Search Documents

By Nigel Pearson, Malcolm J. McPherson

In the Grasberg Mine, a series of orepasses of diameter 2 to 4m are being constructed, each one to carry as much as 10,000 tlhour of copper- and gold-bearing ore through single stage vertical drops of over 500m. At the base of each orepass, the fragmented rock falls into an orebin of diameter 1 Om and 100m deep. Long before the planned tonnages were reached on the early orepasses, a problem arose that was both serious and intriguing. Pressurization of air in the orebins caused by the falling rock reached such levels that when the feed to the top of an orpass was interrupted, a massive surge of air ascended rapidly and produced a dangerous backblast accompanied by dust; grit and rock fragments from the top of the orepass. Backblasts lasted for about one minute and were not only hazardous to the health and safety of personnel but also required time-consuming clean-up operations. The paper describes the aerodynamic analyses that were con- ducted in order to understand fully the mechanisms involved in the phenomenum, and the development of a procedure that al- lows the effects of falling material to be incorporated into existing ventilation network software.

Jan 1, 1997

By Kenneth N. Han, Yuhong Chen

The removal of carbonaceous material from Carlin gold ore has been investigated via froth flotation. The effect of type and concentration of various oils as flotation collectors and of sodium silicate as the dispersion agent on the overall recovery of carbonaceous material has been studied. Other variables affecting froth flotation efficiency were also examined closely. These included particle size, pH of the solution, and temperature. The effect of reduction and oxidation of carbonaceous material on froth flotation efficiency has also been investigated. This investigation showed that aromatic type oil was the most effective collector. Also found in this investigation was that oxidized carbonaceous material was difficult to float unless the oxidized portion was subject to reduction before flotation. More than fifty percent of the carbonaceous material was able to be removed via froth flotation. It can be concluded from this study that the effect of pH and temperature during the rougher flotation state is of little significance to the overall recovery of carbonaceous material. Since pyrite is responsible for the high consumption of chlorine, removal of pyrite is very important in order to reduce the overall consumption of chlorine.

Jan 1, 1990

By P. Bevilacqua, G. Ferrara

The paper discusses the problem of accuracy in the determination of the partition curve of gravity separation processes, which is strongly affected by both the sharpness of separation of the density analysis system used and the width of the density range selected. The problem is important when the density analysis of the separation products cannot be performed using heavy liquids, but has to be performed using heavy suspensions or using other systems such magnetogravimetric separation. The imperfect separation given by these systems and the use of large density ranges lead to the determination of apparent partition curves instead of actual partition curves for the process. In the paper the relation between apparent and actual partition curves is studied under different conditions through a simulation program. For different input data, special diagrams are given which, once the apparent partition curves and the sharpness of the density cuts are known, allow calculation of the actual partition curves and the related parameters.

Jan 1, 1995

By Walter E. Heinrichs

This case history really started during the tail end of WWII when two Navy men, both Colorado School of Mines graduates, got together in Washington, DC, while they were assigned to the Office of Navy Petroleum Reserves doing some of the first aerial magnetometer work ever done on a practical oil exploration basis over the offshore area of the Gulf Coast. When separated from Naval Service active duty in 1946, the two men, Walter E. Heinrichs, Jr., and Robert E. Thurmond, tried, unsuccessfully, to form a commercial air magnetometer business. Later they got together again in Jerome, AZ, with Newmont Mining's early geophysical exploration endeavors from 1947 to 1949. Subsequent to the Newmont experience, they jointly proposed a specific mining geophysical exploration and development program to Herbert Hoover, Jr., then president of United Geophysical Co. of Pasadena, CA. Mr. Hoover, in consultation with his father Herbert Hoover and others of his staff at United, particularly Edwin G. Schempf, executive vice president, and Raymond A. Peterson, vice president of research, agreed to establish the proposed program under United's auspices, to be headquartered at Tucson, AZ. The primary objective would be to practically test and develop various mining geophysical methods and techniques while exploring particularly for base metals in the general area of southeast Arizona and southwest New Mexico.

Jan 1, 1991

By V. J. Kecojevic, W. A. Wilkinson

Mining companies are increasingly looking at Global Positioning System (GPS) technology coupled with 3D mine planning and visualization systems to deliver increased productivity and reduction in operating costs in drilling and blasting operations. Leveraging GPS into drill and blast operations requires that a drilling plan be developed and imported into the GPS to guide the operation to a planned and desirable outcome. State-of-the-art mine planning software systems provide the engineer with a 3D environment in which to design and visualize drill and blast plans. This paper discusses producing and exporting 3D drill and blast plans to GPS and how some coal companies are utilizing GPS and mine planning software technology in the drill and blast process.

Jan 1, 2004

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The term unsaturated flow refers to the conditions in which soil pores are filled partially with water and partially with air. This situation constitutes a porous material filled with immiscible fluids. Immiscible fluids by definition exhibit a distinct interface when in contact with each other resulting in a pressure discontinuity across the interface due to surface tension. The fluid that tends to wet the solid particles is called the wetting fluid and the other is the nonwetting fluid. In the air-water sys- tem, air is the nonwetting fluid and water is the wetting fluid. A somewhat analogous fluid system is that in a petroleum reservoir in which there may be up to three immiscible fluids-oil, salt water, and natural gas. The degree of wettability of the fluids is salt water + oil + gas. That is, salt water is the wetting fluid at any interface and oil is the wetting fluid at an oil-gas interface but is the nonwetting fluid at a water-oil interface. Since the oil-water and air- water systems are similar, much of the theory and methods of analyses for the air-water system or unsaturated flow have evolved through the petroleum literature. In the two-fluid system the pressure difference across an interface depends on the size of the pore space in which the interface occurs. The equation commonly used to represent this dependence is

Jan 1, 1986

By Neal Rackstraw, Mamo Meaza

Washington Metropolitan Transit Authority Section E8a consists principally of twin tunnels 1,713 meters (5,620 ft) long, excavated to a diameter of 6.35 meters (20.83 ft) using an open face shield, with a primary lining of four unbolted precast concrete segments expanded at the crown, and a full circle unreinforced concrete final lining with a finished tunnel diameter of 5.08 meters (16.67 ft). The tunnels, constructed in Cretaceous age sediments, are mostly in stiff to hard clay except for a few areas along the alignment that contain dense to very dense fine sand in the upper portion of the tunnel that created a mixed face condition. At two locations unexpected heavy water inflows produced very serious problems in both tunnels. Water flows in the interface area were generally more than 378.5 1pm (100 gpm) and reached as high as 2,649.5 1pm (700 gpm) in the mixed face ground. The nature of the tunnel inflows, the consequences, and the corrective measures adopted will be the subject of this paper.

Jan 1, 1991

By V. Kontogianni

The underground extraction of coal is associated with ground movements extending from the mining area to the ground surface, which result in bowls of ground subsidence, with amplitude exceeding the amount of several meters and occasionally with important tilt and curvature of ground surface. Such changes at both the underground environment and surface topography lead to destruction of buildings, failure of utilities and transportation networks, and occasionally formation of areas vulnerable to flooding, or even small pools. Based on geodetic surface measurements of ground elevation changes, various theories and empirical models relating surface subsidence with the geometry of underground voids formed have been proposed, and predictions of expected subsidence in the form of contours have been estimated. In this study a case study of planning of a new highway network through areas in which coal extraction was also planned is discussed. This work is partly funded by EU. The optimum solution selected was a modification of the initial highway planning, so that the road is increased in length and by-passes the richest coal-field, where maximum post-exploitation subsidence was predicted, and only crosses either minor coalfields, which are not to be exploited, or even margins of main coalfields, in which minor post-exploitation subsidence is expected.

Jan 1, 2006

By Erich U. Petersen

Discussion by Erich U. Petersen Harbuck et al. (1990) present results of research on sulfuric acid leaching of a germanium-gallium ore and shed considerable insight on possible extraction methods for gallium and germanium. However, the presentation does not give sufficient details to evaluate the research, so some of the conclusions may not be as applicable as stated. The objective of this communication is to indicate that relevant and easily obtainable geological and technical information was omitted. Consequently, on this basis, alternative explanations for some of the data are possible. Discussed below are the omission of: • pertinent geological, mineralogical and geochemical literature; • details regarding the determination of germanium concentration in quartz by electron microprobe; and • details on the calculation of the amount of germanium locked in quartz. "These topics are important since the determination of the amount and locus of "unrecoverable, locked germanium" may have an important impact on the economics and methods of germanium extraction and the directions of future research. Harbuck et al. state that "A key to increasing germanium extraction is understanding the mineralogy of the ore." However, only two studies are cited that in some manner describe the mineralogy of the ores. In addition, both of these studies were very preliminary, of limited scope and examined very few

Jan 1, 1993

By S. Kelebek, G. W. Smith

Four samples of galena, each prepared differently, dry ground chalcopvrite and real gar have shown various quantities of liberated sulfur corresponding up to nine equivalent monolavers on their surfaces as determined by the solvent extraction/UV analysis of sulfur using ethanol. The pretreatment of a dry ground galena sample with acidified ammonium chloride or neutral, saturated sodium chloride solutions rendered the mineral readily floatable. The collectorless floatabilities of galena pretreated with the former solution and of drv ground chalcopvrite have been evaluated in reference to the natural floatability of sulfur using the critical surface tension of floatability approach with aqueous methanol solutions. It is shown that the amount of sulfur- on these samples can be correlated with their flotation rate, which was found to he first order within the critical surface tension range. The larger the concentration of surface sulfur, the faster the sulfide mineral floats, thus, the greater its flotation rate constant.

Jan 1, 1990

By F. G. Miller, M. Polat, S. Chander

Flotation was used to achieve improved separation of magnetite from the float and sink products obtained from heavy medium separation and to reduce the load of the medium cleaning circuit. The investigation was carried out in two successive phases. In the first phase, tests were performed on in-plant samples from the Homer City Coal Perdition plant to determine what effects variables such as medium density, particle size and magnetite source had on the efficiency of the process. In the second phase, the optimum conditions determined in the first phase were used to determine the applicability of the process to other selected coals from central Pennsylvania. It was observed that flotation was very effective in the separation of magnetite from coal. In most of the cases investigated, the magnetite recovery was approximately 99% with a magnetite grade ranging from 95 to 99%. The grade of the magnetite decreased as the ash content of the coal increased and the particle size of the magnetite decreased.

Jan 1, 1994

By P. H. Williams

Experiences gained using computers in the mining and geological environment have shown that it is quite rare for a system or the data it stores to be truly stand alone. Just as the mining enterprise aims to have a smooth integration of operations from exploration through mining and extraction to sales, so it should develop all its information systems within an overall framework or architecture which covers the applications and data as well as the computer hardware and communications. This paper discusses methods of achieving such an architecture, and describes some of the benefits it can have on the development and implementation of information systems. The key aspects are the identification of the business functions and the data that they use, and ensuring that the IS plan supports the overall objectives of the enterprise. Hardware and communications policies should be based on the plans for the applications and data, rather than the reverse.

Jan 1, 1986

By Brian K. Failon

Scale formation is a problem that affects many mineral processing systems because the processes require the use of large volumes of water. Scale composition may vary from circuit to circuit, but the scale deposition mechanisms and needs for prevention are often somewhat similar. Likewise, there is a degree of commonality in the prediction, detection, and elimination of scaling conditions in various water systems. This paper briefly reviews some of the conditions which lead to scale formation, as well as some of the common problems associated with unchecked scale growth. The primary focus of the paper is on the variety of chemical scale inhibitors available for use in mineral processing circuits, and the actions of each type. The means of predicting and detecting scaling tendencies are also addressed, and include both direct and indirect methods, i-e., stability index determination and chemical analysis of deposits.

Jan 1, 1986

By D. Gärtner, A. Oster

"""Operational excellence"" provides a sound foundation for RWE Power AG's three strategic pillars (innovation, expansion and organic growth). The maintenance and development of operational excellence in lignite mining operations at RWE Power is supported by the Continuous Improvement Process (CIP) ""immer:besser"" (getting better). Obtaining cost reductions with the aid of the CIP as a kind of value-adding self-renewal process to ensure competitive lignite mining operations and lignite-based electricity generation forms the basis for further increases in profitability and growth. Since the beginning of the 1990s, RWE Power has carried out a multitude of re-engineering projects focusing on the efficient shaping of processes with the assistance of external consultants to enable the Company to cope with the considerable need for change by swiftly implementing major efficiency levers. These also include the required adaptation and development of the organization. Since 2004, the Continuous Opencast Mine Improvement Process (""KVT"") has enabled the mines to tap significant cost reduction potential by virtue of their own strength. But there is another issue that has come into focus: the development of performance enhancement options. In 2006, the ""KVT"" process, piloted in the opencast mines, was included in the RWE Power-wide immer:besser (i:b) programme (Figure 1)."

Jan 1, 2011

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control can be considered a form of insurance to enhance the value of an exploration or mining project. Providing reliable assay data in a production laboratory is challenging. Pressures such as time constraints and profitability affect data integrity. In Australia and North America, reliable assaying services have been provided by several laboratories. Mistakes are primarily due to human error but systems are available that monitor results and identify these types of errors. As the mining industry expands globally, mining companies encounter difficulties in some of these areas due to lack of infrastructure, poor communications, bureaucracy and political risk. These challenges also apply to the operation of laboratories, enhancing the risk of compromised data.

Jan 1, 1997

By Allen M. Newcome

The Ohio valley division of consolidation coal company has incorporated two new aspects within its coal mining concern. A new communication system, thru the cooperation of the c. & p. Telephone company, has been established in each of our mines with its central control in the general office building. In conjunction with this system, a Texas instruments 960 a computer has been incorporated into the system. The purpose for our computer is to provide modernization and improvement to our safety, production and maintenance programs. Thru proper use, the computer will help eliminate inaccuracies and inefficiences that have previously caused inaccurate analysis of problems. Due to federal requirements for more reliable communications in underground mines, Ohio valley division is making a concentrated effort to improve its communication systems. Systems such as the magneto phone and trolley phone have been looked at more critically. It was found that these systems are being used well beyond their limits. With these facts in mind, division personnel started looking for a system that would have these built in advantages: ease of maintenance and installation, increased reliability, low cost, and an inherent ability as a multiple use system.

Jan 1, 1975

By L. Xu, S Jones, R. Bhaskar, J. McKenzie

The objective of this project was to optimize the ventilation parameters of a continuous miner underboom scrubber. This would result in further control of the amount of airborne dust discharged during mining, reduce the exposure of face personnel for an exhaust brattice ventilation system, and avoid recirculation of contaminants at the face. This research was performed in an underground coal mine in Utah. The tasks performed included preliminary face ventilation evaluation, and optimization of the scrubber system to eliminate recirculation of the scrubber discharge air. Airflow tests were conducted on the currently used dust control system and the modified scrubber system. Tracer gas tests were performed to evaluate face ventilation effectiveness. Confirmatory tests of the scrubber system under actual operating conditions, modifications to the scrubber system and a comparative evaluation of the scrubber system vs. the existing system were performed. This paper presents the results of the airflow pattern tests and the respirable dust levels in the modified scrubber system and the existing system. The optimized face ventilation parameters and the developed operating guidelines may provide the benefits of dust reduction, better lace ventilation and improved visibility.

Jan 1, 1994

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994

By D. Robert Weir, Roman M. G. S. Berezowsky

Pressure oxidation can virtually always render refractory auriferous sulphidic ores and concentrates amenable to cyanidation. Its effectiveness as a pretreatment of refractory gold feedstocks is reflected by the successful startup and operation, over the past four years, of four commercial plants. At least three more are scheduled to come on stream during the next three years. Over the past eight years, a variety of ores and concentrates have been subjected to integrated miniplant testing and process demonstration by Sherritt, and data derived from these studies have been used in the design and construction of several of the commercial facilities. Some factors affecting the selection of pressure oxidation in gold recovery processing are discussed.

Jan 1, 1989

By P. G. Tzeferis

Factory beet molasses media were used as cheap sources of sucrose for microbial leaching of Greek nickeliferrous laterites using strains of Penicillium and Aspergillus sp. Nickel recoveries of up to 62% and cobalt recoveries of up to 50% were obtained by leaching in a two-phase system in which bioacids were produced by fungal metabolism in molasses ferrocyanide pretreated media. The addition of potassium ferrocyanide to the molasses substrates prior to leaching was found to have a beneficial effect by increasing the level of citric acid bioproduction, thus improving the leaching efficiency of the fermentation liquid. The metals known to interfere with citric acid production (i.e., Fe, Cu, Ca and Mn) were those most efficiently precipitated. Considering the much lower commercial price of molasses in the industrial market compared to sucrose and glucose carbohydrate media, molasses could prove to be a promising alternative, despite the cost of the required pretreatment.

Jan 1, 1995