS Three mechanisms for methane formation may be considered: (1) nonbiogenic formation, (2) formation by anaerobic bacteria during plant material deposition and the early stages of diagenesis, and (3) formation from pyrolysis of coal material during coal maturation. Nonbiogenic formation by thermal processes involving carbon- and hydrogen-containing compounds has been proposed as a mechanism for methane formation in the earth. It is not likely to be of importance where other fossil fuel materials are present. Coal would not survive the temperatures required and hence the methane would need to migrate and be trapped by the coal seam. This mechanism is unlikely for coalbed methane. Formation of methane by anaerobic bacteria undoubtedly occurs during coalification, but the methane may not be trapped until the pore system of the coal is developed, and would likely be displaced by methane formed during further coalification. Methane formed by maturation of the coal material as it progresses from peat to coals of various rank is the most probable mechanism for the formation of coalbed methane. Most of the methane is adsorbed onto the walls of microvoids in coal. It has been estimated that the surface area of one kilogram of coal is between 20,000 m2 to 200,000 m2. Surface area measurements depend on the coal and also on the method of measurement. At 20 atmospheres, in some coals, the adsorbed methane is 10 times greater than methane as a free gas. At 100 atmospheres the adsorbed gas can be as densely packed as a liquid. The volume of methane gas held in coal depends on the volume of gas that exists as a free gas and the adsorbed gas capacity. The volume of free gas in the coal can be calculated from the kinetic theory of gases (methane can be assumed to be an ideal gas because errors would not be greater than 1 % for normal mining pressures). Langmuir (1916) derived an equation for the adsorption of gases on uniform surfaces and this is applied to the adsorption of methane on coal:

Jan 1, 1993

By Leonid Pevzner, Valerie Dmitriev, Yuri Babitchev

Performance of belt conveyors, service life of belts and mechanical elements can be radically improved if the automatic adjustment of the belt speed movement is made in such a way, that the unit load over the conveyor length be constant and close to the rated one under random input freight traffic. Such an adjustment is possible when the system of a controllable thyristor electric drive on the basis of induction squirrel cage motor is used. Computer-aided adjustment of the belt conveyor movement is effected via bicontour digital control of the main drive in order to redistribute loads when the loading of conveyor and contour of the control of tension drive are changed. The system envisages control and condition monitoring of the conveyor electromechanical system, as well as metering of electrical power and the amount of conveyor freight. The results of the simulation of speed control of the conveyor belt are given in the report. Mathematical model of the conveyor electromechanical system describes the movement of the belt with cargo and the tension drive. The input cargo traffic is assumed as stationary ergidic random process with the assigned characteristics. The solution of the problem of the synthesis of a closed-loop control system, the structure and parameters of adjustment, the conditions of asymptotic stability of the control back-up system and the condition of minimization of mean square error of shadowing are also given in the report. Microprocessor controller is used to realize the function of the adjustment unit. Under this control system standard mode of conveyor operation, different modes of start-up, operating mode with decreased speed when transporting people, service and emergency braking of a conveyor and some other modes are realized. The digital model of a conveyor as an instrument for decision making in case of emergency is used in those modes. MASTER TEXT Long-standing practice of belt conveyor operation in mines of Russia has proved their inefficient use with 40-70% capacity and 20-25% availability factor. It is associated with unreasonable power intensity and reduction of service life of mechanical components, and as a result, with the growth of total transportation costs. Low efficiency of conveyor application can be explained by the extremely irregular distribution of conveyor freight traffic. Usually, the width of a conveyor belt is identified in accordance with the possible maximum traffic value, engine power capacity for long-term operation under rated loads. However, actually a conveyor often runs without any load and its average load in most cases is lower than the rated one. The problem can be eliminated by way of the adjustment of the operational mode of a conveyor according to an actual input freight traffic via belt speed control providing for the conveyor regular linear load which is nearly equivalent to the rated one. Experimental research into freight traffic under working conditions of the operating underground and open-cast mines proves the fact that the actual freight traffic can be adequately presented through the model of stationary random function of time, for ex- ample, as a J (t) continuous random Gaussian process that is modulated with a G(t) elementary pulse flow:

Jan 1, 1996

By J. W. Leonard

Introduction Gravity-based coal/mineral preparation plants must be operated to yield products of a quality satisfactory to existing markets. However, because of historic control problems, recovery is frequently sacrificed to achieve quality, resulting in losses of valuable product. Plant control has ranged from intuitive in-plant spot quality judgments made by various operators to gross methods involving such devices as density gauges, floats, grabsample on-the-spot sink/float tests, etc. Millions of tons of quality coal/minerals are lost to refuse each year, because of the historic lack of a continuous and dependable control system. The result is serious economic, as well as environmental, losses. While the economic losses are obvious, the less obvious environmental ones, in the case of coal, result from the misplacement of more ignitable quality fuel to refuse banks. Until recently, a control system capable of supplying a market-grade coal/mineral product, while continuously minimizing product losses to refuse, has been technologically unavailable. Coal/Mineral Washing Tracer System Performance Monitor (CMWTSPM) The first Coal/Mineral Washing Tracer System Performance Monitor (CMWTSPM) originated in the late 1970s as an innovative idea and ultimately resulted in Leonard Patent No. 4,345,994 issued on August 24, 1982. In a classic example of successful university basic research, the patent was followed by two US Department of Energy (DOE) merit awards for fundamental optimization research at the University of Kentucky, a number of publications, a successful applied research program (underwritten by SENTREX at Irvine, CA) and field tests at the Rochester and Pittsburgh Coal Company Keystone Mine near Indiana, PA. The system is now operational and is marketed by SENTREX as the SENTREX Performance Monitor. A diagram of the system is shown in Fig. 1. This system relies on metal detection as the basic tracing medium. Since it is capable of tracing particles as fine as 0.19-in., the system is ideal for coarse coal/ mineral cleaning processes. Basically, the CMWTSPM records the distribution of synthetic coal/mineral particles, of known size and specific gravity, between product and refuse output streams of coal/mineral washing, gravity-concentrating processes. For any given particle size, surface area and shape are constant. The particles are [ ] designed to find their way into the center of their respective inprocess specific gravity/size streamlines. The system will yield a complete partition curve to show the percentage of misplacement for any selected size/specific-gravity particle fraction, thereby providing a point-to-point insight into process failure. When used to evaluate operational processes, this full partition curve is far more diagnostic than the simplifying, derivative, single index number known as the Ep value. The Ep value is commonly used for convenience to represent symmetrical partition curves, but, if the actual partition curve is non-symmetrical, use of the Ep value can result in serious diagnostic error. While the Ep is useful in design and for rapid performance evaluation and process adjustment, the full partition curve is by far the more diagnostic. It will provide insight into the behavior of particulate flow, through non-symmetry, as a means to highlight potential systemic failures. Performance of the process is measured and improved by determining the extent of particle misplacement and by making timely adjustments to the unit to reduce the misplacement. Used in this manner, the CMWTSPM is not only a long needed processing control monitor, but it is also a very powerful diagnostic tool which, in the hands of skilled operators, has

Jan 1, 1993

By Leslie E. Apodaca

INTRODTUCTION The use of spiral concentrators for processing fine coal particles is an old idea that has recently gained acceptance in the 11.S. coal industry. It was not onti1 the Australian Minerals Industry developed a spiral concentrator specifically for separating coal from ash in the latter 1970's and early 1980's that spiral concentrators were seriously considered as viable equipment for processing fine coal. The Wright Coal Spiral was introduced in 1980, the Mineral Deposits Limited Mark 10 Coal Spiral was introduced in 1982, and the Vickers Wyong Coal Spiral was introduced in the latter part of 1984. Each spiral design was different and utilized constant profile troughs, constant pitch troughs, compound profile troughs, and various splitter arrangements. Mineral Deposits Limited has combined the best features of the compound profile trough and constant pitch trough with critically-placed splitters to develop the MDL LD4 spiral concentrator which is a truly efficient coal washing spiral. This spiral concentrator was introduced into the U.S. Coal Industry in 1987. Recently, Mineral Engineering Technology of the United Kingdom and Multotec of South Africa have introduced their own coal spiral designs. Spiral concentrators were first installed in fine coal processing circuits in the Australian, South African, and Canadian Coal Industries in the early 1980's and in the U.S. Coal Industry in 1985. SPIRAL CONCENTRATOR SEPARATION PROCESS The separation process that occurs within the spiral concentrator trough is very complex, as it is a combination of three gravity separation processes. When the coal slurry first enters the spiral trough, each coal and ash particle and the water is subjected to centrifugal forces. These forces cause the water, light coal particles, fine heavy ash particles, and medium middlings particles to the outer vertical portion of the spiral trough. The coarse ash particles and the coarse middling particles remain on the inside of the spiral trough. The center or transitional area of the trough contains a mixture of middlings particles and near-gravity material that is present in the slurry, as shown in Figure 1. At the same time the coal and ash particles are suhjected to centrifugal forces, the trough design (both profile and pitch) causes the particles to be subjected to flowing film and stratified bed separations. The combination of these three separations, whose efficiency is dictated by the spiral troogh design, will effect the separation of the lighter coal particles from the heavier ash and middlings particles. As the slurry flows down the spiral, the profile and pitch design of the trough will counteract the centrifugal forces on the fine, heavy ash particles and fine middlings particles and cause them to migrate from the vertical portion of the trough to the center or inner portion of the trough. At the same time, any heavy particles trapped in the transitional area of the trough will be forced to migrate to the inner edge of the trough and any coal particles will be forced to migrate to the outer edge of the trough. SPIRAL SPLI'TTEP ARRANGEMENT The critical placement of splitters along the inner edge of the trough for removal of the heavy ash particles as the slurry flows down the trough further enhances the separation of the coal particles. At the bottom of the spiral trough are product splitters arranged to make a final separation of the slurry stream into clean coal, middlings, and refuse products.

Jan 1, 1988

By J. L. Weeks

Discussion by J.L. Weeks Discussion I wish to comment on Kissell and Sacks's paper "Inaccuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines." It is well established in industrial hygiene that area sampling is not an accurate measure of personal exposure. To measure personal exposure, one must use a personal sampler. Kissell and Sacks, using data from coal mining, reached the same conclusion. This is the right answer but it is the wrong question. This issue arises because the machine-mounted respirable dust continuous monitor (MMRDCM) is being considered to monitor coal-miners' exposure to respirable dust. This device may be mounted on a continuous mining machine, and it would take a modified area sample. I refer to it as "modified" because a mining machine is not really a fixed location, as is the typical area sample. The concern with whether this machine would provide an accurate estimate of the machine-operator's exposure, however, overlooks important features of the MMRDCM. Specifically, it displays dust concentration as it occurs and at the place where it is needed, not 10 days later, as is the case with the current system. Used in this way, it allows for timely intervention to control exposure to dust and it leads to greater first-hand knowledge of specific conditions and mining practices that result in excess exposure. If one knows the dust level is excessive at the time the dust is being generated, it is possible to use known and effective methods of dust control to reduce exposure. By measuring again, one can determine whether control methods have worked. This is a generic procedure followed in any industrial process: measure, adjust and measure again. It leads to more effective and more efficient dust control and is preferred to taking a sample, waiting 10 days for the results and then trying to apply that information to a situation that no longer exists. The MMRDCM also records the dust level automatically, and it runs continuously, making it harder to tamper with. Dust monitoring in underground coal mines has been corrupted by some operators having submitted fraudulent samples (and being convicted on criminal charges because of it), weakening the credibility of the current system. The MMRDCM is, in part, a response to this corruption, and an effort to focus attention on dust levels and dust controls rather than on the perpetrators of fraud. Use of the MMRDCM is an evolutionary change from the current system. With the current system, one takes a personal sample of exposure of the "designated occupation" (DO, defined at 30 CFR 70.2 (f)), the occupation regularly exposed to the highest level of dust on a section. Typically, on sections using continuous mining machines, this is the mining-machine operator. The rationale behind DO sampling rests on some of the findings that Kissell and Sacks report. They reviewed several studies that showed that dust concentration varies with location on a mining section and that there is a concentration gradient with the highest concentration occurring closest to the face. The logic behind DO sampling strategy is that if the dust concentration at the place where it is highest is below the exposure limit, then concentration elsewhere on the section is also below the limit. In this way, one will have achieved the objective or keeping dust concentration below the exposure limit for all miners on the section by measuring the exposure of only one miner. The

Jan 1, 2003

By Mark D. Cocker

Georgia?s Coastal Plain contains important sediment-hosted deposits of kaolin, bauxite, heavy minerals, sand and gravel, silica sand, carbonate rocks, and fuller's earth. Genesis, location, size, and quality of these deposits are related to terrestrial, marginal-marine, and shallow-marine depositional environments that evolved during development of the southeastern North American continental margin. From the Cretaceous to Eocene, kaolin and aluminous sediments, which contained mica and feldspar, were deposited in marshes, ponds, and bays located in deltas or behind barrier islands or spits. In the Cretaceous sediments, subsequent, intensive, in situ chemical weathering converted mica and feldspar to kaolin. Kaolin eroded from deeply weathered granitic rocks in the Georgia Piedmont was deposited in Paleocene to Eocene sediments. Subaerial exposure during the Paleocene and Eocene desilicated kaolin sediments to form bauxite. Sand and gravel, silica sand, and heavy-mineral deposits are found in Cretaceous to Eocene fluvial and shoreline sediments, some of which are associated with the kaolin and bauxite deposits. Source areas, intensive chemical weathering in the source areas, transportation by the major river systems, and deposition of these clastic sediments in similar or nearby depositional environments are common elements in the genesis of these resources. Eocene fuller's-earth deposits are opaline claystones in near-shore to shelf-marine sediments, which overlie the kaolin-bearing strata. These claystones consist of montmorillonite and opal/ cristobalite derived from alteration of diatom frustules. Favorable ocean currents provided nutrients for extensive planktonic growth. Oligocene and Miocene carbonate rocks were deposited principally in shallow-marine embayments. Miocene fuller's- earth deposits in south-central Georgia and adjacent parts of Florida contain palygorskite that formed through alteration of montmorillonite/bentonite clays. Deposition and subsequent alteration occurred in shallow, brackish-water lagoons under relatively high temperature and subtropical conditions. Middle and late Miocene phosphorites were deposited on a shallow carbonate-shelf platform and were concentrated proximal to anticlinal highs. Numerous marine transgressions and regressions since the beginning of the Pleistocene resulted in shoreline detrital deposits containing aggregate sand, silica sand, and heavy minerals on the Coastal Plain and on the Continental Shelf. Major river systems transported sand and heavy minerals from source areas in the Piedmont and Upper Coastal Plain. Deltaic deposits of heavy minerals were redistributed and concentrated by longshore currents, shoreline processes, and aeolian processes. River-terrace sediments, correlative with the Pleistocene shoreline deposits, contain sand-and-gravel and silica-sand deposits. Aeolian dune sands are associated with both Pleistocene fluvial and shoreline detrital deposits.

Jan 1, 1999

By Diane Moody

I have been asked to give you the National Coal Association's (NCA) view of the future of the coal industry. However, before discussing the outlook for the future I would like to set the stage by taking a brief look at how the industry has changed over the last decade. In 1977 the coal industry was in the midst of a period of steady growth. Although most of the gains in the early and mid 1970's occurred in the west, the industry was still predominately eastern, with eastern production accounting for 76 percent of the 697 million total tons produced in 1977. The labor force was nearing a high - at over 220,000 workers, and the number of active mines was also at a decade high of over 6,000. Productivity on the other hand was at a low. The average miner produced 1.80 tons per hour, and labor relations were also at a low point. Projections for coal's future were very optimistic, mainly because of the unprecedented growth in coal use by the utility industry. In 1977 the 477 million tons of utility coal accounted for 68 percent of U.S. coal production, and the utility industry planned on 129,000 MW of new coal-fired capacity over the next decade. Consumption of metallurgical coal at coke plants was the second largest market at 78 million tons; the industrial and residential market consumed 70 million tons and exports were at 54 million tons. But in retrospect, a lot was happening in 1977 that signalled many changes in the coal industry: - Amendments to the Clean Air Act were passed, which required that utilities take an entirely different approach to meeting New Source Performance Standards at new plants, and required that standards be set for industrial boilers as well; - the Surface Mining and Reclamation Act became law; -electrical generation, despite the optimistic forecasts, was nearing the end of a period of close to five percent annual growth; -1977 ended and 1978 began with the longest coal strike in U.S. history. -crude oil imports in the U.S. reached an all time high as did both total consumption of petroleum products in the U.S. and oil consumption at utilities. The high level of oil imports set the stage for the oil price increases of 1979 and 1980 which resulted in an immediate increase in demand for coal, not only in the United States, but world wide. Labor strikes in Australia and Poland sent foreign buyers to the U.S. literally in droves, and quickly made the U.S. a force in the world steam coal market. The U.S. coal and transportation industries responded to this overwhelming potential demand for coal. In a very short time, the capability had been developed to mine and transport the 1.2 billion tons of coal that forecasters said would be needed by the mid 1980's. What was not anticipated was that the economic effects of sharply higher oil prices would dampen demand for energy, especially for electricity, as quickly as we have seen; that coal industries in other countries would respond as rapidly as the U.S. coal industry, and at a rate

Jan 1, 1988

By Bing Wang, Jingli Fan, Qinying Song, Fengyu Li, Xian Zhang

"With the background of water shortages and serious water pollution, issues of water involved in energy exploration and utilization have become critical problems affecting urban water usage. In order to identify the relationships of the energy-water nexus, this paper characterizes the energy-water nexus literature using a bibliometric method and based on the Chinese National Knowledge Infrastructure database platform. The results reveal that 1) Scientific outcomes in this field have increased sharply since 2003, with a slightly higher growth rate than that of general disciplines. 2) China Water Resources, Yangtze River and Express Water Resources & Hydropower Information are the dominant journals, and the main research fields include industrial economics, environmental science, and management, among other disciplines. 3) Hohai University, the Chinese Hydraulic Engineering Society, the Institute of Geographic Sciences and Natural Resources Research, and the Changjiang Water Resources Commission are the main research institutions in this field. However, the proportion of publications of these institutions is not high, which suggests that there is no institution dominating this field. 4) According to the keyword analysis, the hot spots in this field include ecological environment, sustainable development, environmental protection, climate change, etc. Energy-mining related keywords have increased over time, implying that the energy-water nexus from the perspective of the energy exploitation industry can become a key issue. At the same time, the frequency of keywords related to sustainable development has been maintained at a high level, and the studies concerned with the impacts of climate change were introduced into this field relatively late. The conclusion of this study provides a foundation for a comprehensive understanding of the current situation as well as for further research in the energy-water nexus field.Introduction As an important strategic resource for national economic and social sustainable development, water has been increasingly focused on by the Chinese Government. Over the next decade, the total water demand of China will continue to grow steadily, which lead to a significant trend of increasing water consumption in the future (Zhang 2013). To reasonably exploit, utilize, conserve and protect water resources, the Water Law of the People's Republic of China was enacted by the members of the 9th National People's Congress Standing Committee in 1988 and after multiple revisions, the latest of which, in September 1, 2016, has involved water infrastructures in the national economic and social development plans of the government at all levels and regulated the rationale for water engineering construction. Thus, in the context of serious water shortages and water pollution, China’s government has taken several measures to make rational use of water resources."

Jan 1, 2017

By B. Hearn, O&apos

Falconbridge, Ltd. operates six mines (the strathcona, Fraser, Lockerby, Onaping, East and Kidd Creek) in the Sudbury and Timmins districts of northern Ontario (Fig. 1). These mines vary in depth to approximately 1500m and experience a wide variety of ground conditions. Problems of greatest concern include rockbursting, backfill pillar stability, wall and pillar stability, and the use of cable anchors. A study was initiated approximately two years ago to identify how numerical models could aid in the examination and possible understanding or solution of these problems. This paper discusses the use of numerical models at Falconbridge and describes a case history of their use in examination of rockbursting at the Strathcona Mine.

Jan 1, 1988

By Kenneth A. Gutschick, Harry L. Francis

A large number of minerals and chemicals (Table 1), some mineral-derived, are used in the treatment of both potable water and domestic sewage waste water and solids (Anon., 1990). In water treatment there are ten principal process uses as shown in Table 2 (Anon., 1990), which also lists the major chemicals in each process. Since lime (calcium oxide, calcium hydroxide, and dolomitic lime) is the largest chemical (by tonnage) used in water treatment, this chapter will deal primarily with this product. Note that it is included in five of the process uses shown in Table 2, and that indirectly it is also used in at least one other category (taste and odor control, where lime is used with potassium permanganate to provide optimum pH condition). POTABLE WATER TREATMENT Water Softening The biggest use for lime in water treatment involves water softening, where it serves to reduce carbonate hardness caused by dissolved bicarbonate and carbonate compounds. Currently there are more than 1000 domestic water softening plants (Table 3) located in most sections of the country, but particularly in Ohio, other midwestern states, Florida, and Texas, where limestone bedrock abounds (Anon., 1990). Among the other uses for lime in water treatment are coagulation, disinfection, and removal of heavy metals due to high pH softening, removal of certain radioactive and organic compounds and fluorides, neutralization of acidic water, removal of silica, particularly with dolomitic lime, and removal of color. Most of the above advantages accompany water softening, although at some plants lime is used specifically for one purpose, such as silica removal with dolomitic lime, minimizing pipeline corrosion by addition of lime to correct an aggressive water, and others. Hardness in water comprises two types - carbonate hardness, caused by dissolved calcium and magnesium carbonates and bi- carbonates, and non-carbonate hardness caused by dissolved non- carbonate salts, particularly calcium sulfate, calcium chloride, magnesium sulfate, and magnesium chloride. Total hardness is the sum of the carbonate hardness and non-carbonate hardness. Waters are classified as soft (0 to 75 mg/L as CaCO,), moderate (75 to 150 mg/L), hard (150 to 300 mg/L), and very hard (above 300 mg/L). Most water plants strive to reduce total hardness to about 100 mg/L, although in recent years the tendency in some cities has been to allow a little higher value in order to reduce both chemical costs and the amount of water softening sludges produced. There are four basic types of softening plants: lime softening, primarily to reduce carbonate hardness; lime-soda softening, for reduction of both types of hardness (in some plants caustic soda is used in place of soda ash, but it is more costly); split lime-zeolite, where a base exchange mineral is employed in place of soda ash (this system also requires salt [sodium chloride] to regenerate the zeolite mineral); and finally zeolite softening, which is generally used in small systems for private houses and small municipalities. Principal disadvantages of the latter system are its relatively high cost and the salt requirement, which introduces considerable quantities of soluble salts into the waste water discharge system.

Jan 1, 1994

By Alfredo Valdivia, Hamed Nejad, Vincent Monaco, William Cao

"The East Side Access (ESA) CM005 Contract - Manhattan South Structures - consists of the installation of the waterproofing and final concrete lining for railroad tunnels, 3-Level Wye track turnout structures, segments of the Main Cavern Station, and a series of Ventilation Structures excavated beneath the existing Metro North Railroad (MNR) Grand Central Terminal. Several key team decisions made collectively by the Construction Manager (CM), Designer, and the Contractor has allowed the scheduled construction duration of 29 months to be maintained. These strategies include the use of alternate design and construction methods, including the use of pneumatically applied concrete lining and precast lining. This paper discusses these strategies, and illustrates how successful teamwork and cooperation during the execution of a large-scale construction project can lead to lowering costs, improving quality, and maintaining the overall project schedule. INTRODUCTION The East Side Access Project The Long Island Railroad (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already over congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodate the NJ Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the NYCT Subway System and Metro North Rail Road. The ESA Project includes building new tunnels and facilities under Manhattan and Queens. (See Figure 1).The Manhattan Alignment In the Manhattan segment of the ESA Project the excavation in hard rock of tunnels, cross passages, caverns and shafts has been completed by tunnel boring machines, drill and blast, and road header. The construction of the structural concrete final lining, interior structures and fit-out of the previously excavated caverns and tunnels are currently being performed under Contract CM005 Manhattan South Structures awarded to Michels Corporation and Contract CM006 Manhattan North Structures awarded to Frontier Kemper Constructors Inc. This paper focuses on the design and construction aspects of Contract CM005 which is the first ESA Contract in Manhattan to successfully construct concrete final linings in pre-existing excavated areas."

Jan 1, 2016

By W. L. Oliveira, J. R. Sobrinho, V. M. Hamza, S. M. Eston

The Ipueira III chrome mine is located in the northeastern part of the state of Bahia, Brazil. Extraction is actually at depths less than 300 m, but below level 200 serious environmental problems have been encountered with respect to control of air quality, toxic gas, dust and thermal comfort. At the request of the mining company the University of São Paulo started a research program to investigate the origin and occurrence of the critical problems and to propose solutions. A ventilation survey was carried out first which revealed the existence of several air leakages and short circuits that contributed to substantial reductions in the air supply to some of the main producing levels. Computer simulation of the ventilation network showed that extending the intake air shaft to deeper levels was the most convenient and economic solution to improve the air quality. The ventilation survey was followed by a mapping of the toxic gas emissions and thermal comfort levels in several parts of the mine. The air quality conditions were evaluated as a function of gas emission and heat generation associated with production and development activities. The results show that environmental conditions are already critical in most of the working levels and neither an increase in production nor deepening of the mine can be taken up without substantial changes in the ventilation system. INTRODUCTION Environmental concern is growing in Brazil and several underground mines are starting environmental engineering programs. The LACASEMIN - Laboratory of Environmental Control and Mine Safety of the Mining Engineering Department of the University of São Paulo - was contacted by Mineração Vale do Jacurici to start a research program for investigating the origin and occurrence of environmental problems that existed in the Ipueira III chrome mine. This research program involved field measurements of air quantities with gas levels monitoring, evaluation of heat stress parameters, determination of adequate flow patterns through computer simulations and training of mine technical staff. This paper presents the results of the first 4 months of this research program. The Ipueira III mine is located in the northeastern part of the state of Bahia, near the city of Senhor do Bonfim at about 400 km inland from the state capital city of Salvador. Chromite mineralization is quite widespread in this area and often associated with mafic and ultramafic rocks which cut across regional gneisses and migmatites. ROM production in 1992 varied between 25,000 to 40,000 tons per month, 25% being of lump type (38% of Cr2O3) and 75% being of fines. Lump is manually separated and fines are concentrated in a nearby plant. All the production goes directly to the group processing steel plants near Salvador. The Ipueira III mine is currently under some adverse economic situation because of imports from South Africa and Russia, which have better grades and sometimes a lower content of phosphorous. Consequently there has been little progress in the development of new mines and even in those currently under operation the extraction is becoming more difficult due to the lack of investment in improving mining methods and ventilation systems. In spite of such difficulties the company has backed up studies for initiating an environmental engineering investigation of the Ipueira III mine. MINING METHODS AND VENTILATION SCHEMES The mining methods adopted have changed as a function of extraction depth, rock mass strength and ore body geometry. Initially the orebody was found to be fairly continuous and dipping at about 55 degrees from surface

Jan 1, 1993

By C. A. Rowland

Introduction Comminution efficiency, as measured by relating circuit performance to the consumption of energy and the time and money required, can be determined by the following comparisons: Theoretical efficiency: The theoretical efficiency is the actual energy consumed in a comminution machine compared to the theoretical energy required to perform the size reduction. Operating efficiency: The operating efficiency compares the operating work index of a comminution machine to the Bond work index of the ore, as determined from bench-scale crushing and grindability tests or pilot-plant tests. Economic efficiency: The economic efficiency is comparing income from production to predicted income. Key words: Comminution, Bond work index, Grinding, Crushing, Ball mills, Rod Mills. Theoretical efficiency In their book Process Engineering of Size Reduction - Ball Milling, Austin, Klimpel and Luckie (1984) stated that, "We have tried throughout this book to avoid the use of the term grinding efficiency because the degree of conversion of energy to useful size reduction is an ill-defined concept. In addition, the only efficiency, which is of real interest, is the meeting of product specifications at the minimum cost." The National Materials Advisory Board, National Re¬search Council (1981), in the abstract of a report titled "Comminution and Energy Consumption" stated that, "Up to 99% of the energy consumed in grinding these ores may be expended in the movement of machinery, with noise and heat the undesirable byproducts, thus leaving only 1% of the energy available for size reduction. Coupled with this is evidence that many of today's crushing and grinding techniques not only are antiquated but have little or no scientific base of understanding." Throughout the past 50-plus years, grinding efficiency has been referred to as being from 1 % to 10%. The measurable basis for these observations is difficult to establish, but they appear to be based on production performance compared to theoretical energy requirements for the work done. The theoretical energy requirements were determined from the energy required to break a single particle or a thin layer of monosized particles by compression or by a single impact from an impact-testing device. King, Tavaras and Middlemiss (1997), in a paper titled "Establishing the energy efficiency of a ball mill" described such a test. These batch single-breakage tests generally do not duplicate the continuous-breakage process in the comminution machinery used in ore concentrators. Operating efficiency The currently available crushers and grinding mills are fed at a controlled continuous flow rate, and they impart the breakage pattern needed to produce the desired size reduc¬tion. While theoretically inefficient, they are the most practical comminution machines available. The operation of this machinery is relatively simple and can be controlled with available control systems. The essential factors in determining the operating efficiency of comminution machines are energy, as consumed in the machinery, and the required energy, as determined from test work. Bond work indices, obtained from bench-scale or pilot-plant crushability and grindability tests are used in the following Bond equation (Bond, 1960) to determine the energy required to produce the required size reduction

Jan 1, 1999

By Alfred Weiss, Andrew E. Nevin, Thomas J. Neil, O&apos

As Edward E. Runyan, 1983 AIME President, in an interview excerpt in ME, June, p. 607, stated, "...the AIME Transition Committee has recom¬mended to the AIME Board that each Constituent Society be allowed the option of separate incorporation, whereby each could become its own separate legal entity." Background The American Institute of Mining Engineers (AIME) was formed in 1871 by 22 engineers in Wilkes-Barre, PA. Although originally a mining organization, it became a home for metallurgists, iron and steel industry people, and for the individuals in the expanding petroleum engineering profession. There are now four Constituent Societies: Society of Mining Engineers, located in Littleton, CO, 29,000 members; Society of Petroleum Engineers, located in Dallas, TX, 47,500 members; The Metallurgical Society, located in Warrendale, PA, 10,000 members; and Iron and Steel Society, located in Warrendale, PA, 6,500 members. Each of the four groups has grown and continues to serve the specific and/or diverse needs of its membership. As the needs and requirements of their industries and professions change, each of the Societies has perceived and initiated programs that serve their constituency rather than AIME as a whole. Therefore, each Society has recognized an increasing need for autonomy to better augment their own programs. An AIME Ad Hoc Transition Committee, with Robert Merrill, AIME Past President, as chairman, made a number of recommendations pertaining to AIME operations that were approved in October 1982 by the AIME Board of Directors. One of the recommendations was to endorse separate incorporation of the Constituent Societies on an individual-society-option basis. The AIME Board commissioned a task force of Constituent Society representatives to develop specific revisions to the AIME Certificate of Incorporation and the AIME Constitution and Bylaws. This was done to allow separate incorporation and to reflect the decentralized structure of the Institute. The SME-AIME Board of Directors subsequently approved the recommendation of SME Working Party #69 that SME pursue separate incorporation. Meanwhile, Working Party #69 continues to work with the other Constituent Societies and with the AIME Task Force on Reorganization to determine the form and substance of the separate incorporation. Why Incorporate? George Webster in The Law of Associations quoted Chief Justice Marshall's (1819) definition of corporation as: "A corporation is an artificial being, invisible, intangible, and existing only in contemplation of law. Being the mere creature of law, it possesses only those properties which the charter of its creation confers upon it, either expressly or as incidental to its very existence. These are such as are supposed best calculated to effect the object for which it was created." SME-AIME attorneys, Davis, Graham & Stubbs, have pointed out that the status of an organization operating as an unincorporated association is always unclear. At present, SME-AIME administers assets of almost $3.5 million (mainly property and inventory) but technical ownership and ability to enter into contractual relationships resides with AIME. However, the operation appears to outsiders (particularly those with whom SME-AIME does business) to be an independent operation which would be expected to be a legal entity in its own right. Advantages of Incorporation Liability. Because of legal ownership by AIME of all assets of the Constituent Societies, those assets are subject to the claims of any of the creditors of AIME or any of its constituent parts (i.e., the other societies). Liabilities can be those usually encountered in business but also encompass special risks, which could develop if there were a careless and erroneous publication of material that might be used in practice or if standards are improperly established. The recent US Supreme Court decision in American Society of Mechanical Engineers, Inc.,

Jan 10, 1983

By Peter Joralemon

Introduction The Sierra Nevada Foothill Gold Belt in California extends from Mariposa north for more than 420 km (200 miles). It includes the Grass Valley and Alleghany districts in the zone of Northern Mines and the famous Mother Lode to the south. The gold belt has produced more than 3.1 kt (100 million oz) of gold since its discovery in 1848. This remarkable production, at the present gold price, would be valued at more than $40 billion. The Law of Gambler's Ruin supposes that averages are based on systematic rather than random variations. It emphasizes the vast differences between finite and infinite probability. By applying this Law to this figure, it can be seen that the belt has produced an average of 15.5 t (500,000 oz) of gold per running mile. Many geologists believe, with some justification, that less than half the gold in this belt has been mined. Sixty per cent of the past production has come from lode deposits, the balance from Tertiary and Recent placer gravels. This paper will concern itself with the developing lode mines along the Sierra Nevada Foothill Gold Belt. As a further and final note regarding placer mining along this belt, Mark Twain suggested that placer miners, having lost their senses, had contributed liberally to the population of California's insane asylums. After a 40-year lull with little or no gold production, the lode mines of this famous belt are showing signs of renewed activity. Two open pit mines, the Sonora (Jamestown) and Carson Hill, are now in operation at substantial scales. Two others, the Goldenbell (Pine Tree-Josephine) and the Royal-Mountain King, are being readied for production on equally impressive scales. All are in the southern part of the Mother Lode. Exploration farther north, at Sutter Creek, Drytown, and Georgetown, is showing encouraging results in developing deeper lode deposits. This new activity has been sponsored to a large extent by junior Canadian mining and exploration companies. Most of the established American mining companies have looked the other way, not participating in this important development. One major reason for domestic disinterest in this opportunity is there is little chance for heap leachable open pit ore in this belt, excluding Carson Hill. And heap leaching has become fashionable with American mining companies today. Also, this great old gold belt must have been worked out, for why else is there so little activity here - Catch 22 logic. Another reason is that if a new deposit of size and grade similar to the mines in the past was found, high costs would preclude a profitable operation. And, finally, California environmentalists would not permit mining, even if a rich deposit were found. These may all be pefectly valid reasons not to explore for gold along this belt. But a look at the history of gold mining in California may suggest that the future for exploration and development of the gold resources in the Sierra Nevada Foothills can be greater than the past. It was during the Depression of the 1930s that this gold belt saw its maximum activity, with more than 3000 mines in operation. Some were father and son operations producing only a few tons of ore a day. Other mines employed hundreds of miners to hoist more than 900 t/d (1000 stpd). Some ores were of marginal grade. Others, like the Sixteen to

Jan 7, 1987

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By P. N. Eksteen, G. E. Greig

The South African mining industry currently installs about 6 km per month of plastic pipes for conveying compressed air and water. Plastic pipes have a number of desirable properties and are favoured by many mining engineers because of their low mass, which facilitates ease of erection and assembly, and their excellent corrosion resistance and durability. However, they are combustible, and if involved in an underground fire can contribute to the overall toxicity of the combustion gases emitted. Furthermore, plastic pipes have the potential to conduct a fire from one part of a mine to another, and, by so doing, exacerbate an already hazardous situation. The limitations of small scale tests and the need to establish a large facility where underground conditions could be simulated was recognized by the South African mining industry. This paper briefly describes the Industry's full scale fire test facility and presents the conclusions drawn as a result of a number of full scale combustibility tests conducted on pipes manufactured from unplasticized Poly Vinyl Chloride (uPVC) and High Density Polyethylene (HDPE). Based on these findings, some practical solutions to prevent the spread of fire along the length of pipe columns of various pipe diameters and suspension configurations are presented. Recently some new and exciting developments in the field of intumescent coatings have occurred which are proving effective in minimizing the incidence of fire underground on South African mines. The potential benefits of these coatings are briefly discussed. INTRODUCTION Plastic pipes used underground on mines are predominantly in the form of protective cladding on insulated chilled water pipes and as service pipes for the conveying of water and compressed air to the workings. Plastic pipes have found wide use in the aggressive environmental conditions encountered underground due to their favourable properties relative to steel; these include being lightweight, easily installed and virtually immune to corrosion. However, plastic pipes are inherently combustible and can contribute to the overall hazard in three ways: (i) they are easily ignitable and can provide the initial fuel for a fire. (ii) once ignited, they can propagate a fire along their length and by so doing ignite other combustibles in their path, thereby contributing significantly to the overall conflagration. (iii) they can contribute to the overall heat, smoke and toxic gas emissions from a fire. While conscious of the value of small scale fire tests, the South African mining industry recognized the need for full scale testing to determine the combustion characteristics of plastic pipes under conditions closely approximating those underground and, as a consequence, a full scale fire tunnel test facility was commissioned with the objective of being able to (a), accurately evaluate the potential hazard of the various types of the plastic pipes found in mines, (b) use this information to suggest suitable fire engineering practices to minimize the hazard and (c), to practically verify the efficacy of the practices suggested. THE FIRE TUNNEL The fire tunnel is situated on a mine in the Western Transvaal and is 40 m long with a cross section of 3 m x 3 m which is typical of many haulages currently in use in South African gold mines. The ventilation drawn through the tunnel is provided by a 110 kW centrifugal exhaust fan and air velocities can be varied from 0 to a maximum of 5,8 m/s.

Jan 1, 1993